######## This example from excerpt of :
#
# Version 11.0.1
# $Date: 2000/03/02 15:51:11 $
# terminfo syntax
#
######## ANSI, UNIX CONSOLE, AND SPECIAL TYPES
#
# This section describes terminal classes and brands that are still
# quite common.
#
#### Specials
#
# Special "terminals". These are used to label tty lines when you don't
# know what kind of terminal is on it. The characteristics of an unknown
# terminal are the lowest common denominator - they look about like a ti 700.
#
dumb|80-column dumb tty,
am,
cols#80,
bel=^G, cr=^M, cud1=^J, ind=^J,
unknown|unknown terminal type,
gn, use=dumb,
lpr|printer|line printer,
hc, os,
cols#132, lines#66,
bel=^G, cr=^M, cub1=^H, cud1=^J, ff=^L, ind=^J,
glasstty|classic glass tty interpreting ASCII control characters,
am,
cols#80,
bel=^G, clear=^L, cr=^M, cub1=^H, cud1=^J, ht=^I, kcub1=^H,
kcud1=^J, nel=^M^J,
vanilla,
bel=^G, cr=^M, cud1=^J, ind=^J,
#### ANSI.SYS/ISO 6429/ECMA-48 Capabilities
#
# See the end-of-file comment for more on these.
#
# ANSI capabilities are broken up into pieces, so that a terminal
# implementing some ANSI subset can use many of them.
ansi+local1,
cub1=\E[D, cud1=\E[B, cuf1=\E[C, cuu1=\E[A,
ansi+local,
cub=\E[%p1%dD, cud=\E[%p1%dB, cuf=\E[%p1%dC,
cuu=\E[%p1%dA,
use=ansi+local1,
ansi+tabs,
cbt=\E[Z, ht=^I, hts=\EH, tbc=\E[2g,
ansi+inittabs,
it#8, use=ansi+tabs,
ansi+erase,
clear=\E[H\E[J, ed=\E[J, el=\E[K,
ansi+rca,
hpa=\E[%p1%{1}%+%dG, vpa=\E[%p1%{1}%+%dd,
ansi+cup,
cup=\E[%i%p1%d;%p2%dH, home=\E[H,
ansi+rep,
rep=%p1%c\E[%p2%{1}%-%db,
ansi+idl1,
dl1=\E[M, il1=\E[L,
ansi+idl,
dl=\E[%p1%dM, il=\E[%p1%dL, use=ansi+idl1,
ansi+idc,
dch1=\E[P, ich=\E[%p1%d@, ich1=\E[@, rmir=\E6, smir=\E6,
ansi+arrows,
kbs=^H, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
khome=\E[H,
ansi+sgr|ansi graphic renditions,
blink=\E[5m, invis=\E[8m, rev=\E[7m, sgr0=\E[0m,
ansi+sgrso|ansi standout only,
rmso=\E[m, smso=\E[7m,
ansi+sgrul|ansi underline only,
rmul=\E[m, smul=\E[4m,
ansi+sgrbold|ansi graphic renditions; assuming terminal has bold; not dim,
bold=\E[1m,
sgr=\E[%?%p1%t7;%;%?%p2%t4;%;%?%p3%t7;%;%?%p4%t5;%;%?%p6%t1;%;m, use=ansi+sgr, use=ansi+sgrso, use=ansi+sgrul,
ansi+sgrdim|ansi graphic renditions; assuming terminal has dim; not bold,
dim=\E[2m,
sgr=\E[%?%p1%t7;%;%?%p2%t4;%;%?%p3%t7;%;%?%p4%t5;%;%?%p5%t2;%;m, use=ansi+sgr, use=ansi+sgrso, use=ansi+sgrul,
ansi+pp|ansi printer port,
mc0=\E[0i, mc4=\E[4i, mc5=\E[5i,
ansi+csr|ansi scroll-region plus cursor save & restore,
csr=\E[%i%p1%d;%p2%dr, rc=\E8, sc=\E7,
# The IBM PC alternate character set. Plug this into any Intel console entry.
# We use \E[11m for rmacs rather than \E[12m so the string can use the
# ROM graphics for control characters such as the diamond, up- and down-arrow.
# This works with the System V, Linux, and BSDI consoles. It's a safe bet this
# will work with any Intel console, they all seem to have inherited \E[11m
# from the ANSI.SYS de-facto standard.
klone+acs|alternate character set for ansi.sys displays,
acsc=+\020\,\021-\030.^Y0\333`\004a\261f\370g\361h\260j\331k\277l\332m\300n\305o~p\304q\304r\304s_t\303u\264v\301w\302x\263y\363z\362{\343|\330}\234~\376,
rmacs=\E[10m, smacs=\E[11m,
# Highlight controls corresponding to the ANSI.SYS standard. Most
# console drivers for Intel boxes obey these. Makes the same assumption
# about \E[11m as klone+acs. True ANSI/ECMA-48 would have ,
# , but this isn't a documented feature of ANSI.SYS.
klone+sgr|attribute control for ansi.sys displays,
blink=\E[5m, bold=\E[1m, invis=\E[8m, rev=\E[7m,
rmpch=\E[10m, rmso=\E[m, rmul=\E[m,
sgr=\E[0;10%?%p1%t;7%;%?%p2%t;4%;%?%p3%t;7%;%?%p4%t;5%;%?%p6%t;1%;%?%p7%t;8%;%?%p9%t;11%;m,
sgr0=\E[0;10m, smpch=\E[11m, smso=\E[7m, smul=\E[4m,
use=klone+acs,
# Highlight controls corresponding to the ANSI.SYS standard. *All*
# console drivers for Intel boxes obey these. Does not assume \E[11m will
# work; uses \E[12m instead, which is pretty bulletproof but loses you the ACS
# diamond and arrow characters under curses.
klone+sgr-dumb|attribute control for ansi.sys displays (no ESC [ 11 m),
blink=\E[5m, bold=\E[1m, invis=\E[8m, rev=\E[7m, rmso=\E[m,
rmul=\E[m,
sgr=\E[0;10%?%p1%t;7%;%?%p2%t;4%;%?%p3%t;7%;%?%p4%t;5%;%?%p6%t;1%;%?%p7%t;8%;%?%p9%t;12%;m,
sgr0=\E[0;10m, smacs=\E[12m, smso=\E[7m, smul=\E[4m,
use=klone+acs,
# KOI8-R (RFC1489) acs (alternate character set)
# From: Qing Long , 24 Feb 1996.
klone+koi8acs|alternate character set for ansi.sys displays with KOI8 charset,
acsc=+\020\,\021-\036.^_0\215`\004a\237f\234g\232h\222i\220j\205k\203l\202m\204n\212o\213p\216q\0r\217s\214t\206u\207v\210w\211x\201y\230z\231{\267|\274}L~\225,
