A database with this schema holds the configuration for one Open vSwitch daemon. The top-level configuration for the daemon is the table, which must have exactly one record. Records in other tables are significant only when they can be reached directly or indirectly from the table. Records that are not reachable from the table are automatically deleted from the database, except for records in a few distinguished ``root set'' tables.

Common Columns

Most tables contain two special columns, named other_config and external_ids. These columns have the same form and purpose each place that they appear, so we describe them here to save space later.

other_config: map of string-string pairs

Key-value pairs for configuring rarely used features. Supported keys, along with the forms taken by their values, are documented individually for each table.

A few tables do not have other_config columns because no key-value pairs have yet been defined for them.

external_ids: map of string-string pairs
Key-value pairs for use by external frameworks that integrate with Open vSwitch, rather than by Open vSwitch itself. System integrators should either use the Open vSwitch development mailing list to coordinate on common key-value definitions, or choose key names that are likely to be unique. In some cases, where key-value pairs have been defined that are likely to be widely useful, they are documented individually for each table.
Configuration for an Open vSwitch daemon. There must be exactly one record in the table. Set of bridges managed by the daemon. SSL used globally by the daemon. A unique identifier for the Open vSwitch's physical host. The form of the identifier depends on the type of the host. On a Citrix XenServer, this will likely be the same as . The Citrix XenServer universally unique identifier for the physical host as displayed by xe host-list.

Interval for updating statistics to the database, in milliseconds. This option will affect the update of the statistics column in the following tables: Port, Interface , Mirror.

Default value is 5000 ms.

Getting statistics more frequently can be achieved via OpenFlow.

When ovs-vswitchd starts up, it has an empty flow table and therefore it handles all arriving packets in its default fashion according to its configuration, by dropping them or sending them to an OpenFlow controller or switching them as a standalone switch. This behavior is ordinarily desirable. However, if ovs-vswitchd is restarting as part of a ``hot-upgrade,'' then this leads to a relatively long period during which packets are mishandled.

This option allows for improvement. When ovs-vswitchd starts with this value set as true, it will neither flush or expire previously set datapath flows nor will it send and receive any packets to or from the datapath. When this value is later set to false, ovs-vswitchd will start receiving packets from the datapath and re-setup the flows.

Thus, with this option, the procedure for a hot-upgrade of ovs-vswitchd becomes roughly the following:

  1. Stop ovs-vswitchd.
  2. Set to true.
  3. Start ovs-vswitchd.
  4. Use ovs-ofctl (or some other program, such as an OpenFlow controller) to restore the OpenFlow flow table to the desired state.
  5. Set to false (or remove it entirely from the database).

The ovs-ctl's ``restart'' and ``force-reload-kmod'' functions use the above config option during hot upgrades.

The maximum number of flows allowed in the datapath flow table. Internally OVS will choose a flow limit which will likely be lower than this number, based on real time network conditions.

The default is 200000.

Specifies the number of rx queues to be created for each dpdk interface. If not specified or specified to 0, one rx queue will be created for each dpdk interface by default.

Specifies CPU mask for setting the cpu affinity of PMD (Poll Mode Driver) threads. Value should be in the form of hex string, similar to the dpdk EAL '-c COREMASK' option input or the 'taskset' mask input.

The lowest order bit corresponds to the first CPU core. A set bit means the corresponding core is available and a pmd thread will be created and pinned to it. If the input does not cover all cores, those uncovered cores are considered not set.

If not specified, one pmd thread will be created for each numa node and pinned to any available core on the numa node by default.

Specifies the number of threads for software datapaths to use for handling new flows. The default the number of online CPU cores minus the number of revalidators.

This configuration is per datapath. If you have more than one software datapath (e.g. some system bridges and some netdev bridges), then the total number of threads is n-handler-threads times the number of software datapaths.

Specifies the number of threads for software datapaths to use for revalidating flows in the datapath. Typically, there is a direct correlation between the number of revalidator threads, and the number of flows allowed in the datapath. The default is the number of cpu cores divided by four plus one. If n-handler-threads is set, the default changes to the number of cpu cores minus the number of handler threads.

This configuration is per datapath. If you have more than one software datapath (e.g. some system bridges and some netdev bridges), then the total number of threads is n-handler-threads times the number of software datapaths.

Sequence number for client to increment. When a client modifies any part of the database configuration and wishes to wait for Open vSwitch to finish applying the changes, it may increment this sequence number. Sequence number that Open vSwitch sets to the current value of after it finishes applying a set of configuration changes.

The statistics column contains key-value pairs that report statistics about a system running an Open vSwitch. These are updated periodically (currently, every 5 seconds). Key-value pairs that cannot be determined or that do not apply to a platform are omitted.

Statistics are disabled by default to avoid overhead in the common case when statistics gathering is not useful. Set this value to true to enable populating the column or to false to explicitly disable it.

Number of CPU processors, threads, or cores currently online and available to the operating system on which Open vSwitch is running, as an integer. This may be less than the number installed, if some are not online or if they are not available to the operating system.

Open vSwitch userspace processes are not multithreaded, but the Linux kernel-based datapath is.

A comma-separated list of three floating-point numbers, representing the system load average over the last 1, 5, and 15 minutes, respectively.

A comma-separated list of integers, each of which represents a quantity of memory in kilobytes that describes the operating system on which Open vSwitch is running. In respective order, these values are:

  1. Total amount of RAM allocated to the OS.
  2. RAM allocated to the OS that is in use.
  3. RAM that can be flushed out to disk or otherwise discarded if that space is needed for another purpose. This number is necessarily less than or equal to the previous value.
  4. Total disk space allocated for swap.
  5. Swap space currently in use.

On Linux, all five values can be determined and are included. On other operating systems, only the first two values can be determined, so the list will only have two values.

One such key-value pair, with NAME replaced by a process name, will exist for each running Open vSwitch daemon process, with name replaced by the daemon's name (e.g. process_ovs-vswitchd). The value is a comma-separated list of integers. The integers represent the following, with memory measured in kilobytes and durations in milliseconds:

  1. The process's virtual memory size.
  2. The process's resident set size.
  3. The amount of user and system CPU time consumed by the process.
  4. The number of times that the process has crashed and been automatically restarted by the monitor.
  5. The duration since the process was started.
  6. The duration for which the process has been running.

The interpretation of some of these values depends on whether the process was started with the . If it was not, then the crash count will always be 0 and the two durations will always be the same. If was given, then the crash count may be positive; if it is, the latter duration is the amount of time since the most recent crash and restart.

There will be one key-value pair for each file in Open vSwitch's ``run directory'' (usually /var/run/openvswitch) whose name ends in .pid, whose contents are a process ID, and which is locked by a running process. The name is taken from the pidfile's name.

Currently Open vSwitch is only able to obtain all of the above detail on Linux systems. On other systems, the same key-value pairs will be present but the values will always be the empty string.

A space-separated list of information on local, writable file systems. Each item in the list describes one file system and consists in turn of a comma-separated list of the following:

  1. Mount point, e.g. / or /var/log. Any spaces or commas in the mount point are replaced by underscores.
  2. Total size, in kilobytes, as an integer.
  3. Amount of storage in use, in kilobytes, as an integer.

This key-value pair is omitted if there are no local, writable file systems or if Open vSwitch cannot obtain the needed information.

These columns report the types and versions of the hardware and software running Open vSwitch. We recommend in general that software should test whether specific features are supported instead of relying on version number checks. These values are primarily intended for reporting to human administrators.

The Open vSwitch version number, e.g. 1.1.0.

The database schema version number in the form major.minor.tweak, e.g. 1.2.3. Whenever the database schema is changed in a non-backward compatible way (e.g. deleting a column or a table), major is incremented. When the database schema is changed in a backward compatible way (e.g. adding a new column), minor is incremented. When the database schema is changed cosmetically (e.g. reindenting its syntax), tweak is incremented.

The schema version is part of the database schema, so it can also be retrieved by fetching the schema using the Open vSwitch database protocol.

An identifier for the type of system on top of which Open vSwitch runs, e.g. XenServer or KVM.

System integrators are responsible for choosing and setting an appropriate value for this column.

The version of the system identified by , e.g. 5.6.100-39265p on XenServer 5.6.100 build 39265.

System integrators are responsible for choosing and setting an appropriate value for this column.

These columns report capabilities of the Open vSwitch instance.

This column reports the different dpifs registered with the system. These are the values that this instance supports in the column of the table.

This column reports the different netdevs registered with the system. These are the values that this instance supports in the column of the table.

These columns primarily configure the Open vSwitch database (ovsdb-server), not the Open vSwitch switch (ovs-vswitchd). The OVSDB database also uses the settings.

The Open vSwitch switch does read the database configuration to determine remote IP addresses to which in-band control should apply.

Database clients to which the Open vSwitch database server should connect or to which it should listen, along with options for how these connection should be configured. See the table for more information.
The overall purpose of these columns is described under Common Columns at the beginning of this document.

Configuration for a bridge within an .

A record represents an Ethernet switch with one or more ``ports,'' which are the records pointed to by the 's column.

Bridge identifier. Should be alphanumeric and no more than about 8 bytes long. Must be unique among the names of ports, interfaces, and bridges on a host. Ports included in the bridge. Port mirroring configuration. NetFlow configuration. sFlow(R) configuration. IPFIX configuration.

VLAN IDs of VLANs on which MAC address learning should be disabled, so that packets are flooded instead of being sent to specific ports that are believed to contain packets' destination MACs. This should ordinarily be used to disable MAC learning on VLANs used for mirroring (RSPAN VLANs). It may also be useful for debugging.

SLB bonding (see the column in the table) is incompatible with flood_vlans. Consider using another bonding mode or a different type of mirror instead.

Auto Attach configuration.

OpenFlow controller set. If unset, then no OpenFlow controllers will be used.

If there are primary controllers, removing all of them clears the flow table. If there are no primary controllers, adding one also clears the flow table. Other changes to the set of controllers, such as adding or removing a service controller, adding another primary controller to supplement an existing primary controller, or removing only one of two primary controllers, have no effect on the flow table.

Configuration for OpenFlow tables. Each pair maps from an OpenFlow table ID to configuration for that table.

When a controller is configured, it is, ordinarily, responsible for setting up all flows on the switch. Thus, if the connection to the controller fails, no new network connections can be set up. If the connection to the controller stays down long enough, no packets can pass through the switch at all. This setting determines the switch's response to such a situation. It may be set to one of the following:

standalone
If no message is received from the controller for three times the inactivity probe interval (see ), then Open vSwitch will take over responsibility for setting up flows. In this mode, Open vSwitch causes the bridge to act like an ordinary MAC-learning switch. Open vSwitch will continue to retry connecting to the controller in the background and, when the connection succeeds, it will discontinue its standalone behavior.
secure
Open vSwitch will not set up flows on its own when the controller connection fails or when no controllers are defined. The bridge will continue to retry connecting to any defined controllers forever.

The default is standalone if the value is unset, but future versions of Open vSwitch may change the default.

The standalone mode can create forwarding loops on a bridge that has more than one uplink port unless STP is enabled. To avoid loops on such a bridge, configure secure mode or enable STP (see ).

When more than one controller is configured, is considered only when none of the configured controllers can be contacted.

Changing when no primary controllers are configured clears the flow table.

Reports the OpenFlow datapath ID in use. Exactly 16 hex digits. (Setting this column has no useful effect. Set instead.)

