diff options
| author | Wenyou Yang <wenyou.yang@atmel.com> | 2017-04-18 15:15:49 +0800 |
|---|---|---|
| committer | Simon Glass <sjg@chromium.org> | 2017-05-09 12:14:16 -0600 |
| commit | e95a29e4e5091c01afdfc7754d3d2e3d874abffc (patch) | |
| tree | 46ab94ebce453aa58c9ecbb8428a9cbdcc3fdb50 /board/atmel | |
| parent | 59b37122b10b1d5d1d8c2b6833cc1075e7275892 (diff) | |
| download | u-boot-e95a29e4e5091c01afdfc7754d3d2e3d874abffc.tar.gz | |
board: at91sam9m10g45ek: Clean up code
Since the introduction of the pinctrl and clk drivers and the
device tree files, remove unneeded hard coded related code from
the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Diffstat (limited to 'board/atmel')
| -rw-r--r-- | board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 102 |
1 files changed, 0 insertions, 102 deletions
diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c index 6871916865..2e8ea053fc 100644 --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c @@ -17,11 +17,6 @@ #include <lcd.h> #include <linux/mtd/nand.h> #include <atmel_lcdc.h> -#include <atmel_mci.h> -#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) -#include <net.h> -#endif -#include <netdev.h> DECLARE_GLOBAL_DATA_PTR; @@ -149,39 +144,6 @@ static void at91sam9m10g45ek_usb_hw_init(void) } #endif -#ifdef CONFIG_MACB -static void at91sam9m10g45ek_macb_hw_init(void) -{ - struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA; - - at91_periph_clk_enable(ATMEL_ID_EMAC); - - /* - * Disable pull-up on: - * RXDV (PA15) => PHY normal mode (not Test mode) - * ERX0 (PA12) => PHY ADDR0 - * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0 - * - * PHY has internal pull-down - */ - writel(pin_to_mask(AT91_PIN_PA15) | - pin_to_mask(AT91_PIN_PA12) | - pin_to_mask(AT91_PIN_PA13), - &pioa->pudr); - - at91_phy_reset(); - - /* Re-enable pull-up */ - writel(pin_to_mask(AT91_PIN_PA15) | - pin_to_mask(AT91_PIN_PA12) | - pin_to_mask(AT91_PIN_PA13), - &pioa->puer); - - /* And the pins. */ - at91_macb_hw_init(); -} -#endif - #ifdef CONFIG_LCD vidinfo_t panel_info = { @@ -280,18 +242,8 @@ void lcd_show_board_info(void) #endif /* CONFIG_LCD_INFO */ #endif -#ifdef CONFIG_GENERIC_ATMEL_MCI -int board_mmc_init(bd_t *bis) -{ - at91_mci_hw_init(); - - return atmel_mci_init((void *)ATMEL_BASE_MCI0); -} -#endif - int board_early_init_f(void) { - at91_seriald_hw_init(); return 0; } @@ -313,15 +265,6 @@ int board_init(void) #ifdef CONFIG_CMD_USB at91sam9m10g45ek_usb_hw_init(); #endif -#ifdef CONFIG_HAS_DATAFLASH - at91_spi0_hw_init(1 << 0); -#endif -#ifdef CONFIG_ATMEL_SPI - at91_spi0_hw_init(1 << 4); -#endif -#ifdef CONFIG_MACB - at91sam9m10g45ek_macb_hw_init(); -#endif #ifdef CONFIG_LCD at91sam9m10g45ek_lcd_hw_init(); #endif @@ -340,48 +283,3 @@ void reset_phy(void) { } #endif - -int board_eth_init(bd_t *bis) -{ - int rc = 0; -#ifdef CONFIG_MACB - rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00); -#endif - return rc; -} - -/* SPI chip select control */ -#ifdef CONFIG_ATMEL_SPI -#include <spi.h> - -int spi_cs_is_valid(unsigned int bus, unsigned int cs) -{ - return bus == 0 && cs < 2; -} - -void spi_cs_activate(struct spi_slave *slave) -{ - switch(slave->cs) { - case 1: - at91_set_gpio_output(AT91_PIN_PB18, 0); - break; - case 0: - default: - at91_set_gpio_output(AT91_PIN_PB3, 0); - break; - } -} - -void spi_cs_deactivate(struct spi_slave *slave) -{ - switch(slave->cs) { - case 1: - at91_set_gpio_output(AT91_PIN_PB18, 1); - break; - case 0: - default: - at91_set_gpio_output(AT91_PIN_PB3, 1); - break; - } -} -#endif /* CONFIG_ATMEL_SPI */ |