5 files changed, 3357 insertions, 3357 deletions

diff --git a/README.dos b/README.dos
index 8d42f65e98..51cd1d6f18 100644
--- a/README.dos
+++ b/README.dos
@@ -1,215 +1,215 @@
-If you read this file _as_is_, just ignore the funny characters you

-see. It is written in the POD format (see perlpod manpage) which is

-specially designed to be readable as is.

-

-=head1 NAME

-

-perldos - Perl under DOS, W31, W95.

-

-=head1 SYNOPSIS

-

-These are instructions for building Perl under DOS (or w??), using

-DJGPP v2.01 or later. Under w95 long filenames are supported.

-

-=head1 DESCRIPTION

-

-Before you start, you should glance through the README file

-found in the top-level directory where the Perl distribution

-was extracted.  Make sure you read and understand the terms under

-which this software is being distributed.

-

-This port currently supports MakeMaker (the set of modules that

-is used to build extensions to perl).  Therefore, you should be

-able to build and install most extensions found in the CPAN sites.

-

-=head2 Prerequisites

-

-=over 4

-

-=item DJGPP

-

-DJGPP is a port of GNU C/C++ compiler and development tools to 32-bit,

-protected-mode environment on Intel 32-bit CPUs running MS-DOS and compatible

-operating systems, by DJ Delorie <dj@delorie.com> and friends.

-

-For more details (FAQ), check out the home of DJGPP at:

-

-        http://www.delorie.com/djgpp/

-

-If you have questions about DJGPP, try posting to the DJGPP newsgroup:

-comp.os.msdos.djgpp, or use the email gateway djgpp@delorie.com.

-

-You can find the full DJGPP distribution on any SimTel.Net mirror all over

-the world. Like:

-

-        ftp://ftp.simtel.net/pub/simtelnet/gnu/djgpp/v2*

-

-You need the following files to build perl (or add new modules):

-

-        v2/djdev202.zip

-        v2/bnu27b.zip

-        v2gnu/gcc2721b.zip

-        v2gnu/bsh1147b.zip

-        v2gnu/mak3761b.zip

-        v2gnu/fil316b.zip

-        v2gnu/sed118b.zip

-        v2gnu/txt122b.zip

-        v2gnu/dif271b.zip

-        v2gnu/grep21b.zip

-        v2gnu/shl112b.zip

-        v2gnu/gawk303b.zip

-        v2misc/csdpmi4b.zip 

-

-or possibly any newer version.

-

-=item Pthreads

-

-Thread support is not tested in this version of the djgpp perl.

-

-=back

-

-=head2 Shortcomings of Perl under DOS

-

-Perl under DOS lacks some features of perl under UNIX because of

-deficiencies in the UNIX-emulation, most notably:

-

-=over 4

-

-=item *

-

-fork() and pipe()

-

-=item *

-

-some features of the UNIX filesystem regarding link count and file dates

-

-=item *

-

-in-place operation is a little bit broken with short filenames

-

-=item *

-

-sockets

-

-=back

-

-=head2 Building

-

-=over 4

-

-=item *

-

-Unpack the source package F<perl5.6*.tar.gz> with djtarx. If you want

-to use long file names under w95 and also to get Perl to pass all its

-tests, don't forget to use

-

-        set LFN=y

-	set FNCASE=y

-

-before unpacking the archive.

-

-=item *

-

-Create a "symlink" or copy your bash.exe to sh.exe in your C<($DJDIR)/bin>

-directory.

-

-        ln -s bash.exe sh.exe

-

-And make the C<SHELL> environment variable point to this F<sh.exe>:

-

-        set SHELL=c:/djgpp/bin/sh.exe (use full path name!)

-

-You can do this in F<djgpp.env> too. Add this line BEFORE any section

-definition:

-

-        +SHELL=%DJDIR%/bin/sh.exe

-

-=item *

-

-If you have F<split.exe> and F<gsplit.exe> in your path, then rename 

-F<split.exe> to F<djsplit.exe>, and F<gsplit.exe> to F<split.exe>.

-Copy or link F<gecho.exe> to F<echo.exe> if you don't have F<echo.exe>.

-Copy or link F<gawk.exe> to F<awk.exe> if you don't have F<awk.exe>.

-

-=item *

-

-Chdir to the djgpp subdirectory of perl toplevel and type the following

-command:

-

-        configure.bat

-

-This will do some preprocessing then run the Configure script for you.

-The Configure script is interactive, but in most cases you

-just need to press ENTER.

-

-If the script says that your package is incomplete, and asks whether

-to continue, just answer with Y (this can only happen if you don't use

-long filenames).

-

-When Configure asks about the extensions, I suggest IO and Fcntl,

-and if you want database handling then SDBM_File or GDBM_File

-(you need to install gdbm for this one). If you want to use the

-POSIX extension (this is the default), make sure that the stack

-size of your F<cc1.exe> is at least 512kbyte (you can check this

-with: C<stubedit cc1.exe>).

-

-You can use the Configure script in non-interactive mode too.

-When I built my F<perl.exe>, I used something like this:

-

-        configure.bat -des

-

-You can find more info about Configure's command line switches in

-the F<INSTALL> file.

-

-When the script ends, and you want to change some values in the

-generated F<config.sh> file, then run

-

-        sh Configure -S

-

-after you made your modifications.

-

-IMPORTANT: if you use this C<-S> switch, be sure to delete the CONFIG

-environment variable before running the script:

-

-        set CONFIG=

-

-=item *

-

-Now you can compile Perl. Type:

-

-        make

-

-=back

-

-=head2 Testing

-

-Type:

-

-        make test

-

-If you're lucky you should see "All tests successful". But there can be

-a few failed subtests (less than 5 hopefully) depending on some external

-conditions (e.g. some subtests fail under linux/dosemu or plain dos

-with short filenames only).

-

-=head2 Installation

-

-Type:

-

-        make install

-

-This will copy the newly compiled perl and libraries into your DJGPP

-directory structure. Perl.exe and the utilities go into C<($DJDIR)/bin>,

-and the library goes under C<($DJDIR)/lib/perl5>. The pod documentation

-goes under C<($DJDIR)/lib/perl5/pod>.

-

-=head1 AUTHOR

-

-Laszlo Molnar, F<laszlo.molnar@eth.ericsson.se>

-

-=head1 SEE ALSO

-

-perl(1).

-

-=cut

-

+If you read this file _as_is_, just ignore the funny characters you
+see. It is written in the POD format (see perlpod manpage) which is
+specially designed to be readable as is.
+
+=head1 NAME
+
+perldos - Perl under DOS, W31, W95.
+
+=head1 SYNOPSIS
+
+These are instructions for building Perl under DOS (or w??), using
+DJGPP v2.01 or later. Under w95 long filenames are supported.
+
+=head1 DESCRIPTION
+
+Before you start, you should glance through the README file
+found in the top-level directory where the Perl distribution
+was extracted.  Make sure you read and understand the terms under
+which this software is being distributed.
+
+This port currently supports MakeMaker (the set of modules that
+is used to build extensions to perl).  Therefore, you should be
+able to build and install most extensions found in the CPAN sites.
+
+=head2 Prerequisites
+
+=over 4
+
+=item DJGPP
+
+DJGPP is a port of GNU C/C++ compiler and development tools to 32-bit,
+protected-mode environment on Intel 32-bit CPUs running MS-DOS and compatible
+operating systems, by DJ Delorie <dj@delorie.com> and friends.
+
+For more details (FAQ), check out the home of DJGPP at:
+
+        http://www.delorie.com/djgpp/
+
+If you have questions about DJGPP, try posting to the DJGPP newsgroup:
+comp.os.msdos.djgpp, or use the email gateway djgpp@delorie.com.
+
+You can find the full DJGPP distribution on any SimTel.Net mirror all over
+the world. Like:
+
+        ftp://ftp.simtel.net/pub/simtelnet/gnu/djgpp/v2*
+
+You need the following files to build perl (or add new modules):
+
+        v2/djdev202.zip
+        v2/bnu27b.zip
+        v2gnu/gcc2721b.zip
+        v2gnu/bsh1147b.zip
+        v2gnu/mak3761b.zip
+        v2gnu/fil316b.zip
+        v2gnu/sed118b.zip
+        v2gnu/txt122b.zip
+        v2gnu/dif271b.zip
+        v2gnu/grep21b.zip
+        v2gnu/shl112b.zip
+        v2gnu/gawk303b.zip
+        v2misc/csdpmi4b.zip 
+
+or possibly any newer version.
+
+=item Pthreads
+
+Thread support is not tested in this version of the djgpp perl.
+
+=back
+
+=head2 Shortcomings of Perl under DOS
+
+Perl under DOS lacks some features of perl under UNIX because of
+deficiencies in the UNIX-emulation, most notably:
+
+=over 4
+
+=item *
+
+fork() and pipe()
+
+=item *
+
+some features of the UNIX filesystem regarding link count and file dates
+
+=item *
+
+in-place operation is a little bit broken with short filenames
+
+=item *
+
+sockets
+
+=back
+
+=head2 Building
+
+=over 4
+
+=item *
+
+Unpack the source package F<perl5.6*.tar.gz> with djtarx. If you want
+to use long file names under w95 and also to get Perl to pass all its
+tests, don't forget to use
+
+        set LFN=y
+	set FNCASE=y
+
+before unpacking the archive.
+
+=item *
+
+Create a "symlink" or copy your bash.exe to sh.exe in your C<($DJDIR)/bin>
+directory.
+
+        ln -s bash.exe sh.exe
+
+And make the C<SHELL> environment variable point to this F<sh.exe>:
+
+        set SHELL=c:/djgpp/bin/sh.exe (use full path name!)
+
+You can do this in F<djgpp.env> too. Add this line BEFORE any section
+definition:
+
+        +SHELL=%DJDIR%/bin/sh.exe
+
+=item *
+
+If you have F<split.exe> and F<gsplit.exe> in your path, then rename 
+F<split.exe> to F<djsplit.exe>, and F<gsplit.exe> to F<split.exe>.
+Copy or link F<gecho.exe> to F<echo.exe> if you don't have F<echo.exe>.
+Copy or link F<gawk.exe> to F<awk.exe> if you don't have F<awk.exe>.
+
+=item *
+
+Chdir to the djgpp subdirectory of perl toplevel and type the following
+command:
+
+        configure.bat
+
+This will do some preprocessing then run the Configure script for you.
+The Configure script is interactive, but in most cases you
+just need to press ENTER.
+
+If the script says that your package is incomplete, and asks whether
+to continue, just answer with Y (this can only happen if you don't use
+long filenames).
+
+When Configure asks about the extensions, I suggest IO and Fcntl,
+and if you want database handling then SDBM_File or GDBM_File
+(you need to install gdbm for this one). If you want to use the
+POSIX extension (this is the default), make sure that the stack
+size of your F<cc1.exe> is at least 512kbyte (you can check this
+with: C<stubedit cc1.exe>).
+
+You can use the Configure script in non-interactive mode too.
+When I built my F<perl.exe>, I used something like this:
+
+        configure.bat -des
+
+You can find more info about Configure's command line switches in
+the F<INSTALL> file.
+
+When the script ends, and you want to change some values in the
+generated F<config.sh> file, then run
+
+        sh Configure -S
+
+after you made your modifications.
+
+IMPORTANT: if you use this C<-S> switch, be sure to delete the CONFIG
+environment variable before running the script:
+
+        set CONFIG=
+
+=item *
+
+Now you can compile Perl. Type:
+
+        make
+
+=back
+
+=head2 Testing
+
+Type:
+
+        make test
+
+If you're lucky you should see "All tests successful". But there can be
+a few failed subtests (less than 5 hopefully) depending on some external
+conditions (e.g. some subtests fail under linux/dosemu or plain dos
+with short filenames only).
+
+=head2 Installation
+
+Type:
+
+        make install
+
+This will copy the newly compiled perl and libraries into your DJGPP
+directory structure. Perl.exe and the utilities go into C<($DJDIR)/bin>,
+and the library goes under C<($DJDIR)/lib/perl5>. The pod documentation
+goes under C<($DJDIR)/lib/perl5/pod>.
+
+=head1 AUTHOR
+
+Laszlo Molnar, F<laszlo.molnar@eth.ericsson.se>
+
+=head1 SEE ALSO
+
+perl(1).
+
+=cut
+
diff --git a/README.win32 b/README.win32
index a0d7a0b678..8e29accdbb 100644
--- a/README.win32
+++ b/README.win32
@@ -1,656 +1,656 @@
-If you read this file _as_is_, just ignore the funny characters you

-see. It is written in the POD format (see pod/perlpod.pod) which is

-specially designed to be readable as is.

-

-=head1 NAME

-

-perlwin32 - Perl under Win32

-

-=head1 SYNOPSIS

-

-These are instructions for building Perl under Windows (9x, NT and

-2000).

-

-=head1 DESCRIPTION

-

-Before you start, you should glance through the README file

-found in the top-level directory where the Perl distribution

-was extracted.  Make sure you read and understand the terms under

-which this software is being distributed.

-

-Also make sure you read L<BUGS AND CAVEATS> below for the

-known limitations of this port.

-

-The INSTALL file in the perl top-level has much information that is

-only relevant to people building Perl on Unix-like systems.  In

-particular, you can safely ignore any information that talks about

-"Configure".

-

-You may also want to look at two other options for building

-a perl that will work on Windows NT:  the README.cygwin and

-README.os2 files, which each give a different set of rules to build

-a Perl that will work on Win32 platforms.  Those two methods will

-probably enable you to build a more Unix-compatible perl, but you

-will also need to download and use various other build-time and

-run-time support software described in those files.

-

-This set of instructions is meant to describe a so-called "native"

-port of Perl to Win32 platforms.  The resulting Perl requires no

-additional software to run (other than what came with your operating

-system).  Currently, this port is capable of using one of the

-following compilers:

-

-      Borland C++		version 5.02 or later

-      Microsoft Visual C++	version 4.2 or later

-      Mingw32 with GCC		version 2.95.2 or better

-

-The last of these is a high quality freeware compiler.  Support

-for it is still experimental.  (Older versions of GCC are known

-not to work.)

-

-This port currently supports MakeMaker (the set of modules that

-is used to build extensions to perl).  Therefore, you should be

-able to build and install most extensions found in the CPAN sites.

-See L<Usage Hints> below for general hints about this.

-

-=head2 Setting Up

-

-=over 4

-

-=item Make

-

-You need a "make" program to build the sources.  If you are using

-Visual C++ under Windows NT or 2000, nmake will work.  All other

-builds need dmake.

-

-dmake is a freely available make that has very nice macro features

-and parallelability.

-

-A port of dmake for Windows is available from:

-

-    http://www.cpan.org/authors/id/GSAR/dmake-4.1pl1-win32.zip

-

-(This is a fixed version of original dmake sources obtained from

-http://www.wticorp.com/dmake/.  As of version 4.1PL1, the original

-sources did not build as shipped, and had various other problems.

-A patch is included in the above fixed version.)

-

-Fetch and install dmake somewhere on your path (follow the instructions

-in the README.NOW file).

-

-=item Command Shell

-

-Use the default "cmd" shell that comes with NT.  Some versions of the

-popular 4DOS/NT shell have incompatibilities that may cause you trouble.

-If the build fails under that shell, try building again with the cmd

-shell.

-

-The nmake Makefile also has known incompatibilities with the

-"command.com" shell that comes with Windows 9x.  You will need to

-use dmake and makefile.mk to build under Windows 9x.

-

-The surest way to build it is on Windows NT, using the cmd shell.

-

-Make sure the path to the build directory does not contain spaces.  The

-build usually works in this circumstance, but some tests will fail.

-

-=item Borland C++

-

-If you are using the Borland compiler, you will need dmake.

-(The make that Borland supplies is seriously crippled, and will not

-work for MakeMaker builds.)

-

-See L/"Make"> above.

-

-=item Microsoft Visual C++

-

-The nmake that comes with Visual C++ will suffice for building.

-You will need to run the VCVARS32.BAT file usually found somewhere

-like C:\MSDEV4.2\BIN.  This will set your build environment.

-

-You can also use dmake to build using Visual C++, provided:

-you set OSRELEASE to "microsft" (or whatever the directory name

-under which the Visual C dmake configuration lives) in your environment,

-and edit win32/config.vc to change "make=nmake" into "make=dmake".  The

-latter step is only essential if you want to use dmake as your default

-make for building extensions using MakeMaker.

-

-=item Mingw32 with GCC

-

-GCC-2.95.2 binaries can be downloaded from:

-

-    ftp://ftp.xraylith.wisc.edu/pub/khan/gnu-win32/mingw32/

-

-The GCC-2.95.2 bundle comes with Mingw32 libraries and headers.

-

-Make sure you install the binaries that work with MSVCRT.DLL as indicated

-in the README for the GCC bundle.  You may need to set up a few environment

-variables (usually run from a batch file).

-

-The version of gcc-2.95.2-msvcrt.exe released 7 November 1999 left out

-a fix for certain command line quotes, so be sure to download and install

-fixes/quote-fix-msvcrt.exe too.

-

-You also need dmake.  See L</"Make"> above on how to get it.

-

-=back

-

-=head2 Building

-

-=over 4

-

-=item *

-

-Make sure you are in the "win32" subdirectory under the perl toplevel.

-This directory contains a "Makefile" that will work with

-versions of nmake that come with Visual C++, and a dmake "makefile.mk"

-that will work for all supported compilers.  The defaults in the dmake

-makefile are setup to build using the GCC compiler.

-

-=item *

-

-Edit the makefile.mk (or Makefile, if using nmake) and change the values

-of INST_DRV and INST_TOP.   You can also enable various build

-flags.  These are explained in the makefiles.

-

-You will have to make sure CCTYPE is set correctly, and CCHOME points

-to wherever you installed your compiler.

-

-The default value for CCHOME in the makefiles for Visual C++

-may not be correct for some versions.  Make sure the default exists

-and is valid.

-

-If you have either the source or a library that contains des_fcrypt(),

-enable the appropriate option in the makefile.  des_fcrypt() is not

-bundled with the distribution due to US Government restrictions

-on the export of cryptographic software.  Nevertheless, this routine

-is part of the "libdes" library (written by Eric Young) which is widely

-available worldwide, usually along with SSLeay (for example:

-"ftp://fractal.mta.ca/pub/crypto/SSLeay/DES/").  Set CRYPT_SRC to the

-name of the file that implements des_fcrypt().  Alternatively, if

-you have built a library that contains des_fcrypt(), you can set

-CRYPT_LIB to point to the library name.  The location above contains

-many versions of the "libdes" library, all with slightly different

-implementations of des_fcrypt().  Older versions have a single,

-self-contained file (fcrypt.c) that implements crypt(), so they may be

-easier to use.  A patch against the fcrypt.c found in libdes-3.06 is

-in des_fcrypt.patch.

-

-Perl will also build without des_fcrypt(), but the crypt() builtin will

-fail at run time.

-

-Be sure to read the instructions near the top of the makefiles carefully.

-

-=item *

-

-Type "dmake" (or "nmake" if you are using that make).

-

-This should build everything.  Specifically, it will create perl.exe,

-perl56.dll at the perl toplevel, and various other extension dll's

-under the lib\auto directory.  If the build fails for any reason, make

-sure you have done the previous steps correctly.

-

-=back

-

-=head2 Testing

-

-Type "dmake test" (or "nmake test").  This will run most of the tests from

-the testsuite (many tests will be skipped).

-

-There should be no test failures when running under Windows NT 4.0 or

-Windows 2000.  Many tests I<will> fail under Windows 9x due to the inferior

-command shell.

-

-Some test failures may occur if you use a command shell other than the

-native "cmd.exe", or if you are building from a path that contains

-spaces.  So don't do that.

-

-If you are running the tests from a emacs shell window, you may see

-failures in op/stat.t.  Run "dmake test-notty" in that case.

-

-If you're using the Borland compiler, you may see a failure in op/taint.t

-arising from the inability to find the Borland Runtime DLLs on the system

-default path.  You will need to copy the DLLs reported by the messages

-from where Borland chose to install it, into the Windows system directory

-(usually somewhere like C:\WINNT\SYSTEM32), and rerun the test.

-

-Please report any other failures as described under L<BUGS AND CAVEATS>.

-

-=head2 Installation

-

-Type "dmake install" (or "nmake install").  This will put the newly

-built perl and the libraries under whatever C<INST_TOP> points to in the

-Makefile.  It will also install the pod documentation under

-C<$INST_TOP\$VERSION\lib\pod> and HTML versions of the same under

-C<$INST_TOP\$VERSION\lib\pod\html>.  To use the Perl you just installed,

-you will need to add two components to your PATH environment variable,

-C<$INST_TOP\$VERSION\bin>, and C<$INST_TOP\$VERSION\bin\$ARCHNAME>.

-For example:

-

-    set PATH c:\perl\5.6.0\bin;c:\perl\5.6.0\bin\MSWin32-x86;%PATH%

-

-If you opt to comment out INST_VER and INST_ARCH in the makefiles, the

-installation structure is much simpler.  In that case, it will be

-sufficient to add a single entry to the path, for instance:

-

-    set PATH c:\perl\bin;%PATH%

-

-=head2 Usage Hints

-

-=over 4

-

-=item Environment Variables

-

-The installation paths that you set during the build get compiled

-into perl, so you don't have to do anything additional to start

-using that perl (except add its location to your PATH variable).

-

-If you put extensions in unusual places, you can set PERL5LIB

-to a list of paths separated by semicolons where you want perl

-to look for libraries.  Look for descriptions of other environment

-variables you can set in L<perlrun>.

-

-You can also control the shell that perl uses to run system() and

-backtick commands via PERL5SHELL.  See L<perlrun>.

-

-Perl does not depend on the registry, but it can look up certain default

-values if you choose to put them there.  Perl attempts to read entries from

-C<HKEY_CURRENT_USER\Software\Perl> and C<HKEY_LOCAL_MACHINE\Software\Perl>.

-Entries in the former override entries in the latter.  One or more of the

-following entries (of type REG_SZ or REG_EXPAND_SZ) may be set:

-

-    lib-$]		version-specific standard library path to add to @INC

-    lib			standard library path to add to @INC

-    sitelib-$]		version-specific site library path to add to @INC

-    sitelib		site library path to add to @INC

-    vendorlib-$]	version-specific vendor library path to add to @INC

-    vendorlib		vendor library path to add to @INC

-    PERL*		fallback for all %ENV lookups that begin with "PERL"

-

-Note the C<$]> in the above is not literal.  Substitute whatever version

-of perl you want to honor that entry, e.g. C<5.6.0>.  Paths must be

-separated with semicolons, as usual on win32.

-

-=item File Globbing

-

-By default, perl handles file globbing using the File::Glob extension,

-which provides portable globbing.

-

-If you want perl to use globbing that emulates the quirks of DOS

-filename conventions, you might want to consider using File::DosGlob

-to override the internal glob() implementation.  See L<File::DosGlob> for

-details.

-

-=item Using perl from the command line

-

-If you are accustomed to using perl from various command-line

-shells found in UNIX environments, you will be less than pleased

-with what Windows offers by way of a command shell.

-

-The crucial thing to understand about the Windows environment is that

-the command line you type in is processed twice before Perl sees it.

-First, your command shell (usually CMD.EXE on Windows NT, and

-COMMAND.COM on Windows 9x) preprocesses the command line, to handle

-redirection, environment variable expansion, and location of the

-executable to run. Then, the perl executable splits the remaining

-command line into individual arguments, using the C runtime library

-upon which Perl was built.

-

-It is particularly important to note that neither the shell nor the C

-runtime do any wildcard expansions of command-line arguments (so

-wildcards need not be quoted).  Also, the quoting behaviours of the

-shell and the C runtime are rudimentary at best (and may, if you are

-using a non-standard shell, be inconsistent).  The only (useful) quote

-character is the double quote (").  It can be used to protect spaces in

-arguments and other special characters.  The Windows NT documentation

-has almost no description of how the quoting rules are implemented, but

-here are some general observations based on experiments:  The C runtime

-breaks arguments at spaces and passes them to programs in argc/argv.

-Doublequotes can be used to prevent arguments with spaces in them from

-being split up.  You can put a double quote in an argument by escaping

-it with a backslash and enclosing the whole argument within double

-quotes.  The backslash and the pair of double quotes surrounding the

-argument will be stripped by the C runtime.

-

-The file redirection characters "<", ">", and "|" can be quoted by

-double quotes (although there are suggestions that this may not always

-be true).  Single quotes are not treated as quotes by the shell or the C

-runtime.  The caret "^" has also been observed to behave as a quoting

-character, but this appears to be a shell feature, and the caret is not

-stripped from the command line, so Perl still sees it (and the C runtime

-phase does not treat the caret as a quote character).

-

-Here are some examples of usage of the "cmd" shell:

-

-This prints two doublequotes:

-

-    perl -e "print '\"\"' "

-

-This does the same:

-

-    perl -e "print \"\\\"\\\"\" "

-

-This prints "bar" and writes "foo" to the file "blurch":

-

-    perl -e "print 'foo'; print STDERR 'bar'" > blurch

-

-This prints "foo" ("bar" disappears into nowhereland):

-

-    perl -e "print 'foo'; print STDERR 'bar'" 2> nul

-

-This prints "bar" and writes "foo" into the file "blurch":

-

-    perl -e "print 'foo'; print STDERR 'bar'" 1> blurch

-

-This pipes "foo" to the "less" pager and prints "bar" on the console:

-

-    perl -e "print 'foo'; print STDERR 'bar'" | less

-

-This pipes "foo\nbar\n" to the less pager:

-

-    perl -le "print 'foo'; print STDERR 'bar'" 2>&1 | less

-

-This pipes "foo" to the pager and writes "bar" in the file "blurch":

-

-    perl -e "print 'foo'; print STDERR 'bar'" 2> blurch | less

-

-

-Discovering the usefulness of the "command.com" shell on Windows 9x

-is left as an exercise to the reader :)

-

-One particularly pernicious problem with the 4NT command shell for

-Windows NT is that it (nearly) always treats a % character as indicating

-that environment variable expansion is needed.  Under this shell, it is

-therefore important to always double any % characters which you want

-Perl to see (for example, for hash variables), even when they are

-quoted.

-

-=item Building Extensions

-

-The Comprehensive Perl Archive Network (CPAN) offers a wealth

-of extensions, some of which require a C compiler to build.

-Look in http://www.cpan.org/ for more information on CPAN.

-

-Note that not all of the extensions available from CPAN may work

-in the Win32 environment; you should check the information at

-http://testers.cpan.org/ before investing too much effort into

-porting modules that don't readily build.

-

-Most extensions (whether they require a C compiler or not) can

-be built, tested and installed with the standard mantra:

-

-    perl Makefile.PL

-    $MAKE

-    $MAKE test

-    $MAKE install

-

-where $MAKE is whatever 'make' program you have configured perl to

-use.  Use "perl -V:make" to find out what this is.  Some extensions

-may not provide a testsuite (so "$MAKE test" may not do anything, or

-fail), but most serious ones do.

-

-It is important that you use a supported 'make' program, and

-ensure Config.pm knows about it.  If you don't have nmake, you can

-either get dmake from the location mentioned earlier, or get an

-old version of nmake reportedly available from:

-

-    ftp://ftp.microsoft.com/Softlib/MSLFILES/nmake15.exe

-

-Another option is to use the make written in Perl, available from

-CPAN:

-

-    http://www.cpan.org/authors/id/NI-S/Make-0.03.tar.gz

-

-You may also use dmake.  See L</"Make"> above on how to get it.

-

-Note that MakeMaker actually emits makefiles with different syntax

-depending on what 'make' it thinks you are using.  Therefore, it is

-important that one of the following values appears in Config.pm:

-

-    make='nmake'	# MakeMaker emits nmake syntax

-    make='dmake'	# MakeMaker emits dmake syntax

-    any other value	# MakeMaker emits generic make syntax

-    			    (e.g GNU make, or Perl make)

-

-If the value doesn't match the 'make' program you want to use,

-edit Config.pm to fix it.

-

-If a module implements XSUBs, you will need one of the supported

-C compilers.  You must make sure you have set up the environment for

-the compiler for command-line compilation.

-

-If a module does not build for some reason, look carefully for

-why it failed, and report problems to the module author.  If

-it looks like the extension building support is at fault, report

-that with full details of how the build failed using the perlbug

-utility.

-

-=item Command-line Wildcard Expansion

-

-The default command shells on DOS descendant operating systems (such

-as they are) usually do not expand wildcard arguments supplied to

-programs.  They consider it the application's job to handle that.

-This is commonly achieved by linking the application (in our case,

-perl) with startup code that the C runtime libraries usually provide.

-However, doing that results in incompatible perl versions (since the

-behavior of the argv expansion code differs depending on the

-compiler, and it is even buggy on some compilers).  Besides, it may

-be a source of frustration if you use such a perl binary with an

-alternate shell that *does* expand wildcards.

-

-Instead, the following solution works rather well. The nice things

-about it: 1) you can start using it right away 2) it is more powerful,

-because it will do the right thing with a pattern like */*/*.c

-3) you can decide whether you do/don't want to use it 4) you can

-extend the method to add any customizations (or even entirely

-different kinds of wildcard expansion).

-

-	C:\> copy con c:\perl\lib\Wild.pm

-	# Wild.pm - emulate shell @ARGV expansion on shells that don't

-	use File::DosGlob;

-	@ARGV = map {

-		      my @g = File::DosGlob::glob($_) if /[*?]/;

-		      @g ? @g : $_;

-		    } @ARGV;

-	1;

-	^Z

-	C:\> set PERL5OPT=-MWild

-	C:\> perl -le "for (@ARGV) { print }" */*/perl*.c

-	p4view/perl/perl.c

-	p4view/perl/perlio.c

-	p4view/perl/perly.c

-	perl5.005/win32/perlglob.c

-	perl5.005/win32/perllib.c

-	perl5.005/win32/perlglob.c

-	perl5.005/win32/perllib.c

-	perl5.005/win32/perlglob.c

-	perl5.005/win32/perllib.c

-

-Note there are two distinct steps there: 1) You'll have to create

-Wild.pm and put it in your perl lib directory. 2) You'll need to

-set the PERL5OPT environment variable.  If you want argv expansion

-to be the default, just set PERL5OPT in your default startup

-environment.

-

-If you are using the Visual C compiler, you can get the C runtime's

-command line wildcard expansion built into perl binary.  The resulting

-binary will always expand unquoted command lines, which may not be

-what you want if you use a shell that does that for you.  The expansion

-done is also somewhat less powerful than the approach suggested above.

-

-=item Win32 Specific Extensions

-

-A number of extensions specific to the Win32 platform are available

-from CPAN.  You may find that many of these extensions are meant to

-be used under the Activeware port of Perl, which used to be the only

-native port for the Win32 platform.  Since the Activeware port does not

-have adequate support for Perl's extension building tools, these

-extensions typically do not support those tools either, and therefore

-cannot be built using the generic steps shown in the previous section.

-

-To ensure smooth transitioning of existing code that uses the

-ActiveState port, there is a bundle of Win32 extensions that contains

-all of the ActiveState extensions and most other Win32 extensions from

-CPAN in source form, along with many added bugfixes, and with MakeMaker

-support.  This bundle is available at:

-

-   http://www.cpan.org/authors/id/GSAR/libwin32-0.151.zip

-

-See the README in that distribution for building and installation

-instructions.  Look for later versions that may be available at the

-same location.

-

-=item Running Perl Scripts

-

-Perl scripts on UNIX use the "#!" (a.k.a "shebang") line to

-indicate to the OS that it should execute the file using perl.

-Win32 has no comparable means to indicate arbitrary files are

-executables.

-

-Instead, all available methods to execute plain text files on

-Win32 rely on the file "extension".  There are three methods

-to use this to execute perl scripts:

-

-=over 8

-

-=item 1

-

-There is a facility called "file extension associations" that will

-work in Windows NT 4.0.  This can be manipulated via the two

-commands "assoc" and "ftype" that come standard with Windows NT

-4.0.  Type "ftype /?" for a complete example of how to set this

-up for perl scripts (Say what?  You thought Windows NT wasn't

-perl-ready? :).

-

-=item 2

-

-Since file associations don't work everywhere, and there are

-reportedly bugs with file associations where it does work, the

-old method of wrapping the perl script to make it look like a

-regular batch file to the OS, may be used.  The install process

-makes available the "pl2bat.bat" script which can be used to wrap

-perl scripts into batch files.  For example:

-

-	pl2bat foo.pl

-

-will create the file "FOO.BAT".  Note "pl2bat" strips any

-.pl suffix and adds a .bat suffix to the generated file.

-

-If you use the 4DOS/NT or similar command shell, note that

-"pl2bat" uses the "%*" variable in the generated batch file to

-refer to all the command line arguments, so you may need to make

-sure that construct works in batch files.  As of this writing,

-4DOS/NT users will need a "ParameterChar = *" statement in their

-4NT.INI file, or will need to execute "setdos /p*" in the 4DOS/NT

-startup file to enable this to work.

-

-=item 3

-

-Using "pl2bat" has a few problems:  the file name gets changed,

-so scripts that rely on C<$0> to find what they must do may not

-run properly; running "pl2bat" replicates the contents of the

-original script, and so this process can be maintenance intensive

-if the originals get updated often.  A different approach that

-avoids both problems is possible.

-

-A script called "runperl.bat" is available that can be copied

-to any filename (along with the .bat suffix).  For example,

-if you call it "foo.bat", it will run the file "foo" when it is

-executed.  Since you can run batch files on Win32 platforms simply

-by typing the name (without the extension), this effectively

-runs the file "foo", when you type either "foo" or "foo.bat".