Reports the version number of the Open vSwitch datapath in use. This allows management software to detect and report discrepancies between Open vSwitch userspace and datapath versions. (The column in the reports the Open vSwitch userspace version.) The version reported depends on the datapath in use:

  • When the kernel module included in the Open vSwitch source tree is used, this column reports the Open vSwitch version from which the module was taken.
  • When the kernel module that is part of the upstream Linux kernel is used, this column reports <unknown>.
  • When the datapath is built into the ovs-vswitchd binary, this column reports <built-in>. A built-in datapath is by definition the same version as the rest of the Open VSwitch userspace.
  • Other datapaths (such as the Hyper-V kernel datapath) currently report <unknown>.

A version discrepancy between ovs-vswitchd and the datapath in use is not normally cause for alarm. The Open vSwitch kernel datapaths for Linux and Hyper-V, in particular, are designed for maximum inter-version compatibility: any userspace version works with with any kernel version. Some reasons do exist to insist on particular user/kernel pairings. First, newer kernel versions add new features, that can only be used by new-enough userspace, e.g. VXLAN tunneling requires certain minimal userspace and kernel versions. Second, as an extension to the first reason, some newer kernel versions add new features for enhancing performance that only new-enough userspace versions can take advantage of.

Exactly 16 hex digits to set the OpenFlow datapath ID to a specific value. May not be all-zero. Human readable description of datapath. It it a maximum 256 byte-long free-form string to describe the datapath for debugging purposes, e.g. switch3 in room 3120. If set to true, disable in-band control on the bridge regardless of controller and manager settings. A queue ID as a nonnegative integer. This sets the OpenFlow queue ID that will be used by flows set up by in-band control on this bridge. If unset, or if the port used by an in-band control flow does not have QoS configured, or if the port does not have a queue with the specified ID, the default queue is used instead.

List of OpenFlow protocols that may be used when negotiating a connection with a controller. OpenFlow 1.0, 1.1, 1.2, and 1.3 are enabled by default if this column is empty.

OpenFlow 1.4 is not enabled by default because its implementation is missing features.

OpenFlow 1.5 has the same risks as OpenFlow 1.4, but it is even more experimental because the OpenFlow 1.5 specification is still under development and thus subject to change. Pass --enable-of15 to ovs-vswitchd to allow OpenFlow 1.5 to be enabled.

The IEEE 802.1D Spanning Tree Protocol (STP) is a network protocol that ensures loop-free topologies. It allows redundant links to be included in the network to provide automatic backup paths if the active links fails.

These settings configure the slower-to-converge but still widely supported version of Spanning Tree Protocol, sometimes known as 802.1D-1998. Open vSwitch also supports the newer Rapid Spanning Tree Protocol (RSTP), documented later in the section titled Rapid Spanning Tree Configuration.

Enable spanning tree on the bridge. By default, STP is disabled on bridges. Bond, internal, and mirror ports are not supported and will not participate in the spanning tree.

STP and RSTP are mutually exclusive. If both are enabled, RSTP will be used.

The bridge's STP identifier (the lower 48 bits of the bridge-id) in the form xx:xx:xx:xx:xx:xx. By default, the identifier is the MAC address of the bridge. The bridge's relative priority value for determining the root bridge (the upper 16 bits of the bridge-id). A bridge with the lowest bridge-id is elected the root. By default, the priority is 0x8000. The interval between transmissions of hello messages by designated ports, in seconds. By default the hello interval is 2 seconds. The maximum age of the information transmitted by the bridge when it is the root bridge, in seconds. By default, the maximum age is 20 seconds. The delay to wait between transitioning root and designated ports to forwarding, in seconds. By default, the forwarding delay is 15 seconds.

The maximum number of seconds to retain a multicast snooping entry for which no packets have been seen. The default is currently 300 seconds (5 minutes). The value, if specified, is forced into a reasonable range, currently 15 to 3600 seconds.

The maximum number of multicast snooping addresses to learn. The default is currently 2048. The value, if specified, is forced into a reasonable range, currently 10 to 1,000,000.

If set to false, unregistered multicast packets are forwarded to all ports. If set to true, unregistered multicast packets are forwarded to ports connected to multicast routers.

These key-value pairs report the status of 802.1D-1998. They are present only if STP is enabled (via the column).

The bridge ID used in spanning tree advertisements, in the form xxxx.yyyyyyyyyyyy where the xs are the STP priority, the ys are the STP system ID, and each x and y is a hex digit. The designated root for this spanning tree, in the same form as . If this bridge is the root, this will have the same value as , otherwise it will differ. The path cost of reaching the designated bridge. A lower number is better. The value is 0 if this bridge is the root, otherwise it is higher.

Rapid Spanning Tree Protocol (RSTP), like STP, is a network protocol that ensures loop-free topologies. RSTP superseded STP with the publication of 802.1D-2004. Compared to STP, RSTP converges more quickly and recovers more quickly from failures.

Enable Rapid Spanning Tree on the bridge. By default, RSTP is disabled on bridges. Bond, internal, and mirror ports are not supported and will not participate in the spanning tree.

STP and RSTP are mutually exclusive. If both are enabled, RSTP will be used.

The bridge's RSTP address (the lower 48 bits of the bridge-id) in the form xx:xx:xx:xx:xx:xx. By default, the address is the MAC address of the bridge. The bridge's relative priority value for determining the root bridge (the upper 16 bits of the bridge-id). A bridge with the lowest bridge-id is elected the root. By default, the priority is 0x8000 (32768). This value needs to be a multiple of 4096, otherwise it's rounded to the nearest inferior one. The Ageing Time parameter for the Bridge. The default value is 300 seconds. The Force Protocol Version parameter for the Bridge. This can take the value 0 (STP Compatibility mode) or 2 (the default, normal operation). The maximum age of the information transmitted by the Bridge when it is the Root Bridge. The default value is 20. The delay used by STP Bridges to transition Root and Designated Ports to Forwarding. The default value is 15. The Transmit Hold Count used by the Port Transmit state machine to limit transmission rate. The default value is 6.

These key-value pairs report the status of 802.1D-2004. They are present only if RSTP is enabled (via the column).

The bridge ID used in rapid spanning tree advertisements, in the form x.yyy.zzzzzzzzzzzz where x is the RSTP priority, the ys are a locally assigned system ID extension, the zs are the STP system ID, and each x, y, or z is a hex digit. The root of this spanning tree, in the same form as . If this bridge is the root, this will have the same value as , otherwise it will differ. The path cost of reaching the root. A lower number is better. The value is 0 if this bridge is the root, otherwise it is higher. The RSTP designated ID, in the same form as . The RSTP designated port ID, as a 4-digit hex number. The RSTP bridge port ID, as a 4-digit hex number.
Multicast snooping (RFC 4541) monitors the Internet Group Management Protocol (IGMP) traffic between hosts and multicast routers. The switch uses what IGMP snooping learns to forward multicast traffic only to interfaces that are connected to interested receivers. Currently it supports IGMPv1 and IGMPv2 protocols. Enable multicast snooping on the bridge. For now, the default is disabled. Name of datapath provider. The kernel datapath has type system. The userspace datapath has type netdev. A manager may refer to the column of the table for a list of the types accepted by this Open vSwitch instance. A unique identifier of the bridge. On Citrix XenServer this will commonly be the same as . Semicolon-delimited set of universally unique identifier(s) for the network with which this bridge is associated on a Citrix XenServer host. The network identifiers are RFC 4122 UUIDs as displayed by, e.g., xe network-list. An Ethernet address in the form xx:xx:xx:xx:xx:xx to set the hardware address of the local port and influence the datapath ID.

Controls forwarding of BPDUs and other network control frames when NORMAL action is invoked. When this option is false or unset, frames with reserved Ethernet addresses (see table below) will not be forwarded. When this option is true, such frames will not be treated specially.

The above general rule has the following exceptions:

  • If STP is enabled on the bridge (see the column in the table), the bridge processes all received STP packets and never passes them to OpenFlow or forwards them. This is true even if STP is disabled on an individual port.
  • If LLDP is enabled on an interface (see the column in the table), the interface processes received LLDP packets and never passes them to OpenFlow or forwards them.

Set this option to true if the Open vSwitch bridge connects different Ethernet networks and is not configured to participate in STP.

This option affects packets with the following destination MAC addresses:

01:80:c2:00:00:00
IEEE 802.1D Spanning Tree Protocol (STP).
01:80:c2:00:00:01
IEEE Pause frame.
01:80:c2:00:00:0x
Other reserved protocols.
00:e0:2b:00:00:00
Extreme Discovery Protocol (EDP).
00:e0:2b:00:00:04 and 00:e0:2b:00:00:06
Ethernet Automatic Protection Switching (EAPS).
01:00:0c:cc:cc:cc
Cisco Discovery Protocol (CDP), VLAN Trunking Protocol (VTP), Dynamic Trunking Protocol (DTP), Port Aggregation Protocol (PAgP), and others.
01:00:0c:cc:cc:cd
Cisco Shared Spanning Tree Protocol PVSTP+.
01:00:0c:cd:cd:cd
Cisco STP Uplink Fast.
01:00:0c:00:00:00
Cisco Inter Switch Link.
01:00:0c:cc:cc:cx
Cisco CFM.

The maximum number of seconds to retain a MAC learning entry for which no packets have been seen. The default is currently 300 seconds (5 minutes). The value, if specified, is forced into a reasonable range, currently 15 to 3600 seconds.

A short MAC aging time allows a network to more quickly detect that a host is no longer connected to a switch port. However, it also makes it more likely that packets will be flooded unnecessarily, when they are addressed to a connected host that rarely transmits packets. To reduce the incidence of unnecessary flooding, use a MAC aging time longer than the maximum interval at which a host will ordinarily transmit packets.

The maximum number of MAC addresses to learn. The default is currently 2048. The value, if specified, is forced into a reasonable range, currently 10 to 1,000,000.

The overall purpose of these columns is described under Common Columns at the beginning of this document.

A port within a .

Most commonly, a port has exactly one ``interface,'' pointed to by its column. Such a port logically corresponds to a port on a physical Ethernet switch. A port with more than one interface is a ``bonded port'' (see ).

Some properties that one might think as belonging to a port are actually part of the port's members.

Port name. Should be alphanumeric and no more than about 8 bytes long. May be the same as the interface name, for non-bonded ports. Must otherwise be unique among the names of ports, interfaces, and bridges on a host. The port's interfaces. If there is more than one, this is a bonded Port.

Bridge ports support the following types of VLAN configuration:

trunk

A trunk port carries packets on one or more specified VLANs specified in the column (often, on every VLAN). A packet that ingresses on a trunk port is in the VLAN specified in its 802.1Q header, or VLAN 0 if the packet has no 802.1Q header. A packet that egresses through a trunk port will have an 802.1Q header if it has a nonzero VLAN ID.

Any packet that ingresses on a trunk port tagged with a VLAN that the port does not trunk is dropped.

access

An access port carries packets on exactly one VLAN specified in the column. Packets egressing on an access port have no 802.1Q header.

Any packet with an 802.1Q header with a nonzero VLAN ID that ingresses on an access port is dropped, regardless of whether the VLAN ID in the header is the access port's VLAN ID.

native-tagged
A native-tagged port resembles a trunk port, with the exception that a packet without an 802.1Q header that ingresses on a native-tagged port is in the ``native VLAN'' (specified in the column).
native-untagged
A native-untagged port resembles a native-tagged port, with the exception that a packet that egresses on a native-untagged port in the native VLAN will not have an 802.1Q header.