rmacs=\E[10m, smacs=\E[11m,
# ANSI.SYS color control. The setab/setaf caps depend on the coincidence
# between SVr4/XPG4's color numbers and ANSI.SYS attributes. Here are longer
# but equivalent strings that don't rely on that coincidence:
# setb=\E[4%?%p1%{1}%=%t4%e%p1%{3}%=%t6%e%p1%{4}%=%t1%e%p1%{6}%=%t3%e%p1%d%;m,
# setf=\E[3%?%p1%{1}%=%t4%e%p1%{3}%=%t6%e%p1%{4}%=%t1%e%p1%{6}%=%t3%e%p1%d%;m,
# The DOS 5 manual asserts that these sequences meet the ISO 6429 standard.
# They match a subset of ECMA-48.
klone+color|color control for ansi.sys and ISO6429-compatible displays,
colors#8, ncv#3, pairs#64,
op=\E[37;40m, setab=\E[4%p1%dm, setaf=\E[3%p1%dm,
# This is better than klone+color, it doesn't assume white-on-black as the
# default color pair, but many `ANSI' terminals don't grok the cap.
ecma+color|color control for ECMA-48-compatible terminals,
colors#8, ncv#3, pairs#64,
op=\E[39;49m, setab=\E[4%p1%dm, setaf=\E[3%p1%dm,
# Attribute control for ECMA-48-compatible terminals
ecma+sgr|attribute capabilities for true ECMA-48 terminals,
rmso=\E[27m, rmul=\E[24m,
use=klone+sgr,
# For comparison, here are all the capabilities implied by the Intel
# Binary Compatibility Standard (level 2) that fit within terminfo.
# For more detail on this rather pathetic standard, see the comments
# near the end of this file.
ibcs2|Intel Binary Compatibility Standard prescriptions,
cbt=\E[Z, clear=\Ec, cub=\E[%p1%dD, cud=\E[%p1%dB,
cuf=\E[%p1%dC, cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA,
dch=\E[%p1%dP, dispc=\E=%p1%dg, ech=\E[%p1%dX,
hpa=\E[%i%p1%dG, hts=\EH, ich=\E[%p1%d@, il=\E[%p1%dL,
indn=\E[%p1%dS, rc=\E7, rin=\E[%p1%dT, rmam=\E[?7l, sc=\E7,
smam=\E[?7h, tbc=\E[g, vpa=\E[%i%p1%dd,
#### ANSI/ECMA-48 terminals and terminal emulators
#
# See near the end of this file for details on ANSI conformance.
# Don't mess with these entries! Lots of other entries depend on them!
#
# This section lists entries in a least-capable to most-capable order.
# if you're in doubt about what `ANSI' matches yours, try them in that
# order and back off from the first that breaks.
# ansi-mr is for ANSI terminals with ONLY relative cursor addressing
# and more than one page of memory. It uses local motions instead of
# direct cursor addressing, and makes almost no assumptions. It does
# assume auto margins, no padding and/or xon/xoff, and a 24x80 screen.
ansi-mr|mem rel cup ansi,
am, xon,
cols#80, lines#24, use=vanilla, use=ansi+erase,
use=ansi+local1,
# ansi-mini is a bare minimum ANSI terminal. This should work on anything, but
# beware of screen size problems and memory relative cursor addressing.
ansi-mini|minimum ansi standard terminal,
am, xon,
cols#80, lines#24, use=vanilla, use=ansi+cup,
use=ansi+erase,
# ansi-mtabs adds relative addressing and minimal tab support
ansi-mtabs|any ansi terminal with pessimistic assumptions,
it#8,
ht=^I, use=ansi+local1, use=ansi-mini,
# ANSI X3.64 from emory!mlhhh (Hugh Hansard) via BRL
#
# The following is an entry for the full ANSI 3.64 (1977). It lacks
# padding, but most terminals using the standard are "fast" enough
# not to require any -- even at 9600 bps. If you encounter problems,
# try including the padding specifications.
#
# Note: the :as: and :ae: specifications are not implemented here, for
# the available termcap documentation does not make clear WHICH alternate
# character set to specify. ANSI 3.64 seems to make allowances for several.
# Please make the appropriate adjustments to fit your needs -- that is
# if you will be using alternate character sets.
#
# There are very few terminals running the full ANSI 3.64 standard,
# so I could only test this entry on one verified terminal (Visual 102).
# I would appreciate the results on other terminals sent to me.
#
# Please report comments, changes, and problems to:
#
# U.S. MAIL: Hugh Hansard
# Box: 22830
# Emory University
# Atlanta, GA. 30322.
#
# USENET {akgua,msdc,sb1,sb6,gatech}!emory!mlhhh.
#
# (Added vt100 , to quiet a tic warning --esr)
ansi77|ansi 3.64 standard 1977 version,
am, mir,
cols#80, it#8, lines#24,
bel=^G, clear=\E[;H\E[2J, cr=^M, csr=\E[%i%p1%d;%p2%dr,
cub1=^H, cud1=\E[B, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu1=\E[A, dch1=\E[P, dl1=\E[M$<5*/>, ed=\E[J, el=\E[K,
home=\E[H, ht=^I, il1=\E[L$<5*/>, ind=\ED, kbs=^H,
kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kf1=\EOP,
kf2=\EOR, kf4=\EOS, khome=\E[H, nel=^M\ED, rc=\E8, ri=\EM,
rmir=\E[4l, rmso=\E[m, rmul=\E[m, sc=\E7, smir=\E[4h,
smso=\E[7m, smul=\E[4m,
# Procomm and some other ANSI emulations don't recognize all of the ANSI-
# standard capabilities. This entry deletes , , , , and
# / capabilities, forcing curses to use repetitions of ,
# , and . Also deleted and , as QModem up to
# 5.03 doesn't recognize these. Finally, we delete and , which seem
# to confuse many emulators. On the other hand, we can count on these programs
# doing //. Older versions of this entry featured
# , but now seems to be more common under
# ANSI.SYS influence.
# From: Eric S. Raymond Oct 30 1995
pcansi-m|pcansi-mono|ibm-pc terminal programs claiming to be ansi (mono mode),
am, mir, msgr,
cols#80, it#8, lines#24,
bel=^G, cbt=\E[Z, clear=\E[H\E[J, cr=^M, cub1=\E[D,
cud1=\E[B, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH, cuu1=\E[A,
dch1=\E[P, dl1=\E[M, ed=\E[J, el=\E[K, home=\E[H, ht=^I,
hts=\EH, il1=\E[L, ind=^J, kbs=^H, kcub1=\E[D, kcud1=\E[B,
kcuf1=\E[C, kcuu1=\E[A, khome=\E[H, tbc=\E[2g,
use=klone+sgr-dumb,
pcansi-25-m|pcansi25m|ibm-pc terminal programs with 25 lines (mono mode),
lines#25, use=pcansi-m,
pcansi-33-m|pcansi33m|ibm-pc terminal programs with 33 lines (mono mode),
lines#33, use=pcansi-m,
pcansi-43-m|ansi43m|ibm-pc terminal programs with 43 lines (mono mode),
lines#43, use=pcansi-m,
# The color versions. All PC emulators do color...
pcansi|ibm-pc terminal programs claiming to be ansi,
use=klone+color, use=pcansi-m,
pcansi-25|pcansi25|ibm-pc terminal programs with 25 lines,
lines#25, use=pcansi,
pcansi-33|pcansi33|ibm-pc terminal programs with 33 lines,
lines#33, use=pcansi,
pcansi-43|pcansi43|ibm-pc terminal programs with 43 lines,
lines#43, use=pcansi,
# ansi-m -- full ANSI X3.64 with ANSI.SYS-compatible attributes, no color.
# If you want pound signs rather than dollars, replace `B' with `A'
# in the , , , and capabilities.
# From: Eric S. Raymond Nov 6 1995
ansi-m|ansi-mono|ANSI X3.64-1979 terminal with ANSI.SYS compatible attributes,
mc5i,
cub=\E[%p1%dD, cud=\E[%p1%dB, cuf=\E[%p1%dC,
cuu=\E[%p1%dA, dch=\E[%p1%dP, dl=\E[%p1%dM,
ech=\E[%p1%dX, el1=\E[1K, hpa=\E[%i%p1%dG, ht=\E[I,
ich=\E[%p1%d@, il=\E[%p1%dL, indn=\E[%p1%dS, kbs=^H,
kcbt=\E[Z, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
kich1=\E[L, mc4=\E[4i, mc5=\E[5i, nel=\r\E[S,
rep=%p1%c\E[%p2%{1}%-%db, rin=\E[%p1%dT, s0ds=\E(B,
s1ds=\E)B, s2ds=\E*B, s3ds=\E+B, tbc=\E[2g,
vpa=\E[%i%p1%dd, use=pcansi-m,
# ansi -- this terminfo expresses the largest subset of X3.64 that will fit in
# standard terminfo. Assumes ANSI.SYS-compatible attributes and color.
# From: Eric S. Raymond Nov 6 1995
ansi|ansi/pc-term compatible with color,
u6=\E[%i%d;%dR, u7=\E[6n, u8=\E[?%[;0123456789]c,
u9=\E[c,
use=ecma+color, use=klone+sgr, use=ansi-m,
# ansi-generic is a vanilla ANSI terminal. This is assumed to implement
# all the normal ANSI stuff with no extensions. It assumes
# insert/delete line/char is there, so it won't work with
# vt100 clones. It assumes video attributes for bold, blink,
# underline, and reverse, which won't matter much if the terminal
# can't do some of those. Padding is assumed to be zero, which
# shouldn't hurt since xon/xoff is assumed.
ansi-generic|generic ansi standard terminal,
am, xon,
cols#80, lines#24, use=vanilla, use=ansi+csr, use=ansi+cup,
use=ansi+rca, use=ansi+erase, use=ansi+tabs,
use=ansi+local, use=ansi+idc, use=ansi+idl, use=ansi+rep,
use=ansi+sgrbold, use=ansi+arrows,
#### Linux consoles
#
# This entry is good for the 1.2.13 or later version of the Linux console.
#
# ***************************************************************************
# * *
# * WARNING: *
# * Linuxes come with a default keyboard mapping kcbt=^I. This entry, in *
# * response to user requests, assumes kcbt=\E[Z, the ANSI/ECMA reverse-tab *
# * character. Here are the keymap replacement lines that will set this up: *
# * *
# keycode 15 = Tab Tab
# alt keycode 15 = Meta_Tab
# shift keycode 15 = F26
# string F26 ="\033[Z"
# * *
# * This has to use a key slot which is unfortunate (any unused one will *
# * do, F26 is the higher-numbered one). The change ought to be built *
# * into the kernel tables. *
# * *
# ***************************************************************************
#
# The 1.3.x kernels add color-change capabilities; if yours doesn't have this
# and it matters, turn off . The %02x escape used to implement this is
# not back-portable to SV curses and not supported in ncurses versions before
# 1.9.9. All linux kernels since 1.2.13 (at least) set the screen size
# themselves; this entry assumes that capability.
#
# This entry is good for the 1.2.13 or later version of the Linux console.
#
# ***************************************************************************
# * *
# * WARNING: *
# * Linuxes come with a default keyboard mapping kcbt=^I. This entry, in *
# * response to user requests, assumes kcbt=\E[Z, the ANSI/ECMA reverse-tab *
# * character. Here are the keymap replacement lines that will set this up: *
# * *
# keycode 15 = Tab Tab
# alt keycode 15 = Meta_Tab
# shift keycode 15 = F26
# string F26 ="\033[Z"
# * *
# * This has to use a key slot which is unfortunate (any unused one will *
# * do, F26 is the higher-numbered one). The change ought to be built *
# * into the kernel tables. *
# * *
# ***************************************************************************
#
# The 1.3.x kernels add color-change capabilities; if yours doesn't have this
# and it matters, turn off . The %02x escape used to implement this is
# not back-portable to SV curses and not supported in ncurses versions before
# 1.9.9. All linux kernels since 1.2.13 (at least) set the screen size
# themselves; this entry assumes that capability.
#
# The 2.2.x kernels add a private mode that sets the cursor type; use that to
# get a block cursor for cvvis.
# reported by Frank Heckenbach .
linux|linux console,
am, bce, eo, mir, msgr, xenl, xon,
it#8, ncv#2,
acsc=+\020\,\021-\030.^Y0\333`\004a\261f\370g\361h\260i\316j\331k\277l\332m\300n\305o~p\304q\304r\304s_t\303u\264v\301w\302x\263y\363z\362{\343|\330}\234~\376,
bel=^G, civis=\E[?25l\E[?1c, clear=\E[H\E[J,
cnorm=\E[?25h\E[?0c, cr=^M, csr=\E[%i%p1%d;%p2%dr,
cub1=^H, cud1=^J, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu1=\E[A, cvvis=\E[?25h\E[?8c, dch=\E[%p1%dP, dch1=\E[P,
dim=\E[2m, dl=\E[%p1%dM, dl1=\E[M, ech=\E[%p1%dX, ed=\E[J,
el=\E[K, el1=\E[1K, flash=\E[?5h\E[?5l$<200/>, home=\E[H,
hpa=\E[%i%p1%dG, ht=^I, hts=\EH, ich=\E[%p1%d@, ich1=\E[@,
il=\E[%p1%dL, il1=\E[L, ind=^J, kb2=\E[G, kbs=\177,
kcbt=\E[Z, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
kdch1=\E[3~, kend=\E[4~, kf1=\E[[A, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf13=\E[25~, kf14=\E[26~,
kf15=\E[28~, kf16=\E[29~, kf17=\E[31~, kf18=\E[32~,
kf19=\E[33~, kf2=\E[[B, kf20=\E[34~, kf3=\E[[C, kf4=\E[[D,
kf5=\E[[E, kf6=\E[17~, kf7=\E[18~, kf8=\E[19~, kf9=\E[20~,
khome=\E[1~, kich1=\E[2~, knp=\E[6~, kpp=\E[5~, kspd=^Z,
nel=^M^J, rc=\E8, rev=\E[7m, ri=\EM, rmir=\E[4l, rmso=\E[27m,
rmul=\E[24m, rs1=\Ec\E]R, sc=\E7,
sgr=\E[0;10%?%p1%t;7%;%?%p2%t;4%;%?%p3%t;7%;%?%p4%t;5%;%?%p5%t;2%;%?%p6%t;1%;%?%p7%t;8%;%?%p9%t;11%;m,
smir=\E[4h, smul=\E[4m, tbc=\E[3g, u6=\E[%i%d;%dR,
u7=\E[6n, u8=\E[?6c, u9=\E[c, vpa=\E[%i%p1%dd,
use=klone+sgr, use=ecma+color,
linux-m|Linux console no color,
colors@, pairs@,
setab@, setaf@, setb@, setf@, use=linux,
linux-c-nc|linux console 1.3.x hack for ncurses only,
ccc,
initc=\E]P%p1%x%p2%{255}%*%{1000}%/%02x%p3%{255}%*%{1000}%/%02x%p4%{255}%*%{1000}%/%02x,
oc=\E]R,
use=linux,
# From: Dennis Henriksen , 9 July 1996
linux-c|linux console 1.3.6+ with private palette for each virtual console,
ccc,
colors#8, pairs#64,
initc=\E]P%?%p1%{9}%>%t%p1%{10}%-%'a'%+%c%e%p1%d%;%p2%{255}%&%Pr%gr%{16}%/%Px%?%gx%{9}%>%t%gx%{10}%-%'A'%+%c%e%gx%d%;%gr%{15}%&%Px%?%gx%{9}%>%t%gx%{10}%-%'A'%+%c%e%gx%d%;%p3%{255}%&%Pr%gr%{16}%/%Px%?%gx%{9}%>%t%gx%{10}%-%'A'%+%c%e%gx%d%;%gr%{15}%&%Px%?%gx%{9}%>%t%gx%{10}%-%'A'%+%c%e%gx%d%;%p4%{255}%&%Pr%gr%{16}%/%Px%?%gx%{9}%>%t%gx%{10}%-%'A'%+%c%e%gx%d%;%gr%{15}%&%Px%?%gx%{9}%>%t%gx%{10}%-%'A'%+%c%e%gx%d%;,
