| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
| |
This simplifies the cookie handling a bit.
Signed-off-by: Justin Pettit <jpettit@ovn.org>
Acked-by: Ben Pfaff <blp@ovn.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Extend flow key part of data record to include following Information Elements:
- ingressInterface
- ingressInterfaceType
- egressInterface
- egressInterfaceType
- interfaceName
- interfaceDescription
In case of input sampling we don't have information about egress port.
Define templates depending not only on protocol types, but also on flow
direction. Only egress flow will include egress information elements.
With this change, dpif_ipfix_exporter stores every port in hmap rather
than only tunnel ports. It allows to easily retrieve required
information about interfaces during sampling upcalls.
Co-authored-by: Michal Weglicki <michalx.weglicki@intel.com>
Signed-off-by: Michal Weglicki <michalx.weglicki@intel.com>
Signed-off-by: Przemyslaw Szczerbik <przemyslawx.szczerbik@intel.com>
Signed-off-by: Ben Pfaff <blp@ovn.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Patch based on RFC 5102, section 5.10. It implements per-flow drop counters:
- droppedPacketDeltaCount
- droppedPacketTotalCount
- droppedOctetDeltaCount
- droppedOctetTotalCount
In order to determine if packet is going to be dropped, flow actions associated
with packet are read. If at least one of the following conditions is met,
packet is not marked as dropped.
Packet has at least one:
- OVS_ACTION_ATTR_OUTPUT action
- OVS_ACTION_ATTR_CLONE action with nested OVS_ACTION_ATTR_OUTPUT action
- OVS_ACTION_ATTR_SAMPLE action with nested OVS_ACTION_ATTR_OUTPUT action and
sampling probability is set to 100%
Signed-off-by: Przemyslaw Szczerbik <przemyslawx.szczerbik@intel.com>
Signed-off-by: Ben Pfaff <blp@ovn.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support to export tunnel information for flow-based IPFIX.
The original steps to configure flow level IPFIX:
1) Create a new record in Flow_Sample_Collector_Set table:
'ovs-vsctl -- create Flow_Sample_Collector_Set id=1 bridge="Bridge UUID"'
2) Add IPFIX configuration which is referred by corresponding
row in Flow_Sample_Collector_Set table:
'ovs-vsctl -- set Flow_Sample_Collector_Set
"Flow_Sample_Collector_Set UUID" ipfix=@i -- --id=@i create IPFIX
targets=\"IP:4739\" obs_domain_id=123 obs_point_id=456
cache_active_timeout=60 cache_max_flows=13'
3) Add sample action to the flows:
'ovs-ofctl add-flow mybridge in_port=1,
actions=sample'('probability=65535,collector_set_id=1,
obs_domain_id=123,obs_point_id=456')',output:3'
NXAST_SAMPLE action was used in step 3. In order to support exporting tunnel
information, the NXAST_SAMPLE2 action was added and with NXAST_SAMPLE2 action
in this patch, the step 3 should be configured like below:
'ovs-ofctl add-flow mybridge in_port=1,
actions=sample'('probability=65535,collector_set_id=1,obs_domain_id=123,
obs_point_id=456,sampling_port=3')',output:3'
'sampling_port' can be equal to ingress port or one of egress ports. If sampling
port is equal to output port and the output port is a tunnel port,
OVS_USERSPACE_ATTR_EGRESS_TUN_PORT will be set in the datapath flow sample action.
When flow sample action upcall happens, tunnel information will be retrieved from
the datapath and then IPFIX can export egress tunnel port information. If
samping_port=65535 (OFPP_NONE), flow-based IPFIX will keep the same behavior
as before.
This patch mainly do three tasks:
1) Add a new flow sample action NXAST_SAMPLE2 to support exporting
tunnel information. NXAST_SAMPLE2 action has a new added field
'sampling_port'.
2) Use 'other_configure: enable-tunnel-sampling' to enable or disable
exporting tunnel information.
3) If 'sampling_port' is equal to output port and output port is a tunnel
port, the translation of OpenFlow "sample" action should first emit
set(tunnel(...)), then the sample action itself. It makes sure the
egress tunnel information can be sampled.
4) Add a test of flow-based IPFIX for tunnel set.
How to test flow-based IPFIX:
1) Setup a test environment with two Linux host with Docker supported
2) Create a Docker container and a GRE tunnel port on each host
3) Use ovs-docker to add the container on the bridge
4) Listen on port 4739 on the collector machine and use wireshark to filter
'cflow' packets.
5) Configure flow-based IPFIX:
- 'ovs-vsctl -- create Flow_Sample_Collector_Set id=1 bridge="Bridge UUID"'
- 'ovs-vsctl -- set Flow_Sample_Collector_Set
"Flow_Sample_Collector_Set UUID" ipfix=@i -- --id=@i create IPFIX \
targets=\"IP:4739\" cache_active_timeout=60 cache_max_flows=13 \
other_config:enable-tunnel-sampling=true'
- 'ovs-ofctl add-flow mybridge in_port=1,
actions=sample'('probability=65535,collector_set_id=1,obs_domain_id=123,
obs_point_id=456,sampling_port=3')',output:3'
Note: The in-port is container port. The output port and sampling_port
are both open flow port and the output port is a GRE tunnel port.
6) Ping from the container whose host enabled flow-based IPFIX.
7) Get the IPFIX template pakcets and IPFIX information packets.
Signed-off-by: Benli Ye <daniely@vmware.com>
Signed-off-by: Ben Pfaff <blp@ovn.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
It is meaningful for user to check the stats of IPFIX.