A packet will only egress through bridge ports that carry the VLAN of the packet, as described by the rules above.

The VLAN mode of the port, as described above. When this column is empty, a default mode is selected as follows:

  • If contains a value, the port is an access port. The column should be empty.
  • Otherwise, the port is a trunk port. The column value is honored if it is present.

For an access port, the port's implicitly tagged VLAN. For a native-tagged or native-untagged port, the port's native VLAN. Must be empty if this is a trunk port.

For a trunk, native-tagged, or native-untagged port, the 802.1Q VLAN or VLANs that this port trunks; if it is empty, then the port trunks all VLANs. Must be empty if this is an access port.

A native-tagged or native-untagged port always trunks its native VLAN, regardless of whether includes that VLAN.

An 802.1Q header contains two important pieces of information: a VLAN ID and a priority. A frame with a zero VLAN ID, called a ``priority-tagged'' frame, is supposed to be treated the same way as a frame without an 802.1Q header at all (except for the priority).

However, some network elements ignore any frame that has 802.1Q header at all, even when the VLAN ID is zero. Therefore, by default Open vSwitch does not output priority-tagged frames, instead omitting the 802.1Q header entirely if the VLAN ID is zero. Set this key to true to enable priority-tagged frames on a port.

Regardless of this setting, Open vSwitch omits the 802.1Q header on output if both the VLAN ID and priority would be zero.

All frames output to native-tagged ports have a nonzero VLAN ID, so this setting is not meaningful on native-tagged ports.

A port that has more than one interface is a ``bonded port.'' Bonding allows for load balancing and fail-over.

The following types of bonding will work with any kind of upstream switch. On the upstream switch, do not configure the interfaces as a bond:

balance-slb
Balances flows among slaves based on source MAC address and output VLAN, with periodic rebalancing as traffic patterns change.
active-backup
Assigns all flows to one slave, failing over to a backup slave when the active slave is disabled. This is the only bonding mode in which interfaces may be plugged into different upstream switches.

The following modes require the upstream switch to support 802.3ad with successful LACP negotiation. If LACP negotiation fails and other-config:lacp-fallback-ab is true, then active-backup mode is used:

balance-tcp
Balances flows among slaves based on L2, L3, and L4 protocol information such as destination MAC address, IP address, and TCP port.

These columns apply only to bonded ports. Their values are otherwise ignored.

The type of bonding used for a bonded port. Defaults to active-backup if unset.

An integer hashed along with flows when choosing output slaves in load balanced bonds. When changed, all flows will be assigned different hash values possibly causing slave selection decisions to change. Does not affect bonding modes which do not employ load balancing such as active-backup.

An important part of link bonding is detecting that links are down so that they may be disabled. These settings determine how Open vSwitch detects link failure.

The means used to detect link failures. Defaults to carrier which uses each interface's carrier to detect failures. When set to miimon, will check for failures by polling each interface's MII. The interval, in milliseconds, between successive attempts to poll each interface's MII. Relevant only when is miimon.

The number of milliseconds for which the link must stay up on an interface before the interface is considered to be up. Specify 0 to enable the interface immediately.

This setting is honored only when at least one bonded interface is already enabled. When no interfaces are enabled, then the first bond interface to come up is enabled immediately.

The number of milliseconds for which the link must stay down on an interface before the interface is considered to be down. Specify 0 to disable the interface immediately.

LACP, the Link Aggregation Control Protocol, is an IEEE standard that allows switches to automatically detect that they are connected by multiple links and aggregate across those links. These settings control LACP behavior.

Configures LACP on this port. LACP allows directly connected switches to negotiate which links may be bonded. LACP may be enabled on non-bonded ports for the benefit of any switches they may be connected to. active ports are allowed to initiate LACP negotiations. passive ports are allowed to participate in LACP negotiations initiated by a remote switch, but not allowed to initiate such negotiations themselves. If LACP is enabled on a port whose partner switch does not support LACP, the bond will be disabled, unless other-config:lacp-fallback-ab is set to true. Defaults to off if unset. The LACP system ID of this . The system ID of a LACP bond is used to identify itself to its partners. Must be a nonzero MAC address. Defaults to the bridge Ethernet address if unset. The LACP system priority of this . In LACP negotiations, link status decisions are made by the system with the numerically lower priority.

The LACP timing which should be used on this . By default slow is used. When configured to be fast LACP heartbeats are requested at a rate of once per second causing connectivity problems to be detected more quickly. In slow mode, heartbeats are requested at a rate of once every 30 seconds.

Determines the behavior of openvswitch bond in LACP mode. If the partner switch does not support LACP, setting this option to true allows openvswitch to fallback to active-backup. If the option is set to false, the bond will be disabled. In both the cases, once the partner switch is configured to LACP mode, the bond will use LACP.

These settings control behavior when a bond is in balance-slb or balance-tcp mode.

For a load balanced bonded port, the number of milliseconds between successive attempts to rebalance the bond, that is, to move flows from one interface on the bond to another in an attempt to keep usage of each interface roughly equal. If zero, load balancing is disabled on the bond (link failure still cause flows to move). If less than 1000ms, the rebalance interval will be 1000ms.
For a bonded port, whether to create a fake internal interface with the name of the port. Use only for compatibility with legacy software that requires this.

The configuration here is only meaningful, and the status is only populated, when 802.1D-1998 Spanning Tree Protocol is enabled on the port's with its column.

When STP is enabled on a bridge, it is enabled by default on all of the bridge's ports except bond, internal, and mirror ports (which do not work with STP). If this column's value is false, STP is disabled on the port. The port number used for the lower 8 bits of the port-id. By default, the numbers will be assigned automatically. If any port's number is manually configured on a bridge, then they must all be. The port's relative priority value for determining the root port (the upper 8 bits of the port-id). A port with a lower port-id will be chosen as the root port. By default, the priority is 0x80. Spanning tree path cost for the port. A lower number indicates a faster link. By default, the cost is based on the maximum speed of the link. The port ID used in spanning tree advertisements for this port, as 4 hex digits. Configuring the port ID is described in the stp-port-num and stp-port-priority keys of the other_config section earlier. STP state of the port. The amount of time this port has been in the current STP state, in seconds. STP role of the port.

The configuration here is only meaningful, and the status and statistics are only populated, when 802.1D-1998 Spanning Tree Protocol is enabled on the port's with its column.

When RSTP is enabled on a bridge, it is enabled by default on all of the bridge's ports except bond, internal, and mirror ports (which do not work with RSTP). If this column's value is false, RSTP is disabled on the port. The port's relative priority value for determining the root port, in multiples of 16. By default, the port priority is 0x80 (128). Any value in the lower 4 bits is rounded off. The significant upper 4 bits become the upper 4 bits of the port-id. A port with the lowest port-id is elected as the root. The local RSTP port number, used as the lower 12 bits of the port-id. By default the port numbers are assigned automatically, and typically may not correspond to the OpenFlow port numbers. A port with the lowest port-id is elected as the root. The port path cost. The Port's contribution, when it is the Root Port, to the Root Path Cost for the Bridge. By default the cost is automatically calculated from the port's speed. The admin edge port parameter for the Port. Default is false. The auto edge port parameter for the Port. Default is true.

The mcheck port parameter for the Port. Default is false. May be set to force the Port Protocol Migration state machine to transmit RST BPDUs for a MigrateTime period, to test whether all STP Bridges on the attached LAN have been removed and the Port can continue to transmit RSTP BPDUs. Setting mcheck has no effect if the Bridge is operating in STP Compatibility mode.

Changing the value from true to false has no effect, but needs to be done if this behavior is to be triggered again by subsequently changing the value from false to true.

The port ID used in spanning tree advertisements for this port, as 4 hex digits. Configuring the port ID is described in the rstp-port-num and rstp-port-priority keys of the other_config section earlier. RSTP role of the port. RSTP state of the port. The port's RSTP designated bridge ID, in the same form as in the table. The port's RSTP designated port ID, as 4 hex digits. The port's RSTP designated path cost. Lower is better. Number of RSTP BPDUs transmitted through this port. Number of valid RSTP BPDUs received by this port. Number of invalid RSTP BPDUs received by this port. The duration covered by the other RSTP statistics, in seconds.

If set to true, multicast packets (except Reports) are unconditionally forwarded to the specific port.

If set to true, multicast Reports are unconditionally forwarded to the specific port.

Quality of Service configuration for this port. The MAC address to use for this port for the purpose of choosing the bridge's MAC address. This column does not necessarily reflect the port's actual MAC address, nor will setting it change the port's actual MAC address. Does this port represent a sub-bridge for its tagged VLAN within the Bridge? See ovs-vsctl(8) for more information. External IDs for a fake bridge (see the column) are defined by prefixing a key with fake-bridge-, e.g. fake-bridge-xs-network-uuids. For a bonded port, record the mac address of the current active slave.

Key-value pairs that report port statistics. The update period is controlled by in the Open_vSwitch table.

Number of STP BPDUs sent on this port by the spanning tree library. Number of STP BPDUs received on this port and accepted by the spanning tree library. Number of bad STP BPDUs received on this port. Bad BPDUs include runt packets and those with an unexpected protocol ID.
The overall purpose of these columns is described under Common Columns at the beginning of this document.
An interface within a . Interface name. Should be alphanumeric and no more than about 8 bytes long. May be the same as the port name, for non-bonded ports. Must otherwise be unique among the names of ports, interfaces, and bridges on a host. A positive interface index as defined for SNMP MIB-II in RFCs 1213 and 2863, if the interface has one, otherwise 0. The ifindex is useful for seamless integration with protocols such as SNMP and sFlow. The MAC address in use by this interface.

Ethernet address to set for this interface. If unset then the default MAC address is used:

  • For the local interface, the default is the lowest-numbered MAC address among the other bridge ports, either the value of the in its record, if set, or its actual MAC (for bonded ports, the MAC of its slave whose name is first in alphabetical order). Internal ports and bridge ports that are used as port mirroring destinations (see the table) are ignored.
  • For other internal interfaces, the default MAC is randomly generated.
  • External interfaces typically have a MAC address associated with their hardware.

Some interfaces may not have a software-controllable MAC address.

If the configuration of the port failed, as indicated by -1 in , Open vSwitch sets this column to an error description in human readable form. Otherwise, Open vSwitch clears this column.

When a client adds a new interface, Open vSwitch chooses an OpenFlow port number for the new port. If the client that adds the port fills in , then Open vSwitch tries to use its value as the OpenFlow port number. Otherwise, or if the requested port number is already in use or cannot be used for another reason, Open vSwitch automatically assigns a free port number. Regardless of how the port number was obtained, Open vSwitch then reports in the port number actually assigned.

Open vSwitch limits the port numbers that it automatically assigns to the range 1 through 32,767, inclusive. Controllers therefore have free use of ports 32,768 and up.

OpenFlow port number for this interface. Open vSwitch sets this column's value, so other clients should treat it as read-only.

The OpenFlow ``local'' port (OFPP_LOCAL) is 65,534. The other valid port numbers are in the range 1 to 65,279, inclusive. Value -1 indicates an error adding the interface.

Requested OpenFlow port number for this interface.

A client should ideally set this column's value in the same database transaction that it uses to create the interface. Open vSwitch version 2.1 and later will honor a later request for a specific port number, althuogh it might confuse some controllers: OpenFlow does not have a way to announce a port number change, so Open vSwitch represents it over OpenFlow as a port deletion followed immediately by a port addition.

If is set or changed to some other port's automatically assigned port number, Open vSwitch chooses a new port number for the latter port.