oc=\E]R,
use=linux,
# See the note on ICH/ICH1 VERSUS RMIR/SMIR near the end of file
linux-nic|linux with ich/ich1 suppressed for non-curses programs,
ich@, ich1@,
use=linux,
# This assumes you have used setfont(8) to load one of the Linux koi8-r fonts.
# acsc entry from Pavel Roskin" , 29 Sep 1997.
linux-koi8|linux with koi8 alternate character set,
acsc=+\020\,\021-\030.^Y0\215`\004a\221f\234g\237h\220i\276j\205k\203l\202m\204n\212o~p\0q\0r\0s_t\206u\207v\211w\210x\201y\230z\231{\267|\274~\224,
use=linux, use=klone+koi8acs,
# Another entry for KOI8-r with Qing Long's acsc.
# (which one better complies with the standard?)
linux-koi8r|linux with koi8-r alternate character set,
use=linux, use=klone+koi8acs,
# Entry for the latin1 and latin2 fonts
linux-lat|linux with latin1 or latin2 alternate character set,
acsc=+\020\,\021-\030.^Y0\333`\004a\013f\370g\361h\260i\316j\211k\214l\206m\203n\305o~p\304q\212r\304s_t\207u\215v\301w\302x\205y\363z\362{\343|\330}\234~\376,
use=linux,
#### NetBSD consoles
#
# pcvt termcap database entries (corresponding to release 3.31)
# Author's last edit-date: [Fri Sep 15 20:29:10 1995]
#
# (For the terminfo master file, I translated these into terminfo syntax.
# Then I dropped all the pseudo-HP entries. we don't want and can't use
# the :Xs: flag. Then I split :is: into a size-independent and a
# size-dependent . Finally, I added / -- esr)
# NOTE: has been taken out of this entry. for reference, it should
# be . For discussion, see ICH/ICH1 VERSUS RMIR/SMIR below.
# (esr: added and to resolve NetBSD Problem Report #4583)
pcvtXX|pcvt vt200 emulator (DEC VT220),
am, km, mir, msgr, xenl,
it#8, vt#3,
acsc=++\,\,--..00``aaffgghhiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz~~,
bel=^G, blink=\E[5m, bold=\E[1m, civis=\E[?25l,
clear=\E[H\E[J, cnorm=\E[?25h, cr=^M,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
el=\E[K, el1=\E[1K, home=\E[H, ht=^I, hts=\EH, ich=\E[%p1%d@,
il=\E[%p1%dL, il1=\E[L, ind=\ED, indn=\E[%p1%dS,
is1=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, kbs=\177,
kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kdch1=\E[3~, kf1=\E[17~, kf2=\E[18~, kf3=\E[19~,
kf4=\E[20~, kf5=\E[21~, kf6=\E[23~, kf7=\E[24~, kf8=\E[25~,
khome=\E[1~, kich1=\E[2~, kll=\E[4~, knp=\E[6~, kpp=\E[5~,
nel=\EE, rc=\E8, rev=\E[7m, rf=/usr/share/tabset/vt100,
ri=\EM, rin=\E[%p1%dT, rmacs=\E(B, rmam=\E[?7l, rmir=\E[4l,
rmkx=\E[?1l\E>, rmso=\E[27m, rmul=\E[24m,
rs1=\Ec\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, sc=\E7,
sgr0=\E[m, smacs=\E(0, smam=\E[?7h, smir=\E[4h,
smkx=\E[?1h\E=, smso=\E[7m, smul=\E[4m, tbc=\E[3g,
# NetBSD/FreeBSD vt220 terminal emulator console (pc keyboard & monitor)
# termcap entries for pure VT220-Emulation and 25, 28, 35, 40, 43 and
# 50 lines entries; 80 columns
pcvt25|dec vt220 emulation with 25 lines,
cols#80, lines#25,
is2=\E[1;25r\E[25;1H, use=pcvtXX,
pcvt28|dec vt220 emulation with 28 lines,
cols#80, lines#28,
is2=\E[1;28r\E[28;1H, use=pcvtXX,
pcvt35|dec vt220 emulation with 35 lines,
cols#80, lines#35,
is2=\E[1;35r\E[35;1H, use=pcvtXX,
pcvt40|dec vt220 emulation with 40 lines,
cols#80, lines#40,
is2=\E[1;40r\E[40;1H, use=pcvtXX,
pcvt43|dec vt220 emulation with 43 lines,
cols#80, lines#43,
is2=\E[1;43r\E[43;1H, use=pcvtXX,
pcvt50|dec vt220 emulation with 50 lines,
cols#80, lines#50,
is2=\E[1;50r\E[50;1H, use=pcvtXX,
# NetBSD/FreeBSD vt220 terminal emulator console (pc keyboard & monitor)
# termcap entries for pure VT220-Emulation and 25, 28, 35, 40, 43 and
# 50 lines entries; 132 columns
pcvt25w|dec vt220 emulation with 25 lines and 132 cols,
cols#132, lines#25,
is2=\E[1;25r\E[25;1H, use=pcvtXX,
pcvt28w|dec vt220 emulation with 28 lines and 132 cols,
cols#132, lines#28,
is2=\E[1;28r\E[28;1H, use=pcvtXX,
pcvt35w|dec vt220 emulation with 35 lines and 132 cols,
cols#132, lines#35,
is2=\E[1;35r\E[35;1H, use=pcvtXX,
pcvt40w|dec vt220 emulation with 40 lines and 132 cols,
cols#132, lines#40,
is2=\E[1;40r\E[40;1H, use=pcvtXX,
pcvt43w|dec vt220 emulation with 43 lines and 132 cols,
cols#132, lines#43,
is2=\E[1;43r\E[43;1H, use=pcvtXX,
pcvt50w|dec vt220 emulation with 50 lines and 132 cols,
cols#132, lines#50,
is2=\E[1;50r\E[50;1H, use=pcvtXX,
# Terminfo entries to enable the use of the ncurses library in colour on a
# NetBSD-arm32 console (only tested on a RiscPC).
# Created by Dave Millen 22.07.98
# modified codes for setf/setb to setaf/setab, then to klone+color, corrected
# typo in invis - TD
arm100|arm100-am|Arm(RiscPC) ncurses compatible (for 640x480),
am, bce, msgr, xenl, xon,
cols#80, it#8, lines#30,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m$<2>, bold=\E[1m$<2>,
clear=\E[H\E[J$<50>, cr=^M, csr=\E[%i%p1%d;%p2%dr,
cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=^J,
cuf=\E[%p1%dC, cuf1=\E[C$<2>,
cup=\E[%i%p1%d;%p2%dH$<5>, cuu=\E[%p1%dA,
cuu1=\E[A$<2>, ed=\E[J$<50>, el=\E[K$<3>, el1=\E[1K$<3>,
enacs=\E(B\E)0, home=\E[H, ht=^I, hts=\EH, ind=^J,
invis=\E[8m$<2>, ka1=\E[q, ka3=\E[s, kb2=\E[r, kbs=^H,
kc1=\E[p, kc3=\E[n, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C,
kcuu1=\E[A, kent=\E[M, kf0=\E[y, kf1=\E[P, kf10=\E[x,
kf2=\E[Q, kf3=\E[R, kf4=\E[S, kf5=\E[t, kf6=\E[u, kf7=\E[v,
kf8=\E[l, kf9=\E[w, rc=\E8, rev=\E[6m$<2>, ri=\EM$<5>,
rmacs=^O, rmam=\E[?7l, rmkx=\E[?1l\E>, rmso=\E[m$<2>,
rmul=\E[m$<2>, rs2=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h,
sc=\E7,
sgr=\E[0%?%p1%p6%|%t;1%;%?%p2%t;4%;%?%p1%p3%|%t;7%;%?%p4%t;5%;m%?%p9%t\016%e\017%;,
