arm: Remove sheevaplug board

This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Patch-cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

12 files changed, 1 insertions, 609 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index c1866cc26d..5110a95497 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -56,8 +56,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += \
 	kirkwood-ns2lite.dtb \
 	kirkwood-ns2max.dtb \
 	kirkwood-ns2mini.dtb \
-	kirkwood-pogo_e02.dtb \
-	kirkwood-sheevaplug.dtb
+	kirkwood-pogo_e02.dtb
 
 dtb-$(CONFIG_MACH_S900) += \
 	bubblegum_96.dtb
diff --git a/arch/arm/dts/kirkwood-sheevaplug-common.dtsi b/arch/arm/dts/kirkwood-sheevaplug-common.dtsi
deleted file mode 100644
index 0a698d3b73..0000000000
--- a/arch/arm/dts/kirkwood-sheevaplug-common.dtsi
+++ /dev/null
@@ -1,104 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * kirkwood-sheevaplug-common.dtsi - Common parts for Sheevaplugs
- *
- * Copyright (C) 2013 Simon Baatz <gmbnomis@gmail.com>
- */
-
-#include "kirkwood.dtsi"
-#include "kirkwood-6281.dtsi"
-
-/ {
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x20000000>;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8 earlyprintk";
-		stdout-path = &uart0;
-	};
-
-	ocp@f1000000 {
-		pinctrl: pin-controller@10000 {
-
-			pmx_usb_power_enable: pmx-usb-power-enable {
-				marvell,pins = "mpp29";
-				marvell,function = "gpio";
-			};
-			pmx_led_red: pmx-led-red {
-				marvell,pins = "mpp46";
-				marvell,function = "gpio";
-			};
-			pmx_led_blue: pmx-led-blue {
-				marvell,pins = "mpp49";
-				marvell,function = "gpio";
-			};
-			pmx_sdio_cd: pmx-sdio-cd {
-				marvell,pins = "mpp44";
-				marvell,function = "gpio";
-			};
-			pmx_sdio_wp: pmx-sdio-wp {
-				marvell,pins = "mpp47";
-				marvell,function = "gpio";
-			};
-		};
-		serial@12000 {
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-0 = <&pmx_usb_power_enable>;
-		pinctrl-names = "default";
-
-		usb_power: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio0 29 0>;
-		};
-	};
-};
-
-&nand {
-	status = "okay";
-
-	partition@0 {
-		label = "u-boot";
-		reg = <0x0000000 0x100000>;
-	};
-
-	partition@100000 {
-		label = "uImage";
-		reg = <0x0100000 0x400000>;
-	};
-
-	partition@500000 {
-		label = "root";
-		reg = <0x0500000 0x1fb00000>;
-	};
-};
-
-&mdio {
-	status = "okay";
-
-	ethphy0: ethernet-phy@0 {
-		reg = <0>;
-	};
-};
-
-&eth0 {
-	status = "okay";
-	ethernet0-port@0 {
-		phy-handle = <&ethphy0>;
-	};
-};
diff --git a/arch/arm/dts/kirkwood-sheevaplug.dts b/arch/arm/dts/kirkwood-sheevaplug.dts
deleted file mode 100644
index c73cc904e5..0000000000
--- a/arch/arm/dts/kirkwood-sheevaplug.dts
+++ /dev/null
@@ -1,42 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * kirkwood-sheevaplug.dts - Device tree file for Sheevaplug
- *
- * Copyright (C) 2013 Simon Baatz <gmbnomis@gmail.com>
- */
-
-/dts-v1/;
-
-#include "kirkwood-sheevaplug-common.dtsi"
-
-/ {
-	model = "Globalscale Technologies SheevaPlug";
-	compatible = "globalscale,sheevaplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-
-	ocp@f1000000 {
-		mvsdio@90000 {
-			pinctrl-0 = <&pmx_sdio>;
-			pinctrl-names = "default";
-			status = "okay";
-			/* No CD or WP GPIOs */
-			broken-cd;
-		};
-	};
-
-	gpio-leds {
-		compatible = "gpio-leds";
-		pinctrl-0 = <&pmx_led_blue &pmx_led_red>;
-		pinctrl-names = "default";
-
-		health {
-			label = "sheevaplug:blue:health";
-			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
-			default-state = "keep";
-		};
-
-		misc {
-			label = "sheevaplug:red:misc";
-			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 67f36a9a63..546a3fc00f 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -13,9 +13,6 @@ config TARGET_DS109