The interface type. The types supported by a particular instance of Open vSwitch are listed in the column in the table. The following types are defined:

system
An ordinary network device, e.g. eth0 on Linux. Sometimes referred to as ``external interfaces'' since they are generally connected to hardware external to that on which the Open vSwitch is running. The empty string is a synonym for system.
internal
A simulated network device that sends and receives traffic. An internal interface whose is the same as its bridge's is called the ``local interface.'' It does not make sense to bond an internal interface, so the terms ``port'' and ``interface'' are often used imprecisely for internal interfaces.
tap
A TUN/TAP device managed by Open vSwitch.
geneve
An Ethernet over Geneve (http://tools.ietf.org/html/draft-gross-geneve-00) IPv4 tunnel. Geneve supports options as a means to transport additional metadata, however, currently only the 24-bit VNI is supported. This is planned to be extended in the future.
gre
An Ethernet over RFC 2890 Generic Routing Encapsulation over IPv4 tunnel.
ipsec_gre
An Ethernet over RFC 2890 Generic Routing Encapsulation over IPv4 IPsec tunnel.
gre64
It is same as GRE, but it allows 64 bit key. To store higher 32-bits of key, it uses GRE protocol sequence number field. This is non standard use of GRE protocol since OVS does not increment sequence number for every packet at time of encap as expected by standard GRE implementation. See for information on configuring GRE tunnels.
ipsec_gre64
Same as IPSEC_GRE except 64 bit key.
vxlan

An Ethernet tunnel over the UDP-based VXLAN protocol described in RFC 7348.

Open vSwitch uses UDP destination port 4789. The source port used for VXLAN traffic varies on a per-flow basis and is in the ephemeral port range.

lisp

A layer 3 tunnel over the experimental, UDP-based Locator/ID Separation Protocol (RFC 6830).

Only IPv4 and IPv6 packets are supported by the protocol, and they are sent and received without an Ethernet header. Traffic to/from LISP ports is expected to be configured explicitly, and the ports are not intended to participate in learning based switching. As such, they are always excluded from packet flooding.

patch
A pair of virtual devices that act as a patch cable.
null
An ignored interface. Deprecated and slated for removal in February 2013.

These options apply to interfaces with of geneve, gre, ipsec_gre, gre64, ipsec_gre64, vxlan, and lisp.

Each tunnel must be uniquely identified by the combination of , , , and . If two ports are defined that are the same except one has an optional identifier and the other does not, the more specific one is matched first. is considered more specific than if a port defines one and another port defines the other.

Required. The remote tunnel endpoint, one of:

  • An IPv4 address (not a DNS name), e.g. 192.168.0.123. Only unicast endpoints are supported.
  • The word flow. The tunnel accepts packets from any remote tunnel endpoint. To process only packets from a specific remote tunnel endpoint, the flow entries may match on the tun_src field. When sending packets to a remote_ip=flow tunnel, the flow actions must explicitly set the tun_dst field to the IP address of the desired remote tunnel endpoint, e.g. with a set_field action.

The remote tunnel endpoint for any packet received from a tunnel is available in the tun_src field for matching in the flow table.

Optional. The tunnel destination IP that received packets must match. Default is to match all addresses. If specified, may be one of:

  • An IPv4 address (not a DNS name), e.g. 192.168.12.3.
  • The word flow. The tunnel accepts packets sent to any of the local IP addresses of the system running OVS. To process only packets sent to a specific IP address, the flow entries may match on the tun_dst field. When sending packets to a local_ip=flow tunnel, the flow actions may explicitly set the tun_src field to the desired IP address, e.g. with a set_field action. However, while routing the tunneled packet out, the local system may override the specified address with the local IP address configured for the outgoing system interface.

    This option is valid only for tunnels also configured with the remote_ip=flow option.

The tunnel destination IP address for any packet received from a tunnel is available in the tun_dst field for matching in the flow table.

Optional. The key that received packets must contain, one of:

  • 0. The tunnel receives packets with no key or with a key of 0. This is equivalent to specifying no at all.
  • A positive 24-bit (for Geneve, VXLAN, and LISP), 32-bit (for GRE) or 64-bit (for GRE64) number. The tunnel receives only packets with the specified key.
  • The word flow. The tunnel accepts packets with any key. The key will be placed in the tun_id field for matching in the flow table. The ovs-ofctl manual page contains additional information about matching fields in OpenFlow flows.

Optional. The key to be set on outgoing packets, one of:

  • 0. Packets sent through the tunnel will have no key. This is equivalent to specifying no at all.
  • A positive 24-bit (for Geneve, VXLAN and LISP), 32-bit (for GRE) or 64-bit (for GRE64) number. Packets sent through the tunnel will have the specified key.
  • The word flow. Packets sent through the tunnel will have the key set using the set_tunnel Nicira OpenFlow vendor extension (0 is used in the absence of an action). The ovs-ofctl manual page contains additional information about the Nicira OpenFlow vendor extensions.
Optional. Shorthand to set in_key and out_key at the same time. Optional. The value of the ToS bits to be set on the encapsulating packet. ToS is interpreted as DSCP and ECN bits, ECN part must be zero. It may also be the word inherit, in which case the ToS will be copied from the inner packet if it is IPv4 or IPv6 (otherwise it will be 0). The ECN fields are always inherited. Default is 0. Optional. The TTL to be set on the encapsulating packet. It may also be the word inherit, in which case the TTL will be copied from the inner packet if it is IPv4 or IPv6 (otherwise it will be the system default, typically 64). Default is the system default TTL. Optional. If enabled, the Don't Fragment bit will be set on tunnel outer headers to allow path MTU discovery. Default is enabled; set to false to disable.

Optional. Comma separated list of optional VXLAN extensions to enable. The following extensions are supported:

  • gbp: VXLAN-GBP allows to transport the group policy context of a packet across the VXLAN tunnel to other network peers. See the field description of tun_gbp_id and tun_gbp_flags in ovs-ofctl(8) for additional information. (https://tools.ietf.org/html/draft-smith-vxlan-group-policy)

gre, ipsec_gre, geneve, and vxlan interfaces support these options.

Optional. Compute encapsulation header (either GRE or UDP) checksums on outgoing packets. Default is disabled, set to true to enable. Checksums present on incoming packets will be validated regardless of this setting.

When using the upstream Linux kernel module, computation of checksums for geneve and vxlan requires Linux kernel version 4.0 or higher. gre supports checksums for all versions of Open vSwitch that support GRE. The out of tree kernel module distributed as part of OVS can compute all tunnel checksums on any kernel version that it is compatible with.

This option is supported for ipsec_gre, but not useful because GRE checksums are weaker than, and redundant with, IPsec payload authentication.

Only ipsec_gre interfaces support these options.

Required for certificate authentication. A string containing the peer's certificate in PEM format. Additionally the host's certificate must be specified with the certificate option. Required for certificate authentication. The name of a PEM file containing a certificate that will be presented to the peer during authentication. Optional for certificate authentication. The name of a PEM file containing the private key associated with certificate. If certificate contains the private key, this option may be omitted. Required for pre-shared key authentication. Specifies a pre-shared key for authentication that must be identical on both sides of the tunnel.

Only patch interfaces support these options.

The of the for the other side of the patch. The named 's own peer option must specify this 's name. That is, the two patch interfaces must have reversed and peer values.

Status information about interfaces attached to bridges, updated every 5 seconds. Not all interfaces have all of these properties; virtual interfaces don't have a link speed, for example. Non-applicable columns will have empty values.

The administrative state of the physical network link.

The observed state of the physical network link. This is ordinarily the link's carrier status. If the interface's is a bond configured for miimon monitoring, it is instead the network link's miimon status.

The number of times Open vSwitch has observed the of this change.

The negotiated speed of the physical network link. Valid values are positive integers greater than 0.

The duplex mode of the physical network link.

The MTU (maximum transmission unit); i.e. the largest amount of data that can fit into a single Ethernet frame. The standard Ethernet MTU is 1500 bytes. Some physical media and many kinds of virtual interfaces can be configured with higher MTUs.

This column will be empty for an interface that does not have an MTU as, for example, some kinds of tunnels do not.

Boolean value indicating LACP status for this interface. If true, this interface has current LACP information about its LACP partner. This information may be used to monitor the health of interfaces in a LACP enabled port. This column will be empty if LACP is not enabled. Key-value pairs that report port status. Supported status values are -dependent; some interfaces may not have a valid , for example. The name of the device driver controlling the network adapter. The version string of the device driver controlling the network adapter. The version string of the network adapter's firmware, if available. The source IP address used for an IPv4 tunnel end-point, such as gre. Egress interface for tunnels. Currently only relevant for tunnels on Linux systems, this column will show the name of the interface which is responsible for routing traffic destined for the configured . This could be an internal interface such as a bridge port. Whether carrier is detected on .

Key-value pairs that report interface statistics. The current implementation updates these counters periodically. The update period is controlled by in the Open_vSwitch table. Future implementations may update them when an interface is created, when they are queried (e.g. using an OVSDB select operation), and just before an interface is deleted due to virtual interface hot-unplug or VM shutdown, and perhaps at other times, but not on any regular periodic basis.

These are the same statistics reported by OpenFlow in its struct ofp_port_stats structure. If an interface does not support a given statistic, then that pair is omitted.

Number of received packets. Number of received bytes. Number of transmitted packets. Number of transmitted bytes. Number of packets dropped by RX. Number of frame alignment errors. Number of packets with RX overrun. Number of CRC errors. Total number of receive errors, greater than or equal to the sum of the above. Number of packets dropped by TX. Number of collisions. Total number of transmit errors, greater than or equal to the sum of the above.

These settings control ingress policing for packets received on this interface. On a physical interface, this limits the rate at which traffic is allowed into the system from the outside; on a virtual interface (one connected to a virtual machine), this limits the rate at which the VM is able to transmit.

Policing is a simple form of quality-of-service that simply drops packets received in excess of the configured rate. Due to its simplicity, policing is usually less accurate and less effective than egress QoS (which is configured using the and tables).

Policing is currently implemented only on Linux. The Linux implementation uses a simple ``token bucket'' approach:

  • The size of the bucket corresponds to . Initially the bucket is full.
  • Whenever a packet is received, its size (converted to tokens) is compared to the number of tokens currently in the bucket. If the required number of tokens are available, they are removed and the packet is forwarded. Otherwise, the packet is dropped.
  • Whenever it is not full, the bucket is refilled with tokens at the rate specified by .

Policing interacts badly with some network protocols, and especially with fragmented IP packets. Suppose that there is enough network activity to keep the bucket nearly empty all the time. Then this token bucket algorithm will forward a single packet every so often, with the period depending on packet size and on the configured rate. All of the fragments of an IP packets are normally transmitted back-to-back, as a group. In such a situation, therefore, only one of these fragments will be forwarded and the rest will be dropped. IP does not provide any way for the intended recipient to ask for only the remaining fragments. In such a case there are two likely possibilities for what will happen next: either all of the fragments will eventually be retransmitted (as TCP will do), in which case the same problem will recur, or the sender will not realize that its packet has been dropped and data will simply be lost (as some UDP-based protocols will do). Either way, it is possible that no forward progress will ever occur.

Maximum rate for data received on this interface, in kbps. Data received faster than this rate is dropped. Set to 0 (the default) to disable policing.

Maximum burst size for data received on this interface, in kb. The default burst size if set to 0 is 1000 kb. This value has no effect if is 0.

