armv8/ls1043ardb: Add LS1043ARDB board support

LS1043ARDB Specification:
-------------------------
Memory subsystem:
 * 2GByte DDR4 SDRAM (32bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 16 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * XFI 10G port
 * QSGMII with 4x 1G ports
 * Two RGMII ports

PCIe:
 * PCIe2 (Lanes C) to mini-PCIe slot
 * PCIe3 (Lanes D) to PCIe slot

USB 3.0: two super speed USB 3.0 type A ports

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>

1 files changed, 172 insertions, 0 deletions

diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h
new file mode 100644
index 0000000000..f866bed2a7
--- /dev/null
+++ b/include/configs/ls1043a_common.h
@@ -0,0 +1,172 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __LS1043A_COMMON_H
+#define __LS1043A_COMMON_H
+
+#define CONFIG_REMAKE_ELF
+#define CONFIG_FSL_LAYERSCAPE
+#define CONFIG_FSL_LSCH2
+#define CONFIG_LS1043A
+#define CONFIG_SYS_FSL_CLK
+#define CONFIG_GICV2
+
+#include <asm/arch/config.h>
+#ifdef CONFIG_SYS_FSL_SRDS_1
+#define	CONFIG_SYS_HAS_SERDES
+#endif
+
+/* Link Definitions */
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
+
+#define CONFIG_SUPPORT_RAW_INITRD
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F	1
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+#ifndef CONFIG_SYS_FSL_DDR4
+#define CONFIG_SYS_FSL_DDR3		/* Use DDR3 memory */
+#endif
+
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000
+#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY		25000000	/* 25MHz */
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 1024 * 1024)
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0))
+
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/* IFC */
+#define CONFIG_FSL_IFC
+/*
+ * CONFIG_SYS_FLASH_BASE has the final address (core view)
+ * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
+ * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
+ * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
+ */
+#define CONFIG_SYS_FLASH_BASE			0x60000000
+#define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
+
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
+#endif
+
+/* I2C */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_MXC_I2C2
+#define CONFIG_SYS_I2C_MXC_I2C3
+#define CONFIG_SYS_I2C_MXC_I2C4
+
+/* PCIe */
+#define CONFIG_PCI		/* Enable PCI/PCIE */
+#define CONFIG_PCIE1		/* PCIE controller 1 */
+#define CONFIG_PCIE2		/* PCIE controller 2 */
+#define CONFIG_PCIE3		/* PCIE controller 3 */
+#define CONFIG_PCIE_LAYERSCAPE	/* Use common FSL Layerscape PCIe code */
+#define FSL_PCIE_COMPAT "fsl,ls1043a-pcie"
+
+#define CONFIG_SYS_PCI_64BIT
+
+#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF	0x00000000
+#define CONFIG_SYS_PCIE_CFG0_SIZE	0x00001000	/* 4k */
+#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF	0x00001000
+#define CONFIG_SYS_PCIE_CFG1_SIZE	0x00001000	/* 4k */
+
+#define CONFIG_SYS_PCIE_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE_IO_PHYS_OFF	0x00010000
+#define CONFIG_SYS_PCIE_IO_SIZE		0x00010000	/* 64k */
+
+#define CONFIG_SYS_PCIE_MEM_BUS		0x40000000
+#define CONFIG_SYS_PCIE_MEM_PHYS_OFF	0x40000000
+#define CONFIG_SYS_PCIE_MEM_SIZE	0x40000000	/* 1G */
+
+#ifdef CONFIG_PCI
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP
+#define CONFIG_E1000
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_CMD_PCI
+#endif
+
+/* Command line configuration */
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_PING
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
+#define CONFIG_ARCH_EARLY_INIT_R
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_HWCONFIG
+#define HWCONFIG_BUFFER_SIZE		128
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
+	"loadaddr=0x80100000\0"			\
+	"kernel_addr=0x100000\0"		\
+	"ramdisk_addr=0x800000\0"		\
+	"ramdisk_size=0x2000000\0"		\
+	"fdt_high=0xffffffffffffffff\0"		\
+	"initrd_high=0xffffffffffffffff\0"	\
+	"kernel_start=0x61200000\0"		\
+	"kernel_load=0x807f0000\0"		\
+	"kernel_size=0x1000000\0"		\
+	"console=ttyAMA0,38400n8\0"
+
+#define CONFIG_BOOTARGS			"console=ttyS0,115200 root=/dev/ram0 " \
+					"earlycon=uart8250,0x21c0500,115200"
+#define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
+					"$kernel_size && bootm $kernel_load"
+#define CONFIG_BOOTDELAY		10
+
+/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
+#define CONFIG_SYS_PROMPT		"=> "
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Boot args buffer */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING		1
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_MAXARGS		64	/* max command args */
+
+#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
+
+#endif /* __LS1043A_COMMON_H */