-With this method, "foo.bat" can even be in a different location

-than the file "foo", as long as "foo" is available somewhere on

-the PATH.  If your scripts are on a filesystem that allows symbolic

-links, you can even avoid copying "runperl.bat".

-

-Here's a diversion:  copy "runperl.bat" to "runperl", and type

-"runperl".  Explain the observed behavior, or lack thereof. :)

-Hint: .gnidnats llits er'uoy fi ,"lrepnur" eteled :tniH

-

-=back

-

-=item Miscellaneous Things

-

-A full set of HTML documentation is installed, so you should be

-able to use it if you have a web browser installed on your

-system.

-

-C<perldoc> is also a useful tool for browsing information contained

-in the documentation, especially in conjunction with a pager

-like C<less> (recent versions of which have Win32 support).  You may

-have to set the PAGER environment variable to use a specific pager.

-"perldoc -f foo" will print information about the perl operator

-"foo".

-

-If you find bugs in perl, you can run C<perlbug> to create a

-bug report (you may have to send it manually if C<perlbug> cannot

-find a mailer on your system).

-

-=back

-

-=head1 BUGS AND CAVEATS

-

-Some of the built-in functions do not act exactly as documented in

-L<perlfunc>, and a few are not implemented at all.  To avoid

-surprises, particularly if you have had prior exposure to Perl

-in other operating environments or if you intend to write code

-that will be portable to other environments, see L<perlport>

-for a reasonably definitive list of these differences.

-

-Not all extensions available from CPAN may build or work properly

-in the Win32 environment.  See L</"Building Extensions">.

-

-Most C<socket()> related calls are supported, but they may not

-behave as on Unix platforms.  See L<perlport> for the full list.

-

-Signal handling may not behave as on Unix platforms (where it

-doesn't exactly "behave", either :).  For instance, calling C<die()>

-or C<exit()> from signal handlers will cause an exception, since most

-implementations of C<signal()> on Win32 are severely crippled.

-Thus, signals may work only for simple things like setting a flag

-variable in the handler.  Using signals under this port should

-currently be considered unsupported.

-

-Please send detailed descriptions of any problems and solutions that 

-you may find to <F<perlbug@perl.com>>, along with the output produced

-by C<perl -V>.

-

-=head1 AUTHORS

-

-=over 4

-

-Gary Ng E<lt>71564.1743@CompuServe.COME<gt>

-

-Gurusamy Sarathy E<lt>gsar@activestate.comE<gt>

-

-Nick Ing-Simmons E<lt>nick@ni-s.u-net.comE<gt>

-

-=back

-

-This document is maintained by Gurusamy Sarathy.

-

-=head1 SEE ALSO

-

-L<perl>

-

-=head1 HISTORY

-

-This port was originally contributed by Gary Ng around 5.003_24,

-and borrowed from the Hip Communications port that was available

-at the time.  Various people have made numerous and sundry hacks

-since then.

-

-Borland support was added in 5.004_01 (Gurusamy Sarathy).

-

-GCC/mingw32 support was added in 5.005 (Nick Ing-Simmons).

-

-Support for PERL_OBJECT was added in 5.005 (ActiveState Tool Corp).

-

-Support for fork() emulation was added in 5.6 (ActiveState Tool Corp).

-

-Win9x support was added in 5.6 (Benjamin Stuhl).

-

-Last updated: 22 March 2000

-

-=cut

+If you read this file _as_is_, just ignore the funny characters you
+see. It is written in the POD format (see pod/perlpod.pod) which is
+specially designed to be readable as is.
+
+=head1 NAME
+
+perlwin32 - Perl under Win32
+
+=head1 SYNOPSIS
+
+These are instructions for building Perl under Windows (9x, NT and
+2000).
+
+=head1 DESCRIPTION
+
+Before you start, you should glance through the README file
+found in the top-level directory where the Perl distribution
+was extracted.  Make sure you read and understand the terms under
+which this software is being distributed.
+
+Also make sure you read L<BUGS AND CAVEATS> below for the
+known limitations of this port.
+
+The INSTALL file in the perl top-level has much information that is
+only relevant to people building Perl on Unix-like systems.  In
+particular, you can safely ignore any information that talks about
+"Configure".
+
+You may also want to look at two other options for building
+a perl that will work on Windows NT:  the README.cygwin and
+README.os2 files, which each give a different set of rules to build
+a Perl that will work on Win32 platforms.  Those two methods will
+probably enable you to build a more Unix-compatible perl, but you
+will also need to download and use various other build-time and
+run-time support software described in those files.
+
+This set of instructions is meant to describe a so-called "native"
+port of Perl to Win32 platforms.  The resulting Perl requires no
+additional software to run (other than what came with your operating
+system).  Currently, this port is capable of using one of the
+following compilers:
+
+      Borland C++		version 5.02 or later
+      Microsoft Visual C++	version 4.2 or later
+      Mingw32 with GCC		version 2.95.2 or better
+
+The last of these is a high quality freeware compiler.  Support
+for it is still experimental.  (Older versions of GCC are known
+not to work.)
+
+This port currently supports MakeMaker (the set of modules that
+is used to build extensions to perl).  Therefore, you should be
+able to build and install most extensions found in the CPAN sites.
+See L<Usage Hints> below for general hints about this.
+
+=head2 Setting Up
+
+=over 4
+
+=item Make
+
+You need a "make" program to build the sources.  If you are using
+Visual C++ under Windows NT or 2000, nmake will work.  All other
+builds need dmake.
+
+dmake is a freely available make that has very nice macro features
+and parallelability.
+
+A port of dmake for Windows is available from:
+
+    http://www.cpan.org/authors/id/GSAR/dmake-4.1pl1-win32.zip
+
+(This is a fixed version of original dmake sources obtained from
+http://www.wticorp.com/dmake/.  As of version 4.1PL1, the original
+sources did not build as shipped, and had various other problems.
+A patch is included in the above fixed version.)
+
+Fetch and install dmake somewhere on your path (follow the instructions
+in the README.NOW file).
+
+=item Command Shell
+
+Use the default "cmd" shell that comes with NT.  Some versions of the
+popular 4DOS/NT shell have incompatibilities that may cause you trouble.
+If the build fails under that shell, try building again with the cmd
+shell.
+
+The nmake Makefile also has known incompatibilities with the
+"command.com" shell that comes with Windows 9x.  You will need to
+use dmake and makefile.mk to build under Windows 9x.
+
+The surest way to build it is on Windows NT, using the cmd shell.
+
+Make sure the path to the build directory does not contain spaces.  The
+build usually works in this circumstance, but some tests will fail.
+
+=item Borland C++
+
+If you are using the Borland compiler, you will need dmake.
+(The make that Borland supplies is seriously crippled, and will not
+work for MakeMaker builds.)
+
+See L/"Make"> above.
+
+=item Microsoft Visual C++
+
+The nmake that comes with Visual C++ will suffice for building.
+You will need to run the VCVARS32.BAT file usually found somewhere
+like C:\MSDEV4.2\BIN.  This will set your build environment.
+
+You can also use dmake to build using Visual C++, provided:
+you set OSRELEASE to "microsft" (or whatever the directory name
+under which the Visual C dmake configuration lives) in your environment,
+and edit win32/config.vc to change "make=nmake" into "make=dmake".  The
+latter step is only essential if you want to use dmake as your default
+make for building extensions using MakeMaker.
+
+=item Mingw32 with GCC
+
+GCC-2.95.2 binaries can be downloaded from:
+
+    ftp://ftp.xraylith.wisc.edu/pub/khan/gnu-win32/mingw32/
+
+The GCC-2.95.2 bundle comes with Mingw32 libraries and headers.
+
+Make sure you install the binaries that work with MSVCRT.DLL as indicated
+in the README for the GCC bundle.  You may need to set up a few environment
+variables (usually run from a batch file).
+
+The version of gcc-2.95.2-msvcrt.exe released 7 November 1999 left out
+a fix for certain command line quotes, so be sure to download and install
+fixes/quote-fix-msvcrt.exe too.
+
+You also need dmake.  See L</"Make"> above on how to get it.
+
+=back
+
+=head2 Building
+
+=over 4
+
+=item *
+
+Make sure you are in the "win32" subdirectory under the perl toplevel.
+This directory contains a "Makefile" that will work with
+versions of nmake that come with Visual C++, and a dmake "makefile.mk"
+that will work for all supported compilers.  The defaults in the dmake
+makefile are setup to build using the GCC compiler.
+
+=item *
+
+Edit the makefile.mk (or Makefile, if using nmake) and change the values
+of INST_DRV and INST_TOP.   You can also enable various build
+flags.  These are explained in the makefiles.
+
+You will have to make sure CCTYPE is set correctly, and CCHOME points
+to wherever you installed your compiler.
+
+The default value for CCHOME in the makefiles for Visual C++
+may not be correct for some versions.  Make sure the default exists
+and is valid.
+
+If you have either the source or a library that contains des_fcrypt(),
+enable the appropriate option in the makefile.  des_fcrypt() is not
+bundled with the distribution due to US Government restrictions
+on the export of cryptographic software.  Nevertheless, this routine
+is part of the "libdes" library (written by Eric Young) which is widely
+available worldwide, usually along with SSLeay (for example:
+"ftp://fractal.mta.ca/pub/crypto/SSLeay/DES/").  Set CRYPT_SRC to the
+name of the file that implements des_fcrypt().  Alternatively, if
+you have built a library that contains des_fcrypt(), you can set
+CRYPT_LIB to point to the library name.  The location above contains
+many versions of the "libdes" library, all with slightly different
+implementations of des_fcrypt().  Older versions have a single,
+self-contained file (fcrypt.c) that implements crypt(), so they may be
+easier to use.  A patch against the fcrypt.c found in libdes-3.06 is
+in des_fcrypt.patch.
+
+Perl will also build without des_fcrypt(), but the crypt() builtin will
+fail at run time.
+
+Be sure to read the instructions near the top of the makefiles carefully.
+
+=item *
+
+Type "dmake" (or "nmake" if you are using that make).
+
+This should build everything.  Specifically, it will create perl.exe,
+perl56.dll at the perl toplevel, and various other extension dll's
+under the lib\auto directory.  If the build fails for any reason, make
+sure you have done the previous steps correctly.
+
+=back
+
+=head2 Testing
+
+Type "dmake test" (or "nmake test").  This will run most of the tests from
+the testsuite (many tests will be skipped).
+
+There should be no test failures when running under Windows NT 4.0 or
+Windows 2000.  Many tests I<will> fail under Windows 9x due to the inferior
+command shell.
+
+Some test failures may occur if you use a command shell other than the
+native "cmd.exe", or if you are building from a path that contains
+spaces.  So don't do that.
+
+If you are running the tests from a emacs shell window, you may see
+failures in op/stat.t.  Run "dmake test-notty" in that case.
+
+If you're using the Borland compiler, you may see a failure in op/taint.t
+arising from the inability to find the Borland Runtime DLLs on the system
+default path.  You will need to copy the DLLs reported by the messages
+from where Borland chose to install it, into the Windows system directory
+(usually somewhere like C:\WINNT\SYSTEM32), and rerun the test.
+
+Please report any other failures as described under L<BUGS AND CAVEATS>.
+
+=head2 Installation
+
+Type "dmake install" (or "nmake install").  This will put the newly
+built perl and the libraries under whatever C<INST_TOP> points to in the
+Makefile.  It will also install the pod documentation under
+C<$INST_TOP\$VERSION\lib\pod> and HTML versions of the same under
+C<$INST_TOP\$VERSION\lib\pod\html>.  To use the Perl you just installed,
+you will need to add two components to your PATH environment variable,
+C<$INST_TOP\$VERSION\bin>, and C<$INST_TOP\$VERSION\bin\$ARCHNAME>.
+For example:
+
+    set PATH c:\perl\5.6.0\bin;c:\perl\5.6.0\bin\MSWin32-x86;%PATH%
+
+If you opt to comment out INST_VER and INST_ARCH in the makefiles, the
+installation structure is much simpler.  In that case, it will be
+sufficient to add a single entry to the path, for instance:
+
+    set PATH c:\perl\bin;%PATH%
+
+=head2 Usage Hints
+
+=over 4
+
+=item Environment Variables
+
+The installation paths that you set during the build get compiled
+into perl, so you don't have to do anything additional to start
+using that perl (except add its location to your PATH variable).
+
+If you put extensions in unusual places, you can set PERL5LIB
+to a list of paths separated by semicolons where you want perl
+to look for libraries.  Look for descriptions of other environment
+variables you can set in L<perlrun>.
+
+You can also control the shell that perl uses to run system() and
+backtick commands via PERL5SHELL.  See L<perlrun>.
+
+Perl does not depend on the registry, but it can look up certain default
+values if you choose to put them there.  Perl attempts to read entries from
+C<HKEY_CURRENT_USER\Software\Perl> and C<HKEY_LOCAL_MACHINE\Software\Perl>.
+Entries in the former override entries in the latter.  One or more of the
+following entries (of type REG_SZ or REG_EXPAND_SZ) may be set:
+
+    lib-$]		version-specific standard library path to add to @INC
+    lib			standard library path to add to @INC
+    sitelib-$]		version-specific site library path to add to @INC
+    sitelib		site library path to add to @INC
+    vendorlib-$]	version-specific vendor library path to add to @INC
+    vendorlib		vendor library path to add to @INC
+    PERL*		fallback for all %ENV lookups that begin with "PERL"
+
+Note the C<$]> in the above is not literal.  Substitute whatever version
+of perl you want to honor that entry, e.g. C<5.6.0>.  Paths must be
+separated with semicolons, as usual on win32.
+
+=item File Globbing
+
+By default, perl handles file globbing using the File::Glob extension,
+which provides portable globbing.
+
+If you want perl to use globbing that emulates the quirks of DOS
+filename conventions, you might want to consider using File::DosGlob
+to override the internal glob() implementation.  See L<File::DosGlob> for
+details.
+
+=item Using perl from the command line
+
+If you are accustomed to using perl from various command-line
+shells found in UNIX environments, you will be less than pleased
+with what Windows offers by way of a command shell.
+
+The crucial thing to understand about the Windows environment is that
+the command line you type in is processed twice before Perl sees it.
+First, your command shell (usually CMD.EXE on Windows NT, and
+COMMAND.COM on Windows 9x) preprocesses the command line, to handle
+redirection, environment variable expansion, and location of the
+executable to run. Then, the perl executable splits the remaining
+command line into individual arguments, using the C runtime library
+upon which Perl was built.
+
+It is particularly important to note that neither the shell nor the C
+runtime do any wildcard expansions of command-line arguments (so
+wildcards need not be quoted).  Also, the quoting behaviours of the
+shell and the C runtime are rudimentary at best (and may, if you are
+using a non-standard shell, be inconsistent).  The only (useful) quote
+character is the double quote (").  It can be used to protect spaces in
+arguments and other special characters.  The Windows NT documentation
+has almost no description of how the quoting rules are implemented, but
+here are some general observations based on experiments:  The C runtime
+breaks arguments at spaces and passes them to programs in argc/argv.
+Doublequotes can be used to prevent arguments with spaces in them from
+being split up.  You can put a double quote in an argument by escaping
+it with a backslash and enclosing the whole argument within double
+quotes.  The backslash and the pair of double quotes surrounding the
+argument will be stripped by the C runtime.
+
+The file redirection characters "<", ">", and "|" can be quoted by
+double quotes (although there are suggestions that this may not always
+be true).  Single quotes are not treated as quotes by the shell or the C
+runtime.  The caret "^" has also been observed to behave as a quoting
+character, but this appears to be a shell feature, and the caret is not
+stripped from the command line, so Perl still sees it (and the C runtime
+phase does not treat the caret as a quote character).
+
+Here are some examples of usage of the "cmd" shell:
+
+This prints two doublequotes:
+
+    perl -e "print '\"\"' "
+
+This does the same:
+
+    perl -e "print \"\\\"\\\"\" "
+
+This prints "bar" and writes "foo" to the file "blurch":
+
+    perl -e "print 'foo'; print STDERR 'bar'" > blurch
+
+This prints "foo" ("bar" disappears into nowhereland):
+
+    perl -e "print 'foo'; print STDERR 'bar'" 2> nul
+
+This prints "bar" and writes "foo" into the file "blurch":
+
+    perl -e "print 'foo'; print STDERR 'bar'" 1> blurch
+
+This pipes "foo" to the "less" pager and prints "bar" on the console:
+
+    perl -e "print 'foo'; print STDERR 'bar'" | less
+
+This pipes "foo\nbar\n" to the less pager:
+
+    perl -le "print 'foo'; print STDERR 'bar'" 2>&1 | less
+
+This pipes "foo" to the pager and writes "bar" in the file "blurch":
+
+    perl -e "print 'foo'; print STDERR 'bar'" 2> blurch | less
+
+
+Discovering the usefulness of the "command.com" shell on Windows 9x
+is left as an exercise to the reader :)
+
+One particularly pernicious problem with the 4NT command shell for
+Windows NT is that it (nearly) always treats a % character as indicating
+that environment variable expansion is needed.  Under this shell, it is
+therefore important to always double any % characters which you want
+Perl to see (for example, for hash variables), even when they are
+quoted.
+
+=item Building Extensions
+
+The Comprehensive Perl Archive Network (CPAN) offers a wealth
+of extensions, some of which require a C compiler to build.
+Look in http://www.cpan.org/ for more information on CPAN.
+
+Note that not all of the extensions available from CPAN may work
+in the Win32 environment; you should check the information at
+http://testers.cpan.org/ before investing too much effort into
+porting modules that don't readily build.
+
+Most extensions (whether they require a C compiler or not) can
+be built, tested and installed with the standard mantra:
+
+    perl Makefile.PL
+    $MAKE
+    $MAKE test
+    $MAKE install
+
+where $MAKE is whatever 'make' program you have configured perl to
+use.  Use "perl -V:make" to find out what this is.  Some extensions
+may not provide a testsuite (so "$MAKE test" may not do anything, or
+fail), but most serious ones do.
+
+It is important that you use a supported 'make' program, and
+ensure Config.pm knows about it.  If you don't have nmake, you can
+either get dmake from the location mentioned earlier, or get an
+old version of nmake reportedly available from:
+
+    ftp://ftp.microsoft.com/Softlib/MSLFILES/nmake15.exe
+
+Another option is to use the make written in Perl, available from
+CPAN:
+
+    http://www.cpan.org/authors/id/NI-S/Make-0.03.tar.gz
+
+You may also use dmake.  See L</"Make"> above on how to get it.
+
+Note that MakeMaker actually emits makefiles with different syntax
+depending on what 'make' it thinks you are using.  Therefore, it is
+important that one of the following values appears in Config.pm:
+
+    make='nmake'	# MakeMaker emits nmake syntax
+    make='dmake'	# MakeMaker emits dmake syntax
+    any other value	# MakeMaker emits generic make syntax
+    			    (e.g GNU make, or Perl make)
+
+If the value doesn't match the 'make' program you want to use,
+edit Config.pm to fix it.
+
+If a module implements XSUBs, you will need one of the supported
+C compilers.  You must make sure you have set up the environment for
+the compiler for command-line compilation.
+
+If a module does not build for some reason, look carefully for
+why it failed, and report problems to the module author.  If
+it looks like the extension building support is at fault, report
+that with full details of how the build failed using the perlbug
+utility.
+
+=item Command-line Wildcard Expansion
+
+The default command shells on DOS descendant operating systems (such
+as they are) usually do not expand wildcard arguments supplied to
+programs.  They consider it the application's job to handle that.
+This is commonly achieved by linking the application (in our case,
+perl) with startup code that the C runtime libraries usually provide.
+However, doing that results in incompatible perl versions (since the
+behavior of the argv expansion code differs depending on the
+compiler, and it is even buggy on some compilers).  Besides, it may
+be a source of frustration if you use such a perl binary with an
+alternate shell that *does* expand wildcards.
+
+Instead, the following solution works rather well. The nice things
+about it: 1) you can start using it right away 2) it is more powerful,
+because it will do the right thing with a pattern like */*/*.c
+3) you can decide whether you do/don't want to use it 4) you can
+extend the method to add any customizations (or even entirely
+different kinds of wildcard expansion).
+
+	C:\> copy con c:\perl\lib\Wild.pm
+	# Wild.pm - emulate shell @ARGV expansion on shells that don't
+	use File::DosGlob;
+	@ARGV = map {
+		      my @g = File::DosGlob::glob($_) if /[*?]/;
+		      @g ? @g : $_;
+		    } @ARGV;
+	1;
+	^Z
+	C:\> set PERL5OPT=-MWild
+	C:\> perl -le "for (@ARGV) { print }" */*/perl*.c
+	p4view/perl/perl.c
+	p4view/perl/perlio.c
+	p4view/perl/perly.c
+	perl5.005/win32/perlglob.c
+	perl5.005/win32/perllib.c
+	perl5.005/win32/perlglob.c
+	perl5.005/win32/perllib.c
+	perl5.005/win32/perlglob.c
+	perl5.005/win32/perllib.c
+
+Note there are two distinct steps there: 1) You'll have to create
+Wild.pm and put it in your perl lib directory. 2) You'll need to
+set the PERL5OPT environment variable.  If you want argv expansion
+to be the default, just set PERL5OPT in your default startup
+environment.
+
+If you are using the Visual C compiler, you can get the C runtime's
+command line wildcard expansion built into perl binary.  The resulting
+binary will always expand unquoted command lines, which may not be
+what you want if you use a shell that does that for you.  The expansion
+done is also somewhat less powerful than the approach suggested above.
+
+=item Win32 Specific Extensions
+
+A number of extensions specific to the Win32 platform are available
+from CPAN.  You may find that many of these extensions are meant to
+be used under the Activeware port of Perl, which used to be the only
+native port for the Win32 platform.  Since the Activeware port does not
+have adequate support for Perl's extension building tools, these
+extensions typically do not support those tools either, and therefore
+cannot be built using the generic steps shown in the previous section.
+
+To ensure smooth transitioning of existing code that uses the
+ActiveState port, there is a bundle of Win32 extensions that contains
+all of the ActiveState extensions and most other Win32 extensions from
+CPAN in source form, along with many added bugfixes, and with MakeMaker
+support.  This bundle is available at:
+
+   http://www.cpan.org/authors/id/GSAR/libwin32-0.151.zip
+
+See the README in that distribution for building and installation
+instructions.  Look for later versions that may be available at the
+same location.
+
+=item Running Perl Scripts
+
+Perl scripts on UNIX use the "#!" (a.k.a "shebang") line to
+indicate to the OS that it should execute the file using perl.
+Win32 has no comparable means to indicate arbitrary files are
+executables.
+
+Instead, all available methods to execute plain text files on
+Win32 rely on the file "extension".  There are three methods
+to use this to execute perl scripts:
+
+=over 8
+
+=item 1
+
+There is a facility called "file extension associations" that will
+work in Windows NT 4.0.  This can be manipulated via the two
+commands "assoc" and "ftype" that come standard with Windows NT
+4.0.  Type "ftype /?" for a complete example of how to set this
+up for perl scripts (Say what?  You thought Windows NT wasn't
+perl-ready? :).
+
+=item 2
+
+Since file associations don't work everywhere, and there are
+reportedly bugs with file associations where it does work, the
+old method of wrapping the perl script to make it look like a
+regular batch file to the OS, may be used.  The install process
+makes available the "pl2bat.bat" script which can be used to wrap
+perl scripts into batch files.  For example:
+
+	pl2bat foo.pl
+
+will create the file "FOO.BAT".  Note "pl2bat" strips any
+.pl suffix and adds a .bat suffix to the generated file.
+
+If you use the 4DOS/NT or similar command shell, note that
+"pl2bat" uses the "%*" variable in the generated batch file to
+refer to all the command line arguments, so you may need to make
+sure that construct works in batch files.  As of this writing,
+4DOS/NT users will need a "ParameterChar = *" statement in their
+4NT.INI file, or will need to execute "setdos /p*" in the 4DOS/NT
+startup file to enable this to work.
+
+=item 3
+
+Using "pl2bat" has a few problems:  the file name gets changed,
+so scripts that rely on C<$0> to find what they must do may not
+run properly; running "pl2bat" replicates the contents of the
+original script, and so this process can be maintenance intensive
+if the originals get updated often.  A different approach that
+avoids both problems is possible.
+
+A script called "runperl.bat" is available that can be copied
+to any filename (along with the .bat suffix).  For example,
+if you call it "foo.bat", it will run the file "foo" when it is
+executed.  Since you can run batch files on Win32 platforms simply
+by typing the name (without the extension), this effectively
+runs the file "foo", when you type either "foo" or "foo.bat".
+With this method, "foo.bat" can even be in a different location
+than the file "foo", as long as "foo" is available somewhere on
+the PATH.  If your scripts are on a filesystem that allows symbolic
+links, you can even avoid copying "runperl.bat".
+
+Here's a diversion:  copy "runperl.bat" to "runperl", and type
+"runperl".  Explain the observed behavior, or lack thereof. :)
+Hint: .gnidnats llits er'uoy fi ,"lrepnur" eteled :tniH
+
+=back
+
+=item Miscellaneous Things
+
+A full set of HTML documentation is installed, so you should be
+able to use it if you have a web browser installed on your
+system.
+
+C<perldoc> is also a useful tool for browsing information contained
+in the documentation, especially in conjunction with a pager
+like C<less> (recent versions of which have Win32 support).  You may
+have to set the PAGER environment variable to use a specific pager.
+"perldoc -f foo" will print information about the perl operator
+"foo".
+
+If you find bugs in perl, you can run C<perlbug> to create a
+bug report (you may have to send it manually if C<perlbug> cannot
+find a mailer on your system).
+
+=back
+
+=head1 BUGS AND CAVEATS
+
+Some of the built-in functions do not act exactly as documented in
+L<perlfunc>, and a few are not implemented at all.  To avoid
+surprises, particularly if you have had prior exposure to Perl
+in other operating environments or if you intend to write code
+that will be portable to other environments, see L<perlport>
+for a reasonably definitive list of these differences.
+
+Not all extensions available from CPAN may build or work properly
+in the Win32 environment.  See L</"Building Extensions">.
+
+Most C<socket()> related calls are supported, but they may not
+behave as on Unix platforms.  See L<perlport> for the full list.
+
+Signal handling may not behave as on Unix platforms (where it
+doesn't exactly "behave", either :).  For instance, calling C<die()>
+or C<exit()> from signal handlers will cause an exception, since most
+implementations of C<signal()> on Win32 are severely crippled.
+Thus, signals may work only for simple things like setting a flag
+variable in the handler.  Using signals under this port should
+currently be considered unsupported.
+
+Please send detailed descriptions of any problems and solutions that 
+you may find to <F<perlbug@perl.com>>, along with the output produced
+by C<perl -V>.
+
+=head1 AUTHORS
+
+=over 4
+
+Gary Ng E<lt>71564.1743@CompuServe.COME<gt>
+
+Gurusamy Sarathy E<lt>gsar@activestate.comE<gt>
+
+Nick Ing-Simmons E<lt>nick@ni-s.u-net.comE<gt>
+
+=back
+
+This document is maintained by Gurusamy Sarathy.
+
+=head1 SEE ALSO
+
+L<perl>
+
+=head1 HISTORY
+
+This port was originally contributed by Gary Ng around 5.003_24,
+and borrowed from the Hip Communications port that was available
+at the time.  Various people have made numerous and sundry hacks
+since then.
+
+Borland support was added in 5.004_01 (Gurusamy Sarathy).
+
+GCC/mingw32 support was added in 5.005 (Nick Ing-Simmons).
+
+Support for PERL_OBJECT was added in 5.005 (ActiveState Tool Corp).
+
+Support for fork() emulation was added in 5.6 (ActiveState Tool Corp).
+
+Win9x support was added in 5.6 (Benjamin Stuhl).
+
+Last updated: 22 March 2000
+
+=cut
diff --git a/djgpp/configure.bat b/djgpp/configure.bat
index 64b46ec34f..e7d41d7130 100644
--- a/djgpp/configure.bat
+++ b/djgpp/configure.bat
@@ -1,37 +1,37 @@
-@echo off

-set CONFIG=

-set PATH_SEPARATOR=;

-set PATH_EXPAND=y

-sh -c 'if test $PATH_SEPARATOR = ";"; then exit 1; fi'

-if ERRORLEVEL 1 goto path_sep_ok

-echo Error:

-echo Make sure the environment variable PATH_SEPARATOR=; while building perl!

-echo Please check your DJGPP.ENV!

-goto end

-

-:path_sep_ok

-sh -c 'if test $PATH_EXPAND = "Y" -o $PATH_EXPAND = "y"; then exit 1; fi'

-if ERRORLEVEL 1 goto path_exp_ok

-echo Error:

-echo Make sure the environment variable PATH_EXPAND=Y while building perl!

-echo Please check your DJGPP.ENV!

-goto end

-

-:path_exp_ok

-sh -c '$SHELL -c "exit 128"'

-if ERRORLEVEL 128 goto shell_ok

-

-echo Error:

-echo The SHELL environment variable must be set to the full path of your sh.exe!

-goto end

-

-:shell_ok

-sh -c 'if test ! -d /tmp; then mkdir /tmp; fi'

-cp djgpp.c config.over ..

-cd ..

-echo Running sed...

-sh djgpp/djgppsed.sh

-

-echo Running Configure...

-sh Configure %1 %2 %3 %4 %5 %6 %7 %8 %9

-:end

+@echo off
+set CONFIG=
+set PATH_SEPARATOR=;
+set PATH_EXPAND=y
+sh -c 'if test $PATH_SEPARATOR = ";"; then exit 1; fi'
+if ERRORLEVEL 1 goto path_sep_ok
+echo Error:
+echo Make sure the environment variable PATH_SEPARATOR=; while building perl!
+echo Please check your DJGPP.ENV!
+goto end
+
+:path_sep_ok
+sh -c 'if test $PATH_EXPAND = "Y" -o $PATH_EXPAND = "y"; then exit 1; fi'
+if ERRORLEVEL 1 goto path_exp_ok
+echo Error:
+echo Make sure the environment variable PATH_EXPAND=Y while building perl!
+echo Please check your DJGPP.ENV!
+goto end
+
+:path_exp_ok
+sh -c '$SHELL -c "exit 128"'
+if ERRORLEVEL 128 goto shell_ok
+
+echo Error:
+echo The SHELL environment variable must be set to the full path of your sh.exe!
+goto end
+
+:shell_ok
+sh -c 'if test ! -d /tmp; then mkdir /tmp; fi'
+cp djgpp.c config.over ..
+cd ..
+echo Running sed...
+sh djgpp/djgppsed.sh
+
+echo Running Configure...
+sh Configure %1 %2 %3 %4 %5 %6 %7 %8 %9
+:end
diff --git a/win32/Makefile b/win32/Makefile
index 094f93c212..af119909e8 100644
--- a/win32/Makefile
+++ b/win32/Makefile
@@ -1,1120 +1,1120 @@
-#

-# Makefile to build perl on Windows NT using Microsoft NMAKE.

-#

-# This is set up to build a perl.exe that runs off a shared library

-# (perl56.dll).  Also makes individual DLLs for the XS extensions.

-#

-

-##

-## Make sure you read README.win32 *before* you mess with anything here!

-##

-

-##

-## Build configuration.  Edit the values below to suit your needs.

-##

-

-#

-# Set these to wherever you want "nmake install" to put your

-# newly built perl.

-#

-INST_DRV	= c:

-INST_TOP	= $(INST_DRV)\perl

-

-#

-# Comment this out if you DON'T want your perl installation to be versioned.

-# This means that the new installation will overwrite any files from the

-# old installation at the same INST_TOP location.  Leaving it enabled is

-# the safest route, as perl adds the extra version directory to all the

-# locations it installs files to.  If you disable it, an alternative

-# versioned installation can be obtained by setting INST_TOP above to a

-# path that includes an arbitrary version string.

-#

-INST_VER	= \5.6.0

-

-#

-# Comment this out if you DON'T want your perl installation to have

-# architecture specific components.  This means that architecture-

-# specific files will be installed along with the architecture-neutral

-# files.  Leaving it enabled is safer and more flexible, in case you

-# want to build multiple flavors of perl and install them together in

-# the same location.  Commenting it out gives you a simpler

-# installation that is easier to understand for beginners.

-#

-INST_ARCH	= \$(ARCHNAME)

-

-#

-# uncomment to enable multiple interpreters.  This is need for fork()

-# emulation.

-#

-#USE_MULTI	= define

-

-#

-# Beginnings of interpreter cloning/threads; still very incomplete.

-# This should be enabled to get the fork() emulation.  This needs

-# USE_MULTI as well.

-#

-#USE_ITHREADS	= define

-

-#

-# uncomment to enable the implicit "host" layer for all system calls

-# made by perl.  This needs USE_MULTI above.  This is also needed to

-# get fork().

-#

-#USE_IMP_SYS	= define

-

-#

-# WARNING! This option is deprecated and will eventually go away (enable

-# USE_ITHREADS instead).

-#

-# uncomment to enable threads-capabilities.  This is incompatible with

-# USE_ITHREADS, and is only here for people who may have come to rely

-# on the experimental Thread support that was in 5.005.

-#

-#USE_5005THREADS= define

-

-#

-# WARNING! This option is deprecated and will eventually go away (enable

-# USE_MULTI instead).

-#

-# uncomment next line if you want to use the PERL_OBJECT build option.

-# DO NOT ENABLE unless you have legacy code that relies on the C++

-# CPerlObj class that was available in 5.005.  This cannot be enabled

-# if you ask for USE_5005THREADS above.