sgr0=\E[m\017$<2>, smacs=^N, smam=\E[?7h, smkx=\E[?1h\E=,
smso=\E[7m$<2>, smul=\E[4m$<2>, tbc=\E[3g,
use=ecma+sgr, use=klone+color,
arm100-w|arm100-wam|Arm(RiscPC) ncurses compatible (for 1024x768),
cols#132, lines#50, use=arm100,
# NetBSD/x68k console vt200 emulator. This port runs on a 68K machine
# manufactured by Sharp for the Japenese market.
# From Minoura Makoto , 12 May 1996
x68k|x68k-ite|NetBSD/x68k ITE,
cols#96, lines#32,
kclr=\E[9~, khlp=\E[28~, use=vt220,
# :
# Entry for the DNARD OpenFirmware console, close to ANSI but not quite.
#
# (still unfinished, but good enough so far.)
ofcons,
bw,
cols#80, lines#30,
bel=^G, blink=\2337;2m, bold=\2331m, clear=^L, cr=^M,
cub=\233%p1%dD, cub1=\233D, cud=\233%p1%dB, cud1=\233B,
cuf=\233%p1%dC, cuf1=\233C, cup=\233%i%p1%d;%p2%dH,
cuu=\233%p1%dA, cuu1=\233A, dch=\233%p1%dP, dch1=\233P,
dim=\2332m, dl=\233%p1%dM, dl1=\233M, ed=\233J, el=\233K,
flash=^G, ht=^I, ich=\233%p1%d@, ich1=\233@, il=\233%p1%dL,
il1=\233L, ind=^J, invis=\2338m, kbs=^H, kcub1=\233D,
kcud1=\233B, kcuf1=\233C, kcuu1=\233A, kdch1=\233P,
kf1=\2330P, kf10=\2330M, kf2=\2330Q, kf3=\2330W,
kf4=\2330x, kf5=\2330t, kf6=\2330u, kf7=\2330q, kf8=\2330r,
kf9=\2330p, knp=\233/, kpp=\233?, nel=^M^J, rev=\2337m,
rmso=\2330m, rmul=\2330m, sgr0=\2330m,
# NetBSD "wscons" emulator in vt220 mode
# These are micro-minimal and probably need to be redone for real
# after the manner of the pcvt entries.
wsvt25|NetBSD wscons in 25 line DEC VT220 mode,
cols#80, lines#25, use=vt220,
wsvt25m|NetBSD wscons in 25 line DEC VT220 mode with Meta,
km,
cols#80, lines#25, use=vt220,
# `rasterconsole' provided by 4.4BSD, NetBSD and OpenBSD on SPARC, and
# DECstation/pmax.
rcons|BSD rasterconsole,
use=sun-il,
# Color version of above. Color currenly only provided by NetBSD.
rcons-color|BSD rasterconsole with ANSI color,
bce,
colors#8, pairs#64,
op=\E[m, setab=\E[4%dm, setaf=\E[3%dm, use=rcons,
#### FreeBSD console entries
#
# From: Andrey Chernov 29 Mar 1996
# Andrey Chernov maintains the FreeBSD termcap distributions.
#
# Note: Users of FreeBSD 2.1.0 and older versions must either upgrade
# or comment out the :cb: capability in the console entry.
#
# Alexander Lukyanov reports:
# I have seen FreeBSD-2.1.5R... The old el1 bug changed, but it is still there.
# Now el1 clears not only to the line beginning, but also a large chunk
# of previous line. But there is another bug - ech does not work at all.
#
# for syscons
# common entry without semigraphics
# Bug: The capability resets attributes.
# Bug? The ech and el1 attributes appear to move the cursor in some cases; for
# instance el1 does if the cursor is moved to the right margin first. Removed
# by T.Dickey 97/5/3 (ech=\E[%p1%dX, el1=\E[1K)
#
# Setting colors turns off reverse; we cannot guarantee order, so use ncv.
# Note that this disables standout with color.
cons25w|ansiw|ansi80x25-raw|freebsd console (25-line raw mode),
am, bce, bw, eo, msgr, npc,
colors#8, cols#80, it#8, lines#25, ncv#21, pairs#64,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z, clear=\E[H\E[J,
cnorm=\E[=0C, cr=^M, cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB,
cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
cvvis=\E[=1C, dch=\E[%p1%dP, dch1=\E[P, dim=\E[30;1m,
dl=\E[%p1%dM, dl1=\E[M, ed=\E[J, el=\E[K, home=\E[H,
hpa=\E[%i%p1%d`, ht=^I, ich=\E[%p1%d@, ich1=\E[@,
il=\E[%p1%dL, il1=\E[L, ind=\E[S, indn=\E[%p1%dS, kb2=\E[E,
kbs=^H, kcbt=\E[Z, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C,
kcuu1=\E[A, kdch1=\177, kend=\E[F, kf1=\E[M, kf10=\E[V,
kf11=\E[W, kf12=\E[X, kf2=\E[N, kf3=\E[O, kf4=\E[P, kf5=\E[Q,
kf6=\E[R, kf7=\E[S, kf8=\E[T, kf9=\E[U, khome=\E[H,
kich1=\E[L, knp=\E[G, kpp=\E[I, nel=\E[E, op=\E[x, rev=\E[7m,
ri=\E[T, rin=\E[%p1%dT, rmso=\E[m, rs1=\E[x\E[m\Ec,
setab=\E[4%p1%dm, setaf=\E[3%p1%dm, sgr0=\E[m,
smso=\E[7m, vpa=\E[%i%p1%dd,
cons25|ansis|ansi80x25|freebsd console (25-line ansi mode),
acsc=-\030.^Y0\333`\004a\260f\370g\361h\261i\025j\331k\277l\332m\300n\305q\304t\303u\264v\301w\302x\263y\363z\362~\371,
use=cons25w,
cons25-m|ansis-mono|ansi80x25-mono|freebsd console (25-line mono ansi mode),
colors@, pairs@,
bold@, dim@, op@, rmul=\E[m, setab@, setaf@, smul=\E[4m, use=cons25,
cons30|ansi80x30|freebsd console (30-line ansi mode),
lines#30, use=cons25,
cons30-m|ansi80x30-mono|freebsd console (30-line mono ansi mode),
lines#30, use=cons25-m,
cons43|ansi80x43|freebsd console (43-line ansi mode),
lines#43, use=cons25,
cons43-m|ansi80x43-mono|freebsd console (43-line mono ansi mode),
lines#43, use=cons25-m,
cons50|ansil|ansi80x50|freebsd console (50-line ansi mode),
lines#50, use=cons25,
cons50-m|ansil-mono|ansi80x50-mono|freebsd console (50-line mono ansi mode),
lines#50, use=cons25-m,
cons60|ansi80x60|freebsd console (60-line ansi mode),
lines#60, use=cons25,
cons60-m|ansi80x60-mono|freebsd console (60-line mono ansi mode),
lines#60, use=cons25-m,
cons25r|pc3r|ibmpc3r|cons25-koi8-r|freebsd console w/koi8-r cyrillic,
acsc=-\030.^Y0\215`\004a\220f\234h\221i\025j\205k\203l\202m\204n\212q\0t\206u\207v\211w\210x\201y\230z\231~\225,
use=cons25w,
cons25r-m|pc3r-m|ibmpc3r-mono|cons25-koi8r-m|freebsd console w/koi8-r cyrillic (mono),
colors@, pairs@,
op@, rmul=\E[m, setab@, setaf@, smul=\E[4m, use=cons25r,
cons50r|cons50-koi8r|freebsd console w/koi8-r cyrillic (50 lines),
lines#50, use=cons25r,
cons50r-m|cons50-koi8r-m|freebsd console w/koi8-r cyrillic (50-line mono),
lines#50, use=cons25r-m,
cons60r|cons60-koi8r|freebsd console w/koi8-r cyrillic (60 lines),
lines#60, use=cons25r,
cons60r-m|cons60-koi8r-m|freebsd console w/koi8-r cyrillic (60-line mono),
lines#60, use=cons25r-m,
# ISO 8859-1 FreeBSD console
cons25l1|cons25-iso8859|freebsd console w/iso 8859-1 chars,
acsc=+\253\,\273-\030.\031`\201a\202f\207g\210i\247j\213k\214l\215m\216n\217o\220p\221q\222r\223s\224t\225u\226v\227w\230x\231y\232z\233~\237,
use=cons25w,
cons25l1-m|cons25-iso-m|freebsd console w/iso 8859-1 chars (mono),
colors@, pairs@,
bold@, dim@, op@, rmul=\E[m, setab@, setaf@, smul=\E[4m, use=cons25l1,
cons50l1|cons50-iso8859|freebsd console w/iso 8859-1 chars (50 lines),
lines#50, use=cons25l1,
cons50l1-m|cons50-iso-m|freebsd console w/iso 8859-1 chars (50-line mono),
lines#50, use=cons25l1-m,
cons60l1|cons60-iso|freebsd console w/iso 8859-1 chars (60 lines),
lines#60, use=cons25l1,
cons60l1-m|cons60-iso-m|freebsd console w/iso 8859-1 chars (60-line mono),
lines#60, use=cons25l1-m,
#### 386BSD and BSD/OS Consoles
#
# This was the original 386BSD console entry (I think).
# Some places it's named oldpc3|oldibmpc3.
# From: Alex R.N. Wetmore
origpc3|origibmpc3|IBM PC 386BSD Console,
am, bw, eo, xon,
cols#80, lines#25,
acsc=j\331k\277l\332m\300n\305q\304t\303u\264v\301w\302x\263,
bold=\E[7m, clear=\Ec, cub1=^H, cud1=\E[B, cuf1=\E[C,
cup=\E[%i%p1%2d;%p2%2dH, cuu1=\E[A, ed=\E[J, el=\E[K,
home=\E[H, ind=\E[S, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C,
kcuu1=\E[A, khome=\E[Y, ri=\E[T, rmso=\E[1;0x\E[2;7x,
rmul=\E[1;0x\E[2;7x, sgr0=\E[m\E[1;0x\E[2;7x,
smso=\E[1;7x\E[2;0x, smul=\E[1;7x\E[2;0x,
# description of BSD/386 console emulator in version 1.0 (supplied by BSDI)
oldpc3|oldibmpc3|old IBM PC BSD/386 Console,
km,
lines#25,
bel=^G, bold=\E[=15F, cr=^M, cud1=^J, dim=\E[=8F, dl1=\E[M,
ht=^I, il1=\E[L, ind=^J, kbs=^H, kcub1=\E[D, kcud1=\E[B,
kcuf1=\E[C, kcuu1=\E[A, khome=\E[H, kich1=\E[L, kll=\E[F,
knp=\E[G, kpp=\E[I, nel=^M^J, sgr0=\E[=R,
# Description of BSD/OS console emulator in version 1.1, 2.0, 2.1
# Note, the emulator supports many of the additional console features
# listed in the iBCS2 (e.g. character-set selection) though not all
# are described here. This entry really ought to be upgraded.
# Also note, the console will also work with fewer lines after doing
# "stty rows NN", e.g. to use 24 lines.
# (Color support from Kevin Rosenberg , 2 May 1996)
# Bug: The capability resets attributes.
bsdos-pc-nobold|BSD/OS PC console w/o bold,
am, eo, km, xon,
cols#80, it#8, lines#25,
bel=^G, clear=\Ec, cr=^M, cub=\E[%p1%dD, cub1=^H,
cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dl=\E[%p1%dM, dl1=\E[M, ed=\E[J, el=\E[K, home=\E[H, ht=^I,
il=\E[%p1%dL, il1=\E[L, ind=^J, kbs=^H, kcub1=\E[D,
kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, khome=\E[H, kich1=\E[L,
kll=\E[F, knp=\E[G, kpp=\E[I, nel=^M^J, rc=\E8, sc=\E7,
sgr=\E[0;10%?%p1%t;7%;%?%p3%t;7%;%?%p4%t;5%;%?%p6%t;1%;%?%p7%t;8%;%?%p9%t;11%;m%?%p5%t\E[=8F%;,
use=klone+sgr, use=klone+color,
bsdos-pc|IBM PC BSD/OS Console,
sgr=\E[0;10%?%p1%t;7%;%?%p2%t;1%;%?%p3%t;7%;%?%p4%t;5%;%?%p6%t;1%;%?%p7%t;8%;%?%p9%t;11%;m, use=bsdos-pc-nobold,