Specifying a larger burst size lets the algorithm be more forgiving, which is important for protocols like TCP that react severely to dropped packets. The burst size should be at least the size of the interface's MTU. Specifying a value that is numerically at least as large as 10% of helps TCP come closer to achieving the full rate.

BFD, defined in RFC 5880 and RFC 5881, allows point-to-point detection of connectivity failures by occasional transmission of BFD control messages. Open vSwitch implements BFD to serve as a more popular and standards compliant alternative to CFM.

BFD operates by regularly transmitting BFD control messages at a rate negotiated independently in each direction. Each endpoint specifies the rate at which it expects to receive control messages, and the rate at which it is willing to transmit them. Open vSwitch uses a detection multiplier of three, meaning that an endpoint signals a connectivity fault if three consecutive BFD control messages fail to arrive. In the case of a unidirectional connectivity issue, the system not receiving BFD control messages signals the problem to its peer in the messages it transmits.

The Open vSwitch implementation of BFD aims to comply faithfully with RFC 5880 requirements. Open vSwitch does not implement the optional Authentication or ``Echo Mode'' features.

A controller sets up key-value pairs in the column to enable and configure BFD.

True to enable BFD on this . If not specified, BFD will not be enabled by default. The shortest interval, in milliseconds, at which this BFD session offers to receive BFD control messages. The remote endpoint may choose to send messages at a slower rate. Defaults to 1000. The shortest interval, in milliseconds, at which this BFD session is willing to transmit BFD control messages. Messages will actually be transmitted at a slower rate if the remote endpoint is not willing to receive as quickly as specified. Defaults to 100. An alternate receive interval, in milliseconds, that must be greater than or equal to . The implementation switches from to when there is no obvious incoming data traffic at the interface, to reduce the CPU and bandwidth cost of monitoring an idle interface. This feature may be disabled by setting a value of 0. This feature is reset whenever or changes. When true, traffic received on the is used to indicate the capability of packet I/O. BFD control packets are still transmitted and received. At least one BFD control packet must be received every 100 * amount of time. Otherwise, even if traffic are received, the will be false. Set to true to notify the remote endpoint that traffic should not be forwarded to this system for some reason other than a connectivty failure on the interface being monitored. The typical underlying reason is ``concatenated path down,'' that is, that connectivity beyond the local system is down. Defaults to false. Set to true to make BFD accept only control messages with a tunnel key of zero. By default, BFD accepts control messages with any tunnel key. Set to an Ethernet address in the form xx:xx:xx:xx:xx:xx to set the MAC used as source for transmitted BFD packets. The default is the mac address of the BFD enabled interface. Set to an Ethernet address in the form xx:xx:xx:xx:xx:xx to set the MAC used as destination for transmitted BFD packets. The default is 00:23:20:00:00:01. Set to an Ethernet address in the form xx:xx:xx:xx:xx:xx to set the MAC used for checking the destination of received BFD packets. Packets with different destination MAC will not be considered as BFD packets. If not specified the destination MAC address of received BFD packets are not checked. Set to an IPv4 address to set the IP address used as source for transmitted BFD packets. The default is 169.254.1.1. Set to an IPv4 address to set the IP address used as destination for transmitted BFD packets. The default is 169.254.1.0.

The switch sets key-value pairs in the column to report the status of BFD on this interface. When BFD is not enabled, with , the switch clears all key-value pairs from .

Reports the state of the BFD session. The BFD session is fully healthy and negotiated if UP. Reports whether the BFD session believes this may be used to forward traffic. Typically this means the local session is signaling UP, and the remote system isn't signaling a problem such as concatenated path down. In case of a problem, set to an error message that reports what the local BFD session thinks is wrong. The error messages are defined in section 4.1 of [RFC 5880]. Reports the state of the remote endpoint's BFD session. In case of a problem, set to an error message that reports what the remote endpoint's BFD session thinks is wrong. The error messages are defined in section 4.1 of [RFC 5880]. Counts the number of flaps since start. A flap is considered as a change of the value.

802.1ag Connectivity Fault Management (CFM) allows a group of Maintenance Points (MPs) called a Maintenance Association (MA) to detect connectivity problems with each other. MPs within a MA should have complete and exclusive interconnectivity. This is verified by occasionally broadcasting Continuity Check Messages (CCMs) at a configurable transmission interval.

According to the 802.1ag specification, each Maintenance Point should be configured out-of-band with a list of Remote Maintenance Points it should have connectivity to. Open vSwitch differs from the specification in this area. It simply assumes the link is faulted if no Remote Maintenance Points are reachable, and considers it not faulted otherwise.

When operating over tunnels which have no in_key, or an in_key of flow. CFM will only accept CCMs with a tunnel key of zero.

A Maintenance Point ID (MPID) uniquely identifies each endpoint within a Maintenance Association. The MPID is used to identify this endpoint to other Maintenance Points in the MA. Each end of a link being monitored should have a different MPID. Must be configured to enable CFM on this .

According to the 802.1ag specification, MPIDs can only range between [1, 8191]. However, extended mode (see ) supports eight byte MPIDs.

Counts the number of cfm fault flapps since boot. A flap is considered to be a change of the value.

Indicates a connectivity fault triggered by an inability to receive heartbeats from any remote endpoint. When a fault is triggered on s participating in bonds, they will be disabled.

Faults can be triggered for several reasons. Most importantly they are triggered when no CCMs are received for a period of 3.5 times the transmission interval. Faults are also triggered when any CCMs indicate that a Remote Maintenance Point is not receiving CCMs but able to send them. Finally, a fault is triggered if a CCM is received which indicates unexpected configuration. Notably, this case arises when a CCM is received which advertises the local MPID.

Indicates a CFM fault was triggered due to a lack of CCMs received on the . Indicates a CFM fault was triggered due to the reception of a CCM with the RDI bit flagged. Endpoints set the RDI bit in their CCMs when they are not receiving CCMs themselves. This typically indicates a unidirectional connectivity failure. Indicates a CFM fault was triggered due to the reception of a CCM with a MAID other than the one Open vSwitch uses. CFM broadcasts are tagged with an identification number in addition to the MPID called the MAID. Open vSwitch only supports receiving CCM broadcasts tagged with the MAID it uses internally. Indicates a CFM fault was triggered due to the reception of a CCM advertising the same MPID configured in the column of this . This may indicate a loop in the network. Indicates a CFM fault was triggered because the CFM module received CCMs from more remote endpoints than it can keep track of. Indicates a CFM fault was manually triggered by an administrator using an ovs-appctl command. Indicates a CFM fault was triggered due to the reception of a CCM frame having an invalid interval.

When in extended mode, indicates the operational state of the remote endpoint as either up or down. See .

Indicates the health of the interface as a percentage of CCM frames received over 21 s. The health of an interface is undefined if it is communicating with more than one . It reduces if healthy heartbeats are not received at the expected rate, and gradually improves as healthy heartbeats are received at the desired rate. Every 21 s, the health of the interface is refreshed.

As mentioned above, the faults can be triggered for several reasons. The link health will deteriorate even if heartbeats are received but they are reported to be unhealthy. An unhealthy heartbeat in this context is a heartbeat for which either some fault is set or is out of sequence. The interface health can be 100 only on receiving healthy heartbeats at the desired rate.

When CFM is properly configured, Open vSwitch will occasionally receive CCM broadcasts. These broadcasts contain the MPID of the sending Maintenance Point. The list of MPIDs from which this is receiving broadcasts from is regularly collected and written to this column.

The interval, in milliseconds, between transmissions of CFM heartbeats. Three missed heartbeat receptions indicate a connectivity fault.

In standard operation only intervals of 3, 10, 100, 1,000, 10,000, 60,000, or 600,000 ms are supported. Other values will be rounded down to the nearest value on the list. Extended mode (see ) supports any interval up to 65,535 ms. In either mode, the default is 1000 ms.

We do not recommend using intervals less than 100 ms.

When true, the CFM module operates in extended mode. This causes it to use a nonstandard destination address to avoid conflicting with compliant implementations which may be running concurrently on the network. Furthermore, extended mode increases the accuracy of the cfm_interval configuration parameter by breaking wire compatibility with 802.1ag compliant implementations. And extended mode allows eight byte MPIDs. Defaults to false.

When true, and is true, the CFM module operates in demand mode. When in demand mode, traffic received on the is used to indicate liveness. CCMs are still transmitted and received. At least one CCM must be received every 100 * amount of time. Otherwise, even if traffic are received, the CFM module will raise the connectivity fault.

Demand mode has a couple of caveats:

  • To ensure that ovs-vswitchd has enough time to pull statistics from the datapath, the fault detection interval is set to 3.5 * MAX(, 500) ms.
  • To avoid ambiguity, demand mode disables itself when there are multiple remote maintenance points.
  • If the is heavily congested, CCMs containing the status may be dropped causing changes in the operational state to be delayed. Similarly, if CCMs containing the RDI bit are not received, unidirectional link failures may not be detected.

When down, the CFM module marks all CCMs it generates as operationally down without triggering a fault. This allows remote maintenance points to choose not to forward traffic to the on which this CFM module is running. Currently, in Open vSwitch, the opdown bit of CCMs affects s participating in bonds, and the bundle OpenFlow action. This setting is ignored when CFM is not in extended mode. Defaults to up. When set, the CFM module will apply a VLAN tag to all CCMs it generates with the given value. May be the string random in which case each CCM will be tagged with a different randomly generated VLAN. When set, the CFM module will apply a VLAN tag to all CCMs it generates with the given PCP value, the VLAN ID of the tag is governed by the value of . If is unset, a VLAN ID of zero is used.
The LACP port ID of this . Port IDs are used in LACP negotiations to identify individual ports participating in a bond. The LACP port priority of this . In LACP negotiations s with numerically lower priorities are preferred for aggregation. The LACP aggregation key of this . s with different aggregation keys may not be active within a given at the same time.

These key-value pairs specifically apply to an interface that represents a virtual Ethernet interface connected to a virtual machine. These key-value pairs should not be present for other types of interfaces. Keys whose names end in -uuid have values that uniquely identify the entity in question. For a Citrix XenServer hypervisor, these values are UUIDs in RFC 4122 format. Other hypervisors may use other formats.

The MAC address programmed into the ``virtual hardware'' for this interface, in the form xx:xx:xx:xx:xx:xx. For Citrix XenServer, this is the value of the MAC field in the VIF record for this interface. A system-unique identifier for the interface. On XenServer, this will commonly be the same as .

Hypervisors may sometimes have more than one interface associated with a given , only one of which is actually in use at a given time. For example, in some circumstances XenServer has both a ``tap'' and a ``vif'' interface for a single , but only uses one of them at a time. A hypervisor that behaves this way must mark the currently in use interface active and the others inactive. A hypervisor that never has more than one interface for a given may mark that interface active or omit entirely.

During VM migration, a given might transiently be marked active on two different hypervisors. That is, active means that this is the active instance within a single hypervisor, not in a broader scope. There is one exception: some hypervisors support ``migration'' from a given hypervisor to itself (most often for test purposes). During such a ``migration,'' two instances of a single might both be briefly marked active on a single hypervisor.

The virtual interface associated with this interface. The virtual network to which this interface is attached. The VM to which this interface belongs. On XenServer, this will be the same as . The VM to which this interface belongs.

The ``VLAN splinters'' feature increases Open vSwitch compatibility with buggy network drivers in old versions of Linux that do not properly support VLANs when VLAN devices are not used, at some cost in memory and performance.