Using IPFIX stats, user can know how much flows the system
can support. It is also can be used for performance check
of IPFIX.
IPFIX stats is added for per IPFIX exporter. If bridge IPFIX is
enabled on the bridge, the whole bridge will have one exporter.
For flow IPFIX, the system keeps per id (column in
Flow_Sample_Collector_Set) per exporter.
1) Add 'ovs-ofctl dump-ipfix-bridge SWITCH' to export IPFIX stats of
the bridge which enable bridge IPFIX. The output format:
NXST_IPFIX_BRIDGE reply (xid=0x2):
bridge ipfix: flows=0, current flows=0, sampled pkts=0, \
ipv4 ok=0, ipv6 ok=0, tx pkts=0
pkts errs=0, ipv4 errs=0, ipv6 errs=0, tx errs=0
2) Add 'ovs-ofctl dump-ipfix-flow SWITCH' to export IPFIX stats of
the bridge which enable flow IPFIX. The output format:
NXST_IPFIX_FLOW reply (xid=0x2): 2 ids
id 1: flows=4, current flows=4, sampled pkts=14, ipv4 ok=13, \
ipv6 ok=0, tx pkts=0
pkts errs=0, ipv4 errs=0, ipv6 errs=0, tx errs=0
id 2: flows=0, current flows=0, sampled pkts=0, ipv4 ok=0, \
ipv6 ok=0, tx pkts=0
pkts errs=0, ipv4 errs=0, ipv6 errs=0, tx errs=0
flows: the number of total flow records, including those exported.
current flows: the number of current flow records cached.
sampled pkts: Successfully sampled packet count.
ipv4 ok: successfully sampled IPv4 flow packet count.
ipv6 ok: Successfully sampled IPv6 flow packet count.
tx pkts: the count of IPFIX exported packets sent to the collector(s).
pkts errs: count of packets failed when sampling, maybe not supported or other error.
ipv4 errs: Count of IPV4 flow packet in the error packets.
ipv6 errs: Count of IPV6 flow packet in the error packets.
tx errs: the count of IPFIX exported packets failed when sending to the collector(s).
Signed-off-by: Benli Ye <daniely@vmware.com>
Signed-off-by: Ben Pfaff <blp@ovn.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Currently dp-packet make use of ofpbuf for managing packet
buffers. That complicates ofpbuf, by making dp-packet
independent of ofpbuf both libraries can be optimized for
their own use case.
This avoids mapping operation between ofpbuf and dp_packet
in datapath upcalls.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Ben Pfaff <blp@nicira.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Extend IPFIX exporter to export tunnel headers when both input and output
of the port.
Add three other_config options in IPFIX table: enable-input-sampling,
enable-output-sampling and enable-tunnel-sampling, to control whether
sampling tunnel info, on which direction (input or output).
Insert sampling action before output action and the output tunnel port
is sent to datapath in the sampling action.
Make datapath collect output tunnel info and send it back to userpace
in upcall message with a new additional optional attribute.
Add a tunnel ports map to make the tunnel port lookup faster in sampling
upcalls in IPFIX exporter. Make the IPFIX exporter generate IPFIX template
sets with enterprise elements for the tunnel info, save the tunnel info
in IPFIX cache entries, and send IPFIX DATA with tunnel info.
Add flowDirection element in IPFIX templates.
Signed-off-by: Wenyu Zhang <wenyuz@vmware.com>
Acked-by: Romain Lenglet <rlenglet@vmware.com>
Acked-by: Ben Pfaff <blp@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
This patch reorganizes ofproto-dpif in preparation for future patches
which allow direct upcall processing from dpif-netdev. The main goals
are to share as much code as possible between the dpif-linux and
dpif-netdev upcall paths. Additionally, to avoid confusing the
dpif-netdev fast path, the packet processing path should treat packets
and struct flow's as const.
Signed-off-by: Ethan Jackson <ethan@nicira.com>
Acked-by: Ben Pfaff <blp@nicira.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Implement a per-exporter flow cache with active timeout expiration.
Add columns "cache_active_timeout" and "cache_max_flows" into table
"IPFIX" to configure each cache.
Add per-flow elements "octetDeltaSumOfSquares",
"minimumIpTotalLength", and "maximumIpTotalLength" to replace
"ethernetTotalLength". Add per-flow element "flowEndReason" to
indicate whether a flow has expired because of an active timeout, the
cache size limit being reached, or the exporter being stopped.
Signed-off-by: Romain Lenglet <rlenglet@vmware.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
|
| |
|
|
|
| |
Signed-off-by: Ethan Jackson <ethan@nicira.com>
Acked-by: Ben Pfaff <blp@nicira.com>
|
|
|
Define a new NXAST_SAMPLE OpenFlow vendor action and the corresponding
OFPACT_SAMPLE OVS action, to do per-flow packet sampling, translated
into a new SAMPLE "flow_sample" dp action.
Make the userspace action's userdata size vary depending on the union
member used. Add a new "flow_sample" upcall to do per-flow packet
sampling. Add a new "ipfix" upcall to do per-bridge packet sampling
to IPFIX collectors.
Extend the OVSDB schema to support configuring IPFIX collector sets.
Add support for configuring multiple IPFIX collectors for per-flow
packet sampling. Add support for configuring per-bridge IPFIX
sampling.
Automatically generate standard IPFIX entity definitions from the IANA
specs. Send one IPFIX data record message for every packet sampled by
an OpenFlow sample action or received by a bridge configured with
IPFIX sampling, and periodically send IPFIX template set messages.
Signed-off-by: Romain Lenglet <rlenglet@vmware.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
|