-#

-#USE_OBJECT	= define

-

-#

-# uncomment one of the following lines if you are using either

-# Visual C++ 2.x or Visual C++ 6.x (aka Visual Studio 98)

-#

-#CCTYPE		= MSVC20

-#CCTYPE		= MSVC60

-

-#

-# uncomment next line if you want debug version of perl (big,slow)

-#

-#CFG		= Debug

-

-#

-# uncomment to enable use of PerlCRT.DLL when using the Visual C compiler.

-# It has patches that fix known bugs in older versions of MSVCRT.DLL.

-# This currently requires VC 5.0 with Service Pack 3 or later.

-# Get it from CPAN at http://www.perl.com/CPAN/authors/id/D/DO/DOUGL/

-# and follow the directions in the package to install.

-#

-# Not recommended if you have VC 6.x and you're not running Windows 9x.

-#

-#USE_PERLCRT	= define

-

-#

-# uncomment to enable linking with setargv.obj under the Visual C

-# compiler. Setting this options enables perl to expand wildcards in

-# arguments, but it may be harder to use alternate methods like

-# File::DosGlob that are more powerful.  This option is supported only with

-# Visual C.

-#

-#USE_SETARGV	= define

-

-#

-# if you have the source for des_fcrypt(), uncomment this and make sure the

-# file exists (see README.win32).  File should be located in the same

-# directory as this file.

-#

-#CRYPT_SRC	= fcrypt.c

-

-#

-# if you didn't set CRYPT_SRC and if you have des_fcrypt() available in a

-# library, uncomment this, and make sure the library exists (see README.win32)

-# Specify the full pathname of the library.

-#

-#CRYPT_LIB	= fcrypt.lib

-

-#

-# set this if you wish to use perl's malloc

-# WARNING: Turning this on/off WILL break binary compatibility with extensions

-# you may have compiled with/without it.  Be prepared to recompile all

-# extensions if you change the default.  Currently, this cannot be enabled

-# if you ask for USE_IMP_SYS above.

-#

-#PERL_MALLOC	= define

-

-#

-# set the install locations of the compiler include/libraries

-# Running VCVARS32.BAT is *required* when using Visual C.

-# Some versions of Visual C don't define MSVCDIR in the environment,

-# so you may have to set CCHOME explicitly (spaces in the path name should

-# not be quoted)

-#

-#CCHOME		= f:\msvc20

-CCHOME		= $(MSVCDIR)

-CCINCDIR	= $(CCHOME)\include

-CCLIBDIR	= $(CCHOME)\lib

-

-#

-# Additional compiler flags can be specified here.

-#

-

-#

-# This should normally be disabled.  Adding -DPERL_POLLUTE enables support

-# for old symbols by default, at the expense of extreme pollution.  You most

-# probably just want to build modules that won't compile with

-#         perl Makefile.PL POLLUTE=1

-# instead of enabling this.  Please report such modules to the respective

-# authors.

-#

-#BUILDOPT	= $(BUILDOPT) -DPERL_POLLUTE

-

-#

-# This should normally be disabled.  Enabling it will disable the File::Glob

-# implementation of CORE::glob.

-#

-#BUILDOPT	= $(BUILDOPT) -DPERL_EXTERNAL_GLOB

-

-#

-# This should normally be disabled.  Enabling it causes perl to read scripts

-# in text mode (which is the 5.005 behavior) and will break ByteLoader.

-#BUILDOPT	= $(BUILDOPT) -DPERL_TEXTMODE_SCRIPTS

-

-#

-# specify semicolon-separated list of extra directories that modules will

-# look for libraries (spaces in path names need not be quoted)

-#

-EXTRALIBDIRS	=

-

-#

-# set this to your email address (perl will guess a value from

-# from your loginname and your hostname, which may not be right)

-#

-#EMAIL		=

-

-##

-## Build configuration ends.

-##

-

-##################### CHANGE THESE ONLY IF YOU MUST #####################

-

-!IF "$(CRYPT_SRC)$(CRYPT_LIB)" == ""

-D_CRYPT		= undef

-!ELSE

-D_CRYPT		= define

-CRYPT_FLAG	= -DHAVE_DES_FCRYPT

-!ENDIF

-

-!IF "$(USE_OBJECT)" == "define"

-PERL_MALLOC	= undef

-USE_5005THREADS	= undef

-USE_MULTI	= undef

-USE_IMP_SYS	= define

-!ENDIF

-

-!IF "$(PERL_MALLOC)" == ""

-PERL_MALLOC	= undef

-!ENDIF

-

-!IF "$(USE_5005THREADS)" == ""

-USE_5005THREADS	= undef

-!ENDIF

-

-!IF "$(USE_5005THREADS)" == "define"

-USE_ITHREADS	= undef

-!ENDIF

-

-!IF "$(USE_IMP_SYS)" == "define"

-PERL_MALLOC	= undef

-!ENDIF

-

-!IF "$(USE_MULTI)" == ""

-USE_MULTI	= undef

-!ENDIF

-

-!IF "$(USE_OBJECT)" == ""

-USE_OBJECT	= undef

-!ENDIF

-

-!IF "$(USE_ITHREADS)" == ""

-USE_ITHREADS	= undef

-!ENDIF

-

-!IF "$(USE_IMP_SYS)" == ""

-USE_IMP_SYS	= undef

-!ENDIF

-

-!IF "$(USE_PERLCRT)" == ""

-USE_PERLCRT	= undef

-!ENDIF

-

-!IF "$(USE_IMP_SYS)$(USE_MULTI)$(USE_5005THREADS)$(USE_OBJECT)" == "defineundefundefundef"

-USE_MULTI	= define

-!ENDIF

-

-!IF "$(USE_ITHREADS)$(USE_MULTI)$(USE_OBJECT)" == "defineundefundef"

-USE_MULTI	= define

-USE_5005THREADS	= undef

-!ENDIF

-

-!IF "$(USE_MULTI)$(USE_5005THREADS)$(USE_OBJECT)" != "undefundefundef"

-BUILDOPT	= $(BUILDOPT) -DPERL_IMPLICIT_CONTEXT

-!ENDIF

-

-!IF "$(USE_IMP_SYS)" != "undef"

-BUILDOPT	= $(BUILDOPT) -DPERL_IMPLICIT_SYS

-!ENDIF

-

-!IF "$(PROCESSOR_ARCHITECTURE)" == ""

-PROCESSOR_ARCHITECTURE	= x86

-!ENDIF

-

-!IF "$(USE_OBJECT)" == "define"

-ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-object

-!ELSE

-!IF "$(USE_5005THREADS)" == "define"

-ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-thread

-!ELSE

-!IF "$(USE_MULTI)" == "define"

-ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-multi

-!ELSE

-ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)

-!ENDIF

-!ENDIF

-!ENDIF

-

-!IF "$(USE_ITHREADS)" == "define"

-ARCHNAME	= $(ARCHNAME)-thread

-!ENDIF

-

-# Visual Studio 98 specific

-!IF "$(CCTYPE)" == "MSVC60"

-

-# VC 6.0 can load the socket dll on demand.  Makes the test suite

-# run in about 10% less time.

-DELAYLOAD	= -DELAYLOAD:wsock32.dll -DELAYLOAD:shell32.dll delayimp.lib 

-

-# VC 6.0 seems capable of compiling perl correctly with optimizations

-# enabled.  Anything earlier fails tests.

-!IF "$(CFG)" == ""

-CFG		= Optimize

-!ENDIF

-!ENDIF

-

-ARCHDIR		= ..\lib\$(ARCHNAME)

-COREDIR		= ..\lib\CORE

-AUTODIR		= ..\lib\auto

-LIBDIR		= ..\lib

-EXTDIR		= ..\ext

-PODDIR		= ..\pod

-EXTUTILSDIR	= $(LIBDIR)\ExtUtils

-

-#

-INST_SCRIPT	= $(INST_TOP)$(INST_VER)\bin

-INST_BIN	= $(INST_SCRIPT)$(INST_ARCH)

-INST_LIB	= $(INST_TOP)$(INST_VER)\lib

-INST_ARCHLIB	= $(INST_LIB)$(INST_ARCH)

-INST_COREDIR	= $(INST_ARCHLIB)\CORE

-INST_POD	= $(INST_LIB)\pod

-INST_HTML	= $(INST_POD)\html

-

-#

-# Programs to compile, build .lib files and link

-#

-

-CC		= cl

-LINK32		= link

-LIB32		= $(LINK32) -lib

-RSC		= rc

-

-#

-# Options

-#

-

-INCLUDES	= -I$(COREDIR) -I.\include -I. -I..

-#PCHFLAGS	= -Fpc:\temp\vcmoduls.pch -YX 

-DEFINES		= -DWIN32 -D_CONSOLE -DNO_STRICT $(CRYPT_FLAG)

-LOCDEFS		= -DPERLDLL -DPERL_CORE

-SUBSYS		= console

-CXX_FLAG	= -TP -GX

-

-!IF "$(USE_PERLCRT)" != "define"

-LIBC	= msvcrt.lib

-!ELSE

-LIBC	= PerlCRT.lib

-!ENDIF

-

-PERLEXE_RES	=

-PERLDLL_RES	=

-

-!IF  "$(CFG)" == "Debug"

-!  IF "$(CCTYPE)" == "MSVC20"

-OPTIMIZE	= -Od -MD -Z7 -DDEBUGGING

-!  ELSE

-OPTIMIZE	= -Od -MD -Zi -DDEBUGGING

-!  ENDIF

-LINK_DBG	= -debug -pdb:none

-!ELSE

-!  IF  "$(CFG)" == "Optimize"

-# -O1 yields smaller code, which turns out to be faster than -O2

-#OPTIMIZE	= -O2 -MD -DNDEBUG

-OPTIMIZE	= -O1 -MD -DNDEBUG

-!  ELSE

-OPTIMIZE	= -Od -MD -DNDEBUG

-!  ENDIF

-LINK_DBG	= -release

-!ENDIF

-

-!IF "$(USE_OBJECT)" == "define"

-OPTIMIZE	= $(OPTIMIZE) $(CXX_FLAG)

-BUILDOPT	= $(BUILDOPT) -DPERL_OBJECT

-!ENDIF

-

-!IF "$(USE_PERLCRT)" != "define"

-BUILDOPT	= $(BUILDOPT) -DPERL_MSVCRT_READFIX

-!ENDIF

-

-LIBBASEFILES	= $(CRYPT_LIB) \

-		oldnames.lib kernel32.lib user32.lib gdi32.lib winspool.lib \

-		comdlg32.lib advapi32.lib shell32.lib ole32.lib oleaut32.lib \

-		netapi32.lib uuid.lib wsock32.lib mpr.lib winmm.lib \

-		version.lib odbc32.lib odbccp32.lib

-

-# we add LIBC here, since we may be using PerlCRT.dll

-LIBFILES	= $(LIBBASEFILES) $(LIBC)

-

-CFLAGS		= -nologo -Gf -W3 $(INCLUDES) $(DEFINES) $(LOCDEFS) \

-		$(PCHFLAGS) $(OPTIMIZE)

-LINK_FLAGS	= -nologo -nodefaultlib $(LINK_DBG) \

-		-libpath:"$(INST_COREDIR)" \

-		-machine:$(PROCESSOR_ARCHITECTURE)

-OBJOUT_FLAG	= -Fo

-EXEOUT_FLAG	= -Fe

-

-CFLAGS_O	= $(CFLAGS) $(BUILDOPT)

-

-#################### do not edit below this line #######################

-############# NO USER-SERVICEABLE PARTS BEYOND THIS POINT ##############

-

-o = .obj

-

-#

-# Rules

-# 

-

-.SUFFIXES : .c $(o) .dll .lib .exe .rc .res

-

-.c$(o):

-	$(CC) -c -I$(<D) $(CFLAGS_O) $(OBJOUT_FLAG)$@ $<

-

-.y.c:

-	$(NOOP)

-

-$(o).dll:

-	$(LINK32) -dll -subsystem:windows -implib:$(*B).lib -def:$(*B).def \

-	    -out:$@ $(LINK_FLAGS) $(LIBFILES) $< $(LIBPERL)  

-

-.rc.res:

-	$(RSC) -i.. $<

-

-#

-# various targets

-PERLIMPLIB	= ..\perl56.lib

-PERLDLL		= ..\perl56.dll

-

-MINIPERL	= ..\miniperl.exe

-MINIDIR		= .\mini

-PERLEXE		= ..\perl.exe

-WPERLEXE	= ..\wperl.exe

-GLOBEXE		= ..\perlglob.exe

-CONFIGPM	= ..\lib\Config.pm

-MINIMOD		= ..\lib\ExtUtils\Miniperl.pm

-X2P		= ..\x2p\a2p.exe

-

-PL2BAT		= bin\pl2bat.pl

-GLOBBAT		= bin\perlglob.bat

-

-UTILS		=			\

-		..\utils\h2ph		\

-		..\utils\splain		\

-		..\utils\dprofpp	\

-		..\utils\perlbug	\

-		..\utils\pl2pm 		\

-		..\utils\c2ph		\

-		..\utils\h2xs		\

-		..\utils\perldoc	\

-		..\utils\perlcc		\

-		..\pod\checkpods	\

-		..\pod\pod2html		\

-		..\pod\pod2latex	\

-		..\pod\pod2man		\

-		..\pod\pod2text		\

-		..\pod\pod2usage	\

-		..\pod\podchecker	\

-		..\pod\podselect	\

-		..\x2p\find2perl	\

-		..\x2p\s2p		\

-		bin\exetype.pl		\

-		bin\runperl.pl		\

-		bin\pl2bat.pl		\

-		bin\perlglob.pl		\

-		bin\search.pl

-

-MAKE		= nmake -nologo

-

-CFGSH_TMPL	= config.vc

-CFGH_TMPL	= config_H.vc

-

-XCOPY		= xcopy /f /r /i /d

-RCOPY		= xcopy /f /r /i /e /d

-NOOP		= @echo

-NULL		=

-

-#

-# filenames given to xsubpp must have forward slashes (since it puts

-# full pathnames in #line strings)

-XSUBPP		= ..\$(MINIPERL) -I..\..\lib ..\$(EXTUTILSDIR)\xsubpp \

-		-C++ -prototypes

-

-MICROCORE_SRC	=		\

-		..\av.c		\

-		..\deb.c	\

-		..\doio.c	\

-		..\doop.c	\

-		..\dump.c	\

-		..\globals.c	\

-		..\gv.c		\

-		..\hv.c		\

-		..\mg.c		\

-		..\op.c		\

-		..\perl.c	\

-		..\perlapi.c	\

-		..\perly.c	\

-		..\pp.c		\

-		..\pp_ctl.c	\

-		..\pp_hot.c	\

-		..\pp_sys.c	\

-		..\regcomp.c	\

-		..\regexec.c	\

-		..\run.c	\

-		..\scope.c	\

-		..\sv.c		\

-		..\taint.c	\

-		..\toke.c	\

-		..\universal.c	\

-		..\utf8.c	\

-		..\util.c	\

-		..\xsutils.c

-

-EXTRACORE_SRC	= $(EXTRACORE_SRC) perllib.c

-

-!IF "$(PERL_MALLOC)" == "define"

-EXTRACORE_SRC	= $(EXTRACORE_SRC) ..\malloc.c

-!ENDIF

-

-!IF "$(USE_OBJECT)" != "define"

-EXTRACORE_SRC	= $(EXTRACORE_SRC) ..\perlio.c

-!ENDIF

-

-WIN32_SRC	=		\

-		.\win32.c	\

-		.\win32sck.c	\

-		.\win32thread.c 

-

-!IF "$(CRYPT_SRC)" != ""

-WIN32_SRC	= $(WIN32_SRC) .\$(CRYPT_SRC)

-!ENDIF

-

-DLL_SRC		= $(DYNALOADER).c

-

-X2P_SRC		=		\

-		..\x2p\a2p.c	\

-		..\x2p\hash.c	\

-		..\x2p\str.c	\

-		..\x2p\util.c	\

-		..\x2p\walk.c

-

-CORE_NOCFG_H	=		\

-		..\av.h		\

-		..\cop.h	\

-		..\cv.h		\

-		..\dosish.h	\

-		..\embed.h	\

-		..\form.h	\

-		..\gv.h		\

-		..\handy.h	\

-		..\hv.h		\

-		..\iperlsys.h	\

-		..\mg.h		\

-		..\nostdio.h	\

-		..\op.h		\

-		..\opcode.h	\

-		..\perl.h	\

-		..\perlapi.h	\

-		..\perlsdio.h	\

-		..\perlsfio.h	\

-		..\perly.h	\

-		..\pp.h		\

-		..\proto.h	\

-		..\regexp.h	\

-		..\scope.h	\

-		..\sv.h		\

-		..\thread.h	\

-		..\unixish.h	\

-		..\utf8.h	\

-		..\util.h	\

-		..\warnings.h	\

-		..\XSUB.h	\

-		..\EXTERN.h	\

-		..\perlvars.h	\

-		..\intrpvar.h	\

-		..\thrdvar.h	\

-		.\include\dirent.h	\

-		.\include\netdb.h	\

-		.\include\sys\socket.h	\

-		.\win32.h

-

-CORE_H		= $(CORE_NOCFG_H) .\config.h

-

-MICROCORE_OBJ	= $(MICROCORE_SRC:.c=.obj)

-CORE_OBJ	= $(MICROCORE_OBJ) $(EXTRACORE_SRC:.c=.obj)

-WIN32_OBJ	= $(WIN32_SRC:.c=.obj)

-MINICORE_OBJ	= $(MICROCORE_OBJ:..\=.\mini\)	\

-		  $(MINIDIR)\miniperlmain$(o)	\

-		  $(MINIDIR)\perlio$(o)

-MINIWIN32_OBJ	= $(WIN32_OBJ:.\=.\mini\)

-MINI_OBJ	= $(MINICORE_OBJ) $(MINIWIN32_OBJ)

-DLL_OBJ		= $(DLL_SRC:.c=.obj)

-X2P_OBJ		= $(X2P_SRC:.c=.obj)

-

-PERLDLL_OBJ	= $(CORE_OBJ)

-PERLEXE_OBJ	= perlmain$(o)

-

-PERLDLL_OBJ	= $(PERLDLL_OBJ) $(WIN32_OBJ) $(DLL_OBJ)

-#PERLEXE_OBJ	= $(PERLEXE_OBJ) $(WIN32_OBJ) $(DLL_OBJ)

-

-!IF "$(USE_SETARGV)" != ""

-SETARGV_OBJ	= setargv$(o)

-!ENDIF

-

-DYNAMIC_EXT	= Socket IO Fcntl Opcode SDBM_File POSIX attrs Thread B re \

-		Data/Dumper Devel/Peek ByteLoader Devel/DProf File/Glob \

-		Sys/Hostname Storable

-STATIC_EXT	= DynaLoader

-NONXS_EXT	= Errno

-

-DYNALOADER	= $(EXTDIR)\DynaLoader\DynaLoader

-SOCKET		= $(EXTDIR)\Socket\Socket

-FCNTL		= $(EXTDIR)\Fcntl\Fcntl

-OPCODE		= $(EXTDIR)\Opcode\Opcode

-SDBM_FILE	= $(EXTDIR)\SDBM_File\SDBM_File

-IO		= $(EXTDIR)\IO\IO

-POSIX		= $(EXTDIR)\POSIX\POSIX

-ATTRS		= $(EXTDIR)\attrs\attrs

-THREAD		= $(EXTDIR)\Thread\Thread

-B		= $(EXTDIR)\B\B

-RE		= $(EXTDIR)\re\re

-DUMPER		= $(EXTDIR)\Data\Dumper\Dumper

-ERRNO		= $(EXTDIR)\Errno\Errno

-PEEK		= $(EXTDIR)\Devel\Peek\Peek

-BYTELOADER	= $(EXTDIR)\ByteLoader\ByteLoader

-DPROF		= $(EXTDIR)\Devel\DProf\DProf

-GLOB		= $(EXTDIR)\File\Glob\Glob

-HOSTNAME	= $(EXTDIR)\Sys\Hostname\Hostname

-STORABLE	= $(EXTDIR)\Storable\Storable

-

-SOCKET_DLL	= $(AUTODIR)\Socket\Socket.dll

-FCNTL_DLL	= $(AUTODIR)\Fcntl\Fcntl.dll

-OPCODE_DLL	= $(AUTODIR)\Opcode\Opcode.dll

-SDBM_FILE_DLL	= $(AUTODIR)\SDBM_File\SDBM_File.dll

-IO_DLL		= $(AUTODIR)\IO\IO.dll

-POSIX_DLL	= $(AUTODIR)\POSIX\POSIX.dll

-ATTRS_DLL	= $(AUTODIR)\attrs\attrs.dll

-THREAD_DLL	= $(AUTODIR)\Thread\Thread.dll

-B_DLL		= $(AUTODIR)\B\B.dll

-DUMPER_DLL	= $(AUTODIR)\Data\Dumper\Dumper.dll

-PEEK_DLL	= $(AUTODIR)\Devel\Peek\Peek.dll

-RE_DLL		= $(AUTODIR)\re\re.dll

-BYTELOADER_DLL	= $(AUTODIR)\ByteLoader\ByteLoader.dll

-DPROF_DLL	= $(AUTODIR)\Devel\DProf\DProf.dll

-GLOB_DLL	= $(AUTODIR)\File\Glob\Glob.dll

-HOSTNAME_DLL	= $(AUTODIR)\Sys\Hostname\Hostname.dll

-STORABLE_DLL	= $(AUTODIR)\Storable\Storable.dll

-

-ERRNO_PM	= $(LIBDIR)\Errno.pm

-

-EXTENSION_C	= 		\

-		$(SOCKET).c	\

-		$(FCNTL).c	\

-		$(OPCODE).c	\

-		$(SDBM_FILE).c	\

-		$(IO).c		\

-		$(POSIX).c	\

-		$(ATTRS).c	\

-		$(THREAD).c	\

-		$(RE).c		\

-		$(DUMPER).c	\

-		$(PEEK).c	\

-		$(B).c		\

-		$(BYTELOADER).c	\

-		$(DPROF).c	\

-		$(GLOB).c	\

-		$(HOSTNAME).c	\

-		$(STORABLE).c

-

-EXTENSION_DLL	= 		\

-		$(SOCKET_DLL)	\

-		$(FCNTL_DLL)	\

-		$(OPCODE_DLL)	\

-		$(SDBM_FILE_DLL)\

-		$(IO_DLL)	\

-		$(POSIX_DLL)	\

-		$(ATTRS_DLL)	\

-		$(DUMPER_DLL)	\

-		$(PEEK_DLL)	\

-		$(B_DLL)	\

-		$(RE_DLL)	\

-		$(THREAD_DLL)	\

-		$(BYTELOADER_DLL)	\

-		$(DPROF_DLL)	\

-		$(GLOB_DLL)	\

-		$(HOSTNAME_DLL)	\

-		$(STORABLE_DLL)

-

-EXTENSION_PM	=		\

-		$(ERRNO_PM)

-

-POD2HTML	= $(PODDIR)\pod2html

-POD2MAN		= $(PODDIR)\pod2man

-POD2LATEX	= $(PODDIR)\pod2latex

-POD2TEXT	= $(PODDIR)\pod2text

-

-CFG_VARS	=					\

-		"INST_DRV=$(INST_DRV)"			\

-		"INST_TOP=$(INST_TOP)"			\

-		"INST_VER=$(INST_VER)"			\

-		"INST_ARCH=$(INST_ARCH)"		\

-		"archname=$(ARCHNAME)"			\

-		"cc=$(CC)"				\

-		"ccflags=$(OPTIMIZE:"=\") $(DEFINES) $(BUILDOPT)"	\

-		"cf_email=$(EMAIL)"			\

-		"d_crypt=$(D_CRYPT)"			\

-		"d_mymalloc=$(PERL_MALLOC)"		\

-		"libs=$(LIBFILES)"			\

-		"incpath=$(CCINCDIR:"=\")"		\

-		"libperl=$(PERLIMPLIB:..\=)"		\

-		"libpth=$(CCLIBDIR:"=\");$(EXTRALIBDIRS:"=\")"	\

-		"libc=$(LIBC)"				\

-		"make=nmake"				\

-		"static_ext=$(STATIC_EXT)"		\

-		"dynamic_ext=$(DYNAMIC_EXT)"		\

-		"nonxs_ext=$(NONXS_EXT)"		\

-		"use5005threads=$(USE_5005THREADS)"	\

-		"useithreads=$(USE_ITHREADS)"		\

-		"usethreads=$(USE_5005THREADS)"		\

-		"usemultiplicity=$(USE_MULTI)"		\

-		"LINK_FLAGS=$(LINK_FLAGS:"=\")"		\

-		"optimize=$(OPTIMIZE:"=\")"

-

-#

-# Top targets

-#

-

-all : .\config.h $(GLOBEXE) $(MINIMOD) $(CONFIGPM) $(PERLEXE) \

-	$(X2P) $(EXTENSION_DLL) $(EXTENSION_PM)

-

-$(DYNALOADER)$(o) : $(DYNALOADER).c $(CORE_H) $(EXTDIR)\DynaLoader\dlutils.c

-

-#------------------------------------------------------------

-

-$(GLOBEXE) : perlglob$(o)

-	$(LINK32) $(LINK_FLAGS) $(LIBFILES) -out:$@ -subsystem:$(SUBSYS) \

-	    perlglob$(o) setargv$(o) 

-

-perlglob$(o)  : perlglob.c

-

-config.w32 : $(CFGSH_TMPL)

-	copy $(CFGSH_TMPL) config.w32

-

-.\config.h : $(CFGH_TMPL)

-	-del /f config.h

-	copy $(CFGH_TMPL) config.h

-

-..\config.sh : config.w32 $(MINIPERL) config_sh.PL

-	$(MINIPERL) -I..\lib config_sh.PL $(CFG_VARS) config.w32 > ..\config.sh

-

-# this target is for when changes to the main config.sh happen

-# edit config.{b,v,g}c and make this target once for each supported

-# compiler (e.g. `dmake CCTYPE=BORLAND regen_config_h`)

-regen_config_h:

-	perl config_sh.PL $(CFG_VARS) $(CFGSH_TMPL) > ..\config.sh

-	cd ..

-	-del /f perl.exe

-	perl configpm

-	cd win32

-	-del /f $(CFGH_TMPL)

-	-mkdir $(COREDIR)

-	-perl -I..\lib config_h.PL "INST_VER=$(INST_VER)"

-	rename config.h $(CFGH_TMPL)

-

-$(CONFIGPM) : $(MINIPERL) ..\config.sh config_h.PL ..\minimod.pl

-	cd .. && miniperl configpm

-	if exist lib\* $(RCOPY) lib\*.* ..\lib\$(NULL)

-	$(XCOPY) ..\*.h $(COREDIR)\*.*

-	$(XCOPY) *.h $(COREDIR)\*.*

-	$(XCOPY) ..\ext\re\re.pm $(LIBDIR)\*.*

-	$(RCOPY) include $(COREDIR)\*.*

-	$(MINIPERL) -I..\lib config_h.PL "INST_VER=$(INST_VER)" \

-	    || $(MAKE) /$(MAKEFLAGS) $(CONFIGPM)

-

-$(MINIPERL) : $(MINIDIR) $(MINI_OBJ)

-	$(LINK32) -subsystem:console -out:$@ @<<

-	$(LINK_FLAGS) $(LIBFILES) $(MINI_OBJ)

-<<

-

-$(MINIDIR) :

-	if not exist "$(MINIDIR)" mkdir "$(MINIDIR)"

-

-$(MINICORE_OBJ) : $(CORE_NOCFG_H)

-	$(CC) -c $(CFLAGS) -DPERL_EXTERNAL_GLOB $(OBJOUT_FLAG)$@ ..\$(*F).c

-

-$(MINIWIN32_OBJ) : $(CORE_NOCFG_H)

-	$(CC) -c $(CFLAGS) $(OBJOUT_FLAG)$@ $(*F).c

-

-# -DPERL_IMPLICIT_SYS needs C++ for perllib.c

-# This is the only file that depends on perlhost.h, vmem.h, and vdir.h

-!IF "$(USE_IMP_SYS)$(USE_OBJECT)" == "defineundef"

-perllib$(o)	: perllib.c .\perlhost.h .\vdir.h .\vmem.h

-	$(CC) -c -I. $(CFLAGS_O) $(CXX_FLAG) $(OBJOUT_FLAG)$@ perllib.c

-!ENDIF

-

-# 1. we don't want to rebuild miniperl.exe when config.h changes

-# 2. we don't want to rebuild miniperl.exe with non-default config.h

-$(MINI_OBJ)	: $(CORE_NOCFG_H)

-

-$(WIN32_OBJ)	: $(CORE_H)

-$(CORE_OBJ)	: $(CORE_H)

-$(DLL_OBJ)	: $(CORE_H)

-$(X2P_OBJ)	: $(CORE_H)

-

-perldll.def : $(MINIPERL) $(CONFIGPM) ..\global.sym ..\pp.sym ..\makedef.pl

-	$(MINIPERL) -w ..\makedef.pl PLATFORM=win32 $(OPTIMIZE) $(DEFINES) $(BUILDOPT) \

-	    CCTYPE=$(CCTYPE) > perldll.def

-

-$(PERLDLL): perldll.def $(PERLDLL_OBJ) $(PERLDLL_RES)

-	$(LINK32) -dll -def:perldll.def -base:0x28000000 -out:$@ @<<

-		$(LINK_FLAGS) $(DELAYLOAD) $(LIBFILES) $(PERLDLL_OBJ) $(PERLDLL_RES)

-<<

-	$(XCOPY) $(PERLIMPLIB) $(COREDIR)

-

-$(MINIMOD) : $(MINIPERL) ..\minimod.pl

-	cd .. && miniperl minimod.pl > lib\ExtUtils\Miniperl.pm

-

-..\x2p\a2p$(o) : ..\x2p\a2p.c

-	$(CC) -I..\x2p $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\a2p.c

-

-..\x2p\hash$(o) : ..\x2p\hash.c

-	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\hash.c

-

-..\x2p\str$(o) : ..\x2p\str.c

-	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\str.c

-

-..\x2p\util$(o) : ..\x2p\util.c

-	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\util.c

-

-..\x2p\walk$(o) : ..\x2p\walk.c

-	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\walk.c

-

-$(X2P) : $(MINIPERL) $(X2P_OBJ)

-	$(MINIPERL) ..\x2p\find2perl.PL

-	$(MINIPERL) ..\x2p\s2p.PL

-	$(LINK32) -subsystem:console -out:$@ @<<

-		$(LINK_FLAGS) $(LIBFILES) $(X2P_OBJ)

-<<

-

-perlmain.c : runperl.c 

-	copy runperl.c perlmain.c

-

-perlmain$(o) : perlmain.c

-	$(CC) $(CFLAGS_O) -UPERLDLL $(OBJOUT_FLAG)$@ -c perlmain.c

-

-$(PERLEXE): $(PERLDLL) $(CONFIGPM) $(PERLEXE_OBJ) $(PERLEXE_RES)

-	$(LINK32) -subsystem:console -out:$@ -stack:0x1000000 $(LINK_FLAGS) \

-	    $(LIBFILES) $(PERLEXE_OBJ) $(SETARGV_OBJ) $(PERLIMPLIB) $(PERLEXE_RES)

-	copy $(PERLEXE) $(WPERLEXE)

-	$(MINIPERL) -I..\lib bin\exetype.pl $(WPERLEXE) WINDOWS

-	copy splittree.pl .. 