 config TARGET_GURUPLUG
 	bool "GuruPlug Board"
 
-config TARGET_SHEEVAPLUG
-	bool "SheevaPlug Board"
-
 config TARGET_LSXL
 	bool "lsxl Board"
 
@@ -67,7 +64,6 @@ config SYS_SOC
 source "board/Marvell/dreamplug/Kconfig"
 source "board/Synology/ds109/Kconfig"
 source "board/Marvell/guruplug/Kconfig"
-source "board/Marvell/sheevaplug/Kconfig"
 source "board/buffalo/lsxl/Kconfig"
 source "board/cloudengines/pogo_e02/Kconfig"
 source "board/d-link/dns325/Kconfig"
diff --git a/board/Marvell/sheevaplug/Kconfig b/board/Marvell/sheevaplug/Kconfig
deleted file mode 100644
index e5f9284729..0000000000
--- a/board/Marvell/sheevaplug/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_SHEEVAPLUG
-
-config SYS_BOARD
-	default "sheevaplug"
-
-config SYS_VENDOR
-	default "Marvell"
-
-config SYS_CONFIG_NAME
-	default "sheevaplug"
-
-endif
diff --git a/board/Marvell/sheevaplug/MAINTAINERS b/board/Marvell/sheevaplug/MAINTAINERS
deleted file mode 100644
index 2b0103d07d..0000000000
--- a/board/Marvell/sheevaplug/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-SHEEVAPLUG BOARD
-M:	Prafulla Wadaskar <prafulla@marvell.com>
-S:	Maintained
-F:	board/Marvell/sheevaplug/
-F:	include/configs/sheevaplug.h
-F:	configs/sheevaplug_defconfig
diff --git a/board/Marvell/sheevaplug/Makefile b/board/Marvell/sheevaplug/Makefile
deleted file mode 100644
index c39dd03e2d..0000000000
--- a/board/Marvell/sheevaplug/Makefile
+++ /dev/null
@@ -1,7 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-
-obj-y	:= sheevaplug.o
diff --git a/board/Marvell/sheevaplug/kwbimage.cfg b/board/Marvell/sheevaplug/kwbimage.cfg
deleted file mode 100644
index f5206451da..0000000000
--- a/board/Marvell/sheevaplug/kwbimage.cfg
+++ /dev/null
@@ -1,144 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-# Refer to doc/README.kwbimage for more details about how-to
-# configure and create kirkwood boot images.
-#
-
-# Boot Media configurations
-BOOT_FROM	nand
-NAND_ECC_MODE	default
-NAND_PAGE_SIZE	0x0800
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b1b9b
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000c30	# DDR Configuration register
-# bit13-0:  0xc30 (3120 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x37543000	# DDR Controller Control Low
-# bit 4:    0=addr/cmd in smame cycle
-# bit 5:    0=clk is driven during self refresh, we don't care for APX
-# bit 6:    0=use recommended falling edge of clk for addr/cmd
-# bit14:    0=input buffer always powered up
-# bit18:    1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31:    0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
-# bit3-0:   TRAS lsbs
-# bit7-4:   TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20:    TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000a33	#  DDR Timing (High)
-# bit6-0:   TRFC
-# bit8-7:   TR2R
-# bit10-9:  TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x000000cc	#  DDR Address Control
-# bit1-0:   00, Cs0width=x8
-# bit3-2:   11, Cs0size=1Gb
-# bit5-4:   00, Cs1width=x8
-# bit7-6:   11, Cs1size=1Gb
-# bit9-8:   00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16:    0,  Cs0AddrSel
-# bit17:    0,  Cs1AddrSel
-# bit18:    0,  Cs2AddrSel
-# bit19:    0,  Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
-# bit0:    0,  OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000	#  DDR Operation
-# bit3-0:   0x0, DDR cmd
-# bit31-4:  0 required
-
-DATA 0xFFD0141C 0x00000C52	#  DDR Mode
-# bit2-0:   2, BurstLen=2 required
-# bit3:     0, BurstType=0 required
-# bit6-4:   4, CL=5
-# bit7:     0, TestMode=0 normal
-# bit8:     0, DLL reset=0 normal
-# bit11-9:  6, auto-precharge write recovery ????????????
