powerpc/t1023rdb: Add T1023 RDB board support

T1023RDB is a Freescale Reference Design Board that hosts the T1023 SoC.

T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - one 1G RGMII port on-board(RTL8211F PHY)
  - one 1G SGMII port on-board(RTL8211F PHY)
  - one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR:  128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging

As well updated T1024RDB to add T1023RDB.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix defconfig files]
Reviewed-by: York Sun <yorksun@freescale.com>

1 files changed, 24 insertions, 3 deletions

diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c
index f611ff07e9..dd386bc3a9 100644
--- a/board/freescale/t102xrdb/eth_t102xrdb.c
+++ b/board/freescale/t102xrdb/eth_t102xrdb.c
@@ -1,6 +1,8 @@
 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
  *
+ * Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
  * SPDX-License-Identifier:     GPL-2.0+
  */
 
@@ -56,6 +58,7 @@ int board_eth_init(bd_t *bis)
 	fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
 
 	switch (srds_s1) {
+#ifdef CONFIG_T1024RDB
 	case 0x95:
 		/* set the on-board RGMII2  PHY */
 		fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
@@ -63,10 +66,17 @@ int board_eth_init(bd_t *bis)
 		/* set 10G XFI with Aquantia AQR105 PHY */
 		fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
 		break;
+#endif
+	case 0x6a:
+	case 0x6b:
 	case 0x77:
 	case 0x135:
 		/* set the on-board 2.5G SGMII AQR105 PHY */
-		fm_info_set_phy_address(FM1_DTSEC3, SGMII_PHY1_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_AQR_PHY_ADDR);
+#ifdef CONFIG_T1023RDB
+		/* set the on-board 1G SGMII RTL8211F PHY */
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_RTK_PHY_ADDR);
+#endif
 		break;
 	default:
 		printf("SerDes protocol 0x%x is not supported on T102xRDB\n",
@@ -81,6 +91,14 @@ int board_eth_init(bd_t *bis)
 			dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
 			fm_info_set_mdio(i, dev);
 			break;
+		case PHY_INTERFACE_MODE_SGMII:
+#if defined(CONFIG_T1023RDB)
+			dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+#elif defined(CONFIG_T1024RDB)
+			dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
+#endif
+			fm_info_set_mdio(i, dev);
+			break;
 		case PHY_INTERFACE_MODE_SGMII_2500:
 			dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
 			fm_info_set_mdio(i, dev);
@@ -110,13 +128,16 @@ int board_eth_init(bd_t *bis)
 void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
 			      enum fm_port port, int offset)
 {
-	if ((fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) &&
-	    (port == FM1_DTSEC3)) {
+#if defined(CONFIG_T1024RDB)
+	if (((fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) ||
+	     (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII)) &&
+			(port == FM1_DTSEC3)) {
 		fdt_set_phy_handle(fdt, compat, addr, "sg_2500_aqr105_phy4");
 		fdt_setprop(fdt, offset, "phy-connection-type",
 			    "sgmii-2500", 10);
 		fdt_status_disabled_by_alias(fdt, "xg_aqr105_phy3");
 	}
+#endif
 }
 
 void fdt_fixup_board_enet(void *fdt)