-	$(MINIPERL) -I..\lib ..\splittree.pl "../LIB" $(AUTODIR)

-

-$(DYNALOADER).c: $(MINIPERL) $(EXTDIR)\DynaLoader\dl_win32.xs $(CONFIGPM)

-	if not exist $(AUTODIR) mkdir $(AUTODIR)

-	cd $(EXTDIR)\$(*B)

-	..\$(MINIPERL) -I..\..\lib $(*B)_pm.PL

-	..\$(MINIPERL) -I..\..\lib XSLoader_pm.PL

-	cd ..\..\win32

-	$(XCOPY) $(EXTDIR)\$(*B)\$(*B).pm $(LIBDIR)\$(NULL)

-	$(XCOPY) $(EXTDIR)\$(*B)\XSLoader.pm $(LIBDIR)\$(NULL)

-	cd $(EXTDIR)\$(*B)

-	$(XSUBPP) dl_win32.xs > $(*B).c

-	cd ..\..\win32

-

-$(EXTDIR)\DynaLoader\dl_win32.xs: dl_win32.xs

-	copy dl_win32.xs $(EXTDIR)\DynaLoader\dl_win32.xs

-

-$(DUMPER_DLL): $(PERLEXE) $(DUMPER).xs

-	cd $(EXTDIR)\Data\$(*B)

-	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\..\win32

-

-$(DPROF_DLL): $(PERLEXE) $(DPROF).xs

-	cd $(EXTDIR)\Devel\$(*B)

-	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\..\win32

-

-$(GLOB_DLL): $(PERLEXE) $(GLOB).xs

-	cd $(EXTDIR)\File\$(*B)

-	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\..\win32

-

-$(PEEK_DLL): $(PERLEXE) $(PEEK).xs

-	cd $(EXTDIR)\Devel\$(*B)

-	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\..\win32

-

-$(RE_DLL): $(PERLEXE) $(RE).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(B_DLL): $(PERLEXE) $(B).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(THREAD_DLL): $(PERLEXE) $(THREAD).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(ATTRS_DLL): $(PERLEXE) $(ATTRS).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(POSIX_DLL): $(PERLEXE) $(POSIX).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(IO_DLL): $(PERLEXE) $(IO).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(SDBM_FILE_DLL) : $(PERLEXE) $(SDBM_FILE).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(FCNTL_DLL): $(PERLEXE) $(FCNTL).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(OPCODE_DLL): $(PERLEXE) $(OPCODE).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(SOCKET_DLL): $(PERLEXE) $(SOCKET).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(HOSTNAME_DLL): $(PERLEXE) $(HOSTNAME).xs

-	cd $(EXTDIR)\Sys\$(*B)

-	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\..\win32

-

-$(BYTELOADER_DLL): $(PERLEXE) $(BYTELOADER).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(STORABLE_DLL): $(PERLEXE) $(STORABLE).xs

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-$(ERRNO_PM): $(PERLEXE) $(ERRNO)_pm.PL

-	cd $(EXTDIR)\$(*B)

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	$(MAKE)

-	cd ..\..\win32

-

-doc: $(PERLEXE)

-	$(PERLEXE) -I..\lib ..\installhtml --podroot=.. --htmldir=./html \

-	    --podpath=pod:lib:ext:utils --htmlroot="file://$(INST_HTML::=|)" \

-	    --libpod=perlfunc:perlguts:perlvar:perlrun:perlop --recurse

-

-utils: $(PERLEXE) $(X2P)

-	cd ..\utils

-	$(MAKE) PERL=$(MINIPERL)

-	cd ..\pod

-	copy ..\README.amiga .\perlamiga.pod

-	copy ..\README.cygwin .\perlcygwin.pod

-	copy ..\README.dos .\perldos.pod

-	copy ..\README.hpux .\perlhpux.pod

-	copy ..\README.machten .\perlmachten.pod

-	copy ..\README.os2 .\perlos2.pod

-	copy ..\vms\perlvms.pod .\perlvms.pod

-	copy ..\README.win32 .\perlwin32.pod

-	$(MAKE) -f ..\win32\pod.mak converters

-	cd ..\lib

-	$(PERLEXE) lib_pm.PL

-	cd ..\win32

-	$(PERLEXE) $(PL2BAT) $(UTILS)

-

-distclean: clean

-	-del /f $(MINIPERL) $(PERLEXE) $(PERLDLL) $(GLOBEXE) \

-		$(PERLIMPLIB) ..\miniperl.lib $(MINIMOD)

-	-del /f *.def *.map

-	-del /f $(EXTENSION_DLL) $(EXTENSION_PM)

-	-del /f $(EXTENSION_C) $(DYNALOADER).c $(ERRNO).pm

-	-del /f $(EXTDIR)\DynaLoader\dl_win32.xs

-	-del /f $(LIBDIR)\.exists $(LIBDIR)\attrs.pm $(LIBDIR)\DynaLoader.pm

-	-del /f $(LIBDIR)\XSLoader.pm

-	-del /f $(LIBDIR)\Fcntl.pm $(LIBDIR)\IO.pm $(LIBDIR)\Opcode.pm

-	-del /f $(LIBDIR)\ops.pm $(LIBDIR)\Safe.pm $(LIBDIR)\Thread.pm

-	-del /f $(LIBDIR)\SDBM_File.pm $(LIBDIR)\Socket.pm $(LIBDIR)\POSIX.pm

-	-del /f $(LIBDIR)\B.pm $(LIBDIR)\O.pm $(LIBDIR)\re.pm

-	-del /f $(LIBDIR)\Data\Dumper.pm $(LIBDIR)\ByteLoader.pm

-	-del /f $(LIBDIR)\Devel\Peek.pm $(LIBDIR)\Devel\DProf.pm

-	-del /f $(LIBDIR)\File\Glob.pm

-	-del /f $(LIBDIR)\Storable.pm

-	-if exist $(LIBDIR)\IO rmdir /s /q $(LIBDIR)\IO || rmdir /s $(LIBDIR)\IO

-	-if exist $(LIBDIR)\Thread rmdir /s /q $(LIBDIR)\Thread || rmdir /s $(LIBDIR)\Thread

-	-if exist $(LIBDIR)\B rmdir /s /q $(LIBDIR)\B || rmdir /s $(LIBDIR)\B

-	-if exist $(LIBDIR)\Data rmdir /s /q $(LIBDIR)\Data || rmdir /s $(LIBDIR)\Data

-	-del /f $(PODDIR)\*.html

-	-del /f $(PODDIR)\*.bat

-	cd ..\utils

-	-del /f h2ph splain perlbug pl2pm c2ph h2xs perldoc dprofpp

-	-del /f *.bat

-	cd ..\win32

-	cd ..\x2p

-	-del /f find2perl s2p

-	-del /f *.bat

-	cd ..\win32

-	-del /f ..\config.sh ..\splittree.pl perlmain.c dlutils.c config.h.new

-	-del /f $(CONFIGPM)

-	-del /f bin\*.bat

-	cd $(EXTDIR)

-	-del /s *.lib *.def *.map *.pdb *.bs Makefile *$(o) pm_to_blib

-	cd ..\win32

-	-if exist $(AUTODIR) rmdir /s /q $(AUTODIR) || rmdir /s $(AUTODIR)

-	-if exist $(COREDIR) rmdir /s /q $(COREDIR) || rmdir /s $(COREDIR)

-

-install : all installbare installhtml

-

-installbare : utils

-	$(PERLEXE) ..\installperl

-	if exist $(WPERLEXE) $(XCOPY) $(WPERLEXE) $(INST_BIN)\*.*

-	$(XCOPY) $(GLOBEXE) $(INST_BIN)\*.*

-	$(XCOPY) bin\*.bat $(INST_SCRIPT)\*.*

-

-installhtml : doc

-	$(RCOPY) html\*.* $(INST_HTML)\*.*

-

-inst_lib : $(CONFIGPM)

-	copy splittree.pl .. 

-	$(MINIPERL) -I..\lib ..\splittree.pl "../LIB" $(AUTODIR)

-	$(RCOPY) ..\lib $(INST_LIB)\*.*

-

-minitest : $(MINIPERL) $(GLOBEXE) $(CONFIGPM) utils

-	$(XCOPY) $(MINIPERL) ..\t\perl.exe

-	$(XCOPY) $(GLOBEXE) ..\t\$(NULL)

-	attrib -r ..\t\*.*

-	copy test ..\t

-	cd ..\t

-	$(MINIPERL) -I..\lib test base/*.t comp/*.t cmd/*.t io/*.t op/*.t pragma/*.t

-	cd ..\win32

-

-test-prep : all utils

-	$(XCOPY) $(PERLEXE) ..\t\$(NULL)

-	$(XCOPY) $(PERLDLL) ..\t\$(NULL)

-	$(XCOPY) $(GLOBEXE) ..\t\$(NULL)

-

-test : test-prep

-	cd ..\t

-	$(PERLEXE) -I..\lib harness

-	cd ..\win32

-

-test-notty : test-prep

-	set PERL_SKIP_TTY_TEST=1

-	cd ..\t

-	$(PERLEXE) -I..\lib harness

-	cd ..\win32

-

-test-wide : test-prep

-	set HARNESS_PERL_SWITCHES=-C

-	cd ..\t

-	$(PERLEXE) -I..\lib harness

-	cd ..\win32

-

-test-wide-notty : test-prep

-	set PERL_SKIP_TTY_TEST=1

-	set HARNESS_PERL_SWITCHES=-C

-	cd ..\t

-	$(PERLEXE) -I..\lib harness

-	cd ..\win32

-

-clean : 

-	-@erase miniperlmain$(o)

-	-@erase $(MINIPERL)

-	-@erase perlglob$(o)

-	-@erase perlmain$(o)

-	-@erase config.w32

-	-@erase /f config.h

-	-@erase $(GLOBEXE)

-	-@erase $(PERLEXE)

-	-@erase $(WPERLEXE)

-	-@erase $(PERLDLL)

-	-@erase $(CORE_OBJ)

-	-if exist $(MINIDIR) rmdir /s /q $(MINIDIR) || rmdir /s $(MINIDIR)

-	-@erase $(WIN32_OBJ)

-	-@erase $(DLL_OBJ)

-	-@erase $(X2P_OBJ)

-	-@erase ..\*$(o) ..\*.lib ..\*.exp *$(o) *.lib *.exp *.res

-	-@erase ..\t\*.exe ..\t\*.dll ..\t\*.bat

-	-@erase ..\x2p\*.exe ..\x2p\*.bat

-	-@erase *.ilk

-	-@erase *.pdb

- 

-# Handy way to run perlbug -ok without having to install and run the

-# installed perlbug. We don't re-run the tests here - we trust the user.

-# Please *don't* use this unless all tests pass.

-# If you want to report test failures, use "nmake nok" instead.

-ok: utils

-	$(PERLEXE) -I..\lib ..\utils\perlbug -ok -s "(UNINSTALLED)"

-

-okfile: utils

-	$(PERLEXE) -I..\lib ..\utils\perlbug -ok -s "(UNINSTALLED)" -F perl.ok

- 

-nok: utils

-	$(PERLEXE) -I..\lib ..\utils\perlbug -nok -s "(UNINSTALLED)"

- 

-nokfile: utils

-	$(PERLEXE) -I..\lib ..\utils\perlbug -nok -s "(UNINSTALLED)" -F perl.nok

+#
+# Makefile to build perl on Windows NT using Microsoft NMAKE.
+#
+# This is set up to build a perl.exe that runs off a shared library
+# (perl56.dll).  Also makes individual DLLs for the XS extensions.
+#
+
+##
+## Make sure you read README.win32 *before* you mess with anything here!
+##
+
+##
+## Build configuration.  Edit the values below to suit your needs.
+##
+
+#
+# Set these to wherever you want "nmake install" to put your
+# newly built perl.
+#
+INST_DRV	= c:
+INST_TOP	= $(INST_DRV)\perl
+
+#
+# Comment this out if you DON'T want your perl installation to be versioned.
+# This means that the new installation will overwrite any files from the
+# old installation at the same INST_TOP location.  Leaving it enabled is
+# the safest route, as perl adds the extra version directory to all the
+# locations it installs files to.  If you disable it, an alternative
+# versioned installation can be obtained by setting INST_TOP above to a
+# path that includes an arbitrary version string.
+#
+INST_VER	= \5.6.0
+
+#
+# Comment this out if you DON'T want your perl installation to have
+# architecture specific components.  This means that architecture-
+# specific files will be installed along with the architecture-neutral
+# files.  Leaving it enabled is safer and more flexible, in case you
+# want to build multiple flavors of perl and install them together in
+# the same location.  Commenting it out gives you a simpler
+# installation that is easier to understand for beginners.
+#
+INST_ARCH	= \$(ARCHNAME)
+
+#
+# uncomment to enable multiple interpreters.  This is need for fork()
+# emulation.
+#
+#USE_MULTI	= define
+
+#
+# Beginnings of interpreter cloning/threads; still very incomplete.
+# This should be enabled to get the fork() emulation.  This needs
+# USE_MULTI as well.
+#
+#USE_ITHREADS	= define
+
+#
+# uncomment to enable the implicit "host" layer for all system calls
+# made by perl.  This needs USE_MULTI above.  This is also needed to
+# get fork().
+#
+#USE_IMP_SYS	= define
+
+#
+# WARNING! This option is deprecated and will eventually go away (enable
+# USE_ITHREADS instead).
+#
+# uncomment to enable threads-capabilities.  This is incompatible with
+# USE_ITHREADS, and is only here for people who may have come to rely
+# on the experimental Thread support that was in 5.005.
+#
+#USE_5005THREADS= define
+
+#
+# WARNING! This option is deprecated and will eventually go away (enable
+# USE_MULTI instead).
+#
+# uncomment next line if you want to use the PERL_OBJECT build option.
+# DO NOT ENABLE unless you have legacy code that relies on the C++
+# CPerlObj class that was available in 5.005.  This cannot be enabled
+# if you ask for USE_5005THREADS above.
+#
+#USE_OBJECT	= define
+
+#
+# uncomment one of the following lines if you are using either
+# Visual C++ 2.x or Visual C++ 6.x (aka Visual Studio 98)
+#
+#CCTYPE		= MSVC20
+#CCTYPE		= MSVC60
+
+#
+# uncomment next line if you want debug version of perl (big,slow)
+#
+#CFG		= Debug
+
+#
+# uncomment to enable use of PerlCRT.DLL when using the Visual C compiler.
+# It has patches that fix known bugs in older versions of MSVCRT.DLL.
+# This currently requires VC 5.0 with Service Pack 3 or later.
+# Get it from CPAN at http://www.perl.com/CPAN/authors/id/D/DO/DOUGL/
+# and follow the directions in the package to install.
+#
+# Not recommended if you have VC 6.x and you're not running Windows 9x.
+#
+#USE_PERLCRT	= define
+
+#
+# uncomment to enable linking with setargv.obj under the Visual C
+# compiler. Setting this options enables perl to expand wildcards in
+# arguments, but it may be harder to use alternate methods like
+# File::DosGlob that are more powerful.  This option is supported only with
+# Visual C.
+#
+#USE_SETARGV	= define
+
+#
+# if you have the source for des_fcrypt(), uncomment this and make sure the
+# file exists (see README.win32).  File should be located in the same
+# directory as this file.
+#
+#CRYPT_SRC	= fcrypt.c
+
+#
+# if you didn't set CRYPT_SRC and if you have des_fcrypt() available in a
+# library, uncomment this, and make sure the library exists (see README.win32)
+# Specify the full pathname of the library.
+#
+#CRYPT_LIB	= fcrypt.lib
+
+#
+# set this if you wish to use perl's malloc
+# WARNING: Turning this on/off WILL break binary compatibility with extensions
+# you may have compiled with/without it.  Be prepared to recompile all
+# extensions if you change the default.  Currently, this cannot be enabled
+# if you ask for USE_IMP_SYS above.
+#
+#PERL_MALLOC	= define
+
+#
+# set the install locations of the compiler include/libraries
+# Running VCVARS32.BAT is *required* when using Visual C.
+# Some versions of Visual C don't define MSVCDIR in the environment,
+# so you may have to set CCHOME explicitly (spaces in the path name should
+# not be quoted)
+#
+#CCHOME		= f:\msvc20
+CCHOME		= $(MSVCDIR)
+CCINCDIR	= $(CCHOME)\include
+CCLIBDIR	= $(CCHOME)\lib
+
+#
+# Additional compiler flags can be specified here.
+#
+
+#
+# This should normally be disabled.  Adding -DPERL_POLLUTE enables support
+# for old symbols by default, at the expense of extreme pollution.  You most
+# probably just want to build modules that won't compile with
+#         perl Makefile.PL POLLUTE=1
+# instead of enabling this.  Please report such modules to the respective
+# authors.
+#
+#BUILDOPT	= $(BUILDOPT) -DPERL_POLLUTE
+
+#
+# This should normally be disabled.  Enabling it will disable the File::Glob
+# implementation of CORE::glob.
+#
+#BUILDOPT	= $(BUILDOPT) -DPERL_EXTERNAL_GLOB
+
+#
+# This should normally be disabled.  Enabling it causes perl to read scripts
+# in text mode (which is the 5.005 behavior) and will break ByteLoader.
+#BUILDOPT	= $(BUILDOPT) -DPERL_TEXTMODE_SCRIPTS
+
+#
+# specify semicolon-separated list of extra directories that modules will
+# look for libraries (spaces in path names need not be quoted)
+#
+EXTRALIBDIRS	=
+
+#
+# set this to your email address (perl will guess a value from
+# from your loginname and your hostname, which may not be right)
+#
+#EMAIL		=
+
+##
+## Build configuration ends.
+##
+
+##################### CHANGE THESE ONLY IF YOU MUST #####################
+
+!IF "$(CRYPT_SRC)$(CRYPT_LIB)" == ""
+D_CRYPT		= undef
+!ELSE
+D_CRYPT		= define
+CRYPT_FLAG	= -DHAVE_DES_FCRYPT
+!ENDIF
+
+!IF "$(USE_OBJECT)" == "define"
+PERL_MALLOC	= undef
+USE_5005THREADS	= undef
+USE_MULTI	= undef
+USE_IMP_SYS	= define
+!ENDIF
+
+!IF "$(PERL_MALLOC)" == ""
+PERL_MALLOC	= undef
+!ENDIF
+
+!IF "$(USE_5005THREADS)" == ""
+USE_5005THREADS	= undef
+!ENDIF
+
+!IF "$(USE_5005THREADS)" == "define"
+USE_ITHREADS	= undef
+!ENDIF
+
+!IF "$(USE_IMP_SYS)" == "define"
+PERL_MALLOC	= undef
+!ENDIF
+
+!IF "$(USE_MULTI)" == ""
+USE_MULTI	= undef
+!ENDIF
+
+!IF "$(USE_OBJECT)" == ""
+USE_OBJECT	= undef
+!ENDIF
+
+!IF "$(USE_ITHREADS)" == ""
+USE_ITHREADS	= undef
+!ENDIF
+
+!IF "$(USE_IMP_SYS)" == ""
+USE_IMP_SYS	= undef
+!ENDIF
+
+!IF "$(USE_PERLCRT)" == ""
+USE_PERLCRT	= undef
+!ENDIF
+
+!IF "$(USE_IMP_SYS)$(USE_MULTI)$(USE_5005THREADS)$(USE_OBJECT)" == "defineundefundefundef"
+USE_MULTI	= define
+!ENDIF
+
+!IF "$(USE_ITHREADS)$(USE_MULTI)$(USE_OBJECT)" == "defineundefundef"
+USE_MULTI	= define
+USE_5005THREADS	= undef
+!ENDIF
+
+!IF "$(USE_MULTI)$(USE_5005THREADS)$(USE_OBJECT)" != "undefundefundef"
+BUILDOPT	= $(BUILDOPT) -DPERL_IMPLICIT_CONTEXT
+!ENDIF
+
+!IF "$(USE_IMP_SYS)" != "undef"
+BUILDOPT	= $(BUILDOPT) -DPERL_IMPLICIT_SYS
+!ENDIF
+
+!IF "$(PROCESSOR_ARCHITECTURE)" == ""
+PROCESSOR_ARCHITECTURE	= x86
+!ENDIF
+
+!IF "$(USE_OBJECT)" == "define"
+ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-object
+!ELSE
+!IF "$(USE_5005THREADS)" == "define"
+ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-thread
+!ELSE
+!IF "$(USE_MULTI)" == "define"
+ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-multi
+!ELSE
+ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)
+!ENDIF
+!ENDIF
+!ENDIF
+
+!IF "$(USE_ITHREADS)" == "define"
+ARCHNAME	= $(ARCHNAME)-thread
+!ENDIF
+
+# Visual Studio 98 specific
+!IF "$(CCTYPE)" == "MSVC60"
+
+# VC 6.0 can load the socket dll on demand.  Makes the test suite
+# run in about 10% less time.
+DELAYLOAD	= -DELAYLOAD:wsock32.dll -DELAYLOAD:shell32.dll delayimp.lib 
+
+# VC 6.0 seems capable of compiling perl correctly with optimizations
+# enabled.  Anything earlier fails tests.
+!IF "$(CFG)" == ""
+CFG		= Optimize
+!ENDIF
+!ENDIF
+
+ARCHDIR		= ..\lib\$(ARCHNAME)
+COREDIR		= ..\lib\CORE
+AUTODIR		= ..\lib\auto
+LIBDIR		= ..\lib
+EXTDIR		= ..\ext
+PODDIR		= ..\pod
+EXTUTILSDIR	= $(LIBDIR)\ExtUtils
+
+#
+INST_SCRIPT	= $(INST_TOP)$(INST_VER)\bin
+INST_BIN	= $(INST_SCRIPT)$(INST_ARCH)
+INST_LIB	= $(INST_TOP)$(INST_VER)\lib
+INST_ARCHLIB	= $(INST_LIB)$(INST_ARCH)
+INST_COREDIR	= $(INST_ARCHLIB)\CORE
+INST_POD	= $(INST_LIB)\pod
+INST_HTML	= $(INST_POD)\html
+
+#
+# Programs to compile, build .lib files and link
+#
+
+CC		= cl
+LINK32		= link
+LIB32		= $(LINK32) -lib
+RSC		= rc
+
+#
+# Options
+#
+
+INCLUDES	= -I$(COREDIR) -I.\include -I. -I..
+#PCHFLAGS	= -Fpc:\temp\vcmoduls.pch -YX 
+DEFINES		= -DWIN32 -D_CONSOLE -DNO_STRICT $(CRYPT_FLAG)
+LOCDEFS		= -DPERLDLL -DPERL_CORE
+SUBSYS		= console
+CXX_FLAG	= -TP -GX
+
+!IF "$(USE_PERLCRT)" != "define"
+LIBC	= msvcrt.lib
+!ELSE
+LIBC	= PerlCRT.lib
+!ENDIF
+
+PERLEXE_RES	=
+PERLDLL_RES	=
+
+!IF  "$(CFG)" == "Debug"
+!  IF "$(CCTYPE)" == "MSVC20"
+OPTIMIZE	= -Od -MD -Z7 -DDEBUGGING
+!  ELSE
+OPTIMIZE	= -Od -MD -Zi -DDEBUGGING
+!  ENDIF
+LINK_DBG	= -debug -pdb:none
+!ELSE
+!  IF  "$(CFG)" == "Optimize"
+# -O1 yields smaller code, which turns out to be faster than -O2
+#OPTIMIZE	= -O2 -MD -DNDEBUG
+OPTIMIZE	= -O1 -MD -DNDEBUG
+!  ELSE
+OPTIMIZE	= -Od -MD -DNDEBUG
+!  ENDIF
+LINK_DBG	= -release
+!ENDIF
+
+!IF "$(USE_OBJECT)" == "define"
+OPTIMIZE	= $(OPTIMIZE) $(CXX_FLAG)
+BUILDOPT	= $(BUILDOPT) -DPERL_OBJECT
+!ENDIF
+
+!IF "$(USE_PERLCRT)" != "define"
+BUILDOPT	= $(BUILDOPT) -DPERL_MSVCRT_READFIX
+!ENDIF
+
+LIBBASEFILES	= $(CRYPT_LIB) \
+		oldnames.lib kernel32.lib user32.lib gdi32.lib winspool.lib \
+		comdlg32.lib advapi32.lib shell32.lib ole32.lib oleaut32.lib \
+		netapi32.lib uuid.lib wsock32.lib mpr.lib winmm.lib \
+		version.lib odbc32.lib odbccp32.lib
+
+# we add LIBC here, since we may be using PerlCRT.dll
+LIBFILES	= $(LIBBASEFILES) $(LIBC)
+
+CFLAGS		= -nologo -Gf -W3 $(INCLUDES) $(DEFINES) $(LOCDEFS) \
+		$(PCHFLAGS) $(OPTIMIZE)
+LINK_FLAGS	= -nologo -nodefaultlib $(LINK_DBG) \
+		-libpath:"$(INST_COREDIR)" \
+		-machine:$(PROCESSOR_ARCHITECTURE)
+OBJOUT_FLAG	= -Fo
+EXEOUT_FLAG	= -Fe
+
+CFLAGS_O	= $(CFLAGS) $(BUILDOPT)
+
+#################### do not edit below this line #######################
+############# NO USER-SERVICEABLE PARTS BEYOND THIS POINT ##############
+
+o = .obj
+
+#
+# Rules
+# 
+
+.SUFFIXES : .c $(o) .dll .lib .exe .rc .res
+
+.c$(o):
+	$(CC) -c -I$(<D) $(CFLAGS_O) $(OBJOUT_FLAG)$@ $<
+
+.y.c:
+	$(NOOP)
+
+$(o).dll:
+	$(LINK32) -dll -subsystem:windows -implib:$(*B).lib -def:$(*B).def \
+	    -out:$@ $(LINK_FLAGS) $(LIBFILES) $< $(LIBPERL)  
+
+.rc.res:
+	$(RSC) -i.. $<
+
+#
+# various targets
+PERLIMPLIB	= ..\perl56.lib
+PERLDLL		= ..\perl56.dll
+
+MINIPERL	= ..\miniperl.exe
+MINIDIR		= .\mini
+PERLEXE		= ..\perl.exe
+WPERLEXE	= ..\wperl.exe
+GLOBEXE		= ..\perlglob.exe
+CONFIGPM	= ..\lib\Config.pm
+MINIMOD		= ..\lib\ExtUtils\Miniperl.pm
+X2P		= ..\x2p\a2p.exe
+
+PL2BAT		= bin\pl2bat.pl
+GLOBBAT		= bin\perlglob.bat
+
+UTILS		=			\
+		..\utils\h2ph		\
+		..\utils\splain		\
+		..\utils\dprofpp	\
+		..\utils\perlbug	\
+		..\utils\pl2pm 		\
+		..\utils\c2ph		\
+		..\utils\h2xs		\
+		..\utils\perldoc	\
+		..\utils\perlcc		\
+		..\pod\checkpods	\
+		..\pod\pod2html		\
+		..\pod\pod2latex	\
+		..\pod\pod2man		\
+		..\pod\pod2text		\
+		..\pod\pod2usage	\
+		..\pod\podchecker	\
+		..\pod\podselect	\
+		..\x2p\find2perl	\
+		..\x2p\s2p		\
+		bin\exetype.pl		\
+		bin\runperl.pl		\
+		bin\pl2bat.pl		\
+		bin\perlglob.pl		\
+		bin\search.pl
+
+MAKE		= nmake -nologo
+
+CFGSH_TMPL	= config.vc
+CFGH_TMPL	= config_H.vc
+
+XCOPY		= xcopy /f /r /i /d
+RCOPY		= xcopy /f /r /i /e /d
+NOOP		= @echo
+NULL		=
+
+#
+# filenames given to xsubpp must have forward slashes (since it puts
+# full pathnames in #line strings)
+XSUBPP		= ..\$(MINIPERL) -I..\..\lib ..\$(EXTUTILSDIR)\xsubpp \
+		-C++ -prototypes
+
+MICROCORE_SRC	=		\
+		..\av.c		\
+		..\deb.c	\
+		..\doio.c	\
+		..\doop.c	\
+		..\dump.c	\
+		..\globals.c	\
+		..\gv.c		\
+		..\hv.c		\
+		..\mg.c		\
+		..\op.c		\
+		..\perl.c	\
+		..\perlapi.c	\
+		..\perly.c	\
+		..\pp.c		\
+		..\pp_ctl.c	\
+		..\pp_hot.c	\
+		..\pp_sys.c	\
+		..\regcomp.c	\
+		..\regexec.c	\
+		..\run.c	\
+		..\scope.c	\
+		..\sv.c		\
+		..\taint.c	\
+		..\toke.c	\
+		..\universal.c	\
+		..\utf8.c	\
+		..\util.c	\
+		..\xsutils.c
+
+EXTRACORE_SRC	= $(EXTRACORE_SRC) perllib.c
+
+!IF "$(PERL_MALLOC)" == "define"
+EXTRACORE_SRC	= $(EXTRACORE_SRC) ..\malloc.c
+!ENDIF
+
+!IF "$(USE_OBJECT)" != "define"
+EXTRACORE_SRC	= $(EXTRACORE_SRC) ..\perlio.c
+!ENDIF
+
+WIN32_SRC	=		\
+		.\win32.c	\
+		.\win32sck.c	\
+		.\win32thread.c 
+
+!IF "$(CRYPT_SRC)" != ""
+WIN32_SRC	= $(WIN32_SRC) .\$(CRYPT_SRC)
+!ENDIF
+
+DLL_SRC		= $(DYNALOADER).c
+
+X2P_SRC		=		\
+		..\x2p\a2p.c	\
+		..\x2p\hash.c	\
+		..\x2p\str.c	\
+		..\x2p\util.c	\
+		..\x2p\walk.c
+
+CORE_NOCFG_H	=		\
+		..\av.h		\
+		..\cop.h	\
+		..\cv.h		\
+		..\dosish.h	\
+		..\embed.h	\
+		..\form.h	\
+		..\gv.h		\
+		..\handy.h	\
+		..\hv.h		\
+		..\iperlsys.h	\
+		..\mg.h		\
+		..\nostdio.h	\
+		..\op.h		\
+		..\opcode.h	\
+		..\perl.h	\
+		..\perlapi.h	\
+		..\perlsdio.h	\
+		..\perlsfio.h	\
+		..\perly.h	\
+		..\pp.h		\
+		..\proto.h	\
+		..\regexp.h	\
+		..\scope.h	\
+		..\sv.h		\
+		..\thread.h	\
+		..\unixish.h	\
+		..\utf8.h	\
+		..\util.h	\
+		..\warnings.h	\
+		..\XSUB.h	\
+		..\EXTERN.h	\
+		..\perlvars.h	\
+		..\intrpvar.h	\
+		..\thrdvar.h	\
+		.\include\dirent.h	\
+		.\include\netdb.h	\
+		.\include\sys\socket.h	\
+		.\win32.h
+
+CORE_H		= $(CORE_NOCFG_H) .\config.h
+
+MICROCORE_OBJ	= $(MICROCORE_SRC:.c=.obj)
+CORE_OBJ	= $(MICROCORE_OBJ) $(EXTRACORE_SRC:.c=.obj)
+WIN32_OBJ	= $(WIN32_SRC:.c=.obj)
+MINICORE_OBJ	= $(MICROCORE_OBJ:..\=.\mini\)	\
+		  $(MINIDIR)\miniperlmain$(o)	\
+		  $(MINIDIR)\perlio$(o)
+MINIWIN32_OBJ	= $(WIN32_OBJ:.\=.\mini\)
+MINI_OBJ	= $(MINICORE_OBJ) $(MINIWIN32_OBJ)
+DLL_OBJ		= $(DLL_SRC:.c=.obj)
+X2P_OBJ		= $(X2P_SRC:.c=.obj)
+
+PERLDLL_OBJ	= $(CORE_OBJ)
+PERLEXE_OBJ	= perlmain$(o)
+
+PERLDLL_OBJ	= $(PERLDLL_OBJ) $(WIN32_OBJ) $(DLL_OBJ)
+#PERLEXE_OBJ	= $(PERLEXE_OBJ) $(WIN32_OBJ) $(DLL_OBJ)
+
+!IF "$(USE_SETARGV)" != ""
+SETARGV_OBJ	= setargv$(o)
+!ENDIF
+
+DYNAMIC_EXT	= Socket IO Fcntl Opcode SDBM_File POSIX attrs Thread B re \
+		Data/Dumper Devel/Peek ByteLoader Devel/DProf File/Glob \
+		Sys/Hostname Storable
+STATIC_EXT	= DynaLoader
+NONXS_EXT	= Errno
+
+DYNALOADER	= $(EXTDIR)\DynaLoader\DynaLoader
+SOCKET		= $(EXTDIR)\Socket\Socket
+FCNTL		= $(EXTDIR)\Fcntl\Fcntl
+OPCODE		= $(EXTDIR)\Opcode\Opcode
+SDBM_FILE	= $(EXTDIR)\SDBM_File\SDBM_File
+IO		= $(EXTDIR)\IO\IO
+POSIX		= $(EXTDIR)\POSIX\POSIX
+ATTRS		= $(EXTDIR)\attrs\attrs
+THREAD		= $(EXTDIR)\Thread\Thread
+B		= $(EXTDIR)\B\B
+RE		= $(EXTDIR)\re\re
+DUMPER		= $(EXTDIR)\Data\Dumper\Dumper
+ERRNO		= $(EXTDIR)\Errno\Errno
+PEEK		= $(EXTDIR)\Devel\Peek\Peek
+BYTELOADER	= $(EXTDIR)\ByteLoader\ByteLoader
+DPROF		= $(EXTDIR)\Devel\DProf\DProf
+GLOB		= $(EXTDIR)\File\Glob\Glob
+HOSTNAME	= $(EXTDIR)\Sys\Hostname\Hostname
+STORABLE	= $(EXTDIR)\Storable\Storable
+
+SOCKET_DLL	= $(AUTODIR)\Socket\Socket.dll
+FCNTL_DLL	= $(AUTODIR)\Fcntl\Fcntl.dll
+OPCODE_DLL	= $(AUTODIR)\Opcode\Opcode.dll
+SDBM_FILE_DLL	= $(AUTODIR)\SDBM_File\SDBM_File.dll
+IO_DLL		= $(AUTODIR)\IO\IO.dll
+POSIX_DLL	= $(AUTODIR)\POSIX\POSIX.dll
+ATTRS_DLL	= $(AUTODIR)\attrs\attrs.dll
+THREAD_DLL	= $(AUTODIR)\Thread\Thread.dll
+B_DLL		= $(AUTODIR)\B\B.dll
+DUMPER_DLL	= $(AUTODIR)\Data\Dumper\Dumper.dll
+PEEK_DLL	= $(AUTODIR)\Devel\Peek\Peek.dll
+RE_DLL		= $(AUTODIR)\re\re.dll
+BYTELOADER_DLL	= $(AUTODIR)\ByteLoader\ByteLoader.dll
+DPROF_DLL	= $(AUTODIR)\Devel\DProf\DProf.dll
+GLOB_DLL	= $(AUTODIR)\File\Glob\Glob.dll
+HOSTNAME_DLL	= $(AUTODIR)\Sys\Hostname\Hostname.dll
+STORABLE_DLL	= $(AUTODIR)\Storable\Storable.dll
+
+ERRNO_PM	= $(LIBDIR)\Errno.pm
+
+EXTENSION_C	= 		\
+		$(SOCKET).c	\
+		$(FCNTL).c	\
+		$(OPCODE).c	\
+		$(SDBM_FILE).c	\
+		$(IO).c		\
+		$(POSIX).c	\
+		$(ATTRS).c	\
+		$(THREAD).c	\
+		$(RE).c		\
+		$(DUMPER).c	\
+		$(PEEK).c	\
+		$(B).c		\
+		$(BYTELOADER).c	\
+		$(DPROF).c	\
+		$(GLOB).c	\
+		$(HOSTNAME).c	\
+		$(STORABLE).c
+
+EXTENSION_DLL	= 		\
+		$(SOCKET_DLL)	\
+		$(FCNTL_DLL)	\
+		$(OPCODE_DLL)	\
+		$(SDBM_FILE_DLL)\
+		$(IO_DLL)	\
+		$(POSIX_DLL)	\
+		$(ATTRS_DLL)	\
+		$(DUMPER_DLL)	\
+		$(PEEK_DLL)	\
+		$(B_DLL)	\
+		$(RE_DLL)	\
+		$(THREAD_DLL)	\
+		$(BYTELOADER_DLL)	\
+		$(DPROF_DLL)	\
+		$(GLOB_DLL)	\
+		$(HOSTNAME_DLL)	\
+		$(STORABLE_DLL)
+
+EXTENSION_PM	=		\
+		$(ERRNO_PM)
+
+POD2HTML	= $(PODDIR)\pod2html
+POD2MAN		= $(PODDIR)\pod2man
+POD2LATEX	= $(PODDIR)\pod2latex
+POD2TEXT	= $(PODDIR)\pod2text
+
+CFG_VARS	=					\
+		"INST_DRV=$(INST_DRV)"			\
+		"INST_TOP=$(INST_TOP)"			\
+		"INST_VER=$(INST_VER)"			\
+		"INST_ARCH=$(INST_ARCH)"		\
+		"archname=$(ARCHNAME)"			\
+		"cc=$(CC)"				\
+		"ccflags=$(OPTIMIZE:"=\") $(DEFINES) $(BUILDOPT)"	\
+		"cf_email=$(EMAIL)"			\
+		"d_crypt=$(D_CRYPT)"			\
+		"d_mymalloc=$(PERL_MALLOC)"		\
+		"libs=$(LIBFILES)"			\
+		"incpath=$(CCINCDIR:"=\")"		\
+		"libperl=$(PERLIMPLIB:..\=)"		\
+		"libpth=$(CCLIBDIR:"=\");$(EXTRALIBDIRS:"=\")"	\
+		"libc=$(LIBC)"				\
+		"make=nmake"				\
+		"static_ext=$(STATIC_EXT)"		\
+		"dynamic_ext=$(DYNAMIC_EXT)"		\
+		"nonxs_ext=$(NONXS_EXT)"		\
+		"use5005threads=$(USE_5005THREADS)"	\
+		"useithreads=$(USE_ITHREADS)"		\
+		"usethreads=$(USE_5005THREADS)"		\
+		"usemultiplicity=$(USE_MULTI)"		\
+		"LINK_FLAGS=$(LINK_FLAGS:"=\")"		\
+		"optimize=$(OPTIMIZE:"=\")"
+
+#
+# Top targets
+#
+
+all : .\config.h $(GLOBEXE) $(MINIMOD) $(CONFIGPM) $(PERLEXE) \
+	$(X2P) $(EXTENSION_DLL) $(EXTENSION_PM)
+
+$(DYNALOADER)$(o) : $(DYNALOADER).c $(CORE_H) $(EXTDIR)\DynaLoader\dlutils.c
+
+#------------------------------------------------------------
+
+$(GLOBEXE) : perlglob$(o)
+	$(LINK32) $(LINK_FLAGS) $(LIBFILES) -out:$@ -subsystem:$(SUBSYS) \
+	    perlglob$(o) setargv$(o) 
+
+perlglob$(o)  : perlglob.c
+
+config.w32 : $(CFGSH_TMPL)
+	copy $(CFGSH_TMPL) config.w32
+
+.\config.h : $(CFGH_TMPL)
+	-del /f config.h
+	copy $(CFGH_TMPL) config.h
+
+..\config.sh : config.w32 $(MINIPERL) config_sh.PL
+	$(MINIPERL) -I..\lib config_sh.PL $(CFG_VARS) config.w32 > ..\config.sh
+
+# this target is for when changes to the main config.sh happen
+# edit config.{b,v,g}c and make this target once for each supported
+# compiler (e.g. `dmake CCTYPE=BORLAND regen_config_h`)
+regen_config_h:
+	perl config_sh.PL $(CFG_VARS) $(CFGSH_TMPL) > ..\config.sh
+	cd ..
+	-del /f perl.exe
+	perl configpm
+	cd win32
+	-del /f $(CFGH_TMPL)
+	-mkdir $(COREDIR)
+	-perl -I..\lib config_h.PL "INST_VER=$(INST_VER)"
+	rename config.h $(CFGH_TMPL)
+
+$(CONFIGPM) : $(MINIPERL) ..\config.sh config_h.PL ..\minimod.pl
+	cd .. && miniperl configpm
+	if exist lib\* $(RCOPY) lib\*.* ..\lib\$(NULL)
+	$(XCOPY) ..\*.h $(COREDIR)\*.*
+	$(XCOPY) *.h $(COREDIR)\*.*
+	$(XCOPY) ..\ext\re\re.pm $(LIBDIR)\*.*
+	$(RCOPY) include $(COREDIR)\*.*
+	$(MINIPERL) -I..\lib config_h.PL "INST_VER=$(INST_VER)" \
+	    || $(MAKE) /$(MAKEFLAGS) $(CONFIGPM)
+
+$(MINIPERL) : $(MINIDIR) $(MINI_OBJ)
+	$(LINK32) -subsystem:console -out:$@ @<<
+	$(LINK_FLAGS) $(LIBFILES) $(MINI_OBJ)
+<<
+
+$(MINIDIR) :
+	if not exist "$(MINIDIR)" mkdir "$(MINIDIR)"
+
+$(MINICORE_OBJ) : $(CORE_NOCFG_H)
+	$(CC) -c $(CFLAGS) -DPERL_EXTERNAL_GLOB $(OBJOUT_FLAG)$@ ..\$(*F).c
+
+$(MINIWIN32_OBJ) : $(CORE_NOCFG_H)
+	$(CC) -c $(CFLAGS) $(OBJOUT_FLAG)$@ $(*F).c
+
+# -DPERL_IMPLICIT_SYS needs C++ for perllib.c
+# This is the only file that depends on perlhost.h, vmem.h, and vdir.h
+!IF "$(USE_IMP_SYS)$(USE_OBJECT)" == "defineundef"
+perllib$(o)	: perllib.c .\perlhost.h .\vdir.h .\vmem.h
+	$(CC) -c -I. $(CFLAGS_O) $(CXX_FLAG) $(OBJOUT_FLAG)$@ perllib.c
+!ENDIF
+
+# 1. we don't want to rebuild miniperl.exe when config.h changes
+# 2. we don't want to rebuild miniperl.exe with non-default config.h
+$(MINI_OBJ)	: $(CORE_NOCFG_H)
+
+$(WIN32_OBJ)	: $(CORE_H)
+$(CORE_OBJ)	: $(CORE_H)
+$(DLL_OBJ)	: $(CORE_H)
+$(X2P_OBJ)	: $(CORE_H)
+
+perldll.def : $(MINIPERL) $(CONFIGPM) ..\global.sym ..\pp.sym ..\makedef.pl
+	$(MINIPERL) -w ..\makedef.pl PLATFORM=win32 $(OPTIMIZE) $(DEFINES) $(BUILDOPT) \
+	    CCTYPE=$(CCTYPE) > perldll.def
+
+$(PERLDLL): perldll.def $(PERLDLL_OBJ) $(PERLDLL_RES)
+	$(LINK32) -dll -def:perldll.def -base:0x28000000 -out:$@ @<<
+		$(LINK_FLAGS) $(DELAYLOAD) $(LIBFILES) $(PERLDLL_OBJ) $(PERLDLL_RES)
+<<
+	$(XCOPY) $(PERLIMPLIB) $(COREDIR)
+
+$(MINIMOD) : $(MINIPERL) ..\minimod.pl
+	cd .. && miniperl minimod.pl > lib\ExtUtils\Miniperl.pm
+
+..\x2p\a2p$(o) : ..\x2p\a2p.c
+	$(CC) -I..\x2p $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\a2p.c
+
+..\x2p\hash$(o) : ..\x2p\hash.c
+	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\hash.c
+
+..\x2p\str$(o) : ..\x2p\str.c
+	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\str.c
+
+..\x2p\util$(o) : ..\x2p\util.c
+	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\util.c
+
+..\x2p\walk$(o) : ..\x2p\walk.c
+	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\walk.c
+
+$(X2P) : $(MINIPERL) $(X2P_OBJ)
+	$(MINIPERL) ..\x2p\find2perl.PL
+	$(MINIPERL) ..\x2p\s2p.PL
+	$(LINK32) -subsystem:console -out:$@ @<<
+		$(LINK_FLAGS) $(LIBFILES) $(X2P_OBJ)
+<<
+
+perlmain.c : runperl.c 
+	copy runperl.c perlmain.c
+
+perlmain$(o) : perlmain.c
+	$(CC) $(CFLAGS_O) -UPERLDLL $(OBJOUT_FLAG)$@ -c perlmain.c
+
+$(PERLEXE): $(PERLDLL) $(CONFIGPM) $(PERLEXE_OBJ) $(PERLEXE_RES)
+	$(LINK32) -subsystem:console -out:$@ -stack:0x1000000 $(LINK_FLAGS) \
+	    $(LIBFILES) $(PERLEXE_OBJ) $(SETARGV_OBJ) $(PERLIMPLIB) $(PERLEXE_RES)
+	copy $(PERLEXE) $(WPERLEXE)
+	$(MINIPERL) -I..\lib bin\exetype.pl $(WPERLEXE) WINDOWS
+	copy splittree.pl .. 
+	$(MINIPERL) -I..\lib ..\splittree.pl "../LIB" $(AUTODIR)
+
+$(DYNALOADER).c: $(MINIPERL) $(EXTDIR)\DynaLoader\dl_win32.xs $(CONFIGPM)
+	if not exist $(AUTODIR) mkdir $(AUTODIR)
+	cd $(EXTDIR)\$(*B)
+	..\$(MINIPERL) -I..\..\lib $(*B)_pm.PL
+	..\$(MINIPERL) -I..\..\lib XSLoader_pm.PL
+	cd ..\..\win32
+	$(XCOPY) $(EXTDIR)\$(*B)\$(*B).pm $(LIBDIR)\$(NULL)
+	$(XCOPY) $(EXTDIR)\$(*B)\XSLoader.pm $(LIBDIR)\$(NULL)
+	cd $(EXTDIR)\$(*B)
+	$(XSUBPP) dl_win32.xs > $(*B).c
+	cd ..\..\win32
+
+$(EXTDIR)\DynaLoader\dl_win32.xs: dl_win32.xs
+	copy dl_win32.xs $(EXTDIR)\DynaLoader\dl_win32.xs
+
+$(DUMPER_DLL): $(PERLEXE) $(DUMPER).xs
+	cd $(EXTDIR)\Data\$(*B)
+	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\..\win32
+
+$(DPROF_DLL): $(PERLEXE) $(DPROF).xs
+	cd $(EXTDIR)\Devel\$(*B)
+	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\..\win32
+
+$(GLOB_DLL): $(PERLEXE) $(GLOB).xs
+	cd $(EXTDIR)\File\$(*B)
+	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\..\win32
+
+$(PEEK_DLL): $(PERLEXE) $(PEEK).xs
+	cd $(EXTDIR)\Devel\$(*B)
+	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\..\win32
+
+$(RE_DLL): $(PERLEXE) $(RE).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(B_DLL): $(PERLEXE) $(B).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(THREAD_DLL): $(PERLEXE) $(THREAD).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(ATTRS_DLL): $(PERLEXE) $(ATTRS).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(POSIX_DLL): $(PERLEXE) $(POSIX).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(IO_DLL): $(PERLEXE) $(IO).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(SDBM_FILE_DLL) : $(PERLEXE) $(SDBM_FILE).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(FCNTL_DLL): $(PERLEXE) $(FCNTL).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(OPCODE_DLL): $(PERLEXE) $(OPCODE).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(SOCKET_DLL): $(PERLEXE) $(SOCKET).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(HOSTNAME_DLL): $(PERLEXE) $(HOSTNAME).xs
+	cd $(EXTDIR)\Sys\$(*B)
+	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\..\win32
+
+$(BYTELOADER_DLL): $(PERLEXE) $(BYTELOADER).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(STORABLE_DLL): $(PERLEXE) $(STORABLE).xs
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+$(ERRNO_PM): $(PERLEXE) $(ERRNO)_pm.PL
+	cd $(EXTDIR)\$(*B)
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	$(MAKE)
+	cd ..\..\win32
+
+doc: $(PERLEXE)
+	$(PERLEXE) -I..\lib ..\installhtml --podroot=.. --htmldir=./html \
+	    --podpath=pod:lib:ext:utils --htmlroot="file://$(INST_HTML::=|)" \
+	    --libpod=perlfunc:perlguts:perlvar:perlrun:perlop --recurse
+
+utils: $(PERLEXE) $(X2P)
+	cd ..\utils
+	$(MAKE) PERL=$(MINIPERL)
+	cd ..\pod
+	copy ..\README.amiga .\perlamiga.pod
+	copy ..\README.cygwin .\perlcygwin.pod
+	copy ..\README.dos .\perldos.pod
+	copy ..\README.hpux .\perlhpux.pod
+	copy ..\README.machten .\perlmachten.pod
+	copy ..\README.os2 .\perlos2.pod
+	copy ..\vms\perlvms.pod .\perlvms.pod
+	copy ..\README.win32 .\perlwin32.pod
+	$(MAKE) -f ..\win32\pod.mak converters
+	cd ..\lib
+	$(PERLEXE) lib_pm.PL
+	cd ..\win32
+	$(PERLEXE) $(PL2BAT) $(UTILS)
+
+distclean: clean
+	-del /f $(MINIPERL) $(PERLEXE) $(PERLDLL) $(GLOBEXE) \
+		$(PERLIMPLIB) ..\miniperl.lib $(MINIMOD)
+	-del /f *.def *.map
+	-del /f $(EXTENSION_DLL) $(EXTENSION_PM)
+	-del /f $(EXTENSION_C) $(DYNALOADER).c $(ERRNO).pm
+	-del /f $(EXTDIR)\DynaLoader\dl_win32.xs
+	-del /f $(LIBDIR)\.exists $(LIBDIR)\attrs.pm $(LIBDIR)\DynaLoader.pm
+	-del /f $(LIBDIR)\XSLoader.pm
+	-del /f $(LIBDIR)\Fcntl.pm $(LIBDIR)\IO.pm $(LIBDIR)\Opcode.pm
+	-del /f $(LIBDIR)\ops.pm $(LIBDIR)\Safe.pm $(LIBDIR)\Thread.pm
+	-del /f $(LIBDIR)\SDBM_File.pm $(LIBDIR)\Socket.pm $(LIBDIR)\POSIX.pm
+	-del /f $(LIBDIR)\B.pm $(LIBDIR)\O.pm $(LIBDIR)\re.pm
+	-del /f $(LIBDIR)\Data\Dumper.pm $(LIBDIR)\ByteLoader.pm
+	-del /f $(LIBDIR)\Devel\Peek.pm $(LIBDIR)\Devel\DProf.pm
+	-del /f $(LIBDIR)\File\Glob.pm
+	-del /f $(LIBDIR)\Storable.pm
+	-if exist $(LIBDIR)\IO rmdir /s /q $(LIBDIR)\IO || rmdir /s $(LIBDIR)\IO
+	-if exist $(LIBDIR)\Thread rmdir /s /q $(LIBDIR)\Thread || rmdir /s $(LIBDIR)\Thread
+	-if exist $(LIBDIR)\B rmdir /s /q $(LIBDIR)\B || rmdir /s $(LIBDIR)\B
+	-if exist $(LIBDIR)\Data rmdir /s /q $(LIBDIR)\Data || rmdir /s $(LIBDIR)\Data
+	-del /f $(PODDIR)\*.html
+	-del /f $(PODDIR)\*.bat
+	cd ..\utils
+	-del /f h2ph splain perlbug pl2pm c2ph h2xs perldoc dprofpp
+	-del /f *.bat
+	cd ..\win32
+	cd ..\x2p
+	-del /f find2perl s2p
+	-del /f *.bat
+	cd ..\win32
+	-del /f ..\config.sh ..\splittree.pl perlmain.c dlutils.c config.h.new
+	-del /f $(CONFIGPM)
+	-del /f bin\*.bat
+	cd $(EXTDIR)
+	-del /s *.lib *.def *.map *.pdb *.bs Makefile *$(o) pm_to_blib
+	cd ..\win32
+	-if exist $(AUTODIR) rmdir /s /q $(AUTODIR) || rmdir /s $(AUTODIR)
+	-if exist $(COREDIR) rmdir /s /q $(COREDIR) || rmdir /s $(COREDIR)
+
+install : all installbare installhtml
+
+installbare : utils
+	$(PERLEXE) ..\installperl
+	if exist $(WPERLEXE) $(XCOPY) $(WPERLEXE) $(INST_BIN)\*.*
+	$(XCOPY) $(GLOBEXE) $(INST_BIN)\*.*
+	$(XCOPY) bin\*.bat $(INST_SCRIPT)\*.*
+
+installhtml : doc
+	$(RCOPY) html\*.* $(INST_HTML)\*.*
+
+inst_lib : $(CONFIGPM)
+	copy splittree.pl .. 
+	$(MINIPERL) -I..\lib ..\splittree.pl "../LIB" $(AUTODIR)
+	$(RCOPY) ..\lib $(INST_LIB)\*.*
+
+minitest : $(MINIPERL) $(GLOBEXE) $(CONFIGPM) utils
+	$(XCOPY) $(MINIPERL) ..\t\perl.exe
+	$(XCOPY) $(GLOBEXE) ..\t\$(NULL)
+	attrib -r ..\t\*.*
+	copy test ..\t
+	cd ..\t
+	$(MINIPERL) -I..\lib test base/*.t comp/*.t cmd/*.t io/*.t op/*.t pragma/*.t
+	cd ..\win32
+
+test-prep : all utils
+	$(XCOPY) $(PERLEXE) ..\t\$(NULL)
+	$(XCOPY) $(PERLDLL) ..\t\$(NULL)
+	$(XCOPY) $(GLOBEXE) ..\t\$(NULL)
+
+test : test-prep
+	cd ..\t
+	$(PERLEXE) -I..\lib harness
+	cd ..\win32
+
+test-notty : test-prep
+	set PERL_SKIP_TTY_TEST=1
+	cd ..\t
+	$(PERLEXE) -I..\lib harness
+	cd ..\win32
+
+test-wide : test-prep
+	set HARNESS_PERL_SWITCHES=-C
+	cd ..\t
+	$(PERLEXE) -I..\lib harness
+	cd ..\win32
+
+test-wide-notty : test-prep
+	set PERL_SKIP_TTY_TEST=1
+	set HARNESS_PERL_SWITCHES=-C
+	cd ..\t
+	$(PERLEXE) -I..\lib harness
+	cd ..\win32
+
+clean : 
+	-@erase miniperlmain$(o)
+	-@erase $(MINIPERL)
+	-@erase perlglob$(o)
+	-@erase perlmain$(o)
+	-@erase config.w32
+	-@erase /f config.h
+	-@erase $(GLOBEXE)
+	-@erase $(PERLEXE)
+	-@erase $(WPERLEXE)
+	-@erase $(PERLDLL)
+	-@erase $(CORE_OBJ)
+	-if exist $(MINIDIR) rmdir /s /q $(MINIDIR) || rmdir /s $(MINIDIR)
+	-@erase $(WIN32_OBJ)
+	-@erase $(DLL_OBJ)
+	-@erase $(X2P_OBJ)
+	-@erase ..\*$(o) ..\*.lib ..\*.exp *$(o) *.lib *.exp *.res
+	-@erase ..\t\*.exe ..\t\*.dll ..\t\*.bat
+	-@erase ..\x2p\*.exe ..\x2p\*.bat
+	-@erase *.ilk
+	-@erase *.pdb
+ 
+# Handy way to run perlbug -ok without having to install and run the
+# installed perlbug. We don't re-run the tests here - we trust the user.
+# Please *don't* use this unless all tests pass.
+# If you want to report test failures, use "nmake nok" instead.
+ok: utils
+	$(PERLEXE) -I..\lib ..\utils\perlbug -ok -s "(UNINSTALLED)"
+
+okfile: utils
+	$(PERLEXE) -I..\lib ..\utils\perlbug -ok -s "(UNINSTALLED)" -F perl.ok
+ 
+nok: utils
+	$(PERLEXE) -I..\lib ..\utils\perlbug -nok -s "(UNINSTALLED)"
+ 
+nokfile: utils
+	$(PERLEXE) -I..\lib ..\utils\perlbug -nok -s "(UNINSTALLED)" -F perl.nok
diff --git a/win32/makefile.mk b/win32/makefile.mk
index 33deee535b..86a2bf4bfa 100644
--- a/win32/makefile.mk
+++ b/win32/makefile.mk
@@ -1,1329 +1,1329 @@
-#

