1 files changed, 0 insertions, 102 deletions
diff --git a/M4-RCs/qpid/dotnet/Qpid.Integration.Tests/framework/Circuit.cs b/M4-RCs/qpid/dotnet/Qpid.Integration.Tests/framework/Circuit.cs
deleted file mode 100644
index d5f0ed15e2..0000000000
--- a/M4-RCs/qpid/dotnet/Qpid.Integration.Tests/framework/Circuit.cs
+++ /dev/null
@@ -1,102 +0,0 @@
-/*
- *
- * Licensed to the Apache Software Foundation (ASF) under one
- * or more contributor license agreements.  See the NOTICE file
- * distributed with this work for additional information
- * regarding copyright ownership.  The ASF licenses this file
- * to you under the Apache License, Version 2.0 (the
- * "License"); you may not use this file except in compliance
- * with the License.  You may obtain a copy of the License at
- *
- *   http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing,
- * software distributed under the License is distributed on an
- * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
- * KIND, either express or implied.  See the License for the
- * specific language governing permissions and limitations
- * under the License.
- *
- */
-using System.Collections.Generic;//.IList;
-
-namespace Apache.Qpid.Integration.Tests.framework
-{
-    /// <summary>
-    /// A Circuit is the basic test unit against which test cases are to be written. A circuit consists of two 'ends', an
-    /// instigating 'publisher' end and a more passive 'receivers' end.
-    ///
-    /// <p/>Once created, the life-cycle of a circuit may be controlled by <see cref="#start()"/>ing it, or <see cref="#close()"/>ing it.
-    /// Once started, the circuit is ready to send messages over. Once closed the circuit can no longer be used.
-    ///
-    /// <p/>The state of the circuit may be taken with the <see cref="#check()"/> method, and asserted against by the
-    /// <see cref="#applyAssertions(System.Collections.Generic.IList)"/> method.
-    ///
-    /// <p/>There is a default test procedure which may be performed against the circuit. The outline of this procedure is:
-    ///
-    /// <p/><pre>
-    /// Start the circuit.
-    /// Send test messages.
-    /// Request a status report.
-    /// Assert conditions on the publishing end of the circuit.
-    /// Assert conditions on the receiving end of the circuit.
-    /// Close the circuit.
-    /// Pass with no failed assertions or fail with a list of failed assertions.
-    /// </pre>
-    ///
-    /// <p/><table id="crc"><caption>CRC Card</caption>
-    /// <tr><th> Responsibilities
-    /// <tr><td> Supply the publishing and receiving ends of a test messaging circuit.
-    /// <tr><td> Start the circuit running.
-    /// <tr><td> Close the circuit down.
-    /// <tr><td> Take a reading of the circuits state.
-    /// <tr><td> Apply assertions against the circuits state.
-    /// <tr><td> Send test messages over the circuit.
-    /// <tr><td> Perform the default test procedue on the circuit.
-    /// </table>
-    /// </summary>
-    public interface Circuit
-    {
-        /// <summary> Gets the interface on the publishing end of the circuit. </summary>
-        ///
-        /// <return> The publishing end of the circuit. </return>
-        Publisher GetPublisher();
-
-        /// <summary> Gets the interface on the receiving end of the circuit. </summary>
-        ///
-        /// <return> The receiving end of the circuit. </return>
-        Receiver GetReceiver();
-
-        /// <summary> Connects and starts the circuit. After this method is called the circuit is ready to send messages. </summary>
-        void Start();
-
-        /// <summary>
-        /// Checks the test circuit. The effect of this is to gather the circuits state, for both ends of the circuit,
-        /// into a report, against which assertions may be checked.
-        /// </summary>
-        void Check();
-
-        /// <summary> Closes the circuit. All associated resources are closed. </summary>
-        void Close();
-
-        /// <summary>
-        /// Applied a list of assertions against the test circuit. The <see cref="#check()"/> method should be called before doing
-        /// this, to ensure that the circuit has gathered its state into a report to assert against.
-        /// </summary>
-        ///
-        /// <param name="assertions"> The list of assertions to apply to the circuit. </param>
-        ///
-        /// <return> Any assertions that failed. </return>
-        IList<Assertion> ApplyAssertions(IList<Assertion> assertions);
-
-        /// <summary>
-        /// Runs the default test procedure against the circuit, and checks that all of the specified assertions hold.
-        /// </summary>
-        ///
-        /// <param name="numMessages"> The number of messages to send using the default test procedure. </param>
-        /// <param name="assertions">  The list of assertions to apply. </param>
-        ///
-        /// <return> Any assertions that failed. </return>
-        IList<Assertion> Test(int numMessages, IList<Assertion> assertions);
-    }
-}
-\ No newline at end of file