When VLAN splinters are enabled on a particular interface, Open vSwitch creates a VLAN device for each in-use VLAN. For sending traffic tagged with a VLAN on the interface, it substitutes the VLAN device. Traffic received on the VLAN device is treated as if it had been received on the interface on the particular VLAN.

VLAN splinters consider a VLAN to be in use if:

  • The VLAN is the value in any record.
  • The VLAN is listed within the column of the record of an interface on which VLAN splinters are enabled. An empty does not influence the in-use VLANs: creating 4,096 VLAN devices is impractical because it will exceed the current 1,024 port per datapath limit.
  • An OpenFlow flow within any bridge matches the VLAN.

The same set of in-use VLANs applies to every interface on which VLAN splinters are enabled. That is, the set is not chosen separately for each interface but selected once as the union of all in-use VLANs based on the rules above.

It does not make sense to enable VLAN splinters on an interface for an access port, or on an interface that is not a physical port.

VLAN splinters are deprecated. When broken device drivers are no longer in widespread use, we will delete this feature.

Set to true to enable VLAN splinters on this interface. Defaults to false.

VLAN splinters increase kernel and userspace memory overhead, so do not use them unless they are needed.

VLAN splinters do not support 802.1p priority tags. Received priorities will appear to be 0, regardless of their actual values, and priorities on transmitted packets will also be cleared to 0.

Auto Attach configuration for a particular interface.

True to enable LLDP on this . If not specified, LLDP will be disabled by default.
The overall purpose of these columns is described under Common Columns at the beginning of this document.

Configuration for a particular OpenFlow table.

The table's name. Set this column to change the name that controllers will receive when they request table statistics, e.g. ovs-ofctl dump-tables. The name does not affect switch behavior. If set, limits the number of flows that may be added to the table. Open vSwitch may limit the number of flows in a table for other reasons, e.g. due to hardware limitations or for resource availability or performance reasons.

Controls the switch's behavior when an OpenFlow flow table modification request would add flows in excess of . The supported values are:

refuse
Refuse to add the flow or flows. This is also the default policy when is unset.
evict
Delete the flow that will expire soonest. See for details.

When is evict, this controls how flows are chosen for eviction when the flow table would otherwise exceed flows. Its value is a set of NXM fields or sub-fields, each of which takes one of the forms field[] or field[start..end], e.g. NXM_OF_IN_PORT[]. Please see nicira-ext.h for a complete list of NXM field names.

When a flow must be evicted due to overflow, the flow to evict is chosen through an approximation of the following algorithm:

  1. Divide the flows in the table into groups based on the values of the specified fields or subfields, so that all of the flows in a given group have the same values for those fields. If a flow does not specify a given field, that field's value is treated as 0.
  2. Consider the flows in the largest group, that is, the group that contains the greatest number of flows. If two or more groups all have the same largest number of flows, consider the flows in all of those groups.
  3. Among the flows under consideration, choose the flow that expires soonest for eviction.

The eviction process only considers flows that have an idle timeout or a hard timeout. That is, eviction never deletes permanent flows. (Permanent flows do count against .)

Open vSwitch ignores any invalid or unknown field specifications.

When is not evict, this column has no effect.

This string set specifies which fields should be used for address prefix tracking. Prefix tracking allows the classifier to skip rules with longer than necessary prefixes, resulting in better wildcarding for datapath flows.

Prefix tracking may be beneficial when a flow table contains matches on IP address fields with different prefix lengths. For example, when a flow table contains IP address matches on both full addresses and proper prefixes, the full address matches will typically cause the datapath flow to un-wildcard the whole address field (depending on flow entry priorities). In this case each packet with a different address gets handed to the userspace for flow processing and generates its own datapath flow. With prefix tracking enabled for the address field in question packets with addresses matching shorter prefixes would generate datapath flows where the irrelevant address bits are wildcarded, allowing the same datapath flow to handle all the packets within the prefix in question. In this case many userspace upcalls can be avoided and the overall performance can be better.

This is a performance optimization only, so packets will receive the same treatment with or without prefix tracking.

The supported fields are: tun_id, tun_src, tun_dst, nw_src, nw_dst (or aliases ip_src and ip_dst), ipv6_src, and ipv6_dst. (Using this feature for tun_id would only make sense if the tunnel IDs have prefix structure similar to IP addresses.)

By default, the prefixes=ip_dst,ip_src are used on each flow table. This instructs the flow classifier to track the IP destination and source addresses used by the rules in this specific flow table.

The keyword none is recognized as an explicit override of the default values, causing no prefix fields to be tracked.

To set the prefix fields, the flow table record needs to exist:

ovs-vsctl set Bridge br0 flow_tables:0=@N1 -- --id=@N1 create Flow_Table name=table0
Creates a flow table record for the OpenFlow table number 0.
ovs-vsctl set Flow_Table table0 prefixes=ip_dst,ip_src
Enables prefix tracking for IP source and destination address fields.

There is a maximum number of fields that can be enabled for any one flow table. Currently this limit is 3.

The overall purpose of these columns is described under Common Columns at the beginning of this document.

Quality of Service (QoS) configuration for each Port that references it.

The type of QoS to implement. The currently defined types are listed below:

linux-htb
Linux ``hierarchy token bucket'' classifier. See tc-htb(8) (also at http://linux.die.net/man/8/tc-htb) and the HTB manual (http://luxik.cdi.cz/~devik/qos/htb/manual/userg.htm) for information on how this classifier works and how to configure it.
linux-hfsc
Linux "Hierarchical Fair Service Curve" classifier. See http://linux-ip.net/articles/hfsc.en/ for information on how this classifier works.
linux-sfq
Linux ``Stochastic Fairness Queueing'' classifier. See tc-sfq(8) (also at http://linux.die.net/man/8/tc-sfq) for information on how this classifier works.
linux-codel
Linux ``Controlled Delay'' classifier. See tc-codel(8) (also at http://man7.org/linux/man-pages/man8/tc-codel.8.html) for information on how this classifier works.
linux-fq_codel
Linux ``Fair Queuing with Controlled Delay'' classifier. See tc-fq_codel(8) (also at http://man7.org/linux/man-pages/man8/tc-fq_codel.8.html) for information on how this classifier works.

A map from queue numbers to records. The supported range of queue numbers depend on . The queue numbers are the same as the queue_id used in OpenFlow in struct ofp_action_enqueue and other structures.

Queue 0 is the ``default queue.'' It is used by OpenFlow output actions when no specific queue has been set. When no configuration for queue 0 is present, it is automatically configured as if a record with empty and columns had been specified. (Before version 1.6, Open vSwitch would leave queue 0 unconfigured in this case. With some queuing disciplines, this dropped all packets destined for the default queue.)

The linux-htb and linux-hfsc classes support the following key-value pair:

Maximum rate shared by all queued traffic, in bit/s. Optional. If not specified, for physical interfaces, the default is the link rate. For other interfaces or if the link rate cannot be determined, the default is currently 100 Mbps.
The overall purpose of these columns is described under Common Columns at the beginning of this document.

A configuration for a port output queue, used in configuring Quality of Service (QoS) features. May be referenced by column in table.

If set, Open vSwitch will mark all traffic egressing this with the given DSCP bits. Traffic egressing the default is only marked if it was explicitly selected as the at the time the packet was output. If unset, the DSCP bits of traffic egressing this will remain unchanged.

linux-htb may use queue_ids less than 61440. It has the following key-value pairs defined.

Minimum guaranteed bandwidth, in bit/s. Maximum allowed bandwidth, in bit/s. Optional. If specified, the queue's rate will not be allowed to exceed the specified value, even if excess bandwidth is available. If unspecified, defaults to no limit. Burst size, in bits. This is the maximum amount of ``credits'' that a queue can accumulate while it is idle. Optional. Details of the linux-htb implementation require a minimum burst size, so a too-small burst will be silently ignored. A queue with a smaller priority will receive all the excess bandwidth that it can use before a queue with a larger value receives any. Specific priority values are unimportant; only relative ordering matters. Defaults to 0 if unspecified.

linux-hfsc may use queue_ids less than 61440. It has the following key-value pairs defined.

Minimum guaranteed bandwidth, in bit/s. Maximum allowed bandwidth, in bit/s. Optional. If specified, the queue's rate will not be allowed to exceed the specified value, even if excess bandwidth is available. If unspecified, defaults to no limit.
The overall purpose of these columns is described under Common Columns at the beginning of this document.

A port mirror within a .

A port mirror configures a bridge to send selected frames to special ``mirrored'' ports, in addition to their normal destinations. Mirroring traffic may also be referred to as SPAN or RSPAN, depending on how the mirrored traffic is sent.

Arbitrary identifier for the .

To be selected for mirroring, a given packet must enter or leave the bridge through a selected port and it must also be in one of the selected VLANs.

If true, every packet arriving or departing on any port is selected for mirroring. Ports on which departing packets are selected for mirroring. Ports on which arriving packets are selected for mirroring. VLANs on which packets are selected for mirroring. An empty set selects packets on all VLANs.

These columns are mutually exclusive. Exactly one of them must be nonempty.

Output port for selected packets, if nonempty.

Specifying a port for mirror output reserves that port exclusively for mirroring. No frames other than those selected for mirroring via this column will be forwarded to the port, and any frames received on the port will be discarded.

The output port may be any kind of port supported by Open vSwitch. It may be, for example, a physical port (sometimes called SPAN) or a GRE tunnel.

Output VLAN for selected packets, if nonempty.

The frames will be sent out all ports that trunk , as well as any ports with implicit VLAN . When a mirrored frame is sent out a trunk port, the frame's VLAN tag will be set to , replacing any existing tag; when it is sent out an implicit VLAN port, the frame will not be tagged. This type of mirroring is sometimes called RSPAN.

See the documentation for in the table for a list of destination MAC addresses which will not be mirrored to a VLAN to avoid confusing switches that interpret the protocols that they represent.

Please note: Mirroring to a VLAN can disrupt a network that contains unmanaged switches. Consider an unmanaged physical switch with two ports: port 1, connected to an end host, and port 2, connected to an Open vSwitch configured to mirror received packets into VLAN 123 on port 2. Suppose that the end host sends a packet on port 1 that the physical switch forwards to port 2. The Open vSwitch forwards this packet to its destination and then reflects it back on port 2 in VLAN 123. This reflected packet causes the unmanaged physical switch to replace the MAC learning table entry, which correctly pointed to port 1, with one that incorrectly points to port 2. Afterward, the physical switch will direct packets destined for the end host to the Open vSwitch on port 2, instead of to the end host on port 1, disrupting connectivity. If mirroring to a VLAN is desired in this scenario, then the physical switch must be replaced by one that learns Ethernet addresses on a per-VLAN basis. In addition, learning should be disabled on the VLAN containing mirrored traffic. If this is not done then intermediate switches will learn the MAC address of each end host from the mirrored traffic. If packets being sent to that end host are also mirrored, then they will be dropped since the switch will attempt to send them out the input port. Disabling learning for the VLAN will cause the switch to correctly send the packet out all ports configured for that VLAN. If Open vSwitch is being used as an intermediate switch, learning can be disabled by adding the mirrored VLAN to in the appropriate table or tables.

Mirroring to a GRE tunnel has fewer caveats than mirroring to a VLAN and should generally be preferred.

Key-value pairs that report mirror statistics. The update period is controlled by in the Open_vSwitch table.

Number of packets transmitted through this mirror. Number of bytes transmitted through this mirror.
The overall purpose of these columns is described under Common Columns at the beginning of this document.