-# Makefile to build perl on Windows NT using DMAKE.

-# Supported compilers:

-#	Visual C++ 2.0 thro 6.0

-#	Borland C++ 5.02

-#	Mingw32 with gcc-2.95.2 or better  **experimental**

-#

-# This is set up to build a perl.exe that runs off a shared library

-# (perl56.dll).  Also makes individual DLLs for the XS extensions.

-#

-

-##

-## Make sure you read README.win32 *before* you mess with anything here!

-##

-

-##

-## Build configuration.  Edit the values below to suit your needs.

-##

-

-#

-# Set these to wherever you want "dmake install" to put your

-# newly built perl.

-#

-INST_DRV	*= c:

-INST_TOP	*= $(INST_DRV)\perl

-

-#

-# Comment this out if you DON'T want your perl installation to be versioned.

-# This means that the new installation will overwrite any files from the

-# old installation at the same INST_TOP location.  Leaving it enabled is

-# the safest route, as perl adds the extra version directory to all the

-# locations it installs files to.  If you disable it, an alternative

-# versioned installation can be obtained by setting INST_TOP above to a

-# path that includes an arbitrary version string.

-#

-INST_VER	*= \5.6.0

-

-#

-# Comment this out if you DON'T want your perl installation to have

-# architecture specific components.  This means that architecture-

-# specific files will be installed along with the architecture-neutral

-# files.  Leaving it enabled is safer and more flexible, in case you

-# want to build multiple flavors of perl and install them together in

-# the same location.  Commenting it out gives you a simpler

-# installation that is easier to understand for beginners.

-#

-INST_ARCH	*= \$(ARCHNAME)

-

-#

-# uncomment to enable multiple interpreters.  This is need for fork()

-# emulation.

-#

-#USE_MULTI	*= define

-

-#

-# Beginnings of interpreter cloning/threads; still very incomplete.

-# This should be enabled to get the fork() emulation.  This needs

-# USE_MULTI as well.

-#

-#USE_ITHREADS	*= define

-

-#

-# uncomment to enable the implicit "host" layer for all system calls

-# made by perl.  This needs USE_MULTI above.  This is also needed to

-# get fork().

-#

-#USE_IMP_SYS	*= define

-

-#

-# WARNING! This option is deprecated and will eventually go away (enable

-# USE_ITHREADS instead).

-#

-# uncomment to enable threads-capabilities.  This is incompatible with

-# USE_ITHREADS, and is only here for people who may have come to rely

-# on the experimental Thread support that was in 5.005.

-#

-#USE_5005THREADS	*= define

-

-#

-# WARNING! This option is deprecated and will eventually go away (enable

-# USE_MULTI instead).

-#

-# uncomment next line if you want to use the PERL_OBJECT build option.

-# DO NOT ENABLE unless you have legacy code that relies on the C++

-# CPerlObj class that was available in 5.005.  This cannot be enabled

-# if you ask for USE_5005THREADS above.

-#

-#USE_OBJECT	*= define

-

-#

-# uncomment exactly one of the following

-# 

-# Visual C++ 2.x

-#CCTYPE		*= MSVC20

-# Visual C++ > 2.x and < 6.x

-#CCTYPE		*= MSVC

-# Visual C++ >= 6.x

-#CCTYPE		*= MSVC60

-# Borland 5.02 or later

-#CCTYPE		*= BORLAND

-# mingw32+gcc-2.95.2 or better

-CCTYPE		*= GCC

-

-#

-# uncomment this if you are compiling under Windows 95/98 and command.com

-# (not needed if you're running under 4DOS/NT 6.01 or later)

-#IS_WIN95	*= define

-

-#

-# uncomment next line if you want debug version of perl (big,slow)

-# If not enabled, we automatically try to use maximum optimization

-# with all compilers that are known to have a working optimizer.

-#

-#CFG		*= Debug

-

-#

-# uncomment to enable use of PerlCRT.DLL when using the Visual C compiler.

-# It has patches that fix known bugs in older versions of MSVCRT.DLL.

-# This currently requires VC 5.0 with Service Pack 3 or later.

-# Get it from CPAN at http://www.perl.com/CPAN/authors/id/D/DO/DOUGL/

-# and follow the directions in the package to install.

-#

-# Not recommended if you have VC 6.x and you're not running Windows 9x.

-#

-#USE_PERLCRT	*= define

-

-#

-# uncomment to enable linking with setargv.obj under the Visual C

-# compiler. Setting this options enables perl to expand wildcards in

-# arguments, but it may be harder to use alternate methods like

-# File::DosGlob that are more powerful.  This option is supported only with

-# Visual C.

-#

-#USE_SETARGV	*= define

-

-#

-# if you have the source for des_fcrypt(), uncomment this and make sure the

-# file exists (see README.win32).  File should be located in the same

-# directory as this file.

-#

-#CRYPT_SRC	*= fcrypt.c

-

-#

-# if you didn't set CRYPT_SRC and if you have des_fcrypt() available in a

-# library, uncomment this, and make sure the library exists (see README.win32)

-# Specify the full pathname of the library.

-#

-#CRYPT_LIB	*= fcrypt.lib

-

-#

-# set this if you wish to use perl's malloc

-# WARNING: Turning this on/off WILL break binary compatibility with extensions

-# you may have compiled with/without it.  Be prepared to recompile all

-# extensions if you change the default.  Currently, this cannot be enabled

-# if you ask for USE_IMP_SYS above.

-#

-#PERL_MALLOC	*= define

-

-#

-# set the install locations of the compiler include/libraries

-# Running VCVARS32.BAT is *required* when using Visual C.

-# Some versions of Visual C don't define MSVCDIR in the environment,

-# so you may have to set CCHOME explicitly (spaces in the path name should

-# not be quoted)

-#

-#CCHOME		*= c:\bc5

-#CCHOME		*= $(MSVCDIR)

-CCHOME		*= c:\gcc-2.95.2-msvcrt

-CCINCDIR	*= $(CCHOME)\include

-CCLIBDIR	*= $(CCHOME)\lib

-

-#

-# Additional compiler flags can be specified here.

-#

-

-#

-# This should normally be disabled.  Adding -DPERL_POLLUTE enables support

-# for old symbols by default, at the expense of extreme pollution.  You most

-# probably just want to build modules that won't compile with

-#         perl Makefile.PL POLLUTE=1

-# instead of enabling this.  Please report such modules to the respective

-# authors.

-#

-#BUILDOPT	+= -DPERL_POLLUTE

-

-#

-# This should normally be disabled.  Enabling it will disable the File::Glob

-# implementation of CORE::glob.

-#

-#BUILDOPT	+= -DPERL_EXTERNAL_GLOB

-

-#

-# This should normally be disabled.  Enabling it causes perl to read scripts

-# in text mode (which is the 5.005 behavior) and will break ByteLoader.

-#BUILDOPT	+= -DPERL_TEXTMODE_SCRIPTS

-

-#

-# specify semicolon-separated list of extra directories that modules will

-# look for libraries (spaces in path names need not be quoted)

-#

-EXTRALIBDIRS	*=

-

-#

-# set this to point to cmd.exe (only needed if you use some

-# alternate shell that doesn't grok cmd.exe style commands)

-#

-#SHELL		*= g:\winnt\system32\cmd.exe

-

-#

-# set this to your email address (perl will guess a value from

-# from your loginname and your hostname, which may not be right)

-#

-#EMAIL		*=

-

-##

-## Build configuration ends.

-##

-

-##################### CHANGE THESE ONLY IF YOU MUST #####################

-

-.IF "$(CRYPT_SRC)$(CRYPT_LIB)" == ""

-D_CRYPT		= undef

-.ELSE

-D_CRYPT		= define

-CRYPT_FLAG	= -DHAVE_DES_FCRYPT

-.ENDIF

-

-.IF "$(USE_OBJECT)" == "define"

-PERL_MALLOC	!= undef

-USE_5005THREADS	!= undef

-USE_MULTI	!= undef

-USE_IMP_SYS	!= define

-.ENDIF

-

-PERL_MALLOC	*= undef

-

-USE_5005THREADS	*= undef

-

-.IF "$(USE_5005THREADS)" == "define"

-USE_ITHREADS	!= undef

-.ENDIF

-

-.IF "$(USE_IMP_SYS)" == "define"

-PERL_MALLOC	!= undef

-.ENDIF

-

-USE_MULTI	*= undef

-USE_OBJECT	*= undef

-USE_ITHREADS	*= undef

-USE_IMP_SYS	*= undef

-USE_PERLCRT	*= undef

-

-.IF "$(USE_IMP_SYS)$(USE_MULTI)$(USE_5005THREADS)$(USE_OBJECT)" == "defineundefundefundef"

-USE_MULTI	!= define

-.ENDIF

-

-.IF "$(USE_ITHREADS)$(USE_MULTI)$(USE_OBJECT)" == "defineundefundef"

-USE_MULTI	!= define

-USE_5005THREADS	!= undef

-.ENDIF

-

-.IF "$(USE_MULTI)$(USE_5005THREADS)$(USE_OBJECT)" != "undefundefundef"

-BUILDOPT	+= -DPERL_IMPLICIT_CONTEXT

-.ENDIF

-

-.IF "$(USE_IMP_SYS)" != "undef"

-BUILDOPT	+= -DPERL_IMPLICIT_SYS

-.ENDIF

-

-.IMPORT .IGNORE : PROCESSOR_ARCHITECTURE

-

-PROCESSOR_ARCHITECTURE *= x86

-

-.IF "$(USE_OBJECT)" == "define"

-ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-object

-.ELIF "$(USE_5005THREADS)" == "define"

-ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-thread

-.ELIF "$(USE_MULTI)" == "define"

-ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-multi

-.ELSE

-ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)

-.ENDIF

-

-.IF "$(USE_ITHREADS)" == "define"

-ARCHNAME	!:= $(ARCHNAME)-thread

-.ENDIF

-

-# Visual Studio 98 specific

-.IF "$(CCTYPE)" == "MSVC60"

-

-# VC 6.0 can load the socket dll on demand.  Makes the test suite

-# run in about 10% less time.

-DELAYLOAD	*= -DELAYLOAD:wsock32.dll -DELAYLOAD:shell32.dll delayimp.lib 

-

-# VC 6.0 seems capable of compiling perl correctly with optimizations

-# enabled.  Anything earlier fails tests.

-CFG		*= Optimize

-.ENDIF

-

-ARCHDIR		= ..\lib\$(ARCHNAME)

-COREDIR		= ..\lib\CORE

-AUTODIR		= ..\lib\auto

-LIBDIR		= ..\lib

-EXTDIR		= ..\ext

-PODDIR		= ..\pod

-EXTUTILSDIR	= $(LIBDIR)\ExtUtils

-

-#

-INST_SCRIPT	= $(INST_TOP)$(INST_VER)\bin

-INST_BIN	= $(INST_SCRIPT)$(INST_ARCH)

-INST_LIB	= $(INST_TOP)$(INST_VER)\lib

-INST_ARCHLIB	= $(INST_LIB)$(INST_ARCH)

-INST_COREDIR	= $(INST_ARCHLIB)\CORE

-INST_POD	= $(INST_LIB)\pod

-INST_HTML	= $(INST_POD)\html

-

-#

-# Programs to compile, build .lib files and link

-#

-

-.USESHELL :

-

-.IF "$(CCTYPE)" == "BORLAND"

-

-CC		= bcc32

-LINK32		= tlink32

-LIB32		= tlib /P128

-IMPLIB		= implib -c

-RSC		= rc

-

-#

-# Options

-#

-INCLUDES	= -I$(COREDIR) -I.\include -I. -I.. -I"$(CCINCDIR)"

-#PCHFLAGS	= -H -Hc -H=c:\temp\bcmoduls.pch 

-DEFINES		= -DWIN32 $(CRYPT_FLAG)

-LOCDEFS		= -DPERLDLL -DPERL_CORE

-SUBSYS		= console

-CXX_FLAG	= -P

-

-LIBC		= cw32mti.lib

-LIBFILES	= $(CRYPT_LIB) import32.lib $(LIBC) odbc32.lib odbccp32.lib

-

-.IF  "$(CFG)" == "Debug"

-OPTIMIZE	= -v -D_RTLDLL -DDEBUGGING

-LINK_DBG	= -v

-.ELSE

-OPTIMIZE	= -O2 -D_RTLDLL

-LINK_DBG	= 

-.ENDIF

-

-CFLAGS		= -w -g0 -tWM -tWD $(INCLUDES) $(DEFINES) $(LOCDEFS) \

-		$(PCHFLAGS) $(OPTIMIZE)

-LINK_FLAGS	= $(LINK_DBG) -L"$(INST_COREDIR)" -L"$(CCLIBDIR)"

-OBJOUT_FLAG	= -o

-EXEOUT_FLAG	= -e

-LIBOUT_FLAG	= 

-

-.ELIF "$(CCTYPE)" == "GCC"

-

-CC		= gcc

-LINK32		= gcc

-LIB32		= ar rc

-IMPLIB		= dlltool

-RSC		= rc

-

-o = .o

-a = .a

-

-#

-# Options

-#

-

-INCLUDES	= -I$(COREDIR) -I.\include -I. -I..

