From 1e1dea72651bff7bad8273d39c909ff8623cee6b Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Wed, 1 Jun 2016 00:23:22 +0800 Subject: ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators The AXP809 PMIC is the primary PMIC. It provides various supply voltages for the SoC and other peripherals. The PMIC's interrupt line is connected to NMI pin of the SoC. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 131 +++++++++++++++++++++++++++- 1 file changed, 129 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index eb2ccd0a3bd5..8d8af1189d87 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -98,7 +98,7 @@ &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; bus-width = <4>; cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */ cd-inverted; @@ -108,7 +108,7 @@ &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_pins>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -126,8 +126,135 @@ &r_rsb { status = "okay"; + + axp809: pmic@3a3 { + reg = <0x3a3>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + regulators { + reg_aldo1: aldo1 { + /* + * TODO: This should be handled by the + * USB PHY driver. + */ + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc33-usbh"; + }; + + reg_aldo2: aldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pb-io-cam"; + }; + + aldo3 { + /* unused */ + }; + + reg_dc5ldo: dc5ldo { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus-09-usbh"; + }; + + reg_dcdc1: dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v"; + }; + + reg_dcdc2: dcdc2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; + }; + + reg_dcdc3: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; + }; + + reg_dcdc4: dcdc4 { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys-usb0-hdmi"; + }; + + reg_dcdc5: dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1425000>; + regulator-max-microvolt = <1575000>; + regulator-name = "vcc-dram"; + }; + + reg_dldo1: dldo1 { + /* + * The WiFi chip supports a wide range + * (3.0 ~ 4.8V) of voltages, and so does + * this regulator (3.0 ~ 4.2V), but + * Allwinner SDK always sets it to 3.3V. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; + }; + + reg_dldo2: dldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pl"; + }; + + reg_eldo1: eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dvdd-cam"; + }; + + reg_eldo2: eldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pe"; + }; + + reg_eldo3: eldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pm-codec-io1"; + }; + + reg_ldo_io0: ldo_io0 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pg"; + }; + + reg_ldo_io1: ldo_io1 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-pa-gmac-2v5"; + }; + + reg_rtc_ldo: rtc_ldo { + regulator-name = "vcc-rtc-vdd1v8-io"; + }; + }; + }; }; +#include "axp809.dtsi" + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; -- cgit v1.2.1