# Old names for BSD/OS PC console used in releases before 4.1.
pc3|BSD/OS on the PC Console,
use=bsdos-pc-nobold,
ibmpc3|pc3-bold|BSD/OS on the PC Console with bold instead of underline,
use=bsdos-pc,
# BSD/OS on the SPARC
bsdos-sparc|Sun SPARC BSD/OS Console,
use=sun,
# BSD/OS on the PowerPC
bsdos-ppc|PowerPC BSD/OS Console,
use=bsdos-pc,
#### DEC VT100 and compatibles
#
# DEC terminals from the vt100 forward are collected here. Older DEC terminals
# and micro consoles can be found in the `obsolete' section. More details on
# the relationship between the VT100 and ANSI X3.64/ISO 6429/ECMA-48 may be
# found near the end of this file.
#
# Except where noted, these entries are DEC's official terminfos.
# Contact Bill Hedberg of Terminal Support
# Engineering for more information. Updated terminfos and termcaps
# are kept available at ftp://gatekeeper.dec.com/pub/DEC/termcaps.
#
# In October 1995 DEC sold its terminals business, including the VT and Dorio
# line and trademark, to SunRiver Data Systems. SunRiver has since changed
# its name to Boundless Technologies; see http://www.boundless.com.
#
# NOTE: Any VT100 emulation, whether in hardware or software, almost
# certainly includes what DEC called the `Level 1 editing extension' codes;
# only the very oldest VT100s lacked these and there probably aren't any of
# those left alive. To capture these, use one of the VT102 entries.
#
# Note that the glitch in vt100 is not quite the same as on the Concept,
# since the cursor is left in a different position while in the
# weird state (concept at beginning of next line, vt100 at end
# of this line) so all versions of vi before 3.7 don't handle
# right on vt100. The correct way to handle is when
# you output the char in column 80, immediately output CR LF
# and then assume you are in column 1 of the next line. If
# is on, am should be on too.
#
# I assume you have smooth scroll off or are at a slow enough baud
# rate that it doesn't matter (1200? or less). Also this assumes
# that you set auto-nl to "on", if you set it off use vt100-nam
# below.
#
# The padding requirements listed here are guesses. It is strongly
# recommended that xon/xoff be enabled, as this is assumed here.
#
# The vt100 uses and rather than // because the
# tab settings are in non-volatile memory and don't need to be
# reset upon login. Also setting the number of columns glitches
# the screen annoyingly. You can type "reset" to get them set.
#
# The VT100 series terminals have cursor ("arrows") keys which can operate
# in two different modes: Cursor Mode and Application Mode. Cursor Mode
# is the reset state, and is assumed to be the normal state. Application
# Mode is the "set" state. In Cursor Mode, the cursor keys transmit
# "Esc [ {code}" sequences, conforming to ANSI standards. In Application
# Mode, the cursor keys transmit "Esc O " sequences. Application Mode
# was provided primarily as an aid to the porting of VT52 applications. It is
# assumed that the cursor keys are normally in Cursor Mode, and expected that
# applications such as vi will always transmit the string. Therefore,
# the definitions for the cursor keys are made to match what the terminal
# transmits after the string is transmitted. If the string
# is a null string or is not defined, then cursor keys are assumed to be in
# "Cursor Mode", and the cursor keys definitions should match that assumption,
# else the appication may fail. It is also expected that applications will
# always transmit the string to the terminal before they exit.
#
# The VT100 series terminals have an auxilliary keypad, commonly referred to as
# the "Numeric Keypad", because it is a cluster of numeric and function keys.
# The Numeric Keypad which can operate in two different modes: Numeric Mode and
# Application Mode. Numeric Mode is the reset state, and is assumed to be
# the normal state. Application Mode is the "set" state. In Numeric Mode,
# the numeric and punctuation keys transmit ASCII 7-bit characters, and the
# Enter key transmits the same as the Return key (Note: the Return key
# can be configured to send either LF (\015) or CR LF). In Application Mode,
# all the keypad keys transmit "Esc O {code}" sequences. The PF1 - PF4 keys
# always send the same "Esc O {code}" sequences. It is assumed that the keypad
# is normally in Numeric Mode. If an application requires that the keypad be
# in Application Mode then it is expected that the user, or the application,
# will set the TERM environment variable to point to a terminfo entry which has
# defined the string to include the codes that switch the keypad into
# Application Mode, and the terminfo entry will also define function key
# fields to match the Application Mode control codes. If the string
# is a null string or is not defined, then the keypad is assumed to be in
# Numeric Mode. If the string switches the keypad into Application
# Mode, it is expected that the string will contain the control codes
# necessary to reset the keypad to "Normal" mode, and it is also expected that
# applications which transmit the string will also always transmit the
# string to the terminal before they exit.
#
# Here's a diagram of the VT100 keypad keys with their bindings.
# The top line is the name of the key (some DEC keyboards have the keys
# labelled somewhat differently, like GOLD instead of PF1, but this is
# the most "official" name). The second line is the escape sequence it
# generates in Application Keypad mode (where "$" means the ESC
# character). The third line contains two items, first the mapping of
# the key in terminfo, and then in termcap.
# _______________________________________
# | PF1 | PF2 | PF3 | PF4 |
# | $OP | $OQ | $OR | $OS |
# |_kf1__k1_|_kf2__k2_|_kf3__k3_|_kf4__k4_|
# | 7 8 9 - |
# | $Ow | $Ox | $Oy | $Om |
# |_kf9__k9_|_kf10_k;_|_kf0__k0_|_________|
# | 4 | 5 | 6 | , |
# | $Ot | $Ou | $Ov | $Ol |
# |_kf5__k5_|_kf6__k6_|_kf7__k7_|_kf8__k8_|
# | 1 | 2 | 3 | |
# | $Oq | $Or | $Os | enter |
# |_ka1__K1_|_kb2__K2_|_ka3__K3_| $OM |
# | 0 | . | |
# | $Op | $On | |
# |___kc1_______K4____|_kc3__K5_|_kent_@8_|
#
# And here, for those of you with orphaned VT100s lacking documentation, is
# a description of the soft switches invoked when you do `Set Up'.
#
# Scroll 0-Jump Shifted 3 0-#
# | 1-Smooth | 1-British pound sign
# | Autorepeat 0-Off | Wrap Around 0-Off
# | | 1-On | | 1-On
# | | Screen 0-Dark Bkg | | New Line 0-Off
# | | | 1-Light Bkg | | | 1-On
# | | | Cursor 0-Underline | | | Interlace 0-Off
# | | | | 1-Block | | | | 1-On
# | | | | | | | |
# 1 1 0 1 1 1 1 1 0 1 0 0 0 0 1 0 <--Standard Settings
# | | | | | | | |
# | | | Auto XON/XOFF 0-Off | | | Power 0-60 Hz
# | | | 1-On | | | 1-50 Hz
# | | Ansi/VT52 0-VT52 | | Bits Per Char. 0-7 Bits
# | | 1-ANSI | | 1-8 Bits
# | Keyclick 0-Off | Parity 0-Off
# | 1-On | 1-On
# Margin Bell 0-Off Parity Sense 0-Odd
# 1-On 1-Even
#
# The following SET-UP modes are assumed for normal operation:
# ANSI_MODE AUTO_XON/XOFF_ON NEWLINE_OFF 80_COLUMNS
# WRAP_AROUND_ON JUMP_SCROLL_OFF
# Other SET-UP modes may be set for operator convenience or communication
# requirements; I recommend
# AUTOREPEAT_ON BLOCK_CURSOR MARGIN_BELL_OFF SHIFTED_3_#
# Unless you have a graphics add-on such as Digital Engineering's VT640
# (and even then, whenever it can be arranged!) you should set
# INTERLACE_OFF
#
# (vt100: I added / based on the init string, also . -- esr)
vt100|vt100-am|dec vt100 (w/advanced video),
am, msgr, xenl, xon,
cols#80, it#8, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m$<2>, bold=\E[1m$<2>,
clear=\E[H\E[J$<50>, cr=^M, csr=\E[%i%p1%d;%p2%dr,
cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=^J,
cuf=\E[%p1%dC, cuf1=\E[C$<2>,
cup=\E[%i%p1%d;%p2%dH$<5>, cuu=\E[%p1%dA,
cuu1=\E[A$<2>, ed=\E[J$<50>, el=\E[K$<3>, el1=\E[1K$<3>,
enacs=\E(B\E)0, home=\E[H, ht=^I, hts=\EH, ind=^J, ka1=\EOq,
ka3=\EOs, kb2=\EOr, kbs=^H, kc1=\EOp, kc3=\EOn, kcub1=\EOD,
kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, kent=\EOM, kf0=\EOy,
kf1=\EOP, kf10=\EOx, kf2=\EOQ, kf3=\EOR, kf4=\EOS, kf5=\EOt,
kf6=\EOu, kf7=\EOv, kf8=\EOl, kf9=\EOw, rc=\E8,
rev=\E[7m$<2>, ri=\EM$<5>, rmacs=^O, rmam=\E[?7l,
rmkx=\E[?1l\E>, rmso=\E[m$<2>, rmul=\E[m$<2>,
rs2=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, sc=\E7,
sgr=\E[0%?%p1%p6%|%t;1%;%?%p2%t;4%;%?%p1%p3%|%t;7%;%?%p4%t;5%;m%?%p9%t\016%e\017%;,