-DEFINES		= -DWIN32 $(CRYPT_FLAG)

-LOCDEFS		= -DPERLDLL -DPERL_CORE

-SUBSYS		= console

-CXX_FLAG	= -xc++

-

-LIBC		= -lmsvcrt

-

-# same libs as MSVC

-LIBFILES	= $(CRYPT_LIB) $(LIBC) \

-		  -lmoldname -lkernel32 -luser32 -lgdi32 \

-		  -lwinspool -lcomdlg32 -ladvapi32 -lshell32 -lole32 \

-		  -loleaut32 -lnetapi32 -luuid -lwsock32 -lmpr \

-		  -lwinmm -lversion -lodbc32

-

-.IF  "$(CFG)" == "Debug"

-OPTIMIZE	= -g -DDEBUGGING

-LINK_DBG	= -g

-.ELSE

-OPTIMIZE	= -g -O2

-LINK_DBG	= 

-.ENDIF

-

-CFLAGS		= $(INCLUDES) $(DEFINES) $(LOCDEFS) $(OPTIMIZE)

-LINK_FLAGS	= $(LINK_DBG) -L"$(INST_COREDIR)" -L"$(CCLIBDIR)"

-OBJOUT_FLAG	= -o

-EXEOUT_FLAG	= -o

-LIBOUT_FLAG	= 

-

-# NOTE: we assume that GCC uses MSVCRT.DLL

-BUILDOPT	+= -fno-strict-aliasing -DPERL_MSVCRT_READFIX

-

-.ELSE

-

-CC		= cl

-LINK32		= link

-LIB32		= $(LINK32) -lib

-RSC		= rc

-

-#

-# Options

-#

-

-INCLUDES	= -I$(COREDIR) -I.\include -I. -I..

-#PCHFLAGS	= -Fpc:\temp\vcmoduls.pch -YX 

-DEFINES		= -DWIN32 -D_CONSOLE -DNO_STRICT $(CRYPT_FLAG)

-LOCDEFS		= -DPERLDLL -DPERL_CORE

-SUBSYS		= console

-CXX_FLAG	= -TP -GX

-

-.IF "$(USE_PERLCRT)" != "define"

-LIBC	= msvcrt.lib

-.ELSE

-LIBC	= PerlCRT.lib

-.ENDIF

-

-PERLEXE_RES	=

-PERLDLL_RES	=

-

-.IF  "$(CFG)" == "Debug"

-.IF "$(CCTYPE)" == "MSVC20"

-OPTIMIZE	= -Od -MD -Z7 -DDEBUGGING

-.ELSE

-OPTIMIZE	= -Od -MD -Zi -DDEBUGGING

-.ENDIF

-LINK_DBG	= -debug -pdb:none

-.ELSE

-.IF "$(CFG)" == "Optimize"

-# -O1 yields smaller code, which turns out to be faster than -O2

-#OPTIMIZE	= -O2 -MD -DNDEBUG

-OPTIMIZE	= -O1 -MD -DNDEBUG

-.ELSE

-OPTIMIZE	= -Od -MD -DNDEBUG

-.ENDIF

-LINK_DBG	= -release

-.ENDIF

-

-LIBBASEFILES	= $(CRYPT_LIB) \

-		oldnames.lib kernel32.lib user32.lib gdi32.lib winspool.lib \

-		comdlg32.lib advapi32.lib shell32.lib ole32.lib oleaut32.lib \

-		netapi32.lib uuid.lib wsock32.lib mpr.lib winmm.lib \

-		version.lib odbc32.lib odbccp32.lib

-

-# we add LIBC here, since we may be using PerlCRT.dll

-LIBFILES	= $(LIBBASEFILES) $(LIBC)

-

-CFLAGS		= -nologo -Gf -W3 $(INCLUDES) $(DEFINES) $(LOCDEFS) \

-		$(PCHFLAGS) $(OPTIMIZE)

-LINK_FLAGS	= -nologo -nodefaultlib $(LINK_DBG) \

-		-libpath:"$(INST_COREDIR)" \

-		-machine:$(PROCESSOR_ARCHITECTURE)

-OBJOUT_FLAG	= -Fo

-EXEOUT_FLAG	= -Fe

-LIBOUT_FLAG	= /out:

-

-.IF "$(USE_PERLCRT)" != "define"

-BUILDOPT	+= -DPERL_MSVCRT_READFIX

-.ENDIF

-

-.ENDIF

-

-.IF "$(USE_OBJECT)" == "define"

-OPTIMIZE	+= $(CXX_FLAG)

-BUILDOPT	+= -DPERL_OBJECT

-.ENDIF

-

-CFLAGS_O	= $(CFLAGS) $(BUILDOPT)

-

-# used to allow local linking flags that are not propogated into Config.pm,

-# currently unused

-#   -- BKS, 12-12-1999

-PRIV_LINK_FLAGS	*=

-BLINK_FLAGS	= $(PRIV_LINK_FLAGS) $(LINK_FLAGS)

-

-#################### do not edit below this line #######################

-############# NO USER-SERVICEABLE PARTS BEYOND THIS POINT ##############

-

-o *= .obj

-a *= .lib

-

-LKPRE		= INPUT (

-LKPOST		= )

-

-#

-# Rules

-# 

-

-.SUFFIXES : .c $(o) .dll $(a) .exe .rc .res

-

-.c$(o):

-	$(CC) -c $(null,$(<:d) $(NULL) -I$(<:d)) $(CFLAGS_O) $(OBJOUT_FLAG)$@ $<

-

-.y.c:

-	$(NOOP)

-

-$(o).dll:

-.IF "$(CCTYPE)" == "BORLAND"

-	$(LINK32) -Tpd -ap $(BLINK_FLAGS) c0d32$(o) $<,$@,,$(LIBFILES),$(*B).def

-	$(IMPLIB) $(*B).lib $@

-.ELIF "$(CCTYPE)" == "GCC"

-	$(LINK32) -o $@ $(BLINK_FLAGS) $< $(LIBFILES)

-	$(IMPLIB) --input-def $(*B).def --output-lib $(*B).a $@

-.ELSE

-	$(LINK32) -dll -subsystem:windows -implib:$(*B).lib -def:$(*B).def \

-	    -out:$@ $(BLINK_FLAGS) $(LIBFILES) $< $(LIBPERL)  

-.ENDIF

-

-.rc.res:

-	$(RSC) -i.. $<

-

-#

-# various targets

-MINIPERL	= ..\miniperl.exe

-MINIDIR		= .\mini

-PERLEXE		= ..\perl.exe

-WPERLEXE	= ..\wperl.exe

-GLOBEXE		= ..\perlglob.exe

-CONFIGPM	= ..\lib\Config.pm

-MINIMOD		= ..\lib\ExtUtils\Miniperl.pm

-X2P		= ..\x2p\a2p.exe

-

-PL2BAT		= bin\pl2bat.pl

-GLOBBAT		= bin\perlglob.bat

-

-UTILS		=			\

-		..\utils\h2ph		\

-		..\utils\splain		\

-		..\utils\dprofpp	\

-		..\utils\perlbug	\

-		..\utils\pl2pm 		\

-		..\utils\c2ph		\

-		..\utils\h2xs		\

-		..\utils\perldoc	\

-		..\utils\perlcc		\

-		..\pod\checkpods	\

-		..\pod\pod2html		\

-		..\pod\pod2latex	\

-		..\pod\pod2man		\

-		..\pod\pod2text		\

-		..\pod\pod2usage	\

-		..\pod\podchecker	\

-		..\pod\podselect	\

-		..\x2p\find2perl	\

-		..\x2p\s2p		\

-		bin\exetype.pl		\

-		bin\runperl.pl		\

-		bin\pl2bat.pl		\

-		bin\perlglob.pl		\

-		bin\search.pl

-

-.IF "$(CCTYPE)" == "BORLAND"

-

-CFGSH_TMPL	= config.bc

-CFGH_TMPL	= config_H.bc

-

-.ELIF "$(CCTYPE)" == "GCC"

-

-CFGSH_TMPL	= config.gc

-CFGH_TMPL	= config_H.gc

-PERLIMPLIB	= ..\libperl56$(a)

-

-.ELSE

-

-CFGSH_TMPL	= config.vc

-CFGH_TMPL	= config_H.vc

-

-.ENDIF

-

-PERLIMPLIB	*= ..\perl56$(a)

-PERLDLL		= ..\perl56.dll

-

-XCOPY		= xcopy /f /r /i /d

-RCOPY		= xcopy /f /r /i /e /d

-NOOP		= @echo

-

-#

-# filenames given to xsubpp must have forward slashes (since it puts

-# full pathnames in #line strings)

-XSUBPP		= ..\$(MINIPERL) -I..\..\lib ..\$(EXTUTILSDIR)\xsubpp \

-		-C++ -prototypes

-

-MICROCORE_SRC	=		\

-		..\av.c		\

-		..\deb.c	\

-		..\doio.c	\

-		..\doop.c	\

-		..\dump.c	\

-		..\globals.c	\

-		..\gv.c		\

-		..\hv.c		\

-		..\mg.c		\

-		..\op.c		\

-		..\perl.c	\

-		..\perlapi.c	\

-		..\perly.c	\

-		..\pp.c		\

-		..\pp_ctl.c	\

-		..\pp_hot.c	\

-		..\pp_sys.c	\

-		..\regcomp.c	\

-		..\regexec.c	\

-		..\run.c	\

-		..\scope.c	\

-		..\sv.c		\

-		..\taint.c	\

-		..\toke.c	\

-		..\universal.c	\

-		..\utf8.c	\

-		..\util.c	\

-		..\xsutils.c

-

-EXTRACORE_SRC	+= perllib.c

-

-.IF "$(PERL_MALLOC)" == "define"

-EXTRACORE_SRC	+= ..\malloc.c

-.ENDIF

-

-.IF "$(USE_OBJECT)" != "define"

-EXTRACORE_SRC	+= ..\perlio.c

-.ENDIF

-

-WIN32_SRC	=		\

-		.\win32.c	\

-		.\win32sck.c	\

-		.\win32thread.c 

-

-.IF "$(CRYPT_SRC)" != ""

-WIN32_SRC	+= .\$(CRYPT_SRC)

-.ENDIF

-

-DLL_SRC		= $(DYNALOADER).c

-

-X2P_SRC		=		\

-		..\x2p\a2p.c	\

-		..\x2p\hash.c	\

-		..\x2p\str.c	\

-		..\x2p\util.c	\

-		..\x2p\walk.c

-

-CORE_NOCFG_H	=		\

-		..\av.h		\

-		..\cop.h	\

-		..\cv.h		\

-		..\dosish.h	\

-		..\embed.h	\

-		..\form.h	\

-		..\gv.h		\

-		..\handy.h	\

-		..\hv.h		\

-		..\iperlsys.h	\

-		..\mg.h		\

-		..\nostdio.h	\

-		..\op.h		\

-		..\opcode.h	\

-		..\perl.h	\

-		..\perlapi.h	\

-		..\perlsdio.h	\

-		..\perlsfio.h	\

-		..\perly.h	\

-		..\pp.h		\

-		..\proto.h	\

-		..\regexp.h	\

-		..\scope.h	\

-		..\sv.h		\

-		..\thread.h	\

-		..\unixish.h	\

-		..\utf8.h	\

-		..\util.h	\

-		..\warnings.h	\

-		..\XSUB.h	\

-		..\EXTERN.h	\

-		..\perlvars.h	\

-		..\intrpvar.h	\

-		..\thrdvar.h	\

-		.\include\dirent.h	\

-		.\include\netdb.h	\

-		.\include\sys\socket.h	\

-		.\win32.h

-

-CORE_H		= $(CORE_NOCFG_H) .\config.h

-

-MICROCORE_OBJ	= $(MICROCORE_SRC:db:+$(o))

-CORE_OBJ	= $(MICROCORE_OBJ) $(EXTRACORE_SRC:db:+$(o))

-WIN32_OBJ	= $(WIN32_SRC:db:+$(o))

-MINICORE_OBJ	= $(MINIDIR)\{$(MICROCORE_OBJ:f) miniperlmain$(o) perlio$(o)}

-MINIWIN32_OBJ	= $(MINIDIR)\{$(WIN32_OBJ:f)}

-MINI_OBJ	= $(MINICORE_OBJ) $(MINIWIN32_OBJ)

-DLL_OBJ		= $(DLL_SRC:db:+$(o))

-X2P_OBJ		= $(X2P_SRC:db:+$(o))

-

-PERLDLL_OBJ	= $(CORE_OBJ)

-PERLEXE_OBJ	= perlmain$(o)

-

-PERLDLL_OBJ	+= $(WIN32_OBJ) $(DLL_OBJ)

-

-.IF "$(USE_SETARGV)" != ""

-SETARGV_OBJ	= setargv$(o)

-.ENDIF

-

-DYNAMIC_EXT	= Socket IO Fcntl Opcode SDBM_File POSIX attrs Thread B re \

-		Data/Dumper Devel/Peek ByteLoader Devel/DProf File/Glob \

-		Sys/Hostname Storable

-STATIC_EXT	= DynaLoader

-NONXS_EXT	= Errno

-

-DYNALOADER	= $(EXTDIR)\DynaLoader\DynaLoader

-SOCKET		= $(EXTDIR)\Socket\Socket

-FCNTL		= $(EXTDIR)\Fcntl\Fcntl

-OPCODE		= $(EXTDIR)\Opcode\Opcode

-SDBM_FILE	= $(EXTDIR)\SDBM_File\SDBM_File

-IO		= $(EXTDIR)\IO\IO

-POSIX		= $(EXTDIR)\POSIX\POSIX

-ATTRS		= $(EXTDIR)\attrs\attrs

-THREAD		= $(EXTDIR)\Thread\Thread

-B		= $(EXTDIR)\B\B

-RE		= $(EXTDIR)\re\re

-DUMPER		= $(EXTDIR)\Data\Dumper\Dumper

-ERRNO		= $(EXTDIR)\Errno\Errno

-PEEK		= $(EXTDIR)\Devel\Peek\Peek

-BYTELOADER	= $(EXTDIR)\ByteLoader\ByteLoader

-DPROF		= $(EXTDIR)\Devel\DProf\DProf

-GLOB		= $(EXTDIR)\File\Glob\Glob

-HOSTNAME	= $(EXTDIR)\Sys\Hostname\Hostname

-STORABLE	= $(EXTDIR)\Storable\Storable

-

-SOCKET_DLL	= $(AUTODIR)\Socket\Socket.dll

-FCNTL_DLL	= $(AUTODIR)\Fcntl\Fcntl.dll

-OPCODE_DLL	= $(AUTODIR)\Opcode\Opcode.dll

-SDBM_FILE_DLL	= $(AUTODIR)\SDBM_File\SDBM_File.dll

-IO_DLL		= $(AUTODIR)\IO\IO.dll

-POSIX_DLL	= $(AUTODIR)\POSIX\POSIX.dll

-ATTRS_DLL	= $(AUTODIR)\attrs\attrs.dll

-THREAD_DLL	= $(AUTODIR)\Thread\Thread.dll

-B_DLL		= $(AUTODIR)\B\B.dll

-DUMPER_DLL	= $(AUTODIR)\Data\Dumper\Dumper.dll

-PEEK_DLL	= $(AUTODIR)\Devel\Peek\Peek.dll

-RE_DLL		= $(AUTODIR)\re\re.dll

-BYTELOADER_DLL	= $(AUTODIR)\ByteLoader\ByteLoader.dll

-DPROF_DLL	= $(AUTODIR)\Devel\DProf\DProf.dll

-GLOB_DLL	= $(AUTODIR)\File\Glob\Glob.dll

-HOSTNAME_DLL	= $(AUTODIR)\Sys\Hostname\Hostname.dll

-STORABLE_DLL	= $(AUTODIR)\Storable\Storable.dll

-

-ERRNO_PM	= $(LIBDIR)\Errno.pm

-

-EXTENSION_C	=		\

-		$(SOCKET).c	\

-		$(FCNTL).c	\

-		$(OPCODE).c	\

-		$(SDBM_FILE).c	\

-		$(IO).c		\

-		$(POSIX).c	\

-		$(ATTRS).c	\

-		$(THREAD).c	\

-		$(RE).c		\

-		$(DUMPER).c	\

-		$(PEEK).c	\

-		$(B).c		\

-		$(BYTELOADER).c	\

-		$(DPROF).c	\

-		$(GLOB).c	\

-		$(HOSTNAME).c	\

-		$(STORABLE).c

-

-EXTENSION_DLL	=		\

-		$(SOCKET_DLL)	\

-		$(FCNTL_DLL)	\

-		$(OPCODE_DLL)	\

-		$(SDBM_FILE_DLL)\

-		$(IO_DLL)	\

-		$(POSIX_DLL)	\

-		$(ATTRS_DLL)	\

-		$(DUMPER_DLL)	\

-		$(PEEK_DLL)	\

-		$(B_DLL)	\

-		$(RE_DLL)	\

-		$(THREAD_DLL)	\

-		$(BYTELOADER_DLL)	\

-		$(DPROF_DLL)	\

-		$(GLOB_DLL)	\

-		$(HOSTNAME_DLL)	\

-		$(STORABLE_DLL)

-

-EXTENSION_PM	=		\

-		$(ERRNO_PM)

-

-POD2HTML	= $(PODDIR)\pod2html

-POD2MAN		= $(PODDIR)\pod2man

-POD2LATEX	= $(PODDIR)\pod2latex

-POD2TEXT	= $(PODDIR)\pod2text

-

-# vars must be separated by "\t+~\t+", since we're using the tempfile

-# version of config_sh.pl (we were overflowing someone's buffer by

-# trying to fit them all on the command line)

-#	-- BKS 10-17-1999

-CFG_VARS	=					\

-		INST_DRV=$(INST_DRV)		~	\

-		INST_TOP=$(INST_TOP:s/\/\\/)	~	\

-		INST_VER=$(INST_VER:s/\/\\/)	~	\

-		INST_ARCH=$(INST_ARCH)		~	\

-		archname=$(ARCHNAME)		~	\

-		cc=$(CC)			~	\

-		ccflags=$(OPTIMIZE) $(DEFINES) $(BUILDOPT)	~	\

-		cf_email=$(EMAIL)		~	\

-		d_crypt=$(D_CRYPT)		~	\

-		d_mymalloc=$(PERL_MALLOC)	~	\

-		libs=$(LIBFILES:f)		~	\

-		incpath=$(CCINCDIR:s/\/\\/)	~	\

-		libperl=$(PERLIMPLIB:f)		~	\

-		libpth=$(CCLIBDIR:s/\/\\/);$(EXTRALIBDIRS:s/\/\\/)	~	\

-		libc=$(LIBC)			~	\

-		make=dmake			~	\

-		_o=$(o)	obj_ext=$(o)		~	\

-		_a=$(a)	lib_ext=$(a)		~	\

-		static_ext=$(STATIC_EXT)	~	\

-		dynamic_ext=$(DYNAMIC_EXT)	~	\

-		nonxs_ext=$(NONXS_EXT)		~	\

-		use5005threads=$(USE_5005THREADS)	~	\

-		useithreads=$(USE_ITHREADS)	~	\

-		usethreads=$(USE_5005THREADS)	~	\

-		usemultiplicity=$(USE_MULTI)	~	\

-		LINK_FLAGS=$(LINK_FLAGS:s/\/\\/)		~	\

-		optimize=$(OPTIMIZE)

-

-#

-# set up targets varying between Win95 and WinNT builds

-#

-

-.IF "$(IS_WIN95)" == "define"

-MK2 		= .\makefile.95

-RIGHTMAKE	= __switch_makefiles

-NOOP		= @rem

-.ELSE

-MK2		= __not_needed

-RIGHTMAKE	= __not_needed

-.ENDIF

-

-#

-# Top targets

-#

-

-all : .\config.h $(GLOBEXE) $(MINIPERL) $(MK2)		\

-	$(RIGHTMAKE) $(MINIMOD) $(CONFIGPM) $(PERLEXE)	\

-	$(X2P) $(EXTENSION_DLL) $(EXTENSION_PM)

-

-$(DYNALOADER)$(o) : $(DYNALOADER).c $(CORE_H) $(EXTDIR)\DynaLoader\dlutils.c

-

-#----------------------------------------------------------------

-

-#-------------------- BEGIN Win95 SPECIFIC ----------------------

-

-# this target is a jump-off point for Win95

-#  1. it switches to the Win95-specific makefile if it exists

-#     (__do_switch_makefiles)

-#  2. it prints a message when the Win95-specific one finishes (__done)

-#  3. it then kills this makefile by trying to make __no_such_target

-

-__switch_makefiles: __do_switch_makefiles __done __no_such_target

-

-__do_switch_makefiles:

-.IF "$(NOTFIRST)" != "true"

-	if exist $(MK2) $(MAKE:s/-S//) -f $(MK2) $(MAKETARGETS) NOTFIRST=true

-.ELSE

-	$(NOOP)

-.ENDIF

-

-.IF "$(NOTFIRST)" != "true"

-__done:

-	@echo Build process complete. Ignore any errors after this message.

-	@echo Run "dmake test" to test and "dmake install" to install

-

-.ELSE

-# dummy targets for Win95-specific makefile

-

-__done:

-	$(NOOP)

-

-__no_such_target:

-	$(NOOP)

-

-.ENDIF

-

-# This target is used to generate the new makefile (.\makefile.95) for Win95

-

-.\makefile.95: .\makefile.mk

-	$(MINIPERL) genmk95.pl makefile.mk $(MK2)

-

-#--------------------- END Win95 SPECIFIC ---------------------

-

-# a blank target for when builds don't need to do certain things

-# this target added for Win95 port but used to keep the WinNT port able to 

-# use this file

-__not_needed:

-	$(NOOP)

-

-$(GLOBEXE) : perlglob$(o)

-.IF "$(CCTYPE)" == "BORLAND"

-	$(CC) -c -w -v -tWM -I"$(CCINCDIR)" perlglob.c

-	$(LINK32) -Tpe -ap $(BLINK_FLAGS) c0x32$(o) perlglob$(o) \

-	    "$(CCLIBDIR)\32BIT\wildargs$(o)",$@,,import32.lib cw32mt.lib,

-.ELIF "$(CCTYPE)" == "GCC"

-	$(LINK32) $(BLINK_FLAGS) -mconsole -o $@ perlglob$(o) $(LIBFILES)

-.ELSE

-	$(LINK32) $(BLINK_FLAGS) $(LIBFILES) -out:$@ -subsystem:$(SUBSYS) \

-	    perlglob$(o) setargv$(o) 

-.ENDIF

-

-perlglob$(o)  : perlglob.c

-

-config.w32 : $(CFGSH_TMPL)

-	copy $(CFGSH_TMPL) config.w32

-

-.\config.h : $(CFGH_TMPL) $(CORE_NOCFG_H)

-	-del /f config.h

-	copy $(CFGH_TMPL) config.h

-

-..\config.sh : config.w32 $(MINIPERL) config_sh.PL

-	$(MINIPERL) -I..\lib config_sh.PL --cfgsh-option-file \

-	    $(mktmp $(CFG_VARS)) config.w32 > ..\config.sh

-

-# this target is for when changes to the main config.sh happen

-# edit config.{b,v,g}c and make this target once for each supported

-# compiler (e.g. `dmake CCTYPE=BORLAND regen_config_h`)

-regen_config_h:

-	perl config_sh.PL --cfgsh-option-file $(mktmp $(CFG_VARS)) \

-	    $(CFGSH_TMPL) > ..\config.sh

-	-cd .. && del /f perl.exe

-	cd .. && perl configpm

-	-del /f $(CFGH_TMPL)

-	-mkdir $(COREDIR)

-	-perl -I..\lib config_h.PL "INST_VER=$(INST_VER)"

-	rename config.h $(CFGH_TMPL)

-

-$(CONFIGPM) : $(MINIPERL) ..\config.sh config_h.PL ..\minimod.pl

-	cd .. && miniperl configpm

-	if exist lib\* $(RCOPY) lib\*.* ..\lib\$(NULL)

-	$(XCOPY) ..\*.h $(COREDIR)\*.*

-	$(XCOPY) *.h $(COREDIR)\*.*

-	$(XCOPY) ..\ext\re\re.pm $(LIBDIR)\*.*

-	$(RCOPY) include $(COREDIR)\*.*

-	$(MINIPERL) -I..\lib config_h.PL "INST_VER=$(INST_VER)" \

-	    || $(MAKE) $(MAKEMACROS) $(CONFIGPM) $(MAKEFILE)

-

-$(MINIPERL) : $(MINIDIR) $(MINI_OBJ) $(CRTIPMLIBS)

-.IF "$(CCTYPE)" == "BORLAND"

-	$(LINK32) -Tpe -ap $(BLINK_FLAGS) \

-	    @$(mktmp c0x32$(o) $(MINI_OBJ:s,\,\\),$(@:s,\,\\),,$(LIBFILES),)

-.ELIF "$(CCTYPE)" == "GCC"

-	$(LINK32) -v -mconsole -o $@ $(BLINK_FLAGS) \

-	    $(mktmp $(LKPRE) $(MINI_OBJ:s,\,\\) $(LIBFILES) $(LKPOST)) 

-.ELSE

-	$(LINK32) -subsystem:console -out:$@ \

-	    @$(mktmp $(BLINK_FLAGS) $(LIBFILES) $(MINI_OBJ:s,\,\\))

-.ENDIF

-

-$(MINIDIR) :

-	if not exist "$(MINIDIR)" mkdir "$(MINIDIR)"

-

-$(MINICORE_OBJ) : $(CORE_NOCFG_H)

-	$(CC) -c $(CFLAGS) -DPERL_EXTERNAL_GLOB $(OBJOUT_FLAG)$@ ..\$(*B).c

-

-$(MINIWIN32_OBJ) : $(CORE_NOCFG_H)

-	$(CC) -c $(CFLAGS) $(OBJOUT_FLAG)$@ $(*B).c

-

-# -DPERL_IMPLICIT_SYS needs C++ for perllib.c

-# rules wrapped in .IFs break Win9X build (we end up with unbalanced []s unless

-# unless the .IF is true), so instead we use a .ELSE with the default.

-# This is the only file that depends on perlhost.h, vmem.h, and vdir.h

-

-perllib$(o)	: perllib.c .\perlhost.h .\vdir.h .\vmem.h

-.IF "$(USE_IMP_SYS)$(USE_OBJECT)" == "defineundef"

-	$(CC) -c -I. $(CFLAGS_O) $(CXX_FLAG) $(OBJOUT_FLAG)$@ perllib.c

-.ELSE

-	$(CC) -c -I. $(CFLAGS_O) $(OBJOUT_FLAG)$@ perllib.c

-.ENDIF

-

-# 1. we don't want to rebuild miniperl.exe when config.h changes

-# 2. we don't want to rebuild miniperl.exe with non-default config.h

-$(MINI_OBJ)	: $(CORE_NOCFG_H)

-

-$(WIN32_OBJ)	: $(CORE_H)

-$(CORE_OBJ)	: $(CORE_H)

-$(DLL_OBJ)	: $(CORE_H)

-$(X2P_OBJ)	: $(CORE_H)

-

-perldll.def : $(MINIPERL) $(CONFIGPM) ..\global.sym ..\pp.sym ..\makedef.pl

-	$(MINIPERL) -w ..\makedef.pl PLATFORM=win32 $(OPTIMIZE) $(DEFINES) \

-	$(BUILDOPT) CCTYPE=$(CCTYPE) > perldll.def

-

-$(PERLDLL): perldll.def $(PERLDLL_OBJ) $(PERLDLL_RES)

-.IF "$(CCTYPE)" == "BORLAND"

-	$(LINK32) -Tpd -ap $(BLINK_FLAGS) \

-	    @$(mktmp c0d32$(o) $(PERLDLL_OBJ:s,\,\\)\n \

-		$@,\n \

-		$(LIBFILES)\n \

-		perldll.def\n)

-	$(IMPLIB) $*.lib $@

-.ELIF "$(CCTYPE)" == "GCC"

-	$(LINK32) -mdll -o $@ -Wl,--base-file -Wl,perl.base $(BLINK_FLAGS) \

-	    $(mktmp $(LKPRE) $(PERLDLL_OBJ:s,\,\\) $(LIBFILES) $(LKPOST))

-	dlltool --output-lib $(PERLIMPLIB) \

-		--dllname $(PERLDLL:b).dll \

-		--def perldll.def \

-		--base-file perl.base \

-		--output-exp perl.exp

-	$(LINK32) -mdll -o $@ $(BLINK_FLAGS) \

-	    $(mktmp $(LKPRE) $(PERLDLL_OBJ:s,\,\\) $(LIBFILES) \

-		perl.exp $(LKPOST))

-.ELSE

-	$(LINK32) -dll -def:perldll.def -out:$@ \

-	    @$(mktmp -base:0x28000000 $(BLINK_FLAGS) $(DELAYLOAD) $(LIBFILES) \

-	        $(PERLDLL_RES) $(PERLDLL_OBJ:s,\,\\))

-.ENDIF

-	$(XCOPY) $(PERLIMPLIB) $(COREDIR)

-

-$(MINIMOD) : $(MINIPERL) ..\minimod.pl

-	cd .. && miniperl minimod.pl > lib\ExtUtils\Miniperl.pm

-

-..\x2p\a2p$(o) : ..\x2p\a2p.c

-	$(CC) -I..\x2p $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\a2p.c

-

-..\x2p\hash$(o) : ..\x2p\hash.c

-	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\hash.c

-

-..\x2p\str$(o) : ..\x2p\str.c

-	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\str.c

-

-..\x2p\util$(o) : ..\x2p\util.c

-	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\util.c

-

-..\x2p\walk$(o) : ..\x2p\walk.c

-	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\walk.c

-

-$(X2P) : $(MINIPERL) $(X2P_OBJ)

-	$(MINIPERL) ..\x2p\find2perl.PL

-	$(MINIPERL) ..\x2p\s2p.PL

-.IF "$(CCTYPE)" == "BORLAND"

-	$(LINK32) -Tpe -ap $(BLINK_FLAGS) \

-	    @$(mktmp c0x32$(o) $(X2P_OBJ:s,\,\\),$(@:s,\,\\),,$(LIBFILES),)

-.ELIF "$(CCTYPE)" == "GCC"

-	$(LINK32) -v -o $@ $(BLINK_FLAGS) \

-	    $(mktmp $(LKPRE) $(X2P_OBJ:s,\,\\) $(LIBFILES) $(LKPOST))

-.ELSE

-	$(LINK32) -subsystem:console -out:$@ \

-	    @$(mktmp $(BLINK_FLAGS) $(LIBFILES) $(X2P_OBJ:s,\,\\))

-.ENDIF

-

-perlmain.c : runperl.c 

-	copy runperl.c perlmain.c

-

-perlmain$(o) : perlmain.c

-	$(CC) $(CFLAGS_O) -UPERLDLL $(OBJOUT_FLAG)$@ -c perlmain.c

-

-$(PERLEXE): $(PERLDLL) $(CONFIGPM) $(PERLEXE_OBJ) $(PERLEXE_RES)

-.IF "$(CCTYPE)" == "BORLAND"

-	$(LINK32) -Tpe -ap $(BLINK_FLAGS) \

-	    @$(mktmp c0x32$(o) $(PERLEXE_OBJ:s,\,\\)\n \

-	    $(@:s,\,\\),\n \

-	    $(PERLIMPLIB) $(LIBFILES)\n)

-.ELIF "$(CCTYPE)" == "GCC"

-	$(LINK32) -mconsole -o $@ $(BLINK_FLAGS)  \

-	    $(PERLEXE_OBJ) $(PERLIMPLIB) $(LIBFILES)

-.ELSE

-	$(LINK32) -subsystem:console -out:$@ -stack:0x1000000 $(BLINK_FLAGS) \

-	    $(LIBFILES) $(PERLEXE_OBJ) $(SETARGV_OBJ) $(PERLIMPLIB) $(PERLEXE_RES)

-.ENDIF

-	copy $(PERLEXE) $(WPERLEXE)

-	$(MINIPERL) -I..\lib bin\exetype.pl $(WPERLEXE) WINDOWS

-	copy splittree.pl .. 

-	$(MINIPERL) -I..\lib ..\splittree.pl "../LIB" $(AUTODIR)

-

-$(DYNALOADER).c: $(MINIPERL) $(EXTDIR)\DynaLoader\dl_win32.xs $(CONFIGPM)

-	if not exist $(AUTODIR) mkdir $(AUTODIR)

-	cd $(EXTDIR)\$(*B) && ..\$(MINIPERL) -I..\..\lib $(*B)_pm.PL

-	cd $(EXTDIR)\$(*B) && ..\$(MINIPERL) -I..\..\lib XSLoader_pm.PL

-	$(XCOPY) $(EXTDIR)\$(*B)\$(*B).pm $(LIBDIR)\$(NULL)

-	$(XCOPY) $(EXTDIR)\$(*B)\XSLoader.pm $(LIBDIR)\$(NULL)

-	cd $(EXTDIR)\$(*B) && $(XSUBPP) dl_win32.xs > $(*B).c

-	$(XCOPY) $(EXTDIR)\$(*B)\dlutils.c .

