From 802d52734adf0f288c49c05ed433872d7559c932 Mon Sep 17 00:00:00 2001 From: Karen Xie Date: Fri, 13 Feb 2009 21:39:04 -0800 Subject: [SCSI] cxgb3i: Fix spelling errors in documentation Signed-off-by: Karen Xie Signed-off-by: James Bottomley --- Documentation/scsi/cxgb3i.txt | 11 +++++------ 1 file changed, 5 insertions(+), 6 deletions(-) (limited to 'Documentation') diff --git a/Documentation/scsi/cxgb3i.txt b/Documentation/scsi/cxgb3i.txt index 8141fa01978e..7ac8032ee9b2 100644 --- a/Documentation/scsi/cxgb3i.txt +++ b/Documentation/scsi/cxgb3i.txt @@ -4,7 +4,7 @@ Introduction ============ The Chelsio T3 ASIC based Adapters (S310, S320, S302, S304, Mezz cards, etc. -series of products) supports iSCSI acceleration and iSCSI Direct Data Placement +series of products) support iSCSI acceleration and iSCSI Direct Data Placement (DDP) where the hardware handles the expensive byte touching operations, such as CRC computation and verification, and direct DMA to the final host memory destination: @@ -31,9 +31,9 @@ destination: the TCP segments onto the wire. It handles TCP retransmission if needed. - On receving, S3 h/w recovers the iSCSI PDU by reassembling TCP + On receiving, S3 h/w recovers the iSCSI PDU by reassembling TCP segments, separating the header and data, calculating and verifying - the digests, then forwards the header to the host. The payload data, + the digests, then forwarding the header to the host. The payload data, if possible, will be directly placed into the pre-posted host DDP buffer. Otherwise, the payload data will be sent to the host too. @@ -68,9 +68,8 @@ The following steps need to be taken to accelerates the open-iscsi initiator: sure the ip address is unique in the network. 3. edit /etc/iscsi/iscsid.conf - The default setting for MaxRecvDataSegmentLength (131072) is too big, - replace "node.conn[0].iscsi.MaxRecvDataSegmentLength" to be a value no - bigger than 15360 (for example 8192): + The default setting for MaxRecvDataSegmentLength (131072) is too big; + replace with a value no bigger than 15360 (for example 8192): node.conn[0].iscsi.MaxRecvDataSegmentLength = 8192 -- cgit v1.2.1 From fe7ca2e1e847b65c12d245cbf402af89da96888a Mon Sep 17 00:00:00 2001 From: Brian Haley Date: Wed, 4 Mar 2009 03:18:11 -0800 Subject: IPv6: add "disable" module parameter support to ipv6.ko Add "disable" module parameter support to ipv6.ko by specifying "disable=1" on module load. We just do the minimum of initializing inetsw6[] so calls from other modules to inet6_register_protosw() won't OOPs, then bail out. No IPv6 addresses or sockets can be created as a result, and a reboot is required to enable IPv6. Signed-off-by: Brian Haley Signed-off-by: David S. Miller --- Documentation/networking/ipv6.txt | 35 +++++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+) create mode 100644 Documentation/networking/ipv6.txt (limited to 'Documentation') diff --git a/Documentation/networking/ipv6.txt b/Documentation/networking/ipv6.txt new file mode 100644 index 000000000000..268e5c103dd8 --- /dev/null +++ b/Documentation/networking/ipv6.txt @@ -0,0 +1,35 @@ + +Options for the ipv6 module are supplied as parameters at load time. + +Module options may be given as command line arguments to the insmod +or modprobe command, but are usually specified in either the +/etc/modules.conf or /etc/modprobe.conf configuration file, or in a +distro-specific configuration file. + +The available ipv6 module parameters are listed below. If a parameter +is not specified the default value is used. + +The parameters are as follows: + +disable + + Specifies whether to load the IPv6 module, but disable all + its functionality. This might be used when another module + has a dependency on the IPv6 module being loaded, but no + IPv6 addresses or operations are desired. + + The possible values and their effects are: + + 0 + IPv6 is enabled. + + This is the default value. + + 1 + IPv6 is disabled. + + No IPv6 addresses will be added to interfaces, and + it will not be possible to open an IPv6 socket. + + A reboot is required to enable IPv6. + -- cgit v1.2.1