-# bit12:    0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000040	#  DDR Extended Mode
-# bit0:    0,  DDR DLL enabled
-# bit1:    0,  DDR drive strenght normal
-# bit2:    0,  DDR ODT control lsd (disabled)
-# bit5-3:  000, required
-# bit6:    1,  DDR ODT control msb, (disabled)
-# bit9-7:  000, required
-# bit10:   0,  differential DQS enabled
-# bit11:   0, required
-# bit12:   0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
-# bit2-0:  111, required
-# bit3  :  1  , MBUS Burst Chop disabled
-# bit6-4:  111, required
-# bit7  :  0
-# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9  :  0  , no half clock cycle addition to dataout
-# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0    required
-
-DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
-# bit0:    1,  Window enabled
-# bit1:    0,  Write Protect disabled
-# bit3-2:  00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x0F, Size (i.e. 256MB)
-
-DATA 0xFFD01508 0x10000000	# CS[1]n Base address to 256Mb
-DATA 0xFFD0150C 0x0FFFFFF5	# CS[1]n Size 256Mb Window enabled for CS1
-
-DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00030000	#  DDR ODT Control (Low)
-DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
-# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
-# bit3-2:  01, ODT1 active NEVER!
-# bit31-4: zero, required
-
-DATA 0xFFD0149C 0x0000E803	# CPU ODT Control
-DATA 0xFFD01480 0x00000001	# DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/Marvell/sheevaplug/sheevaplug.c b/board/Marvell/sheevaplug/sheevaplug.c
deleted file mode 100644
index 0cc7f2b392..0000000000
--- a/board/Marvell/sheevaplug/sheevaplug.c
+++ /dev/null
@@ -1,136 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- */
-
-#include <common.h>
-#include <init.h>
-#include <miiphy.h>
-#include <net.h>
-#include <asm/global_data.h>
-#include <asm/mach-types.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include "sheevaplug.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/*
-	 * default gpio configuration
-	 * There are maximum 64 gpios controlled through 2 sets of registers
-	 * the  below configuration configures mainly initial LED status
-	 */
-	mvebu_config_gpio(SHEEVAPLUG_OE_VAL_LOW,
-			  SHEEVAPLUG_OE_VAL_HIGH,
-			  SHEEVAPLUG_OE_LOW, SHEEVAPLUG_OE_HIGH);
-
-	/* Multi-Purpose Pins Functionality configuration */
-	static const u32 kwmpp_config[] = {
-		MPP0_NF_IO2,
-		MPP1_NF_IO3,
-		MPP2_NF_IO4,
-		MPP3_NF_IO5,
-		MPP4_NF_IO6,
-		MPP5_NF_IO7,
-		MPP6_SYSRST_OUTn,
-		MPP7_GPO,
-		MPP8_UART0_RTS,
-		MPP9_UART0_CTS,
-		MPP10_UART0_TXD,
-		MPP11_UART0_RXD,
-		MPP12_SD_CLK,
-		MPP13_SD_CMD,
-		MPP14_SD_D0,
-		MPP15_SD_D1,
-		MPP16_SD_D2,
-		MPP17_SD_D3,
-		MPP18_NF_IO0,
-		MPP19_NF_IO1,
-		MPP20_GPIO,
-		MPP21_GPIO,
-		MPP22_GPIO,
-		MPP23_GPIO,
-		MPP24_GPIO,
-		MPP25_GPIO,
-		MPP26_GPIO,
-		MPP27_GPIO,
-		MPP28_GPIO,
-		MPP29_TSMP9,
-		MPP30_GPIO,
-		MPP31_GPIO,
-		MPP32_GPIO,
-		MPP33_GPIO,
-		MPP34_GPIO,
-		MPP35_GPIO,
-		MPP36_GPIO,
-		MPP37_GPIO,
-		MPP38_GPIO,
-		MPP39_GPIO,
-		MPP40_GPIO,
-		MPP41_GPIO,
-		MPP42_GPIO,
-		MPP43_GPIO,
-		MPP44_GPIO,
-		MPP45_GPIO,
-		MPP46_GPIO,
-		MPP47_GPIO,
-		MPP48_GPIO,
-		MPP49_GPIO,
-		0
-	};
-	kirkwood_mpp_conf(kwmpp_config, NULL);
-	return 0;
-}
-
-int board_init(void)
-{
-	/*
-	 * arch number of board
-	 */
-	gd->bd->bi_arch_number = MACH_TYPE_SHEEVAPLUG;
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
-	return 0;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-/* Configure and enable MV88E1116 PHY */
-void reset_phy(void)
-{
-	u16 reg;
-	u16 devadr;
-	char *name = "egiga0";
-
-	if (miiphy_set_current_dev(name))
-		return;
-
-	/* command to read PHY dev address */
-	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
-		printf("Err..%s could not read PHY dev address\n",
-			__FUNCTION__);
-		return;
-	}
-
-	/*
-	 * Enable RGMII delay on Tx and Rx for CPU port
-	 * Ref: sec 4.7.2 of chip datasheet
-	 */
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
-	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