-

-$(EXTDIR)\DynaLoader\dl_win32.xs: dl_win32.xs

-	copy dl_win32.xs $(EXTDIR)\DynaLoader\dl_win32.xs

-

-$(DUMPER_DLL): $(PERLEXE) $(DUMPER).xs

-	cd $(EXTDIR)\Data\$(*B) && \

-	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\Data\$(*B) && $(MAKE)

-

-$(DPROF_DLL): $(PERLEXE) $(DPROF).xs

-	cd $(EXTDIR)\Devel\$(*B) && \

-	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\Devel\$(*B) && $(MAKE)

-

-$(GLOB_DLL): $(PERLEXE) $(GLOB).xs

-	cd $(EXTDIR)\File\$(*B) && \

-	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\File\$(*B) && $(MAKE)

-

-$(PEEK_DLL): $(PERLEXE) $(PEEK).xs

-	cd $(EXTDIR)\Devel\$(*B) && \

-	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\Devel\$(*B) && $(MAKE)

-

-$(RE_DLL): $(PERLEXE) $(RE).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(B_DLL): $(PERLEXE) $(B).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(THREAD_DLL): $(PERLEXE) $(THREAD).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(ATTRS_DLL): $(PERLEXE) $(ATTRS).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(POSIX_DLL): $(PERLEXE) $(POSIX).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(IO_DLL): $(PERLEXE) $(IO).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(SDBM_FILE_DLL) : $(PERLEXE) $(SDBM_FILE).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(FCNTL_DLL): $(PERLEXE) $(FCNTL).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(OPCODE_DLL): $(PERLEXE) $(OPCODE).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(SOCKET_DLL): $(PERLEXE) $(SOCKET).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(HOSTNAME_DLL): $(PERLEXE) $(HOSTNAME).xs

-	cd $(EXTDIR)\Sys\$(*B) && \

-	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\Sys\$(*B) && $(MAKE)

-

-$(BYTELOADER_DLL): $(PERLEXE) $(BYTELOADER).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(STORABLE_DLL): $(PERLEXE) $(STORABLE).xs

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-$(ERRNO_PM): $(PERLEXE) $(ERRNO)_pm.PL

-	cd $(EXTDIR)\$(*B) && \

-	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl

-	cd $(EXTDIR)\$(*B) && $(MAKE)

-

-doc: $(PERLEXE)

-	$(PERLEXE) -I..\lib ..\installhtml --podroot=.. --htmldir=./html \

-	    --podpath=pod:lib:ext:utils --htmlroot="file://$(INST_HTML:s,:,|,)"\

-	    --libpod=perlfunc:perlguts:perlvar:perlrun:perlop --recurse

-

-utils: $(PERLEXE) $(X2P)

-	cd ..\utils && $(MAKE) PERL=$(MINIPERL)

-	copy ..\README.amiga ..\pod\perlamiga.pod

-	copy ..\README.cygwin ..\pod\perlcygwin.pod

-	copy ..\README.dos ..\pod\perldos.pod

-	copy ..\README.hpux ..\pod\perlhpux.pod

-	copy ..\README.machten ..\pod\perlmachten.pod

-	copy ..\README.os2 ..\pod\perlos2.pod

-	copy ..\README.os2 ..\pod\perlos2.pod

-	copy ..\vms\perlvms.pod ..\pod\perlvms.pod

-	cd ..\pod && $(MAKE) -f ..\win32\pod.mak converters

-	cd ..\lib && $(PERLEXE) lib_pm.PL

-	$(PERLEXE) $(PL2BAT) $(UTILS)

-

-distclean: clean

-	-del /f $(MINIPERL) $(PERLEXE) $(PERLDLL) $(GLOBEXE) \

-		$(PERLIMPLIB) ..\miniperl$(a) $(MINIMOD)

-	-del /f *.def *.map

-	-del /f $(EXTENSION_DLL) $(EXTENSION_PM)

-	-del /f $(EXTENSION_C) $(DYNALOADER).c $(ERRNO).pm

-	-del /f $(EXTDIR)\DynaLoader\dl_win32.xs

-	-del /f $(LIBDIR)\.exists $(LIBDIR)\attrs.pm $(LIBDIR)\DynaLoader.pm

-	-del /f $(LIBDIR)\XSLoader.pm

-	-del /f $(LIBDIR)\Fcntl.pm $(LIBDIR)\IO.pm $(LIBDIR)\Opcode.pm

-	-del /f $(LIBDIR)\ops.pm $(LIBDIR)\Safe.pm $(LIBDIR)\Thread.pm

-	-del /f $(LIBDIR)\SDBM_File.pm $(LIBDIR)\Socket.pm $(LIBDIR)\POSIX.pm

-	-del /f $(LIBDIR)\B.pm $(LIBDIR)\O.pm $(LIBDIR)\re.pm

-	-del /f $(LIBDIR)\Data\Dumper.pm $(LIBDIR)\ByteLoader.pm

-	-del /f $(LIBDIR)\Devel\Peek.pm $(LIBDIR)\Devel\DProf.pm

-	-del /f $(LIBDIR)\File\Glob.pm

-	-del /f $(LIBDIR)\Storable.pm

-	-if exist $(LIBDIR)\IO rmdir /s /q $(LIBDIR)\IO || rmdir /s $(LIBDIR)\IO

-	-if exist $(LIBDIR)\Thread rmdir /s /q $(LIBDIR)\Thread || rmdir /s $(LIBDIR)\Thread

-	-if exist $(LIBDIR)\B rmdir /s /q $(LIBDIR)\B || rmdir /s $(LIBDIR)\B

-	-if exist $(LIBDIR)\Data rmdir /s /q $(LIBDIR)\Data || rmdir /s $(LIBDIR)\Data

-	-del /f $(PODDIR)\*.html

-	-del /f $(PODDIR)\*.bat

-	-cd ..\utils && del /f h2ph splain perlbug pl2pm c2ph h2xs perldoc \

-	    dprofpp *.bat

-	-cd ..\x2p && del /f find2perl s2p *.bat

-	-del /f ..\config.sh ..\splittree.pl perlmain.c dlutils.c config.h.new

-	-del /f $(CONFIGPM)

-	-del /f bin\*.bat

-	-cd $(EXTDIR) && del /s *$(a) *.def *.map *.pdb *.bs Makefile *$(o) \

-	    pm_to_blib

-	-if exist $(AUTODIR) rmdir /s /q $(AUTODIR) || rmdir /s $(AUTODIR)

-	-if exist $(COREDIR) rmdir /s /q $(COREDIR) || rmdir /s $(COREDIR)

-

-install : all installbare installhtml

-

-installbare : $(RIGHTMAKE) utils

-	$(PERLEXE) ..\installperl

-	if exist $(WPERLEXE) $(XCOPY) $(WPERLEXE) $(INST_BIN)\*.*

-	$(XCOPY) $(GLOBEXE) $(INST_BIN)\*.*

-	$(XCOPY) bin\*.bat $(INST_SCRIPT)\*.*

-

-installhtml : doc

-	$(RCOPY) html\*.* $(INST_HTML)\*.*

-

-inst_lib : $(CONFIGPM)

-	copy splittree.pl .. 

-	$(MINIPERL) -I..\lib ..\splittree.pl "../LIB" $(AUTODIR)

-	$(RCOPY) ..\lib $(INST_LIB)\*.*

-

-minitest : $(MINIPERL) $(GLOBEXE) $(CONFIGPM) utils

-	$(XCOPY) $(MINIPERL) ..\t\perl.exe

-.IF "$(CCTYPE)" == "BORLAND"

-	$(XCOPY) $(GLOBBAT) ..\t\$(NULL)

-.ELSE

-	$(XCOPY) $(GLOBEXE) ..\t\$(NULL)

-.ENDIF

-	attrib -r ..\t\*.*

-	copy test ..\t

-	cd ..\t && \

-	$(MINIPERL) -I..\lib test base/*.t comp/*.t cmd/*.t io/*.t op/*.t pragma/*.t

-

-test-prep : all utils

-	$(XCOPY) $(PERLEXE) ..\t\$(NULL)

-	$(XCOPY) $(PERLDLL) ..\t\$(NULL)

-.IF "$(CCTYPE)" == "BORLAND"

-	$(XCOPY) $(GLOBBAT) ..\t\$(NULL)

-.ELSE

-	$(XCOPY) $(GLOBEXE) ..\t\$(NULL)

-.ENDIF

-

-test : $(RIGHTMAKE) test-prep

-	cd ..\t && $(PERLEXE) -I..\lib harness

-

-test-notty : test-prep

-	set PERL_SKIP_TTY_TEST=1 && \

-	    cd ..\t && $(PERLEXE) -I.\lib harness

-

-test-wide : test-prep

-	set HARNESS_PERL_SWITCHES=-C && \

-	    cd ..\t && $(PERLEXE) -I..\lib harness

-

-test-wide-notty : test-prep

-	set PERL_SKIP_TTY_TEST=1 && \

-	    set HARNESS_PERL_SWITCHES=-C && \

-	    cd ..\t && $(PERLEXE) -I..\lib harness

-

-clean : 

-	-@erase miniperlmain$(o)

-	-@erase $(MINIPERL)

-	-@erase perlglob$(o)

-	-@erase perlmain$(o)

-	-@erase config.w32

-	-@erase /f config.h

-	-@erase $(GLOBEXE)

-	-@erase $(PERLEXE)

-	-@erase $(WPERLEXE)

-	-@erase $(PERLDLL)

-	-@erase $(CORE_OBJ)

-	-if exist $(MINIDIR) rmdir /s /q $(MINIDIR) || rmdir /s $(MINIDIR)

-	-@erase $(WIN32_OBJ)

-	-@erase $(DLL_OBJ)

-	-@erase $(X2P_OBJ)

-	-@erase ..\*$(o) ..\*$(a) ..\*.exp *$(o) *$(a) *.exp *.res

-	-@erase ..\t\*.exe ..\t\*.dll ..\t\*.bat

-	-@erase ..\x2p\*.exe ..\x2p\*.bat

-	-@erase *.ilk

-	-@erase *.pdb

-

-# Handy way to run perlbug -ok without having to install and run the

-# installed perlbug. We don't re-run the tests here - we trust the user.

-# Please *don't* use this unless all tests pass.

-# If you want to report test failures, use "dmake nok" instead.

-ok: utils

-	$(PERLEXE) -I..\lib ..\utils\perlbug -ok -s "(UNINSTALLED)"

-

-okfile: utils

-	$(PERLEXE) -I..\lib ..\utils\perlbug -ok -s "(UNINSTALLED)" -F perl.ok

- 

-nok: utils

-	$(PERLEXE) -I..\lib ..\utils\perlbug -nok -s "(UNINSTALLED)"

