ARM: dts: dra72: add rev C evm support

Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.

Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

1 files changed, 513 insertions, 0 deletions

diff --git a/arch/arm/dts/dra72-evm-common.dtsi b/arch/arm/dts/dra72-evm-common.dtsi
new file mode 100644
index 0000000000..b0993e5bf7
--- /dev/null
+++ b/arch/arm/dts/dra72-evm-common.dtsi
@@ -0,0 +1,513 @@
+/*
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "dra72x.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
+
+	chosen {
+		stdout-path = &uart1;
+		tick-timer = &timer2;
+	};
+
+	aliases {
+		display0 = &hdmi0;
+	};
+
+	evm_3v3: fixedregulator-evm_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "evm_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	extcon_usb1: extcon_usb1 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	extcon_usb2: extcon_usb2 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	hdmi0: connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&tpd12s015_out>;
+			};
+		};
+	};
+
+	tpd12s015: encoder {
+		compatible = "ti,tpd12s015";
+
+		gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>,	/* P4, CT CP HPD */
+			<&pcf_hdmi 5 GPIO_ACTIVE_HIGH>,	/* P5, LS OE */
+			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tpd12s015_in: endpoint {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tpd12s015_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+};
+
+&dra7_pmx_core {
+	mmc1_pins_default: mmc1_pins_default {
+		pinctrl-single,pins = <
+			0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc2_pins_default: mmc2_pins_default {
+		pinctrl-single,pins = <
+			0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	dcan1_pins_default: dcan1_pins_default {
+		pinctrl-single,pins = <
+			0x3d0   (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
+			0x418   (PULL_UP | MUX_MODE1)	/* wakeup0.dcan1_rx */
+		>;
+	};
+
+	dcan1_pins_sleep: dcan1_pins_sleep {
+		pinctrl-single,pins = <
+			0x3d0   (MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
+			0x418   (MUX_MODE15 | PULL_UP)	/* wakeup0.off */
+		>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tps65917: tps65917@58 {
+		compatible = "ti,tps65917";
+		reg = <0x58>;
+
+		interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>;  /* IRQ_SYS_1N */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		ti,system-power-controller;
+
+		tps65917_pmic {
+			compatible = "ti,tps65917-pmic";
+
+			tps65917_regulators: regulators {
+				smps1_reg: smps1 {
+					/* VDD_MPU */
+					regulator-name = "smps1";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps2_reg: smps2 {
+					/* VDD_CORE */
+					regulator-name = "smps2";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1060000>;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				smps3_reg: smps3 {
+					/* VDD_GPU IVA DSPEVE */
+					regulator-name = "smps3";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				smps4_reg: smps4 {
+					/* VDDS1V8 */
+					regulator-name = "smps4";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps5_reg: smps5 {
+					/* VDD_DDR */
+					regulator-name = "smps5";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				ldo1_reg: ldo1 {
+					/* LDO1_OUT --> SDIO  */
+					regulator-name = "ldo1";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+					regulator-allow-bypass;
+				};
+
+				ldo3_reg: ldo3 {
+					/* VDDA_1V8_PHY */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				ldo5_reg: ldo5 {
+					/* VDDA_1V8_PLL */
+					regulator-name = "ldo5";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo4_reg: ldo4 {
+					/* VDDA_3V_USB: VDDA_USBHS33 */
+					regulator-name = "ldo4";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+			};
+		};
+
+		tps65917_power_button {
+			compatible = "ti,palmas-pwrbutton";
+			interrupt-parent = <&tps65917>;
+			interrupts = <1 IRQ_TYPE_NONE>;
+			wakeup-source;
+			ti,palmas-long-press-seconds = <6>;
+		};
+	};
+
+	pcf_gpio_21: gpio@21 {
+		compatible = "ti,pcf8575";
+		u-boot,i2c-offset-len = <0>;
+		reg = <0x21>;
+		lines-initial-states = <0x1408>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	pcf_hdmi: pcf8575@26 {
+		compatible = "nxp,pcf8575";
+		u-boot,i2c-offset-len = <0>;
+		reg = <0x26>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		/*
+		 * initial state is used here to keep the mdio interface
+		 * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and
+		 * VIN2_S0 driven high otherwise Ethernet stops working
+		 * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