-	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
-	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
-	/* reset the phy */
-	miiphy_reset(name, devadr);
-
-	printf("88E1116 Initialized on %s\n", name);
-}
-#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/sheevaplug/sheevaplug.h b/board/Marvell/sheevaplug/sheevaplug.h
deleted file mode 100644
index e026c1b53b..0000000000
--- a/board/Marvell/sheevaplug/sheevaplug.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- */
-
-#ifndef __SHEEVAPLUG_H
-#define __SHEEVAPLUG_H
-
-#define SHEEVAPLUG_OE_LOW		(~(0))
-#define SHEEVAPLUG_OE_HIGH		(~(0))
-#define SHEEVAPLUG_OE_VAL_LOW		(1 << 29)	/* USB_PWEN low */
-#define SHEEVAPLUG_OE_VAL_HIGH		(1 << 17)	/* LED pin high */
-
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG		10
-#define MV88E1116_CPRSP_CR3_REG		21
-#define MV88E1116_MAC_CTRL_REG		21
-#define MV88E1116_PGADR_REG		22
-#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
-
-#endif /* __SHEEVAPLUG_H */
diff --git a/configs/sheevaplug_defconfig b/configs/sheevaplug_defconfig
deleted file mode 100644
index 34da356b8e..0000000000
--- a/configs/sheevaplug_defconfig
+++ /dev/null
@@ -1,55 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_SYS_THUMB_BUILD=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_TARGET_SHEEVAPLUG=y
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0x80000
-CONFIG_IDENT_STRING="\nMarvell-Sheevaplug"
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-sheevaplug"
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_BOOTDELAY=3
-CONFIG_USE_PREBOOT=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_IDE=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_JFFS2=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:512K(uboot),512K(env),4M(kernel),-(rootfs)"
-CONFIG_CMD_UBI=y
-CONFIG_ISO_PARTITION=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_NETCONSOLE=y
-CONFIG_DM=y
-CONFIG_MVSATA_IDE=y
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_DM_RTC=y
-CONFIG_RTC_MV=y
-CONFIG_SYS_NS16550=y
-CONFIG_USB=y
-CONFIG_DM_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_LZMA=y
-CONFIG_BZIP2=y
diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h
deleted file mode 100644
index e1f8fb8ac8..0000000000
--- a/include/configs/sheevaplug.h
+++ /dev/null
@@ -1,73 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009-2014
- * Gerald Kerma <dreagle@doukki.net>
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- */
-
-#ifndef _CONFIG_SHEEVAPLUG_H
-#define _CONFIG_SHEEVAPLUG_H
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131	1	/* CPU Core subversion */
-
-#include "mv-plug-common.h"
-
-/*
- *  Environment variables configurations
- */
-/*
- * max 4k env size is enough, but in case of nand
- * it has to be rounded to sector size
- */
-/*
- * Environment is right behind U-Boot in flash. Make sure U-Boot
- * doesn't grow into the environment area.
- */
-#define CONFIG_BOARD_SIZE_LIMIT		CONFIG_ENV_OFFSET
-
-/*
- * Default environment variables
- */
-#define CONFIG_BOOTCOMMAND		"${x_bootcmd_kernel}; "	\
-	"setenv bootargs ${x_bootargs} ${x_bootargs_root}; "	\
-	"bootm 0x6400000;"
-
-#define CONFIG_EXTRA_ENV_SETTINGS	"x_bootargs=console"	\
-	"=ttyS0,115200 mtdparts="CONFIG_MTDPARTS_DEFAULT	\
-	"x_bootcmd_kernel=nand read 0x6400000 0x100000 0x400000\0" \
-	"x_bootcmd_usb=usb start\0" \
-	"x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0"
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR	0
-#endif /* CONFIG_CMD_NET */
-
-/*
- * SDIO/MMC Card Configuration
- */
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_MVEBU_MMC
-#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
-#endif /* CONFIG_CMD_MMC */
-
-/*
- * SATA driver configuration
- */
-#ifdef CONFIG_IDE
-#define __io
-#define CONFIG_IDE_PREINIT
-#define CONFIG_MVSATA_IDE_USE_PORT0
-#define CONFIG_MVSATA_IDE_USE_PORT1
-#define CONFIG_SYS_ATA_IDE0_OFFSET	MV_SATA_PORT0_OFFSET
-#define CONFIG_SYS_ATA_IDE1_OFFSET	MV_SATA_PORT1_OFFSET
-#endif /* CONFIG_IDE */
-
-#endif /* _CONFIG_SHEEVAPLUG_H */