- 

-nokfile: utils

-	$(PERLEXE) -I..\lib ..\utils\perlbug -nok -s "(UNINSTALLED)" -F perl.nok

+#
+# Makefile to build perl on Windows NT using DMAKE.
+# Supported compilers:
+#	Visual C++ 2.0 thro 6.0
+#	Borland C++ 5.02
+#	Mingw32 with gcc-2.95.2 or better  **experimental**
+#
+# This is set up to build a perl.exe that runs off a shared library
+# (perl56.dll).  Also makes individual DLLs for the XS extensions.
+#
+
+##
+## Make sure you read README.win32 *before* you mess with anything here!
+##
+
+##
+## Build configuration.  Edit the values below to suit your needs.
+##
+
+#
+# Set these to wherever you want "dmake install" to put your
+# newly built perl.
+#
+INST_DRV	*= c:
+INST_TOP	*= $(INST_DRV)\perl
+
+#
+# Comment this out if you DON'T want your perl installation to be versioned.
+# This means that the new installation will overwrite any files from the
+# old installation at the same INST_TOP location.  Leaving it enabled is
+# the safest route, as perl adds the extra version directory to all the
+# locations it installs files to.  If you disable it, an alternative
+# versioned installation can be obtained by setting INST_TOP above to a
+# path that includes an arbitrary version string.
+#
+INST_VER	*= \5.6.0
+
+#
+# Comment this out if you DON'T want your perl installation to have
+# architecture specific components.  This means that architecture-
+# specific files will be installed along with the architecture-neutral
+# files.  Leaving it enabled is safer and more flexible, in case you
+# want to build multiple flavors of perl and install them together in
+# the same location.  Commenting it out gives you a simpler
+# installation that is easier to understand for beginners.
+#
+INST_ARCH	*= \$(ARCHNAME)
+
+#
+# uncomment to enable multiple interpreters.  This is need for fork()
+# emulation.
+#
+#USE_MULTI	*= define
+
+#
+# Beginnings of interpreter cloning/threads; still very incomplete.
+# This should be enabled to get the fork() emulation.  This needs
+# USE_MULTI as well.
+#
+#USE_ITHREADS	*= define
+
+#
+# uncomment to enable the implicit "host" layer for all system calls
+# made by perl.  This needs USE_MULTI above.  This is also needed to
+# get fork().
+#
+#USE_IMP_SYS	*= define
+
+#
+# WARNING! This option is deprecated and will eventually go away (enable
+# USE_ITHREADS instead).
+#
+# uncomment to enable threads-capabilities.  This is incompatible with
+# USE_ITHREADS, and is only here for people who may have come to rely
+# on the experimental Thread support that was in 5.005.
+#
+#USE_5005THREADS	*= define
+
+#
+# WARNING! This option is deprecated and will eventually go away (enable
+# USE_MULTI instead).
+#
+# uncomment next line if you want to use the PERL_OBJECT build option.
+# DO NOT ENABLE unless you have legacy code that relies on the C++
+# CPerlObj class that was available in 5.005.  This cannot be enabled
+# if you ask for USE_5005THREADS above.
+#
+#USE_OBJECT	*= define
+
+#
+# uncomment exactly one of the following
+# 
+# Visual C++ 2.x
+#CCTYPE		*= MSVC20
+# Visual C++ > 2.x and < 6.x
+#CCTYPE		*= MSVC
+# Visual C++ >= 6.x
+#CCTYPE		*= MSVC60
+# Borland 5.02 or later
+#CCTYPE		*= BORLAND
+# mingw32+gcc-2.95.2 or better
+CCTYPE		*= GCC
+
+#
+# uncomment this if you are compiling under Windows 95/98 and command.com
+# (not needed if you're running under 4DOS/NT 6.01 or later)
+#IS_WIN95	*= define
+
+#
+# uncomment next line if you want debug version of perl (big,slow)
+# If not enabled, we automatically try to use maximum optimization
+# with all compilers that are known to have a working optimizer.
+#
+#CFG		*= Debug
+
+#
+# uncomment to enable use of PerlCRT.DLL when using the Visual C compiler.
+# It has patches that fix known bugs in older versions of MSVCRT.DLL.
+# This currently requires VC 5.0 with Service Pack 3 or later.
+# Get it from CPAN at http://www.perl.com/CPAN/authors/id/D/DO/DOUGL/
+# and follow the directions in the package to install.
+#
+# Not recommended if you have VC 6.x and you're not running Windows 9x.
+#
+#USE_PERLCRT	*= define
+
+#
+# uncomment to enable linking with setargv.obj under the Visual C
+# compiler. Setting this options enables perl to expand wildcards in
+# arguments, but it may be harder to use alternate methods like
+# File::DosGlob that are more powerful.  This option is supported only with
+# Visual C.
+#
+#USE_SETARGV	*= define
+
+#
+# if you have the source for des_fcrypt(), uncomment this and make sure the
+# file exists (see README.win32).  File should be located in the same
+# directory as this file.
+#
+#CRYPT_SRC	*= fcrypt.c
+
+#
+# if you didn't set CRYPT_SRC and if you have des_fcrypt() available in a
+# library, uncomment this, and make sure the library exists (see README.win32)
+# Specify the full pathname of the library.
+#
+#CRYPT_LIB	*= fcrypt.lib
+
+#
+# set this if you wish to use perl's malloc
+# WARNING: Turning this on/off WILL break binary compatibility with extensions
+# you may have compiled with/without it.  Be prepared to recompile all
+# extensions if you change the default.  Currently, this cannot be enabled
+# if you ask for USE_IMP_SYS above.
+#
+#PERL_MALLOC	*= define
+
+#
+# set the install locations of the compiler include/libraries
+# Running VCVARS32.BAT is *required* when using Visual C.
+# Some versions of Visual C don't define MSVCDIR in the environment,
+# so you may have to set CCHOME explicitly (spaces in the path name should
+# not be quoted)
+#
+#CCHOME		*= c:\bc5
+#CCHOME		*= $(MSVCDIR)
+CCHOME		*= c:\gcc-2.95.2-msvcrt
+CCINCDIR	*= $(CCHOME)\include
+CCLIBDIR	*= $(CCHOME)\lib
+
+#
+# Additional compiler flags can be specified here.
+#
+
+#
+# This should normally be disabled.  Adding -DPERL_POLLUTE enables support
+# for old symbols by default, at the expense of extreme pollution.  You most
+# probably just want to build modules that won't compile with
+#         perl Makefile.PL POLLUTE=1
+# instead of enabling this.  Please report such modules to the respective
+# authors.
+#
+#BUILDOPT	+= -DPERL_POLLUTE
+
+#
+# This should normally be disabled.  Enabling it will disable the File::Glob
+# implementation of CORE::glob.
+#
+#BUILDOPT	+= -DPERL_EXTERNAL_GLOB
+
+#
+# This should normally be disabled.  Enabling it causes perl to read scripts
+# in text mode (which is the 5.005 behavior) and will break ByteLoader.
+#BUILDOPT	+= -DPERL_TEXTMODE_SCRIPTS
+
+#
+# specify semicolon-separated list of extra directories that modules will
+# look for libraries (spaces in path names need not be quoted)
+#
+EXTRALIBDIRS	*=
+
+#
+# set this to point to cmd.exe (only needed if you use some
+# alternate shell that doesn't grok cmd.exe style commands)
+#
+#SHELL		*= g:\winnt\system32\cmd.exe
+
+#
+# set this to your email address (perl will guess a value from
+# from your loginname and your hostname, which may not be right)
+#
+#EMAIL		*=
+
+##
+## Build configuration ends.
+##
+
+##################### CHANGE THESE ONLY IF YOU MUST #####################
+
+.IF "$(CRYPT_SRC)$(CRYPT_LIB)" == ""
+D_CRYPT		= undef
+.ELSE
+D_CRYPT		= define
+CRYPT_FLAG	= -DHAVE_DES_FCRYPT
+.ENDIF
+
+.IF "$(USE_OBJECT)" == "define"
+PERL_MALLOC	!= undef
+USE_5005THREADS	!= undef
+USE_MULTI	!= undef
+USE_IMP_SYS	!= define
+.ENDIF
+
+PERL_MALLOC	*= undef
+
+USE_5005THREADS	*= undef
+
+.IF "$(USE_5005THREADS)" == "define"
+USE_ITHREADS	!= undef
+.ENDIF
+
+.IF "$(USE_IMP_SYS)" == "define"
+PERL_MALLOC	!= undef
+.ENDIF
+
+USE_MULTI	*= undef
+USE_OBJECT	*= undef
+USE_ITHREADS	*= undef
+USE_IMP_SYS	*= undef
+USE_PERLCRT	*= undef
+
+.IF "$(USE_IMP_SYS)$(USE_MULTI)$(USE_5005THREADS)$(USE_OBJECT)" == "defineundefundefundef"
+USE_MULTI	!= define
+.ENDIF
+
+.IF "$(USE_ITHREADS)$(USE_MULTI)$(USE_OBJECT)" == "defineundefundef"
+USE_MULTI	!= define
+USE_5005THREADS	!= undef
+.ENDIF
+
+.IF "$(USE_MULTI)$(USE_5005THREADS)$(USE_OBJECT)" != "undefundefundef"
+BUILDOPT	+= -DPERL_IMPLICIT_CONTEXT
+.ENDIF
+
+.IF "$(USE_IMP_SYS)" != "undef"
+BUILDOPT	+= -DPERL_IMPLICIT_SYS
+.ENDIF
+
+.IMPORT .IGNORE : PROCESSOR_ARCHITECTURE
+
+PROCESSOR_ARCHITECTURE *= x86
+
+.IF "$(USE_OBJECT)" == "define"
+ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-object
+.ELIF "$(USE_5005THREADS)" == "define"
+ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-thread
+.ELIF "$(USE_MULTI)" == "define"
+ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)-multi
+.ELSE
+ARCHNAME	= MSWin32-$(PROCESSOR_ARCHITECTURE)
+.ENDIF
+
+.IF "$(USE_ITHREADS)" == "define"
+ARCHNAME	!:= $(ARCHNAME)-thread
+.ENDIF
+
+# Visual Studio 98 specific
+.IF "$(CCTYPE)" == "MSVC60"
+
+# VC 6.0 can load the socket dll on demand.  Makes the test suite
+# run in about 10% less time.
+DELAYLOAD	*= -DELAYLOAD:wsock32.dll -DELAYLOAD:shell32.dll delayimp.lib 
+
+# VC 6.0 seems capable of compiling perl correctly with optimizations
+# enabled.  Anything earlier fails tests.
+CFG		*= Optimize
+.ENDIF
+
+ARCHDIR		= ..\lib\$(ARCHNAME)
+COREDIR		= ..\lib\CORE
+AUTODIR		= ..\lib\auto
+LIBDIR		= ..\lib
+EXTDIR		= ..\ext
+PODDIR		= ..\pod
+EXTUTILSDIR	= $(LIBDIR)\ExtUtils
+
+#
+INST_SCRIPT	= $(INST_TOP)$(INST_VER)\bin
+INST_BIN	= $(INST_SCRIPT)$(INST_ARCH)
+INST_LIB	= $(INST_TOP)$(INST_VER)\lib
+INST_ARCHLIB	= $(INST_LIB)$(INST_ARCH)
+INST_COREDIR	= $(INST_ARCHLIB)\CORE
+INST_POD	= $(INST_LIB)\pod
+INST_HTML	= $(INST_POD)\html
+
+#
+# Programs to compile, build .lib files and link
+#
+
+.USESHELL :
+
+.IF "$(CCTYPE)" == "BORLAND"
+
+CC		= bcc32
+LINK32		= tlink32
+LIB32		= tlib /P128
+IMPLIB		= implib -c
+RSC		= rc
+
+#
+# Options
+#
+INCLUDES	= -I$(COREDIR) -I.\include -I. -I.. -I"$(CCINCDIR)"
+#PCHFLAGS	= -H -Hc -H=c:\temp\bcmoduls.pch 
+DEFINES		= -DWIN32 $(CRYPT_FLAG)
+LOCDEFS		= -DPERLDLL -DPERL_CORE
+SUBSYS		= console
+CXX_FLAG	= -P
+
+LIBC		= cw32mti.lib
+LIBFILES	= $(CRYPT_LIB) import32.lib $(LIBC) odbc32.lib odbccp32.lib
+
+.IF  "$(CFG)" == "Debug"
+OPTIMIZE	= -v -D_RTLDLL -DDEBUGGING
+LINK_DBG	= -v
+.ELSE
+OPTIMIZE	= -O2 -D_RTLDLL
+LINK_DBG	= 
+.ENDIF
+
+CFLAGS		= -w -g0 -tWM -tWD $(INCLUDES) $(DEFINES) $(LOCDEFS) \
+		$(PCHFLAGS) $(OPTIMIZE)
+LINK_FLAGS	= $(LINK_DBG) -L"$(INST_COREDIR)" -L"$(CCLIBDIR)"
+OBJOUT_FLAG	= -o
+EXEOUT_FLAG	= -e
+LIBOUT_FLAG	= 
+
+.ELIF "$(CCTYPE)" == "GCC"
+
+CC		= gcc
+LINK32		= gcc
+LIB32		= ar rc
+IMPLIB		= dlltool
+RSC		= rc
+
+o = .o
+a = .a
+
+#
+# Options
+#
+
+INCLUDES	= -I$(COREDIR) -I.\include -I. -I..
+DEFINES		= -DWIN32 $(CRYPT_FLAG)
+LOCDEFS		= -DPERLDLL -DPERL_CORE
+SUBSYS		= console
+CXX_FLAG	= -xc++
+
+LIBC		= -lmsvcrt
+
+# same libs as MSVC
+LIBFILES	= $(CRYPT_LIB) $(LIBC) \
+		  -lmoldname -lkernel32 -luser32 -lgdi32 \
+		  -lwinspool -lcomdlg32 -ladvapi32 -lshell32 -lole32 \
+		  -loleaut32 -lnetapi32 -luuid -lwsock32 -lmpr \
+		  -lwinmm -lversion -lodbc32
+
+.IF  "$(CFG)" == "Debug"
+OPTIMIZE	= -g -DDEBUGGING
+LINK_DBG	= -g
+.ELSE
+OPTIMIZE	= -g -O2
+LINK_DBG	= 
+.ENDIF
+
+CFLAGS		= $(INCLUDES) $(DEFINES) $(LOCDEFS) $(OPTIMIZE)
+LINK_FLAGS	= $(LINK_DBG) -L"$(INST_COREDIR)" -L"$(CCLIBDIR)"
+OBJOUT_FLAG	= -o
+EXEOUT_FLAG	= -o
+LIBOUT_FLAG	= 
+
+# NOTE: we assume that GCC uses MSVCRT.DLL
+BUILDOPT	+= -fno-strict-aliasing -DPERL_MSVCRT_READFIX
+
+.ELSE
+
+CC		= cl
+LINK32		= link
+LIB32		= $(LINK32) -lib
+RSC		= rc
+
+#
+# Options
+#
+
+INCLUDES	= -I$(COREDIR) -I.\include -I. -I..
+#PCHFLAGS	= -Fpc:\temp\vcmoduls.pch -YX 
+DEFINES		= -DWIN32 -D_CONSOLE -DNO_STRICT $(CRYPT_FLAG)
+LOCDEFS		= -DPERLDLL -DPERL_CORE
+SUBSYS		= console
+CXX_FLAG	= -TP -GX
+
+.IF "$(USE_PERLCRT)" != "define"
+LIBC	= msvcrt.lib
+.ELSE
+LIBC	= PerlCRT.lib
+.ENDIF
+
+PERLEXE_RES	=
+PERLDLL_RES	=
+
+.IF  "$(CFG)" == "Debug"
+.IF "$(CCTYPE)" == "MSVC20"
+OPTIMIZE	= -Od -MD -Z7 -DDEBUGGING
+.ELSE
+OPTIMIZE	= -Od -MD -Zi -DDEBUGGING
+.ENDIF
+LINK_DBG	= -debug -pdb:none
+.ELSE
+.IF "$(CFG)" == "Optimize"
+# -O1 yields smaller code, which turns out to be faster than -O2
+#OPTIMIZE	= -O2 -MD -DNDEBUG
+OPTIMIZE	= -O1 -MD -DNDEBUG
+.ELSE
+OPTIMIZE	= -Od -MD -DNDEBUG
+.ENDIF
+LINK_DBG	= -release
+.ENDIF
+
+LIBBASEFILES	= $(CRYPT_LIB) \
+		oldnames.lib kernel32.lib user32.lib gdi32.lib winspool.lib \
+		comdlg32.lib advapi32.lib shell32.lib ole32.lib oleaut32.lib \
+		netapi32.lib uuid.lib wsock32.lib mpr.lib winmm.lib \
+		version.lib odbc32.lib odbccp32.lib
+
+# we add LIBC here, since we may be using PerlCRT.dll
+LIBFILES	= $(LIBBASEFILES) $(LIBC)
+
+CFLAGS		= -nologo -Gf -W3 $(INCLUDES) $(DEFINES) $(LOCDEFS) \
+		$(PCHFLAGS) $(OPTIMIZE)
+LINK_FLAGS	= -nologo -nodefaultlib $(LINK_DBG) \
+		-libpath:"$(INST_COREDIR)" \
+		-machine:$(PROCESSOR_ARCHITECTURE)
+OBJOUT_FLAG	= -Fo
+EXEOUT_FLAG	= -Fe
+LIBOUT_FLAG	= /out:
+
+.IF "$(USE_PERLCRT)" != "define"
+BUILDOPT	+= -DPERL_MSVCRT_READFIX
+.ENDIF
+
+.ENDIF
+
+.IF "$(USE_OBJECT)" == "define"
+OPTIMIZE	+= $(CXX_FLAG)
+BUILDOPT	+= -DPERL_OBJECT
+.ENDIF
+
+CFLAGS_O	= $(CFLAGS) $(BUILDOPT)
+
+# used to allow local linking flags that are not propogated into Config.pm,
+# currently unused
+#   -- BKS, 12-12-1999
+PRIV_LINK_FLAGS	*=
+BLINK_FLAGS	= $(PRIV_LINK_FLAGS) $(LINK_FLAGS)
+
+#################### do not edit below this line #######################
+############# NO USER-SERVICEABLE PARTS BEYOND THIS POINT ##############
+
+o *= .obj
+a *= .lib
+
+LKPRE		= INPUT (
+LKPOST		= )
+
+#
+# Rules
+# 
+
+.SUFFIXES : .c $(o) .dll $(a) .exe .rc .res
+
+.c$(o):
+	$(CC) -c $(null,$(<:d) $(NULL) -I$(<:d)) $(CFLAGS_O) $(OBJOUT_FLAG)$@ $<
+
+.y.c:
+	$(NOOP)
+
+$(o).dll:
+.IF "$(CCTYPE)" == "BORLAND"
+	$(LINK32) -Tpd -ap $(BLINK_FLAGS) c0d32$(o) $<,$@,,$(LIBFILES),$(*B).def
+	$(IMPLIB) $(*B).lib $@
+.ELIF "$(CCTYPE)" == "GCC"
+	$(LINK32) -o $@ $(BLINK_FLAGS) $< $(LIBFILES)
+	$(IMPLIB) --input-def $(*B).def --output-lib $(*B).a $@
+.ELSE
+	$(LINK32) -dll -subsystem:windows -implib:$(*B).lib -def:$(*B).def \
+	    -out:$@ $(BLINK_FLAGS) $(LIBFILES) $< $(LIBPERL)  
+.ENDIF
+
+.rc.res:
+	$(RSC) -i.. $<
+
+#
+# various targets
+MINIPERL	= ..\miniperl.exe
+MINIDIR		= .\mini
+PERLEXE		= ..\perl.exe
+WPERLEXE	= ..\wperl.exe
+GLOBEXE		= ..\perlglob.exe
+CONFIGPM	= ..\lib\Config.pm
+MINIMOD		= ..\lib\ExtUtils\Miniperl.pm
+X2P		= ..\x2p\a2p.exe
+
+PL2BAT		= bin\pl2bat.pl
+GLOBBAT		= bin\perlglob.bat
+
+UTILS		=			\
+		..\utils\h2ph		\
+		..\utils\splain		\
+		..\utils\dprofpp	\
+		..\utils\perlbug	\
+		..\utils\pl2pm 		\
+		..\utils\c2ph		\
+		..\utils\h2xs		\
+		..\utils\perldoc	\
+		..\utils\perlcc		\
+		..\pod\checkpods	\
+		..\pod\pod2html		\
+		..\pod\pod2latex	\
+		..\pod\pod2man		\
+		..\pod\pod2text		\
+		..\pod\pod2usage	\
+		..\pod\podchecker	\
+		..\pod\podselect	\
+		..\x2p\find2perl	\
+		..\x2p\s2p		\
+		bin\exetype.pl		\
+		bin\runperl.pl		\
+		bin\pl2bat.pl		\
+		bin\perlglob.pl		\
+		bin\search.pl
+
+.IF "$(CCTYPE)" == "BORLAND"
+
+CFGSH_TMPL	= config.bc
+CFGH_TMPL	= config_H.bc
+
+.ELIF "$(CCTYPE)" == "GCC"
+
+CFGSH_TMPL	= config.gc
+CFGH_TMPL	= config_H.gc
+PERLIMPLIB	= ..\libperl56$(a)
+
+.ELSE
+
+CFGSH_TMPL	= config.vc
+CFGH_TMPL	= config_H.vc
+
+.ENDIF
+
+PERLIMPLIB	*= ..\perl56$(a)
+PERLDLL		= ..\perl56.dll
+
+XCOPY		= xcopy /f /r /i /d
+RCOPY		= xcopy /f /r /i /e /d
+NOOP		= @echo
+
+#
+# filenames given to xsubpp must have forward slashes (since it puts
+# full pathnames in #line strings)
+XSUBPP		= ..\$(MINIPERL) -I..\..\lib ..\$(EXTUTILSDIR)\xsubpp \
+		-C++ -prototypes
+
+MICROCORE_SRC	=		\
+		..\av.c		\
+		..\deb.c	\
+		..\doio.c	\
+		..\doop.c	\
+		..\dump.c	\
+		..\globals.c	\
+		..\gv.c		\
+		..\hv.c		\
+		..\mg.c		\
+		..\op.c		\
+		..\perl.c	\
+		..\perlapi.c	\
+		..\perly.c	\
+		..\pp.c		\
+		..\pp_ctl.c	\
+		..\pp_hot.c	\
+		..\pp_sys.c	\
+		..\regcomp.c	\
+		..\regexec.c	\
+		..\run.c	\
+		..\scope.c	\
+		..\sv.c		\
+		..\taint.c	\
+		..\toke.c	\
+		..\universal.c	\
+		..\utf8.c	\
+		..\util.c	\
+		..\xsutils.c
+
+EXTRACORE_SRC	+= perllib.c
+
+.IF "$(PERL_MALLOC)" == "define"
+EXTRACORE_SRC	+= ..\malloc.c
+.ENDIF
+
+.IF "$(USE_OBJECT)" != "define"
+EXTRACORE_SRC	+= ..\perlio.c
+.ENDIF
+
+WIN32_SRC	=		\
+		.\win32.c	\
+		.\win32sck.c	\
+		.\win32thread.c 
+
+.IF "$(CRYPT_SRC)" != ""
+WIN32_SRC	+= .\$(CRYPT_SRC)
+.ENDIF
+
+DLL_SRC		= $(DYNALOADER).c
+
+X2P_SRC		=		\
+		..\x2p\a2p.c	\
+		..\x2p\hash.c	\
+		..\x2p\str.c	\
+		..\x2p\util.c	\
+		..\x2p\walk.c
+
+CORE_NOCFG_H	=		\
+		..\av.h		\
+		..\cop.h	\
+		..\cv.h		\
+		..\dosish.h	\
+		..\embed.h	\
+		..\form.h	\
+		..\gv.h		\
+		..\handy.h	\
+		..\hv.h		\
+		..\iperlsys.h	\
+		..\mg.h		\
+		..\nostdio.h	\
+		..\op.h		\
+		..\opcode.h	\
+		..\perl.h	\
+		..\perlapi.h	\
+		..\perlsdio.h	\
+		..\perlsfio.h	\
+		..\perly.h	\
+		..\pp.h		\
+		..\proto.h	\
+		..\regexp.h	\
+		..\scope.h	\
+		..\sv.h		\
+		..\thread.h	\
+		..\unixish.h	\
+		..\utf8.h	\
+		..\util.h	\
+		..\warnings.h	\
+		..\XSUB.h	\
+		..\EXTERN.h	\
+		..\perlvars.h	\
+		..\intrpvar.h	\
+		..\thrdvar.h	\
+		.\include\dirent.h	\
+		.\include\netdb.h	\
+		.\include\sys\socket.h	\
+		.\win32.h
+
+CORE_H		= $(CORE_NOCFG_H) .\config.h
+
+MICROCORE_OBJ	= $(MICROCORE_SRC:db:+$(o))
+CORE_OBJ	= $(MICROCORE_OBJ) $(EXTRACORE_SRC:db:+$(o))
+WIN32_OBJ	= $(WIN32_SRC:db:+$(o))
+MINICORE_OBJ	= $(MINIDIR)\{$(MICROCORE_OBJ:f) miniperlmain$(o) perlio$(o)}
+MINIWIN32_OBJ	= $(MINIDIR)\{$(WIN32_OBJ:f)}
+MINI_OBJ	= $(MINICORE_OBJ) $(MINIWIN32_OBJ)
+DLL_OBJ		= $(DLL_SRC:db:+$(o))
+X2P_OBJ		= $(X2P_SRC:db:+$(o))
+
+PERLDLL_OBJ	= $(CORE_OBJ)
+PERLEXE_OBJ	= perlmain$(o)
+
+PERLDLL_OBJ	+= $(WIN32_OBJ) $(DLL_OBJ)
+
+.IF "$(USE_SETARGV)" != ""
+SETARGV_OBJ	= setargv$(o)
+.ENDIF
+
+DYNAMIC_EXT	= Socket IO Fcntl Opcode SDBM_File POSIX attrs Thread B re \
+		Data/Dumper Devel/Peek ByteLoader Devel/DProf File/Glob \
+		Sys/Hostname Storable
+STATIC_EXT	= DynaLoader
+NONXS_EXT	= Errno
+
+DYNALOADER	= $(EXTDIR)\DynaLoader\DynaLoader
+SOCKET		= $(EXTDIR)\Socket\Socket
+FCNTL		= $(EXTDIR)\Fcntl\Fcntl
+OPCODE		= $(EXTDIR)\Opcode\Opcode
+SDBM_FILE	= $(EXTDIR)\SDBM_File\SDBM_File
+IO		= $(EXTDIR)\IO\IO
+POSIX		= $(EXTDIR)\POSIX\POSIX
+ATTRS		= $(EXTDIR)\attrs\attrs
+THREAD		= $(EXTDIR)\Thread\Thread
+B		= $(EXTDIR)\B\B
+RE		= $(EXTDIR)\re\re
+DUMPER		= $(EXTDIR)\Data\Dumper\Dumper
+ERRNO		= $(EXTDIR)\Errno\Errno
+PEEK		= $(EXTDIR)\Devel\Peek\Peek
+BYTELOADER	= $(EXTDIR)\ByteLoader\ByteLoader
+DPROF		= $(EXTDIR)\Devel\DProf\DProf
+GLOB		= $(EXTDIR)\File\Glob\Glob
+HOSTNAME	= $(EXTDIR)\Sys\Hostname\Hostname
+STORABLE	= $(EXTDIR)\Storable\Storable
+
+SOCKET_DLL	= $(AUTODIR)\Socket\Socket.dll
+FCNTL_DLL	= $(AUTODIR)\Fcntl\Fcntl.dll
+OPCODE_DLL	= $(AUTODIR)\Opcode\Opcode.dll
+SDBM_FILE_DLL	= $(AUTODIR)\SDBM_File\SDBM_File.dll
+IO_DLL		= $(AUTODIR)\IO\IO.dll
+POSIX_DLL	= $(AUTODIR)\POSIX\POSIX.dll
+ATTRS_DLL	= $(AUTODIR)\attrs\attrs.dll
+THREAD_DLL	= $(AUTODIR)\Thread\Thread.dll
+B_DLL		= $(AUTODIR)\B\B.dll
+DUMPER_DLL	= $(AUTODIR)\Data\Dumper\Dumper.dll
+PEEK_DLL	= $(AUTODIR)\Devel\Peek\Peek.dll
+RE_DLL		= $(AUTODIR)\re\re.dll
+BYTELOADER_DLL	= $(AUTODIR)\ByteLoader\ByteLoader.dll
+DPROF_DLL	= $(AUTODIR)\Devel\DProf\DProf.dll
+GLOB_DLL	= $(AUTODIR)\File\Glob\Glob.dll
+HOSTNAME_DLL	= $(AUTODIR)\Sys\Hostname\Hostname.dll
+STORABLE_DLL	= $(AUTODIR)\Storable\Storable.dll
+
+ERRNO_PM	= $(LIBDIR)\Errno.pm
+
+EXTENSION_C	=		\
+		$(SOCKET).c	\
+		$(FCNTL).c	\
+		$(OPCODE).c	\
+		$(SDBM_FILE).c	\
+		$(IO).c		\
+		$(POSIX).c	\
+		$(ATTRS).c	\
+		$(THREAD).c	\
+		$(RE).c		\
+		$(DUMPER).c	\
+		$(PEEK).c	\
+		$(B).c		\
+		$(BYTELOADER).c	\
+		$(DPROF).c	\
+		$(GLOB).c	\
+		$(HOSTNAME).c	\
+		$(STORABLE).c
+
+EXTENSION_DLL	=		\
+		$(SOCKET_DLL)	\
+		$(FCNTL_DLL)	\
+		$(OPCODE_DLL)	\
+		$(SDBM_FILE_DLL)\
+		$(IO_DLL)	\
+		$(POSIX_DLL)	\
+		$(ATTRS_DLL)	\
+		$(DUMPER_DLL)	\
+		$(PEEK_DLL)	\
+		$(B_DLL)	\
+		$(RE_DLL)	\
+		$(THREAD_DLL)	\
+		$(BYTELOADER_DLL)	\
+		$(DPROF_DLL)	\
+		$(GLOB_DLL)	\
+		$(HOSTNAME_DLL)	\
+		$(STORABLE_DLL)
+
+EXTENSION_PM	=		\
+		$(ERRNO_PM)
+
+POD2HTML	= $(PODDIR)\pod2html
+POD2MAN		= $(PODDIR)\pod2man
+POD2LATEX	= $(PODDIR)\pod2latex
+POD2TEXT	= $(PODDIR)\pod2text
+
+# vars must be separated by "\t+~\t+", since we're using the tempfile
+# version of config_sh.pl (we were overflowing someone's buffer by
+# trying to fit them all on the command line)
+#	-- BKS 10-17-1999
+CFG_VARS	=					\
+		INST_DRV=$(INST_DRV)		~	\
+		INST_TOP=$(INST_TOP:s/\/\\/)	~	\
+		INST_VER=$(INST_VER:s/\/\\/)	~	\
+		INST_ARCH=$(INST_ARCH)		~	\
+		archname=$(ARCHNAME)		~	\
+		cc=$(CC)			~	\
+		ccflags=$(OPTIMIZE) $(DEFINES) $(BUILDOPT)	~	\
+		cf_email=$(EMAIL)		~	\
+		d_crypt=$(D_CRYPT)		~	\
+		d_mymalloc=$(PERL_MALLOC)	~	\
+		libs=$(LIBFILES:f)		~	\
+		incpath=$(CCINCDIR:s/\/\\/)	~	\
+		libperl=$(PERLIMPLIB:f)		~	\
+		libpth=$(CCLIBDIR:s/\/\\/);$(EXTRALIBDIRS:s/\/\\/)	~	\
+		libc=$(LIBC)			~	\
+		make=dmake			~	\
+		_o=$(o)	obj_ext=$(o)		~	\
+		_a=$(a)	lib_ext=$(a)		~	\
+		static_ext=$(STATIC_EXT)	~	\
+		dynamic_ext=$(DYNAMIC_EXT)	~	\
+		nonxs_ext=$(NONXS_EXT)		~	\
+		use5005threads=$(USE_5005THREADS)	~	\
+		useithreads=$(USE_ITHREADS)	~	\
+		usethreads=$(USE_5005THREADS)	~	\
+		usemultiplicity=$(USE_MULTI)	~	\
+		LINK_FLAGS=$(LINK_FLAGS:s/\/\\/)		~	\
+		optimize=$(OPTIMIZE)
+
+#
+# set up targets varying between Win95 and WinNT builds
+#
+
+.IF "$(IS_WIN95)" == "define"
+MK2 		= .\makefile.95
+RIGHTMAKE	= __switch_makefiles
+NOOP		= @rem
+.ELSE
+MK2		= __not_needed
+RIGHTMAKE	= __not_needed
+.ENDIF
+
+#
+# Top targets
+#
+
+all : .\config.h $(GLOBEXE) $(MINIPERL) $(MK2)		\
+	$(RIGHTMAKE) $(MINIMOD) $(CONFIGPM) $(PERLEXE)	\
+	$(X2P) $(EXTENSION_DLL) $(EXTENSION_PM)
+
+$(DYNALOADER)$(o) : $(DYNALOADER).c $(CORE_H) $(EXTDIR)\DynaLoader\dlutils.c
+
+#----------------------------------------------------------------
+
+#-------------------- BEGIN Win95 SPECIFIC ----------------------
+
+# this target is a jump-off point for Win95
+#  1. it switches to the Win95-specific makefile if it exists
+#     (__do_switch_makefiles)
+#  2. it prints a message when the Win95-specific one finishes (__done)
+#  3. it then kills this makefile by trying to make __no_such_target
+
+__switch_makefiles: __do_switch_makefiles __done __no_such_target
+
+__do_switch_makefiles:
+.IF "$(NOTFIRST)" != "true"
+	if exist $(MK2) $(MAKE:s/-S//) -f $(MK2) $(MAKETARGETS) NOTFIRST=true
+.ELSE
+	$(NOOP)
+.ENDIF
+
+.IF "$(NOTFIRST)" != "true"
+__done:
+	@echo Build process complete. Ignore any errors after this message.
+	@echo Run "dmake test" to test and "dmake install" to install
+
+.ELSE
+# dummy targets for Win95-specific makefile
+
+__done:
+	$(NOOP)
+
+__no_such_target:
+	$(NOOP)
+
+.ENDIF
+
+# This target is used to generate the new makefile (.\makefile.95) for Win95
+
+.\makefile.95: .\makefile.mk
+	$(MINIPERL) genmk95.pl makefile.mk $(MK2)
+
+#--------------------- END Win95 SPECIFIC ---------------------
+
+# a blank target for when builds don't need to do certain things
+# this target added for Win95 port but used to keep the WinNT port able to 
+# use this file
+__not_needed:
+	$(NOOP)
+
+$(GLOBEXE) : perlglob$(o)
+.IF "$(CCTYPE)" == "BORLAND"
+	$(CC) -c -w -v -tWM -I"$(CCINCDIR)" perlglob.c
+	$(LINK32) -Tpe -ap $(BLINK_FLAGS) c0x32$(o) perlglob$(o) \
+	    "$(CCLIBDIR)\32BIT\wildargs$(o)",$@,,import32.lib cw32mt.lib,
+.ELIF "$(CCTYPE)" == "GCC"
+	$(LINK32) $(BLINK_FLAGS) -mconsole -o $@ perlglob$(o) $(LIBFILES)
+.ELSE
+	$(LINK32) $(BLINK_FLAGS) $(LIBFILES) -out:$@ -subsystem:$(SUBSYS) \
+	    perlglob$(o) setargv$(o) 
+.ENDIF
+
+perlglob$(o)  : perlglob.c
+
+config.w32 : $(CFGSH_TMPL)
+	copy $(CFGSH_TMPL) config.w32
+
+.\config.h : $(CFGH_TMPL) $(CORE_NOCFG_H)
+	-del /f config.h
+	copy $(CFGH_TMPL) config.h
+
+..\config.sh : config.w32 $(MINIPERL) config_sh.PL
+	$(MINIPERL) -I..\lib config_sh.PL --cfgsh-option-file \
+	    $(mktmp $(CFG_VARS)) config.w32 > ..\config.sh
+
+# this target is for when changes to the main config.sh happen
+# edit config.{b,v,g}c and make this target once for each supported
+# compiler (e.g. `dmake CCTYPE=BORLAND regen_config_h`)
+regen_config_h:
+	perl config_sh.PL --cfgsh-option-file $(mktmp $(CFG_VARS)) \
+	    $(CFGSH_TMPL) > ..\config.sh
+	-cd .. && del /f perl.exe
+	cd .. && perl configpm
+	-del /f $(CFGH_TMPL)
+	-mkdir $(COREDIR)
+	-perl -I..\lib config_h.PL "INST_VER=$(INST_VER)"
+	rename config.h $(CFGH_TMPL)
+
+$(CONFIGPM) : $(MINIPERL) ..\config.sh config_h.PL ..\minimod.pl
+	cd .. && miniperl configpm
+	if exist lib\* $(RCOPY) lib\*.* ..\lib\$(NULL)
+	$(XCOPY) ..\*.h $(COREDIR)\*.*
+	$(XCOPY) *.h $(COREDIR)\*.*
+	$(XCOPY) ..\ext\re\re.pm $(LIBDIR)\*.*
+	$(RCOPY) include $(COREDIR)\*.*
+	$(MINIPERL) -I..\lib config_h.PL "INST_VER=$(INST_VER)" \
+	    || $(MAKE) $(MAKEMACROS) $(CONFIGPM) $(MAKEFILE)
+
+$(MINIPERL) : $(MINIDIR) $(MINI_OBJ) $(CRTIPMLIBS)
+.IF "$(CCTYPE)" == "BORLAND"
+	$(LINK32) -Tpe -ap $(BLINK_FLAGS) \
+	    @$(mktmp c0x32$(o) $(MINI_OBJ:s,\,\\),$(@:s,\,\\),,$(LIBFILES),)
+.ELIF "$(CCTYPE)" == "GCC"
+	$(LINK32) -v -mconsole -o $@ $(BLINK_FLAGS) \
+	    $(mktmp $(LKPRE) $(MINI_OBJ:s,\,\\) $(LIBFILES) $(LKPOST)) 
+.ELSE
+	$(LINK32) -subsystem:console -out:$@ \
+	    @$(mktmp $(BLINK_FLAGS) $(LIBFILES) $(MINI_OBJ:s,\,\\))
+.ENDIF
+
+$(MINIDIR) :
+	if not exist "$(MINIDIR)" mkdir "$(MINIDIR)"
+
+$(MINICORE_OBJ) : $(CORE_NOCFG_H)
+	$(CC) -c $(CFLAGS) -DPERL_EXTERNAL_GLOB $(OBJOUT_FLAG)$@ ..\$(*B).c
+
+$(MINIWIN32_OBJ) : $(CORE_NOCFG_H)
+	$(CC) -c $(CFLAGS) $(OBJOUT_FLAG)$@ $(*B).c
+
+# -DPERL_IMPLICIT_SYS needs C++ for perllib.c
+# rules wrapped in .IFs break Win9X build (we end up with unbalanced []s unless
+# unless the .IF is true), so instead we use a .ELSE with the default.
+# This is the only file that depends on perlhost.h, vmem.h, and vdir.h
+
+perllib$(o)	: perllib.c .\perlhost.h .\vdir.h .\vmem.h
+.IF "$(USE_IMP_SYS)$(USE_OBJECT)" == "defineundef"
+	$(CC) -c -I. $(CFLAGS_O) $(CXX_FLAG) $(OBJOUT_FLAG)$@ perllib.c
+.ELSE
+	$(CC) -c -I. $(CFLAGS_O) $(OBJOUT_FLAG)$@ perllib.c
+.ENDIF
+
+# 1. we don't want to rebuild miniperl.exe when config.h changes
+# 2. we don't want to rebuild miniperl.exe with non-default config.h
+$(MINI_OBJ)	: $(CORE_NOCFG_H)
+
+$(WIN32_OBJ)	: $(CORE_H)
+$(CORE_OBJ)	: $(CORE_H)
+$(DLL_OBJ)	: $(CORE_H)
+$(X2P_OBJ)	: $(CORE_H)
+
+perldll.def : $(MINIPERL) $(CONFIGPM) ..\global.sym ..\pp.sym ..\makedef.pl
+	$(MINIPERL) -w ..\makedef.pl PLATFORM=win32 $(OPTIMIZE) $(DEFINES) \
+	$(BUILDOPT) CCTYPE=$(CCTYPE) > perldll.def
+
+$(PERLDLL): perldll.def $(PERLDLL_OBJ) $(PERLDLL_RES)
+.IF "$(CCTYPE)" == "BORLAND"
+	$(LINK32) -Tpd -ap $(BLINK_FLAGS) \
+	    @$(mktmp c0d32$(o) $(PERLDLL_OBJ:s,\,\\)\n \
+		$@,\n \
+		$(LIBFILES)\n \
+		perldll.def\n)
+	$(IMPLIB) $*.lib $@
+.ELIF "$(CCTYPE)" == "GCC"
+	$(LINK32) -mdll -o $@ -Wl,--base-file -Wl,perl.base $(BLINK_FLAGS) \
+	    $(mktmp $(LKPRE) $(PERLDLL_OBJ:s,\,\\) $(LIBFILES) $(LKPOST))
+	dlltool --output-lib $(PERLIMPLIB) \
+		--dllname $(PERLDLL:b).dll \
+		--def perldll.def \
+		--base-file perl.base \
+		--output-exp perl.exp
+	$(LINK32) -mdll -o $@ $(BLINK_FLAGS) \
+	    $(mktmp $(LKPRE) $(PERLDLL_OBJ:s,\,\\) $(LIBFILES) \
+		perl.exp $(LKPOST))
+.ELSE
+	$(LINK32) -dll -def:perldll.def -out:$@ \
+	    @$(mktmp -base:0x28000000 $(BLINK_FLAGS) $(DELAYLOAD) $(LIBFILES) \
+	        $(PERLDLL_RES) $(PERLDLL_OBJ:s,\,\\))
+.ENDIF
+	$(XCOPY) $(PERLIMPLIB) $(COREDIR)
+
+$(MINIMOD) : $(MINIPERL) ..\minimod.pl
+	cd .. && miniperl minimod.pl > lib\ExtUtils\Miniperl.pm
+
+..\x2p\a2p$(o) : ..\x2p\a2p.c
+	$(CC) -I..\x2p $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\a2p.c
+
+..\x2p\hash$(o) : ..\x2p\hash.c
+	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\hash.c
+
+..\x2p\str$(o) : ..\x2p\str.c
+	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\str.c
+
+..\x2p\util$(o) : ..\x2p\util.c
+	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\util.c
+
+..\x2p\walk$(o) : ..\x2p\walk.c
+	$(CC) -I..\x2p  $(CFLAGS) $(OBJOUT_FLAG)$@ -c ..\x2p\walk.c
+
+$(X2P) : $(MINIPERL) $(X2P_OBJ)
+	$(MINIPERL) ..\x2p\find2perl.PL
+	$(MINIPERL) ..\x2p\s2p.PL
+.IF "$(CCTYPE)" == "BORLAND"
+	$(LINK32) -Tpe -ap $(BLINK_FLAGS) \
+	    @$(mktmp c0x32$(o) $(X2P_OBJ:s,\,\\),$(@:s,\,\\),,$(LIBFILES),)
+.ELIF "$(CCTYPE)" == "GCC"
+	$(LINK32) -v -o $@ $(BLINK_FLAGS) \
+	    $(mktmp $(LKPRE) $(X2P_OBJ:s,\,\\) $(LIBFILES) $(LKPOST))
+.ELSE
+	$(LINK32) -subsystem:console -out:$@ \
+	    @$(mktmp $(BLINK_FLAGS) $(LIBFILES) $(X2P_OBJ:s,\,\\))
+.ENDIF
+
+perlmain.c : runperl.c 
+	copy runperl.c perlmain.c
+
+perlmain$(o) : perlmain.c
+	$(CC) $(CFLAGS_O) -UPERLDLL $(OBJOUT_FLAG)$@ -c perlmain.c
+
+$(PERLEXE): $(PERLDLL) $(CONFIGPM) $(PERLEXE_OBJ) $(PERLEXE_RES)
+.IF "$(CCTYPE)" == "BORLAND"
+	$(LINK32) -Tpe -ap $(BLINK_FLAGS) \
+	    @$(mktmp c0x32$(o) $(PERLEXE_OBJ:s,\,\\)\n \
+	    $(@:s,\,\\),\n \
+	    $(PERLIMPLIB) $(LIBFILES)\n)
+.ELIF "$(CCTYPE)" == "GCC"
+	$(LINK32) -mconsole -o $@ $(BLINK_FLAGS)  \
+	    $(PERLEXE_OBJ) $(PERLIMPLIB) $(LIBFILES)
+.ELSE
+	$(LINK32) -subsystem:console -out:$@ -stack:0x1000000 $(BLINK_FLAGS) \
+	    $(LIBFILES) $(PERLEXE_OBJ) $(SETARGV_OBJ) $(PERLIMPLIB) $(PERLEXE_RES)
+.ENDIF
+	copy $(PERLEXE) $(WPERLEXE)
+	$(MINIPERL) -I..\lib bin\exetype.pl $(WPERLEXE) WINDOWS
+	copy splittree.pl .. 
+	$(MINIPERL) -I..\lib ..\splittree.pl "../LIB" $(AUTODIR)
+
+$(DYNALOADER).c: $(MINIPERL) $(EXTDIR)\DynaLoader\dl_win32.xs $(CONFIGPM)
+	if not exist $(AUTODIR) mkdir $(AUTODIR)
+	cd $(EXTDIR)\$(*B) && ..\$(MINIPERL) -I..\..\lib $(*B)_pm.PL
+	cd $(EXTDIR)\$(*B) && ..\$(MINIPERL) -I..\..\lib XSLoader_pm.PL
+	$(XCOPY) $(EXTDIR)\$(*B)\$(*B).pm $(LIBDIR)\$(NULL)
+	$(XCOPY) $(EXTDIR)\$(*B)\XSLoader.pm $(LIBDIR)\$(NULL)
+	cd $(EXTDIR)\$(*B) && $(XSUBPP) dl_win32.xs > $(*B).c
+	$(XCOPY) $(EXTDIR)\$(*B)\dlutils.c .
+
+$(EXTDIR)\DynaLoader\dl_win32.xs: dl_win32.xs
+	copy dl_win32.xs $(EXTDIR)\DynaLoader\dl_win32.xs
+
+$(DUMPER_DLL): $(PERLEXE) $(DUMPER).xs
+	cd $(EXTDIR)\Data\$(*B) && \
+	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\Data\$(*B) && $(MAKE)
+
+$(DPROF_DLL): $(PERLEXE) $(DPROF).xs
+	cd $(EXTDIR)\Devel\$(*B) && \
+	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\Devel\$(*B) && $(MAKE)
+
+$(GLOB_DLL): $(PERLEXE) $(GLOB).xs
+	cd $(EXTDIR)\File\$(*B) && \
+	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\File\$(*B) && $(MAKE)
+
+$(PEEK_DLL): $(PERLEXE) $(PEEK).xs
+	cd $(EXTDIR)\Devel\$(*B) && \
+	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\Devel\$(*B) && $(MAKE)
+
+$(RE_DLL): $(PERLEXE) $(RE).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(B_DLL): $(PERLEXE) $(B).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(THREAD_DLL): $(PERLEXE) $(THREAD).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(ATTRS_DLL): $(PERLEXE) $(ATTRS).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(POSIX_DLL): $(PERLEXE) $(POSIX).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(IO_DLL): $(PERLEXE) $(IO).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(SDBM_FILE_DLL) : $(PERLEXE) $(SDBM_FILE).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(FCNTL_DLL): $(PERLEXE) $(FCNTL).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(OPCODE_DLL): $(PERLEXE) $(OPCODE).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(SOCKET_DLL): $(PERLEXE) $(SOCKET).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(HOSTNAME_DLL): $(PERLEXE) $(HOSTNAME).xs
+	cd $(EXTDIR)\Sys\$(*B) && \
+	..\..\..\miniperl -I..\..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\Sys\$(*B) && $(MAKE)
+
+$(BYTELOADER_DLL): $(PERLEXE) $(BYTELOADER).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(STORABLE_DLL): $(PERLEXE) $(STORABLE).xs
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+$(ERRNO_PM): $(PERLEXE) $(ERRNO)_pm.PL
+	cd $(EXTDIR)\$(*B) && \
+	..\..\miniperl -I..\..\lib Makefile.PL INSTALLDIRS=perl
+	cd $(EXTDIR)\$(*B) && $(MAKE)
+
+doc: $(PERLEXE)
+	$(PERLEXE) -I..\lib ..\installhtml --podroot=.. --htmldir=./html \
+	    --podpath=pod:lib:ext:utils --htmlroot="file://$(INST_HTML:s,:,|,)"\
+	    --libpod=perlfunc:perlguts:perlvar:perlrun:perlop --recurse
+
+utils: $(PERLEXE) $(X2P)
+	cd ..\utils && $(MAKE) PERL=$(MINIPERL)
+	copy ..\README.amiga ..\pod\perlamiga.pod
+	copy ..\README.cygwin ..\pod\perlcygwin.pod
+	copy ..\README.dos ..\pod\perldos.pod
+	copy ..\README.hpux ..\pod\perlhpux.pod
+	copy ..\README.machten ..\pod\perlmachten.pod
+	copy ..\README.os2 ..\pod\perlos2.pod
+	copy ..\README.os2 ..\pod\perlos2.pod
+	copy ..\vms\perlvms.pod ..\pod\perlvms.pod
+	cd ..\pod && $(MAKE) -f ..\win32\pod.mak converters
+	cd ..\lib && $(PERLEXE) lib_pm.PL
+	$(PERLEXE) $(PL2BAT) $(UTILS)
+
+distclean: clean
+	-del /f $(MINIPERL) $(PERLEXE) $(PERLDLL) $(GLOBEXE) \
+		$(PERLIMPLIB) ..\miniperl$(a) $(MINIMOD)
+	-del /f *.def *.map
+	-del /f $(EXTENSION_DLL) $(EXTENSION_PM)
+	-del /f $(EXTENSION_C) $(DYNALOADER).c $(ERRNO).pm
+	-del /f $(EXTDIR)\DynaLoader\dl_win32.xs
+	-del /f $(LIBDIR)\.exists $(LIBDIR)\attrs.pm $(LIBDIR)\DynaLoader.pm
+	-del /f $(LIBDIR)\XSLoader.pm
+	-del /f $(LIBDIR)\Fcntl.pm $(LIBDIR)\IO.pm $(LIBDIR)\Opcode.pm
+	-del /f $(LIBDIR)\ops.pm $(LIBDIR)\Safe.pm $(LIBDIR)\Thread.pm
+	-del /f $(LIBDIR)\SDBM_File.pm $(LIBDIR)\Socket.pm $(LIBDIR)\POSIX.pm
+	-del /f $(LIBDIR)\B.pm $(LIBDIR)\O.pm $(LIBDIR)\re.pm
+	-del /f $(LIBDIR)\Data\Dumper.pm $(LIBDIR)\ByteLoader.pm
+	-del /f $(LIBDIR)\Devel\Peek.pm $(LIBDIR)\Devel\DProf.pm
+	-del /f $(LIBDIR)\File\Glob.pm
+	-del /f $(LIBDIR)\Storable.pm
+	-if exist $(LIBDIR)\IO rmdir /s /q $(LIBDIR)\IO || rmdir /s $(LIBDIR)\IO
+	-if exist $(LIBDIR)\Thread rmdir /s /q $(LIBDIR)\Thread || rmdir /s $(LIBDIR)\Thread
+	-if exist $(LIBDIR)\B rmdir /s /q $(LIBDIR)\B || rmdir /s $(LIBDIR)\B
+	-if exist $(LIBDIR)\Data rmdir /s /q $(LIBDIR)\Data || rmdir /s $(LIBDIR)\Data
+	-del /f $(PODDIR)\*.html
+	-del /f $(PODDIR)\*.bat
+	-cd ..\utils && del /f h2ph splain perlbug pl2pm c2ph h2xs perldoc \
+	    dprofpp *.bat
+	-cd ..\x2p && del /f find2perl s2p *.bat
+	-del /f ..\config.sh ..\splittree.pl perlmain.c dlutils.c config.h.new
+	-del /f $(CONFIGPM)
+	-del /f bin\*.bat
+	-cd $(EXTDIR) && del /s *$(a) *.def *.map *.pdb *.bs Makefile *$(o) \
+	    pm_to_blib
+	-if exist $(AUTODIR) rmdir /s /q $(AUTODIR) || rmdir /s $(AUTODIR)
+	-if exist $(COREDIR) rmdir /s /q $(COREDIR) || rmdir /s $(COREDIR)
+
+install : all installbare installhtml
+
+installbare : $(RIGHTMAKE) utils
+	$(PERLEXE) ..\installperl
+	if exist $(WPERLEXE) $(XCOPY) $(WPERLEXE) $(INST_BIN)\*.*
+	$(XCOPY) $(GLOBEXE) $(INST_BIN)\*.*
+	$(XCOPY) bin\*.bat $(INST_SCRIPT)\*.*
+
+installhtml : doc
+	$(RCOPY) html\*.* $(INST_HTML)\*.*
+
+inst_lib : $(CONFIGPM)
+	copy splittree.pl .. 
+	$(MINIPERL) -I..\lib ..\splittree.pl "../LIB" $(AUTODIR)
+	$(RCOPY) ..\lib $(INST_LIB)\*.*
+
+minitest : $(MINIPERL) $(GLOBEXE) $(CONFIGPM) utils
+	$(XCOPY) $(MINIPERL) ..\t\perl.exe
+.IF "$(CCTYPE)" == "BORLAND"
+	$(XCOPY) $(GLOBBAT) ..\t\$(NULL)
+.ELSE
+	$(XCOPY) $(GLOBEXE) ..\t\$(NULL)
+.ENDIF
+	attrib -r ..\t\*.*
+	copy test ..\t
+	cd ..\t && \
+	$(MINIPERL) -I..\lib test base/*.t comp/*.t cmd/*.t io/*.t op/*.t pragma/*.t
+
+test-prep : all utils
+	$(XCOPY) $(PERLEXE) ..\t\$(NULL)
+	$(XCOPY) $(PERLDLL) ..\t\$(NULL)
+.IF "$(CCTYPE)" == "BORLAND"
+	$(XCOPY) $(GLOBBAT) ..\t\$(NULL)
+.ELSE
+	$(XCOPY) $(GLOBEXE) ..\t\$(NULL)
+.ENDIF
+
+test : $(RIGHTMAKE) test-prep
+	cd ..\t && $(PERLEXE) -I..\lib harness
+
+test-notty : test-prep
+	set PERL_SKIP_TTY_TEST=1 && \
+	    cd ..\t && $(PERLEXE) -I.\lib harness
+
+test-wide : test-prep
+	set HARNESS_PERL_SWITCHES=-C && \
+	    cd ..\t && $(PERLEXE) -I..\lib harness
+
+test-wide-notty : test-prep
+	set PERL_SKIP_TTY_TEST=1 && \
+	    set HARNESS_PERL_SWITCHES=-C && \
+	    cd ..\t && $(PERLEXE) -I..\lib harness
+
+clean : 
+	-@erase miniperlmain$(o)
+	-@erase $(MINIPERL)
+	-@erase perlglob$(o)
+	-@erase perlmain$(o)
+	-@erase config.w32
+	-@erase /f config.h
+	-@erase $(GLOBEXE)
+	-@erase $(PERLEXE)
+	-@erase $(WPERLEXE)
+	-@erase $(PERLDLL)
+	-@erase $(CORE_OBJ)
+	-if exist $(MINIDIR) rmdir /s /q $(MINIDIR) || rmdir /s $(MINIDIR)
+	-@erase $(WIN32_OBJ)
+	-@erase $(DLL_OBJ)
+	-@erase $(X2P_OBJ)
+	-@erase ..\*$(o) ..\*$(a) ..\*.exp *$(o) *$(a) *.exp *.res
+	-@erase ..\t\*.exe ..\t\*.dll ..\t\*.bat
+	-@erase ..\x2p\*.exe ..\x2p\*.bat
+	-@erase *.ilk
+	-@erase *.pdb
+
+# Handy way to run perlbug -ok without having to install and run the
+# installed perlbug. We don't re-run the tests here - we trust the user.
+# Please *don't* use this unless all tests pass.
+# If you want to report test failures, use "dmake nok" instead.
+ok: utils
+	$(PERLEXE) -I..\lib ..\utils\perlbug -ok -s "(UNINSTALLED)"
+
+okfile: utils
+	$(PERLEXE) -I..\lib ..\utils\perlbug -ok -s "(UNINSTALLED)" -F perl.ok
+ 
+nok: utils
+	$(PERLEXE) -I..\lib ..\utils\perlbug -nok -s "(UNINSTALLED)"
+ 
+nokfile: utils
+	$(PERLEXE) -I..\lib ..\utils\perlbug -nok -s "(UNINSTALLED)" -F perl.nok