+		 */
+		lines-initial-states = <0x0f2b>;
+
+		p1 {
+			/* vin6_sel_s0: high: VIN6, low: audio */
+			gpio-hog;
+			gpios = <1 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "vin6_sel_s0";
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+	interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+			      <&dra7_pmx_core 0x3e0>;
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	/*
+	 * For the existing IOdelay configuration via U-Boot we don't
+	 * support NAND on dra72-evm. Keep it disabled. Enabling it
+	 * requires a different configuration by U-Boot.
+	 */
+	status = "disabled";
+	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
+	nand@0,0 {
+		/* To use NAND, DIP switch SW5 must be set like so:
+		 * SW5.1 (NAND_SELn) = ON (LOW)
+		 * SW5.9 (GPMC_WPN) = OFF (HIGH)
+		 */
+		compatible = "ti,omap2-nand";
+		reg = <0 0 4>;          /* device IO registers */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>; /* termcount */
+		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */	/* device IO registers */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <16>;
+		gpmc,device-width = <2>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <80>;
+		gpmc,cs-wr-off-ns = <80>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <60>;
+		gpmc,adv-wr-off-ns = <60>;
+		gpmc,we-on-ns = <10>;
+		gpmc,we-off-ns = <50>;
+		gpmc,oe-on-ns = <4>;
+		gpmc,oe-off-ns = <40>;
+		gpmc,access-ns = <40>;
+		gpmc,wr-access-ns = <80>;
+		gpmc,rd-cycle-ns = <80>;
+		gpmc,wr-cycle-ns = <80>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x000020000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00020000 0x00020000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00040000 0x00020000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x00060000 0x00020000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x000c0000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x001c0000 0x00020000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x001e0000 0x00020000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00200000 0x00800000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00a00000 0x0f600000>;
+		};
+	};
+};
+
+&usb2_phy1 {
+	phy-supply = <&ldo4_reg>;
+};
+
+&usb2_phy2 {
+	phy-supply = <&ldo4_reg>;
+};
+
+&omap_dwc3_1 {
+	extcon = <&extcon_usb1>;
+};
+
+&omap_dwc3_2 {
+	extcon = <&extcon_usb2>;
+};
+
+&usb1 {
+	dr_mode = "otg";
+};
+
+&usb2 {
+	dr_mode = "host";
+};
+
+&mmc1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_default>;
+	vmmc_aux-supply = <&ldo1_reg>;
+	bus-width = <4>;
+	/*
+	 * SDCD signal is not being used here - using the fact that GPIO mode
+	 * is a viable alternative
+	 */
+	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
+	max-frequency = <192000000>;
+};
+
+&mmc2 {
+	/* SW5-3 in ON position */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins_default>;
+
+	vmmc-supply = <&evm_3v3>;
+	bus-width = <8>;
+	ti,non-removable;
+	max-frequency = <192000000>;
+};
+
+&mac {
+	status = "okay";
+};
+
+&dcan1 {
+	status = "ok";
+};
+
+&qspi {
+	status = "okay";
+
+	spi-max-frequency = <76800000>;
+	m25p80@0 {
+		compatible = "s25fl256s1", "spi-flash";
+		spi-max-frequency = <64000000>;
+		reg = <0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* MTD partition table.
+		 * The ROM checks the first four physical blocks
+		 * for a valid file to boot and the flash here is
+		 * 64KiB block size.
+		 */
+		partition@0 {
+			label = "QSPI.SPL";
+			reg = <0x00000000 0x000010000>;
+		};
+		partition@1 {
+			label = "QSPI.SPL.backup1";
+			reg = <0x00010000 0x00010000>;
+		};
+		partition@2 {
+			label = "QSPI.SPL.backup2";
+			reg = <0x00020000 0x00010000>;
+		};
+		partition@3 {
+			label = "QSPI.SPL.backup3";
+			reg = <0x00030000 0x00010000>;
+		};
+		partition@4 {
+			label = "QSPI.u-boot";
+			reg = <0x00040000 0x00100000>;
+		};
+		partition@5 {
+			label = "QSPI.u-boot-spl-os";
+			reg = <0x00140000 0x00080000>;
+		};
+		partition@6 {
+			label = "QSPI.u-boot-env";
+			reg = <0x001c0000 0x00010000>;
+		};
+		partition@7 {
+			label = "QSPI.u-boot-env.backup1";
+			reg = <0x001d0000 0x0010000>;
+		};
+		partition@8 {
+			label = "QSPI.kernel";
+			reg = <0x001e0000 0x0800000>;
+		};
+		partition@9 {
+			label = "QSPI.file-system";
+			reg = <0x009e0000 0x01620000>;
+		};
+	};
+};
+
+&dss {
+	status = "ok";
+
+	vdda_video-supply = <&ldo5_reg>;
+};
+
+&hdmi {
+	status = "ok";
+
+	port {
+		hdmi_out: endpoint {
+			remote-endpoint = <&tpd12s015_in>;
+		};
+	};
+};