arm: Remove platinum_picon board

This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

1 files changed, 0 insertions, 183 deletions

diff --git a/board/barco/platinum/spl_picon.c b/board/barco/platinum/spl_picon.c
deleted file mode 100644
index 253a64d28e..0000000000
--- a/board/barco/platinum/spl_picon.c
+++ /dev/null
@@ -1,183 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014 Stefan Roese <sr@denx.de>
- *
- * Based on: gw_ventana_spl.c which is:
- * Copyright (C) 2014 Gateworks Corporation
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <init.h>
-#include <asm/io.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-ddr.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <spl.h>
-
-#include "platinum.h"
-
-#undef RTT_NOM_120OHM	/* use 120ohm Rtt_nom vs 60ohm (lower power) */
-
-/* Configure MX6Q/DUAL mmdc DDR io registers */
-struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
-	/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
-	.dram_sdclk_0 = 0x00020030,
-	.dram_sdclk_1 = 0x00020030,
-	.dram_cas = 0x00020030,
-	.dram_ras = 0x00020030,
-	.dram_reset = 0x00020030,
-	/* SDCKE[0:1]: 100k pull-up */
-	.dram_sdcke0 = 0x00003000,
-	.dram_sdcke1 = 0x00003000,
-	/* SDBA2: pull-up disabled */
-	.dram_sdba2 = 0x00000000,
-	/* SDODT[0:1]: 100k pull-up, 40 ohm */
-	.dram_sdodt0 = 0x00003030,
-	.dram_sdodt1 = 0x00003030,
-	/* SDQS[0:7]: Differential input, 40 ohm */
-	.dram_sdqs0 = 0x00000030,
-	.dram_sdqs1 = 0x00000030,
-	.dram_sdqs2 = 0x00000030,
-	.dram_sdqs3 = 0x00000030,
-	.dram_sdqs4 = 0x00000030,
-	.dram_sdqs5 = 0x00000030,
-	.dram_sdqs6 = 0x00000030,
-	.dram_sdqs7 = 0x00000030,
-	/* DQM[0:7]: Differential input, 40 ohm */
-	.dram_dqm0 = 0x00020030,
-	.dram_dqm1 = 0x00020030,
-	.dram_dqm2 = 0x00020030,
-	.dram_dqm3 = 0x00020030,
-	.dram_dqm4 = 0x00020030,
-	.dram_dqm5 = 0x00020030,
-	.dram_dqm6 = 0x00020030,
-	.dram_dqm7 = 0x00020030,
-};
-
-/* Configure MX6Q/DUAL mmdc GRP io registers */
-struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
-	/* DDR3 */
-	.grp_ddr_type = 0x000c0000,
-	.grp_ddrmode_ctl = 0x00020000,
-	/* disable DDR pullups */
-	.grp_ddrpke = 0x00000000,
-	/* ADDR[00:16], SDBA[0:1]: 40 ohm */
-	.grp_addds = 0x00000030,
-	/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
-	.grp_ctlds = 0x00000030,
-	/* DATA[00:63]: Differential input, 40 ohm */
-	.grp_ddrmode = 0x00020000,
-	.grp_b0ds = 0x00000030,
-	.grp_b1ds = 0x00000030,
-	.grp_b2ds = 0x00000030,
-	.grp_b3ds = 0x00000030,
-	.grp_b4ds = 0x00000030,
-	.grp_b5ds = 0x00000030,
-	.grp_b6ds = 0x00000030,
-	.grp_b7ds = 0x00000030,
-};
-
-/* MT41K256M16HA-125 */
-static struct mx6_ddr3_cfg mt41k256m16ha_125 = {
-	.mem_speed = 1600,
-	.density = 4,		/* 4Gbit */
-	.width = 16,
-	.banks = 8,
-	.rowaddr = 15,
-	.coladdr = 10,
-	.pagesz = 2,
-	.trcd = 1375,
-	.trcmin = 4875,
-	.trasmin = 3500,
-};
-
-/*
- * Values from running the Freescale DDR stress tool via USB
- */
-static struct mx6_mmdc_calibration mx6dq_mmdc_calib = {
-	/* write leveling calibration determine */
-	.p0_mpwldectrl0 = 0x0044004E,
-	.p0_mpwldectrl1 = 0x001F0023,
-	/* Read DQS Gating calibration */
-	.p0_mpdgctrl0 = 0x02480248,
-	.p0_mpdgctrl1 = 0x0210021C,
-	/* Read Calibration: DQS delay relative to DQ read access */
-	.p0_mprddlctl = 0x42444444,
-	/* Write Calibration: DQ/DM delay relative to DQS write access */
-	.p0_mpwrdlctl = 0x36322C32,
-};
-
-static void spl_dram_init(int width)
-{
-	struct mx6_ddr3_cfg *mem = &mt41k256m16ha_125;
-	struct mx6_ddr_sysinfo sysinfo = {
-		/* width of data bus:0=16,1=32,2=64 */
-		.dsize = width / 32,
-		/* config for full 4GB range so that get_mem_size() works */
-		.cs_density = 32, /* 32Gb per CS */
-		/* single chip select */
-		.ncs = 1,
-		.cs1_mirror = 1,
-		.rtt_wr = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Wr = RZQ/4 */
-#ifdef RTT_NOM_120OHM
-		.rtt_nom = 2 /*DDR3_RTT_120_OHM*/,	/* RTT_Nom = RZQ/2 */
-#else
-		.rtt_nom = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Nom = RZQ/4 */
-#endif
-		.walat = 0,	/* Write additional latency */
-		.ralat = 5,	/* Read additional latency */
-		.mif3_mode = 3,	/* Command prediction working mode */
-		.bi_on = 1,	/* Bank interleaving enabled */
-		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
-		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
-		.ddr_type = DDR_TYPE_DDR3,
-		.refsel = 1,	/* Refresh cycles at 32KHz */
-		.refr = 7, 	/* 8 refresh commands per refresh cycle */
-	};
-
-	mx6sdl_dram_iocfg(width, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
-	mx6_dram_cfg(&sysinfo, &mx6dq_mmdc_calib, mem);
-}
-
-/*
- * Called from C runtime startup code (arch/arm/lib/crt0.S:_main)
- * - we have a stack and a place to store GD, both in SRAM
- * - no variable global data is available
- */
-void board_init_f(ulong dummy)
-{
-	/* Setup AIPS and disable watchdog */
-	arch_cpu_init();
-
-	ccgr_init();
-	gpr_init();
-
-	/* UART iomux */
-	board_early_init_f();
-
-	/* Setup GP timer */
-	timer_init();
-
-	/* UART clocks enabled and gd valid - init serial console */
-	preloader_console_init();
-
-	/* Init DDR with 32bit width */
-	spl_dram_init(32);
-
-	/* Clear the BSS */
-	memset(__bss_start, 0, __bss_end - __bss_start);
-
-	/*
-	 * Setup enet related MUXing early to give the PHY
-	 * some time to wake-up from reset
-	 */
-	platinum_setup_enet();
-
-	/* load/boot image from boot device */
-	board_init_r(NULL, 0);
-}