sgr0=\E[m\017$<2>, smacs=^N, smam=\E[?7h, smkx=\E[?1h\E=,
smso=\E[7m$<2>, smul=\E[4m$<2>, tbc=\E[3g,
vt100nam|vt100-nam|vt100 no automargins,
am@, xenl@, use=vt100-am,
vt100-vb|dec vt100 (w/advanced video) & no beep,
bel@, flash=\E[?5h\E[?5l, use=vt100,
# Ordinary vt100 in 132 column ("wide") mode.
vt100-w|vt100-w-am|dec vt100 132 cols (w/advanced video),
cols#132, lines#24,
rs2=\E>\E[?3h\E[?4l\E[?5l\E[?8h, use=vt100-am,
vt100-w-nam|vt100-nam-w|dec vt100 132 cols (w/advanced video no automargin),
cols#132, lines#14, vt@,
rs2=\E>\E[?3h\E[?4l\E[?5l\E[?8h, use=vt100-nam,
# vt100 with no advanced video.
vt100-nav|vt100 without advanced video option,
xmc#1,
blink@, bold@, rev@, rmso=\E[m, rmul@, sgr@, sgr0@, smso=\E[7m,
smul@,
use=vt100,
vt100-nav-w|vt100-w-nav|dec vt100 132 cols 14 lines (no advanced video option),
cols#132, lines#14, use=vt100-nav,
# vt100 with one of the 24 lines used as a status line.
# We put the status line on the top.
vt100-s|vt100-s-top|vt100-top-s|vt100 for use with top sysline,
eslok, hs,
lines#23,
clear=\E[2;1H\E[J$<50>, csr=\E[%i%i%p1%d;%p2%dr,
cup=\E[%i%p1%{1}%+%d;%p2%dH$<5>, dsl=\E7\E[1;24r\E8,
fsl=\E8, home=\E[2;1H, is2=\E7\E[2;24r\E8,
tsl=\E7\E[1;%p1%dH\E[1K, use=vt100-am,
# Status line at bottom.
# Clearing the screen will clobber status line.
vt100-s-bot|vt100-bot-s|vt100 for use with bottom sysline,
eslok, hs,
lines#23,
dsl=\E7\E[1;24r\E8, fsl=\E8, is2=\E[1;23r\E[23;1H,
tsl=\E7\E[24;%p1%dH\E[1K,
use=vt100-am,
# Most of the `vt100' emulators out there actually emulate a vt102
# This entry (or vt102-nsgr) is probably the right thing to use for
# these.
vt102|dec vt102,
mir,
dch1=\E[P, dl1=\E[M, il1=\E[L, rmir=\E[4l, smir=\E[4h, use=vt100,
vt102-w|dec vt102 in wide mode,
cols#132,
rs3=\E[?3h, use=vt102,
# Many brain-dead PC comm programs that pretend to be `vt100-compatible'
# fail to interpret the ^O and ^N escapes properly. Symptom: the
# string in the canonical vt100 entry above leaves the screen littered
# with little snowflake or star characters (IBM PC ROM character \017 = ^O)
# after highlight turnoffs. This entry should fix that, and even leave
# ACS support working, at the cost of making multiple-highlight changes
# slightly more expensive.
# From: Eric S. Raymond July 22 1995
vt102-nsgr|vt102 no sgr (use if you see snowflakes after highlight changes),
sgr@, sgr0=\E[m,
use=vt102,
# VT125 Graphics CRT. Clear screen also erases graphics
vt125|vt125 graphics terminal,
clear=\E[H\E[2J\EPpS(E)\E\\$<50>, use=vt100,
# This isn't a DEC entry, it came from University of Wisconsin.
# (vt131: I added / based on the init string, also -- esr)
vt131|dec vt131,
am, xenl,
cols#80, it#8, lines#24, vt#3,
bel=^G, blink=\E[5m$<2/>, bold=\E[1m$<2/>,
clear=\E[;H\E[2J$<50/>, cr=^M, csr=\E[%i%p1%d;%p2%dr,
cub1=^H, cud1=^J, cuf1=\E[C$<2/>,
cup=\E[%i%p1%d;%p2%dH$<5/>, cuu1=\E[A$<2/>,
ed=\E[J$<50/>, el=\E[K$<3/>, home=\E[H, ht=^I,
is2=\E[1;24r\E[24;1H, kbs=^H, kcub1=\EOD, kcud1=\EOB,
kcuf1=\EOC, kcuu1=\EOA, kf1=\EOP, kf2=\EOQ, kf3=\EOR,
kf4=\EOS, nel=^M^J, rc=\E8, rev=\E[7m$<2/>, ri=\EM$<5/>,
rmam=\E[?7h, rmkx=\E[?1l\E>, rmso=\E[m$<2/>,
rmul=\E[m$<2/>,
rs1=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, sc=\E7,
sgr0=\E[m$<2/>, smam=\E[?7h, smkx=\E[?1h\E=,
smso=\E[7m$<2/>, smul=\E[4m$<2/>,
# vt132 - like vt100 but slower and has ins/del line and such.
# I'm told that / are backwards in the terminal from the
# manual and from the ANSI standard, this describes the actual
# terminal. I've never actually used a vt132 myself, so this
# is untested.
#
vt132|DEC vt132,
xenl,
dch1=\E[P$<7>, dl1=\E[M$<99>, il1=\E[L$<99>, ind=\n$<30>,
ip=$<7>, rmir=\E[4h, smir=\E[4l,
use=vt100,
# This vt220 description maps F5--F9 to the second block of function keys
# at the top of the keyboard. The "DO" key is used as F10 to avoid conflict
# with the key marked (ESC) on the vt220. See vt220d for an alternate mapping.
# PF1--PF4 are used as F1--F4.
#
vt220-old|vt200-old|DEC VT220 in vt100 emulation mode,
am, mir, xenl, xon,
cols#80, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m$<2>, bold=\E[1m$<2>, civis=\E[?25l,
clear=\E[H\E[2J$<50>, cnorm=\E[?25h, cr=^M,
csr=\E[%i%p1%d;%p2%dr, cub1=^H, cud1=\E[B, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH$<10>, cuu1=\E[A, dch1=\E[P,
dl1=\E[M, ed=\E[J$<50>, el=\E[K$<3>, home=\E[H, ht=^I,
if=/usr/share/tabset/vt100, il1=\E[L, ind=\ED$<20/>,
is2=\E[1;24r\E[24;1H, kbs=^H, kcub1=\E[D, kcud1=\E[B,
kcuf1=\E[C, kcuu1=\E[A, kdch1=\E[3~, kend=\E[4~, kf1=\EOP,
kf10=\E[29~, kf2=\EOQ, kf3=\EOR, kf4=\EOS, kf5=\E[17~,
kf6=\E[18~, kf7=\E[19~, kf8=\E[20~, kf9=\E[21~,
khome=\E[1~, kich1=\E[2~, knp=\E[6~, kpp=\E[5~, rc=\E8,
rev=\E[7m$<2>, rf=/usr/share/tabset/vt100,
ri=\EM$<14/>, rmacs=\E(B$<4>, rmam=\E[?7l, rmir=\E[4l,
rmso=\E[27m, rmul=\E[24m,
rs2=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, sc=\E7,
sgr=\E[0%?%p6%t;1%;%?%p2%t;4%;%?%p4%t;5%;%?%p1%p3%|%t;7%;m%?%p9%t\E(0%e\E(B%;,
sgr0=\E[m$<2>, smacs=\E(0$<2>, smam=\E[?7h, smir=\E[4h,
smso=\E[7m, smul=\E[4m,
# A much better description of the VT200/220; used to be vt220-8
vt220|vt200|dec vt220,
am, mc5i, mir, msgr, xenl, xon,
cols#80, it#8, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[J, cr=^M,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
ech=\E[%p1%dX, ed=\E[J, el=\E[K, el1=\E[1K, enacs=\E)0,
flash=\E[?5h$<200/>\E[?5l, home=\E[H, ht=^I, hts=\EH,
ich=\E[%p1%d@, if=/usr/share/tabset/vt100,
il=\E[%p1%dL, il1=\E[L, ind=\ED,
is2=\E[?7h\E[>\E[?1h\E F\E[?4l, kbs=^H, kcub1=\E[D,
kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kf1=\EOP, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf13=\E[25~, kf14=\E[26~,
kf17=\E[31~, kf18=\E[32~, kf19=\E[33~, kf2=\EOQ,
kf20=\E[34~, kf3=\EOR, kf4=\EOS, kf6=\E[17~, kf7=\E[18~,
kf8=\E[19~, kf9=\E[20~, kfnd=\E[1~, khlp=\E[28~,
khome=\E[H, kich1=\E[2~, knp=\E[6~, kpp=\E[5~, krdo=\E[29~,
kslt=\E[4~, lf1=pf1, lf2=pf2, lf3=pf3, lf4=pf4, mc0=\E[i,
mc4=\E[4i, mc5=\E[5i, nel=\EE, rc=\E8, rev=\E[7m, ri=\EM,
rmacs=^O, rmam=\E[?7l, rmir=\E[4l, rmso=\E[27m,
rmul=\E[24m, rs1=\E[?3l, sc=\E7, sgr0=\E[m, smacs=^N,
smam=\E[?7h, smir=\E[4h, smso=\E[7m, smul=\E[4m, tbc=\E[3g,
vt220-w|vt200-w|DEC vt220 in wide mode,
cols#132,
rs3=\E[?3h, use=vt220,
vt220-8bit|vt220-8|vt200-8bit|vt200-8|dec vt220/200 in 8-bit mode,
am, mc5i, mir, msgr, xenl, xon,
cols#80, it#8, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\2335m, bold=\2331m, clear=\233H\233J, cr=^M,