An OpenFlow controller.

Open vSwitch supports two kinds of OpenFlow controllers:

Primary controllers

This is the kind of controller envisioned by the OpenFlow 1.0 specification. Usually, a primary controller implements a network policy by taking charge of the switch's flow table.

Open vSwitch initiates and maintains persistent connections to primary controllers, retrying the connection each time it fails or drops. The column in the table applies to primary controllers.

Open vSwitch permits a bridge to have any number of primary controllers. When multiple controllers are configured, Open vSwitch connects to all of them simultaneously. Because OpenFlow 1.0 does not specify how multiple controllers coordinate in interacting with a single switch, more than one primary controller should be specified only if the controllers are themselves designed to coordinate with each other. (The Nicira-defined NXT_ROLE OpenFlow vendor extension may be useful for this.)

Service controllers

These kinds of OpenFlow controller connections are intended for occasional support and maintenance use, e.g. with ovs-ofctl. Usually a service controller connects only briefly to inspect or modify some of a switch's state.

Open vSwitch listens for incoming connections from service controllers. The service controllers initiate and, if necessary, maintain the connections from their end. The column in the table does not apply to service controllers.

Open vSwitch supports configuring any number of service controllers.

The determines the type of controller.

Connection method for controller.

The following connection methods are currently supported for primary controllers:

ssl:ip[:port]

The specified SSL port on the host at the given ip, which must be expressed as an IP address (not a DNS name). The column in the table must point to a valid SSL configuration when this form is used.

If port is not specified, it defaults to 6653.

SSL support is an optional feature that is not always built as part of Open vSwitch.

tcp:ip[:port]

The specified TCP port on the host at the given ip, which must be expressed as an IP address (not a DNS name), where ip can be IPv4 or IPv6 address. If ip is an IPv6 address, wrap it in square brackets, e.g. tcp:[::1]:6653.

If port is not specified, it defaults to 6653.

The following connection methods are currently supported for service controllers:

pssl:[port][:ip]

Listens for SSL connections on the specified TCP port. If ip, which must be expressed as an IP address (not a DNS name), is specified, then connections are restricted to the specified local IP address (either IPv4 or IPv6). If ip is an IPv6 address, wrap it in square brackets, e.g. pssl:6653:[::1].

If port is not specified, it defaults to 6653. If ip is not specified then it listens only on IPv4 (but not IPv6) addresses. The column in the table must point to a valid SSL configuration when this form is used.

If port is not specified, it currently to 6653.

SSL support is an optional feature that is not always built as part of Open vSwitch.

ptcp:[port][:ip]

Listens for connections on the specified TCP port. If ip, which must be expressed as an IP address (not a DNS name), is specified, then connections are restricted to the specified local IP address (either IPv4 or IPv6). If ip is an IPv6 address, wrap it in square brackets, e.g. ptcp:6653:[::1]. If ip is not specified then it listens only on IPv4 addresses.

If port is not specified, it defaults to 6653.

When multiple controllers are configured for a single bridge, the values must be unique. Duplicate values yield unspecified results.

If it is specified, this setting must be one of the following strings that describes how Open vSwitch contacts this OpenFlow controller over the network:

in-band
In this mode, this controller's OpenFlow traffic travels over the bridge associated with the controller. With this setting, Open vSwitch allows traffic to and from the controller regardless of the contents of the OpenFlow flow table. (Otherwise, Open vSwitch would never be able to connect to the controller, because it did not have a flow to enable it.) This is the most common connection mode because it is not necessary to maintain two independent networks.
out-of-band
In this mode, OpenFlow traffic uses a control network separate from the bridge associated with this controller, that is, the bridge does not use any of its own network devices to communicate with the controller. The control network must be configured separately, before or after ovs-vswitchd is started.

If not specified, the default is implementation-specific.

Maximum number of milliseconds to wait between connection attempts. Default is implementation-specific. Maximum number of milliseconds of idle time on connection to controller before sending an inactivity probe message. If Open vSwitch does not communicate with the controller for the specified number of seconds, it will send a probe. If a response is not received for the same additional amount of time, Open vSwitch assumes the connection has been broken and attempts to reconnect. Default is implementation-specific. A value of 0 disables inactivity probes.

OpenFlow switches send certain messages to controllers spontanenously, that is, not in response to any request from the controller. These messages are called ``asynchronous messages.'' These columns allow asynchronous messages to be limited or disabled to ensure the best use of network resources.

The OpenFlow protocol enables asynchronous messages at time of connection establishment, which means that a controller can receive asynchronous messages, potentially many of them, even if it turns them off immediately after connecting. Set this column to false to change Open vSwitch behavior to disable, by default, all asynchronous messages. The controller can use the NXT_SET_ASYNC_CONFIG Nicira extension to OpenFlow to turn on any messages that it does want to receive, if any.

A switch can forward packets to a controller over the OpenFlow protocol. Forwarding packets this way at too high a rate can overwhelm a controller, frustrate use of the OpenFlow connection for other purposes, increase the latency of flow setup, and use an unreasonable amount of bandwidth. Therefore, Open vSwitch supports limiting the rate of packet forwarding to a controller.

There are two main reasons in OpenFlow for a packet to be sent to a controller: either the packet ``misses'' in the flow table, that is, there is no matching flow, or a flow table action says to send the packet to the controller. Open vSwitch limits the rate of each kind of packet separately at the configured rate. Therefore, the actual rate that packets are sent to the controller can be up to twice the configured rate, when packets are sent for both reasons.

This feature is specific to forwarding packets over an OpenFlow connection. It is not general-purpose QoS. See the table for quality of service configuration, and in the table for ingress policing configuration.

The maximum rate at which the switch will forward packets to the OpenFlow controller, in packets per second. If no value is specified, rate limiting is disabled.

When a high rate triggers rate-limiting, Open vSwitch queues packets to the controller for each port and transmits them to the controller at the configured rate. This value limits the number of queued packets. Ports on a bridge share the packet queue fairly.

This value has no effect unless is configured. The current default when this value is not specified is one-quarter of , meaning that queuing can delay forwarding a packet to the controller by up to 250 ms.

These values report the effects of rate limiting. Their values are relative to establishment of the most recent OpenFlow connection, or since rate limiting was enabled, whichever happened more recently. Each consists of two values, one with TYPE replaced by miss for rate limiting flow table misses, and the other with TYPE replaced by action for rate limiting packets sent by OpenFlow actions.

These statistics are reported only when controller rate limiting is enabled.

Number of packets sent directly to the controller, without queuing, because the rate did not exceed the configured maximum. Number of packets added to the queue to send later. Number of packets added to the queue that were later dropped due to overflow. This value is less than or equal to . Number of packets currently queued. The other statistics increase monotonically, but this one fluctuates between 0 and the as conditions change.

These values are considered only in in-band control mode (see ).

When multiple controllers are configured on a single bridge, there should be only one set of unique values in these columns. If different values are set for these columns in different controllers, the effect is unspecified.

The IP address to configure on the local port, e.g. 192.168.0.123. If this value is unset, then and are ignored. The IP netmask to configure on the local port, e.g. 255.255.255.0. If is set but this value is unset, then the default is chosen based on whether the IP address is class A, B, or C. The IP address of the gateway to configure on the local port, as a string, e.g. 192.168.0.1. Leave this column unset if this network has no gateway.
true if currently connected to this controller, false otherwise.

The level of authority this controller has on the associated bridge. Possible values are:

other
Allows the controller access to all OpenFlow features.
master
Equivalent to other, except that there may be at most one master controller at a time. When a controller configures itself as master, any existing master is demoted to the slave role.
slave
Allows the controller read-only access to OpenFlow features. Attempts to modify the flow table will be rejected with an error. Slave controllers do not receive OFPT_PACKET_IN or OFPT_FLOW_REMOVED messages, but they do receive OFPT_PORT_STATUS messages.
A human-readable description of the last error on the connection to the controller; i.e. strerror(errno). This key will exist only if an error has occurred.

The state of the connection to the controller:

VOID
Connection is disabled.
BACKOFF
Attempting to reconnect at an increasing period.
CONNECTING
Attempting to connect.
ACTIVE
Connected, remote host responsive.
IDLE
Connection is idle. Waiting for response to keep-alive.

These values may change in the future. They are provided only for human consumption.

The amount of time since this controller last successfully connected to the switch (in seconds). Value is empty if controller has never successfully connected. The amount of time since this controller last disconnected from the switch (in seconds). Value is empty if controller has never disconnected.

Additional configuration for a connection between the controller and the Open vSwitch.

The Differentiated Service Code Point (DSCP) is specified using 6 bits in the Type of Service (TOS) field in the IP header. DSCP provides a mechanism to classify the network traffic and provide Quality of Service (QoS) on IP networks. The DSCP value specified here is used when establishing the connection between the controller and the Open vSwitch. If no value is specified, a default value of 48 is chosen. Valid DSCP values must be in the range 0 to 63.
The overall purpose of these columns is described under Common Columns at the beginning of this document.

Configuration for a database connection to an Open vSwitch database (OVSDB) client.

This table primarily configures the Open vSwitch database (ovsdb-server), not the Open vSwitch switch (ovs-vswitchd). The switch does read the table to determine what connections should be treated as in-band.

The Open vSwitch database server can initiate and maintain active connections to remote clients. It can also listen for database connections.

Connection method for managers.

The following connection methods are currently supported:

ssl:ip[:port]

The specified SSL port on the host at the given ip, which must be expressed as an IP address (not a DNS name). The column in the table must point to a valid SSL configuration when this form is used.

If port is not specified, it defaults to 6640.

SSL support is an optional feature that is not always built as part of Open vSwitch.

tcp:ip[:port]

The specified TCP port on the host at the given ip, which must be expressed as an IP address (not a DNS name), where ip can be IPv4 or IPv6 address. If ip is an IPv6 address, wrap it in square brackets, e.g. tcp:[::1]:6640.

If port is not specified, it defaults to 6640.

pssl:[port][:ip]

Listens for SSL connections on the specified TCP port. Specify 0 for port to have the kernel automatically choose an available port. If ip, which must be expressed as an IP address (not a DNS name), is specified, then connections are restricted to the specified local IP address (either IPv4 or IPv6 address). If ip is an IPv6 address, wrap in square brackets, e.g. pssl:6640:[::1]. If ip is not specified then it listens only on IPv4 (but not IPv6) addresses. The column in the table must point to a valid SSL configuration when this form is used.

If port is not specified, it defaults to 6640.

SSL support is an optional feature that is not always built as part of Open vSwitch.

ptcp:[port][:ip]

Listens for connections on the specified TCP port. Specify 0 for port to have the kernel automatically choose an available port. If ip, which must be expressed as an IP address (not a DNS name), is specified, then connections are restricted to the specified local IP address (either IPv4 or IPv6 address). If ip is an IPv6 address, wrap it in square brackets, e.g. ptcp:6640:[::1]. If ip is not specified then it listens only on IPv4 addresses.

If port is not specified, it defaults to 6640.

When multiple managers are configured, the values must be unique. Duplicate values yield unspecified results.

If it is specified, this setting must be one of the following strings that describes how Open vSwitch contacts this OVSDB client over the network:

in-band
In this mode, this connection's traffic travels over a bridge managed by Open vSwitch. With this setting, Open vSwitch allows traffic to and from the client regardless of the contents of the OpenFlow flow table. (Otherwise, Open vSwitch would never be able to connect to the client, because it did not have a flow to enable it.) This is the most common connection mode because it is not necessary to maintain two independent networks.
out-of-band
In this mode, the client's traffic uses a control network separate from that managed by Open vSwitch, that is, Open vSwitch does not use any of its own network devices to communicate with the client. The control network must be configured separately, before or after ovs-vswitchd is started.

