# Configuration file for the Gigabyte GA-880GA-UD3H,
# contributed by Clipo.
# 2019-02-14 
# Updates welcome.
# 
# Based on Gigabyte GA-870A-UD3.conf contributed by Gary Myers and Zeke Fast
#
#
# CPU sensor

chip "k10temp-*"

   label temp1 "CPU Temp (K10)" 

# Motherboard sensors

chip "it8720-isa-*"

### Voltages

   label  in0  "Vcore"
   label  in1  "DDR3 1.5V" # as labelled in the BIOS.
   label  in2  "+3.3V"
   label  in3  "+5V"     # Not shown in BIOS.
   label  in4  "+12V"    # Not shown in BIOS
   ignore in5		 # Ambiguous - ignoring.
   ignore in6		 # Ambiguous - ignoring.
   label  in7  "5VSB"    # Not shown in BIOS.
   label  in8  "Vbat"    # Not shown in BIOS.
   ignore cpu0_vid

   # "Vcore", "DDR3 1.5V", "+3.3V" and "Vbat" are connected directly, so no compute
   # line is needed for these. +5V and 5VSB are internal so we use the
   # standard scaling factor. Scaling for +12V is apparently not standard
   # this value was taken from the donor config file
   # 
   compute  in3  @ * (6.8/10+1), @ / (6.8/10+1)
   compute  in4  @ * 3.963,      @ / 3.963
   compute  in7  @ * (6.8/10+1), @ / (6.8/10+1)

   # The BIOS will not set any limit for voltages.

   set in0_min  0.825 * 0.95
   set in0_max  1.425 * 1.05
   set in1_min  1.5   * 0.95
   set in1_max  1.5   * 1.05
   set in2_min  3.3   * 0.95
   set in2_max  3.3   * 1.05
   set in3_min  5     * 0.95
   set in3_max  5     * 1.05
   set in4_min 12     * 0.95
   set in4_max 12     * 1.05
   set in7_min  5     * 0.95
   set in7_max  5     * 1.05

### Temperatures

   label temp1 "System Temp"
   # This sensor appears to be around or inside the ITE8720F chip.
   set   temp1_min 0
   set   temp1_max 40 

   label temp2  "CPU Temp"
   # This sensor can show 2 degrees difference to the K10 sensor.
   # The end user can choose which one they prefer.
   set   temp2_min 0
   set   temp2_max 60 # Set to match your BIOS "CPU Warning Temperature"

   label temp3 "Second CPU Temp?"
   #This sensors appears to follow the CPU temp but with a large termal lag and slightly lower value
   #
   #set   temp3	# 

### Fans

   # Label based on motherboard connectors.
   label fan1 "CPU Fan"		# M/B label: CPU_FAN (4-pin)
   label fan5 "Power Fan"	# M/B label: PWR_FAN (3-pin)
   label fan2 "System Fan 1"	# M/B label: SYS_FAN1 (3-pin)
   label fan3 "System Fan 2"	# M/B label: SYS_FAN2 (3-pin)

   # Minimum fan speeds.
   # Comment/un-comment fan headers you are using if you want alarms.
   set fan1_min 300	# CPU Fan
   set fan5_min 300	# Power Fan
   set fan2_min 300	# System Fan 1
   set fan3_min 300     # System Fan 2

# Original Sensors output before configuration applied
#
## it8720-isa-0228
#Adapter: ISA adapter
#in0:          +1.46 V  (min =  +0.00 V, max =  +4.08 V)
#in1:          +1.49 V  (min =  +0.00 V, max =  +4.08 V)
#in2:          +3.38 V  (min =  +0.00 V, max =  +4.08 V)
#+5V:          +3.02 V  (min =  +0.00 V, max =  +4.08 V)
#in4:          +3.09 V  (min =  +0.00 V, max =  +4.08 V)
#in5:          +2.85 V  (min =  +0.00 V, max =  +4.08 V)
#in6:          +4.08 V  (min =  +0.00 V, max =  +4.08 V)
#5VSB:         +2.96 V  (min =  +0.00 V, max =  +4.08 V)
#Vbat:         +3.02 V
#fan1:         629 RPM  (min =   10 RPM)
#fan2:         950 RPM  (min =   10 RPM)
#fan3:        1315 RPM  (min =   10 RPM)
#fan5:        1310 RPM  (min =   10 RPM)
#temp1:        +26.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
#temp2:        +32.0°C  (low  = +127.0°C, high = +60.0°C)  sensor = thermal diode
#temp3:        +34.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
#cpu0_vid:    +0.513 V
#intrusion0:  ALARM
#
#k10temp-pci-00c3
#Adapter: PCI adapter
#temp1:        +32.9°C  (high = +70.0°C)
#                       (crit = +79.0°C, hyst = +77.0°C)