csr=\233%i%p1%d;%p2%dr, cub=\233%p1%dD, cub1=^H,
cud=\233%p1%dB, cud1=^J, cuf=\233%p1%dC, cuf1=\233C,
cup=\233%i%p1%d;%p2%dH, cuu=\233%p1%dA, cuu1=\233A,
dch=\233%p1%dP, dch1=\233P, dl=\233%p1%dM, dl1=\233M,
ech=\233%p1%dX, ed=\233J, el=\233K, el1=\2331K, enacs=\E)0,
flash=\233?5h$<200/>\233?5l, home=\233H, ht=^I, hts=\EH,
ich=\233%p1%d@, if=/usr/share/tabset/vt100,
il=\233%p1%dL, il1=\233L, ind=\ED,
is2=\233?7h\233>\233?1h\E F\233?4l, kbs=^H,
kcub1=\233D, kcud1=\233B, kcuf1=\233C, kcuu1=\233A,
kf1=\EOP, kf10=\23321~, kf11=\23323~, kf12=\23324~,
kf13=\23325~, kf14=\23326~, kf17=\23331~, kf18=\23332~,
kf19=\23333~, kf2=\EOQ, kf20=\23334~, kf3=\EOR, kf4=\EOS,
kf6=\23317~, kf7=\23318~, kf8=\23319~, kf9=\23320~,
kfnd=\2331~, khlp=\23328~, khome=\233H, kich1=\2332~,
knp=\2336~, kpp=\2335~, krdo=\23329~, kslt=\2334~, lf1=pf1,
lf2=pf2, lf3=pf3, lf4=pf4, mc0=\233i, mc4=\2334i, mc5=\2335i,
nel=\EE, rc=\E8, rev=\2337m, ri=\EM, rmacs=^O, rmam=\233?7l,
rmir=\2334l, rmso=\23327m, rmul=\23324m, rs1=\233?3l,
sc=\E7, sgr0=\233m, smacs=^N, smam=\233?7h, smir=\2334h,
smso=\2337m, smul=\2334m, tbc=\2333g,
#
# vt220d:
# This vt220 description regards F6--F10 as the second block of function keys
# at the top of the keyboard. This mapping follows the description given
# in the VT220 Programmer Reference Manual and agrees with the labeling
# on some terminals that emulate the vt220. There is no support for an F5.
# See vt220 for an alternate mapping.
#
vt220d|DEC VT220 in vt100 mode with DEC function key labeling,
kf10=\E[21~, kf11=\E[23~, kf12=\E[24~, kf13=\E[25~,
kf14=\E[26~, kf15=\E[28~, kf16=\E[29~, kf17=\E[31~,
kf18=\E[32~, kf19=\E[33~, kf20=\E[34~, kf5@, kf6=\E[17~,
kf7=\E[18~, kf8=\E[19~, kf9=\E[20~,
use=vt220-old,
vt220-nam|v200-nam|VT220 in vt100 mode with no auto margins,
am@,
rs2=\E>\E[?3l\E[?4l\E[?5l\E[?7l\E[?8h, use=vt220,
# vt220 termcap written Tue Oct 25 20:41:10 1988 by Alex Latzko
# (not an official DEC entry!)
# The problem with real vt220 terminals is they don't send escapes when in
# in vt220 mode. This can be gotten around two ways. 1> don't send
# escapes or 2> put the vt220 into vt100 mode and use all the nifty
# features of vt100 advanced video which it then has.
#
# This entry takes the view of putting a vt220 into vt100 mode so
# you can use the escape key in emacs and everything else which needs it.
#
# You probably don't want to use this on a VMS machine since VMS will think
# it has a vt220 and will get fouled up coming out of emacs
#
# From: Alexander Latzko , 30 Dec 1996
# (Added vt100 , to quiet a tic warning -- esr)
vt200-js|vt220-js|dec vt200 series with jump scroll,
am,
cols#80,
bel=^G, clear=\E[H\E[J, cr=^M, csr=\E[%i%p1%d;%p2%dr,
cub1=^H, cud1=^J, cup=\E[%i%p1%d;%p2%dH, cuu1=\E[A,
dch1=\E[P, dl1=\E[M, ed=\E[J, el=\E[K, home=\E[H, ht=^I,
il1=\E[L, ind=\ED,
is2=\E[61"p\E[H\E[?3l\E[?4l\E[?1l\E[?5l\E[?6l\E[?7h\E[?8h\E[?25h\E>\E[m,
kbs=^H, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, nel=^M\ED, rc=\E8,
rf=/usr/lib/tabset/vt100, ri=\EM, rmdc=, rmir=\E[4l,
rmkx=\E[?1l\E>, rmso=\E[27m$<5/>, rmul=\E[24m,
rs1=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, sc=\E7, smdc=,
smir=\E[4h, smkx=\E[?1h\E=, smso=\E[7m$<5/>, smul=\E[4m,
# This was DEC's vt320. Use the purpose-built one below instead
#vt320|DEC VT320 in vt100 emulation mode,
# use=vt220,
#
# Use v320n for SCO's LYRIX. Otherwise, use Adam Thompson's vt320-nam.
#
vt320nam|v320n|DEC VT320 in vt100 emul. mode with NO AUTO WRAP mode,
am@,
rs2=\E>\E[?3l\E[?4l\E[?5l\E[?7l\E[?8h, use=vt220,
# These entries are not DEC's official ones, they were purpose-built for the
# VT320. Here are the designer's notes:
# is end on a PC kbd. Actually 'select' on a VT. Mapped to
# 'Erase to End of Field'... since nothing seems to use 'end' anyways...
# khome is Home on a PC kbd. Actually 'FIND' on a VT.
# Things that use usually use tab anyways... and things that don't use
# tab usually use instead...
# kprv is same as tab - Backtab is useless...
# I left out because of its RIDICULOUS complexity,
# and the resulting fact that it causes the termcap translation of the entry
# to SMASH the 1k-barrier...
# From: Adam Thompson Sept 10 1995
# (vt320: uncommented , comnmmented out to avoid a conflict --esr)
vt320|vt300|dec vt320 7 bit terminal,
am, eslok, hs, mir, msgr, xenl,
cols#80, lines#24, wsl#80,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, civis=\E[?25l,
clear=\E[H\E[2J, cnorm=\E[?25h, cr=^M,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
ech=\E[%p1%dX, ed=\E[J, el=\E[K, el1=\E[1K, fsl=\E[0$},
home=\E[H, ht=^I, hts=\EH, ich=\E[%p1%d@, il=\E[%p1%dL,
il1=\E[L, ind=\ED,
is2=\E>\E[?3l\E[?4l\E[5?l\E[?7h\E[?8h\E[1;24r\E[24;1H,
ka1=\EOw, ka3=\EOy, kb2=\EOu, kbs=\177, kc1=\EOq, kc3=\EOs,
kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kdch1=\E[3~, kel=\E[4~, kent=\EOM, kf1=\EOP, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf13=\E[25~, kf14=\E[26~,
kf15=\E[28~, kf16=\E[29~, kf17=\E[31~, kf18=\E[32~,
kf19=\E[33~, kf2=\EOQ, kf20=\E[34~, kf3=\EOR, kf4=\EOS,
kf6=\E[17~, kf7=\E[18~, kf8=\E[19~, kf9=\E[20~,
khome=\E[1~, kich1=\E[2~, knp=\E[6~, knxt=^I, kpp=\E[5~,
kprv=\E[Z, mc0=\E[i, mc4=\E[?4i, mc5=\E[?5i, nel=\EE, rc=\E8,
rev=\E[7m, rf=/usr/share/tabset/vt300, ri=\EM,
rmacs=\E(B, rmam=\E[?7l, rmir=\E[4l, rmkx=\E[?1l\E>,
rmso=\E[m, rmul=\E[m,
rs2=\E>\E[?3l\E[?4l\E[5?l\E[?7h\E[?8h\E[1;24r\E[24;1H,
sc=\E7, sgr0=\E[m, smacs=\E(0, smam=\E[?7h, smir=\E[4h,
smkx=\E[?1h\E=, smso=\E[7m, smul=\E[4m, tbc=\E[3g,
tsl=\E[1$}\E[H\E[K,
vt320-nam|vt300-nam|dec vt320 7 bit terminal with no am to make SAS happy,
am@,
is2=\E>\E[?3l\E[?4l\E[5?l\E[?7l\E[?8h\E[1;24r\E[24;1H,
rs2=\E>\E[?3l\E[?4l\E[5?l\E[?7l\E[?8h\E[1;24r\E[24;1H,
use=vt320,
# We have to init 132-col mode, not 80-col mode.
vt320-w|vt300-w|dec vt320 wide 7 bit terminal,
cols#132, wsl#132,
is2=\E>\E[?3h\E[?4l\E[5?l\E[?7h\E[?8h\E[1;24r\E[24;1H,
rs2=\E>\E[?3h\E[?4l\E[5?l\E[?7h\E[?8h\E[1;24r\E[24;1H,
use=vt320,
vt320-w-nam|vt300-w-nam|dec vt320 wide 7 bit terminal with no am,
am@,
is2=\E>\E[?3h\E[?4l\E[5?l\E[?7l\E[?8h\E[1;24r\E[24;1H,
rs2=\E>\E[?3h\E[?4l\E[5?l\E[?7l\E[?8h\E[1;24r\E[24;1H,
use=vt320-w,
# VT330 and VT340 -- These are ReGIS and SIXEL graphics terminals
# which are pretty much a superset of the VT320. They have the
# host writable status line, yet another different DRCS matrix size,
# and such, but they add the DEC Technical character set, Multiple text
# pages, selectable length pages, and the like. The difference between
# the vt330 and vt340 is that the latter has only 2 planes and a monochrome
# monitor, the former has 4 planes and a color monitor. These terminals
# support VT131 and ANSI block mode, but as with much of these things,
# termcap/terminfo doesn't deal with these features.
#
# Note that this entry is are set up in what was the standard way for GNU
# Emacs v18 terminal modes to deal with the cursor keys in that the arrow
# keys were switched into application mode at the same time the numeric pad
# is switched into application mode. This changes the definitions of the
# arrow keys. Emacs v19 is smarter and mines its keys directly out of
# your termcap or terminfo entry,
#
# From: Daniel Glasser , 13 Oct 1993
# (vt340: string capability "sb=\E[M" corrected to "sr";
# also, added / based on the init string -- esr)
vt340|dec-vt340|vt330|dec-vt330|dec vt340 graphics terminal with 24 line page,
am, eslok, hs, mir, msgr, xenl, xon,
cols#80, it#8, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
blink=\E[5m, bold=\E[1m, civis=\E[?25l, clear=\E[H\E[J,
cnorm=\E[?25h, cr=^M, csr=\E[%i%p1%d;%p2%dr,
cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=^J,
cuf=\E[%p1%dC, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu=\E[%p1%dA, cuu1=\E[A, cvvis=\E[?25h, dch=\E[%p1%dP,
dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
dsl=\E[2$~\r\E[1$}\E[K\E[$}, ed=\E[J, el=\E[K,
flash=\E[?5h\E[?5l$<200/>, fsl=\E[$}, home=\E[H, ht=^I,
hts=\EH, ich=\E[%p1%d@, il=\E[%p1%dL, il1=\E[L, ind=\ED,
is2=\E<\E F\E>\E[?1h\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h\E[1;24r\E[24;1H,