If not specified, the default is implementation-specific.

Maximum number of milliseconds to wait between connection attempts. Default is implementation-specific. Maximum number of milliseconds of idle time on connection to the client before sending an inactivity probe message. If Open vSwitch does not communicate with the client for the specified number of seconds, it will send a probe. If a response is not received for the same additional amount of time, Open vSwitch assumes the connection has been broken and attempts to reconnect. Default is implementation-specific. A value of 0 disables inactivity probes. true if currently connected to this manager, false otherwise. A human-readable description of the last error on the connection to the manager; i.e. strerror(errno). This key will exist only if an error has occurred.

The state of the connection to the manager:

VOID
Connection is disabled.
BACKOFF
Attempting to reconnect at an increasing period.
CONNECTING
Attempting to connect.
ACTIVE
Connected, remote host responsive.
IDLE
Connection is idle. Waiting for response to keep-alive.

These values may change in the future. They are provided only for human consumption.

The amount of time since this manager last successfully connected to the database (in seconds). Value is empty if manager has never successfully connected. The amount of time since this manager last disconnected from the database (in seconds). Value is empty if manager has never disconnected. Space-separated list of the names of OVSDB locks that the connection holds. Omitted if the connection does not hold any locks. Space-separated list of the names of OVSDB locks that the connection is currently waiting to acquire. Omitted if the connection is not waiting for any locks. Space-separated list of the names of OVSDB locks that the connection has had stolen by another OVSDB client. Omitted if no locks have been stolen from this connection.

When specifies a connection method that listens for inbound connections (e.g. ptcp: or pssl:) and more than one connection is actually active, the value is the number of active connections. Otherwise, this key-value pair is omitted.

When multiple connections are active, status columns and key-value pairs (other than this one) report the status of one arbitrarily chosen connection.

When is ptcp: or pssl:, this is the TCP port on which the OVSDB server is listening. (This is is particularly useful when specifies a port of 0, allowing the kernel to choose any available port.)

Additional configuration for a connection between the manager and the Open vSwitch Database.

The Differentiated Service Code Point (DSCP) is specified using 6 bits in the Type of Service (TOS) field in the IP header. DSCP provides a mechanism to classify the network traffic and provide Quality of Service (QoS) on IP networks. The DSCP value specified here is used when establishing the connection between the manager and the Open vSwitch. If no value is specified, a default value of 48 is chosen. Valid DSCP values must be in the range 0 to 63.
The overall purpose of these columns is described under Common Columns at the beginning of this document.
A NetFlow target. NetFlow is a protocol that exports a number of details about terminating IP flows, such as the principals involved and duration. NetFlow targets in the form ip:port. The ip must be specified numerically, not as a DNS name. Engine ID to use in NetFlow messages. Defaults to datapath index if not specified. Engine type to use in NetFlow messages. Defaults to datapath index if not specified.

The interval at which NetFlow records are sent for flows that are still active, in seconds. A value of 0 requests the default timeout (currently 600 seconds); a value of -1 disables active timeouts.

The NetFlow passive timeout, for flows that become inactive, is not configurable. It will vary depending on the Open vSwitch version, the forms and contents of the OpenFlow flow tables, CPU and memory usage, and network activity. A typical passive timeout is about a second.

If this column's value is false, the ingress and egress interface fields of NetFlow flow records are derived from OpenFlow port numbers. When it is true, the 7 most significant bits of these fields will be replaced by the least significant 7 bits of the engine id. This is useful because many NetFlow collectors do not expect multiple switches to be sending messages from the same host, so they do not store the engine information which could be used to disambiguate the traffic.

When this option is enabled, a maximum of 508 ports are supported.

The overall purpose of these columns is described under Common Columns at the beginning of this document.
SSL configuration for an Open_vSwitch. Name of a PEM file containing the private key used as the switch's identity for SSL connections to the controller. Name of a PEM file containing a certificate, signed by the certificate authority (CA) used by the controller and manager, that certifies the switch's private key, identifying a trustworthy switch. Name of a PEM file containing the CA certificate used to verify that the switch is connected to a trustworthy controller. If set to true, then Open vSwitch will attempt to obtain the CA certificate from the controller on its first SSL connection and save it to the named PEM file. If it is successful, it will immediately drop the connection and reconnect, and from then on all SSL connections must be authenticated by a certificate signed by the CA certificate thus obtained. This option exposes the SSL connection to a man-in-the-middle attack obtaining the initial CA certificate. It may still be useful for bootstrapping. The overall purpose of these columns is described under Common Columns at the beginning of this document.

A set of sFlow(R) targets. sFlow is a protocol for remote monitoring of switches.

Name of the network device whose IP address should be reported as the ``agent address'' to collectors. If not specified, the agent device is figured from the first target address and the routing table. If the routing table does not contain a route to the target, the IP address defaults to the in the collector's . If an agent IP address cannot be determined any of these ways, sFlow is disabled. Number of bytes of a sampled packet to send to the collector. If not specified, the default is 128 bytes. Polling rate in seconds to send port statistics to the collector. If not specified, defaults to 30 seconds. Rate at which packets should be sampled and sent to the collector. If not specified, defaults to 400, which means one out of 400 packets, on average, will be sent to the collector. sFlow targets in the form ip:port. The overall purpose of these columns is described under Common Columns at the beginning of this document.

Configuration for sending packets to IPFIX collectors.

IPFIX is a protocol that exports a number of details about flows. The IPFIX implementation in Open vSwitch samples packets at a configurable rate, extracts flow information from those packets, optionally caches and aggregates the flow information, and sends the result to one or more collectors.

IPFIX in Open vSwitch can be configured two different ways:

IPFIX target collectors in the form ip:port. The maximum period in seconds for which an IPFIX flow record is cached and aggregated before being sent. If not specified, defaults to 0. If 0, caching is disabled. The maximum number of IPFIX flow records that can be cached at a time. If not specified, defaults to 0. If 0, caching is disabled.

These values affect only per-bridge sampling. See above for a description of the differences between per-bridge and flow-based sampling.

The rate at which packets should be sampled and sent to each target collector. If not specified, defaults to 400, which means one out of 400 packets, on average, will be sent to each target collector. The IPFIX Observation Domain ID sent in each IPFIX packet. If not specified, defaults to 0. The IPFIX Observation Point ID sent in each IPFIX flow record. If not specified, defaults to 0.

Set to true to enable sampling and reporting tunnel header 7-tuples in IPFIX flow records. Tunnel sampling is disabled by default.

The following enterprise entities report the sampled tunnel info:

tunnelType:

ID: 891, and enterprise ID 6876 (VMware).

type: unsigned 8-bit integer.

data type semantics: identifier.

description: Identifier of the layer 2 network overlay network encapsulation type: 0x01 VxLAN, 0x02 GRE, 0x03 LISP, 0x05 IPsec+GRE, 0x07 GENEVE.

tunnelKey:

ID: 892, and enterprise ID 6876 (VMware).

type: variable-length octetarray.

data type semantics: identifier.

description: Key which is used for identifying an individual traffic flow within a VxLAN (24-bit VNI), GENEVE (24-bit VNI), GRE (32- or 64-bit key), or LISP (24-bit instance ID) tunnel. The key is encoded in this octetarray as a 3-, 4-, or 8-byte integer ID in network byte order.

tunnelSourceIPv4Address:

ID: 893, and enterprise ID 6876 (VMware).

type: unsigned 32-bit integer.

data type semantics: identifier.

description: The IPv4 source address in the tunnel IP packet header.

tunnelDestinationIPv4Address:

ID: 894, and enterprise ID 6876 (VMware).

type: unsigned 32-bit integer.

data type semantics: identifier.

description: The IPv4 destination address in the tunnel IP packet header.

tunnelProtocolIdentifier:

ID: 895, and enterprise ID 6876 (VMware).

type: unsigned 8-bit integer.

data type semantics: identifier.

description: The value of the protocol number in the tunnel IP packet header. The protocol number identifies the tunnel IP packet payload type.

tunnelSourceTransportPort:

ID: 896, and enterprise ID 6876 (VMware).

type: unsigned 16-bit integer.

data type semantics: identifier.

description: The source port identifier in the tunnel transport header. For the transport protocols UDP, TCP, and SCTP, this is the source port number given in the respective header.

tunnelDestinationTransportPort:

ID: 897, and enterprise ID 6876 (VMware).

type: unsigned 16-bit integer.

data type semantics: identifier.

description: The destination port identifier in the tunnel transport header. For the transport protocols UDP, TCP, and SCTP, this is the destination port number given in the respective header.

By default, Open vSwitch samples and reports flows at bridge port input in IPFIX flow records. Set this column to false to disable input sampling. By default, Open vSwitch samples and reports flows at bridge port output in IPFIX flow records. Set this column to false to disable output sampling.
The overall purpose of these columns is described under Common Columns at the beginning of this document.

A set of IPFIX collectors of packet samples generated by OpenFlow sample actions. This table is used only for IPFIX flow-based sampling, not for per-bridge sampling (see the table for a description of the two forms).

The ID of this collector set, unique among the bridge's collector sets, to be used as the collector_set_id in OpenFlow sample actions. The bridge into which OpenFlow sample actions can be added to send packet samples to this set of IPFIX collectors. Configuration of the set of IPFIX collectors to send one flow record per sampled packet to. The overall purpose of these columns is described under Common Columns at the beginning of this document.

Auto Attach configuration within a bridge. The IETF Auto-Attach SPBM draft standard describes a compact method of using IEEE 802.1AB Link Layer Discovery Protocol (LLDP) together with a IEEE 802.1aq Shortest Path Bridging (SPB) network to automatically attach network devices to individual services in a SPB network. The intent here is to allow network applications and devices using OVS to be able to easily take advantage of features offered by industry standard SPB networks.

Auto Attach (AA) uses LLDP to communicate between a directly connected Auto Attach Client (AAC) and Auto Attach Server (AAS). The LLDP protocol is extended to add two new Type-Length-Value tuples (TLVs). The first new TLV supports the ongoing discovery of directly connected AA correspondents. Auto Attach operates by regularly transmitting AA discovery TLVs between the AA client and AA server. By exchanging these discovery messages, both the AAC and AAS learn the system name and system description of their peer. In the OVS context, OVS operates as the AA client and the AA server resides on a switch at the edge of the SPB network.

Once AA discovery has been completed the AAC then uses the second new TLV to deliver identifier mappings from the AAC to the AAS. A primary feature of Auto Attach is to facilitate the mapping of VLANs defined outside the SPB network onto service ids (ISIDs) defined within the SPM network. By doing so individual external VLANs can be mapped onto specific SPB network services. These VLAN id to ISID mappings can be configured and managed locally using new options added to the ovs-vsctl command.

The Auto Attach OVS feature does not provide a full implementation of the LLDP protocol. Support for the mandatory TLVs as defined by the LLDP standard and support for the AA TLV extensions is provided. LLDP protocol support in OVS can be enabled or disabled on a port by port basis. LLDP support is disabled by default.

The system_name string is exported in LLDP messages. It should uniquely identify the bridge in the network. The system_description string is exported in LLDP messages. It should describe the type of software and hardware. A mapping from SPB network Individual Service Identifier (ISID) to VLAN id.