kbs=^H, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, kf6=\E[17~,
kf7=\E[18~, kf8=\E[19~, kf9=\E[20~, lf1=pf1, lf2=pf2,
lf3=pf3, lf4=pf4, nel=^M\ED, rc=\E8, rev=\E[7m,
rf=/usr/share/tabset/vt300, ri=\EM, rmacs=^O,
rmam=\E[?7l, rmir=\E[4l, rmkx=\E[?1l\E>, rmso=\E[27m,
rmul=\E[24m, rs1=\E[?3l, sc=\E7, sgr0=\E[m, smacs=^N,
smam=\E[?7h, smir=\E[4h, smkx=\E[?1h\E=, smso=\E[7m,
smul=\E[4m, tbc=\E[3g, tsl=\E[2$~\E[1$}\E[1;%dH,
# DEC doesn't supply a vt400 description, so we add Daniel Glasser's
# (originally written with vt420 as its primary name, and usable for it).
#
# VT400/420 -- This terminal is a superset of the vt320. It adds the multiple
# text pages and long text pages with selectable length of the vt340, along
# with left and right margins, rectangular area text copy, fill, and erase
# operations, selected region character attribute change operations,
# page memory and rectangle checksums, insert/delete column, reception
# macros, and other features too numerous to remember right now. TERMCAP
# can only take advantage of a few of these added features.
#
# Note that this entry is are set up in what was the standard way for GNU
# Emacs v18 terminal modes to deal with the cursor keys in that the arrow
# keys were switched into application mode at the same time the numeric pad
# is switched into application mode. This changes the definitions of the
# arrow keys. Emacs v19 is smarter and mines its keys directly out of
# your termcap entry,
#
# From: Daniel Glasser , 13 Oct 1993
# (vt400: string capability ":sb=\E[M:" corrected to ":sr=\E[M:";
# also, added / based on the init string -- esr)
vt400|vt400-24|dec-vt400|dec vt400 24x80 column autowrap,
am, eslok, hs, mir, msgr, xenl, xon,
cols#80, it#8, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
blink=\E[5m, bold=\E[1m, civis=\E[?25l,
clear=\E[H\E[J$<10/>, cnorm=\E[?25h, cr=^M,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
cvvis=\E[?25h, dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM,
dl1=\E[M, dsl=\E[2$~\r\E[1$}\E[K\E[$}, ed=\E[J$<10/>,
el=\E[K$<4/>, flash=\E[?5h\E[?5l$<200/>, fsl=\E[$},
home=\E[H, ht=^I, hts=\EH, ich=\E[%p1%d@, ich1=\E[@,
il=\E[%p1%dL, il1=\E[L, ind=\ED,
is2=\E<\E F\E>\E[?1h\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h\E[1;24r\E[24;1H,
kbs=^H, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, kf6=\E[17~,
kf7=\E[18~, kf8=\E[19~, kf9=\E[20~, lf1=pf1, lf2=pf2,
lf3=pf3, lf4=pf4, nel=^M\ED, rc=\E8, rev=\E[7m,
rf=/usr/share/tabset/vt300, ri=\EM, rmacs=^O,
rmam=\E[?7l, rmir=\E[4l, rmkx=\E[?1l\E>, rmso=\E[27m,
rmul=\E[24m, rs1=\E<\E[?3l\E[!p\E[?7h, sc=\E7, sgr0=\E[m,
smacs=^N, smam=\E[?7h, smir=\E[4h, smkx=\E[?1h\E=,
smso=\E[7m, smul=\E[4m, tbc=\E[3g,
tsl=\E[2$~\E[1$}\E[1;%dH,
# (vt420: I removed , it collided with . I also restored
# a missing -- esr)
vt420|DEC VT420,
am, mir, xenl, xon,
cols#80, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m$<2>, bold=\E[1m$<2>,
clear=\E[H\E[2J$<50>, cr=^M, csr=\E[%i%p1%d;%p2%dr,
cub1=^H, cud1=\E[B, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH$<10>, cuu1=\E[A, dch1=\E[P,
dl1=\E[M, ed=\E[J$<50>, el=\E[K$<3>, home=\E[H, ht=^I,
if=/usr/share/tabset/vt300, il1=\E[L, ind=\ED,
is2=\E[1;24r\E[24;1H, is3=\E[?67h\E[64;1"p, kbs=^H,
kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
kdch1=\E[3~, kf1=\EOP, kf10=\E[29~, kf2=\EOQ, kf3=\EOR,
kf4=\EOS, kf5=\E[17~, kf6=\E[18~, kf7=\E[19~, kf8=\E[20~,
kf9=\E[21~, kfnd=\E[1~, kich1=\E[2~, knp=\E[6~, kpp=\E[5~,
kslt=\E[4~, rc=\E8, rev=\E[7m$<2>,
rf=/usr/share/tabset/vt300, ri=\EM, rmacs=\E(B$<4>,
rmam=\E[?7l, rmir=\E[4l, rmkx=\E>,
rmsc=\E[?0;0r\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h,
rmso=\E[m, rmul=\E[m, rs3=\E[?67h\E[64;1"p, sc=\E7,
sgr=\E[0%?%p6%t;1%;%?%p2%t;4%;%?%p4%t;5%;%?%p1%p3%|%t;7%;m%?%p9%t\E(0%e\E(B%;,
sgr0=\E[m$<2>, smacs=\E(0$<2>, smam=\E[?7h, smir=\E[4h,
smkx=\E=, smso=\E[7m, smul=\E[4m,
#
# DEC VT220 and up support DECUDK (user-defined keys). DECUDK (i.e., pfx)
# takes two parameters, the key and the string. Translating the key is
# straightforward (keys 1-5 are not defined on real terminals, though some
# emulators define these):
#
# if (key < 16) then value = key;
# else if (key < 21) then value = key + 1;
# else if (key < 25) then value = key + 2;
# else if (key < 27) then value = key + 3;
# else if (key < 30) then value = key + 4;
# else value = key + 5;
#
# The string must be the hexadecimal equivalent, e.g., "5052494E" for "PRINT".
# There's no provision in terminfo for emitting a string in this format, so the
# application has to know it.
#
vt420pc|DEC VT420 w/PC keyboard,
kdch1=\177, kend=\E[4~, kf1=\E[11~, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf13=\E[11;2~, kf14=\E[12;2~,
kf15=\E[13;2~, kf16=\E[14;2~, kf17=\E[15;2~,
kf18=\E[17;2~, kf19=\E[18;2~, kf2=\E[12~, kf20=\E[19;2~,
kf21=\E[20;2~, kf22=\E[21;2~, kf23=\E[23;2~,
kf24=\E[24;2~, kf25=\E[23~, kf26=\E[24~, kf27=\E[25~,
kf28=\E[26~, kf29=\E[28~, kf3=\E[13~, kf30=\E[29~,
kf31=\E[31~, kf32=\E[32~, kf33=\E[33~, kf34=\E[34~,
kf35=\E[35~, kf36=\E[36~, kf37=\E[23;2~, kf38=\E[24;2~,
kf39=\E[25;2~, kf4=\E[14~, kf40=\E[26;2~, kf41=\E[28;2~,
kf42=\E[29;2~, kf43=\E[31;2~, kf44=\E[32;2~,
kf45=\E[33;2~, kf46=\E[34;2~, kf47=\E[35;2~,
kf48=\E[36;2~, kf5=\E[15~, kf6=\E[17~, kf7=\E[18~,
kf8=\E[19~, kf9=\E[20~, khome=\E[H,
pctrm=USR_TERM\:vt420pcdos\:,
pfx=\EP1;1|%?%{16}%p1%>%t%{0}%e%{21}%p1%>%t%{1}%e%{25}%p1%>%t%{2}%e%{27}%p1%>%t%{3}%e%{30}%p1%>%t%{4}%e%{5}%;%p1%+%d/%p2%s\E\\, use=vt420,
vt420pcdos|DEC VT420 w/PC for DOS Merge,
lines#25,
dispc=%?%p2%{19}%=%t\E\023\021%e%p2%{32}%<%t\E%p2%c%e%p2%{127}%=%t\E\177%e%p2%c%;,
pctrm@,
rmsc=\E[?0;0r\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, sgr@,
sgr0=\E[m, smsc=\E[?1;2r\E[34h,
use=vt420pc,
vt420f|DEC VT420 with VT kbd; VT400 mode; F1-F5 used as Fkeys,
kdch1=\177, kf1=\E[11~, kf10=\E[21~, kf11=\E[23~,
kf12=\E[24~, kf13=\E[25~, kf14=\E[26~, kf15=\E[28~,
kf16=\E[29~, kf17=\E[31~, kf18=\E[32~, kf19=\E[33~,
kf2=\E[12~, kf20=\E[34~, kf3=\E[13~, kf4=\E[14~,
kf5=\E[15~, kf6=\E[17~, kf7=\E[18~, kf8=\E[19~, kf9=\E[20~,
khome=\E[H, lf1=\EOP, lf2=\EOQ, lf3=\EOR, lf4=\EOS,
use=vt420,
vt510|DEC VT510,
use=vt420,
vt510pc|DEC VT510 w/PC keyboard,
use=vt420pc,
vt510pcdos|DEC VT510 w/PC for DOS Merge,
use=vt420pcdos,
# VT520/VT525
#
# The VT520 is a monochrome text terminal capable of managing up to
# four independent sessions in the terminal. It has multiple ANSI
# emulations (VT520, VT420, VT320, VT220, VT100, VT PCTerm, SCO Console)
# and ASCII emulations (WY160/60, PCTerm, 50/50+, 150/120, TVI 950,
# 925 910+, ADDS A2). This terminfo data is for the ANSI emulations only.
#
# Terminal Set-Up is entered by pressing [F3], [Caps Lock]/[F3] or
# [Alt]/[Print Screen] depending upon which keyboard and which
# terminal mode is being used. If Set-Up has been disabled or
# assigned to an unknown key, Set-Up may be entered by pressing
# [F3] as the first key after power up, regardless of keyboard type.
# (vt520: I added / based on the init string, also -- esr)
vt520|DEC VT520,
am, mir, xenl, xon,
cols#80, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m$<2>, bold=\E[1m$<2>,
clear=\E[H\E[2J$<50>, cr=^M, csr=\E[%i%p1%d;%p2%dr,
cub1=^H, cud1=\E[B, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH$<10>, cuu1=\E[A, dch1=\E[P,
dl1=\E[M, ed=\E[J$<50>, el=\E[K$<3>, home=\E[H, ht=^I,
if=/usr/share/tabset/vt300, il1=\E[L, ind=\ED,
is2=\E[1;24r\E[24;1H, is3=\E[?67h\E[64;1"p, kbs=^H,
kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
kdch1=\E[3~, kf0=\E[29~, kf1=\EOP, kf10=\E[29~, kf2=\EOQ,
kf3=\EOR, kf4=\EOS, kf5=\E[17~, kf6=\E[18~, kf7=\E[19~,
kf8=\E[20~, kf9=\E[21~, kfnd=\E[1~, kich1=\E[2~, knp=\E[6~,
kpp=\E[5~, kslt=\E[4~,
pfx=\EP1;1|%?%{16}%p1%>%t%{0}%e%{21}%p1%>%t%{1}%e%{25}%p1%>%t%{2}%e%{27}%p1%>%t%{3}%e%{30}%p1%>%t%{4}%e%{5}%;%p1%+%d/%p2%s\E\\,
rc=\E8, rev=\E[7m$<2>, rf=/usr/share/tabset/vt300,
ri=\EM, rmacs=\E(B$<4>, rmam=\E[?7l, rmir=\E[4l,
rmsc=\E[?0;0r\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h,
rmso=\E[m, rmul=\E[m, rs3=\E[?67h\E[64;1"p, sc=\E7,
sgr=\E[0%?%p6%t;1%;%?%p2%t;4%;%?%p4%t;5%;%?%p1%p3%|%t;7%;m%?%p9%t\E(0%e\E(B%;,
sgr0=\E[m$<2>, smacs=\E(0$<2>, smam=\E[?7h, smir=\E[4h,
smso=\E[7m, smul=\E[4m,
# (vt525: I added / based on the init string;
# removed =\E[m, =\E[m, added -- esr)
vt525|DEC VT525,
am, mir, xenl, xon,
cols#80, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m$<2>, bold=\E[1m$<2>,
clear=\E[H\E[2J$<50>, cr=^M, csr=\E[%i%p1%d;%p2%dr,
cub1=^H, cud1=\E[B, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH$<10>, cuu1=\E[A, dch1=\E[P,
dl1=\E[M, ed=\E[J$<50>, el=\E[K$<3>, home=\E[H, ht=^I,
if=/usr/share/tabset/vt300, il1=\E[L, ind=\ED,
is2=\E[1;24r\E[24;1H, is3=\E[?67h\E[64;1"p, kbs=^H,
kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
kdch1=\E[3~, kf0=\E[29~, kf1=\EOP, kf10=\E[29~, kf2=\EOQ,
kf3=\EOR, kf4=\EOS, kf5=\E[17~, kf6=\E[18~, kf7=\E[19~,
kf8=\E[20~, kf9=\E[21~, kfnd=\E[1~, kich1=\E[2~, knp=\E[6~,
kpp=\E[5~, kslt=\E[4~,
pfx=\EP1;1|%?%{16}%p1%>%t%{0}%e%{21}%p1%>%t%{1}%e%{25}%p1%>%t%{2}%e%{27}%p1%>%t%{3}%e%{30}%p1%>%t%{4}%e%{5}%;%p1%+%d/%p2%s\E\\,
rc=\E8, rev=\E[7m$<2>, rf=/usr/share/tabset/vt300,
ri=\EM, rmacs=\E(B$<4>, rmam=\E[?7l, rmir=\E[4l,
rmsc=\E[?0;0r\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h,
rmso=\E[m, rmul=\E[m, rs3=\E[?67h\E[64;1"p, sc=\E7,
sgr=\E[0%?%p6%t;1%;%?%p2%t;4%;%?%p4%t;5%;%?%p1%p3%|%t;7%;m%?%p9%t\E(0%e\E(B%;,
sgr0=\E[m$<2>, smacs=\E(0$<2>, smam=\E[?7h, smir=\E[4h,
smso=\E[7m, smul=\E[4m,