Merge git://git.denx.de/u-boot-fsl-qoriq

5 files changed, 989 insertions, 0 deletions

diff --git a/include/configs/ls1088a_common.h b/include/configs/ls1088a_common.h
new file mode 100644
index 0000000000..84e9b140d0
--- /dev/null
+++ b/include/configs/ls1088a_common.h
@@ -0,0 +1,205 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __LS1088_COMMON_H
+#define __LS1088_COMMON_H
+
+
+#define CONFIG_REMAKE_ELF
+#define CONFIG_FSL_LAYERSCAPE
+#define CONFIG_MP
+
+#include <asm/arch/stream_id_lsch3.h>
+#include <asm/arch/config.h>
+#include <asm/arch/soc.h>
+
+/* Link Definitions */
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
+
+/* Link Definitions */
+#ifdef CONFIG_QSPI_BOOT
+#define CONFIG_SYS_TEXT_BASE            0x20100000
+#else
+#define CONFIG_SYS_TEXT_BASE		0x30100000
+#endif
+
+#define CONFIG_SUPPORT_RAW_INITRD
+
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+#define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
+
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000UL
+#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_BLOCK2_BASE	0x8080000000ULL
+#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS	1
+/*
+ * SMP Definitinos
+ */
+#define CPU_RELEASE_ADDR		secondary_boot_func
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#endif
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2048 * 1024)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_MXC_I2C4		/* enable I2C bus 4 */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX       1
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE     1
+#define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0) / 2)
+
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/* IFC */
+#define CONFIG_FSL_IFC
+
+/*
+ * During booting, IFC is mapped at the region of 0x30000000.
+ * But this region is limited to 256MB. To accommodate NOR, promjet
+ * and FPGA. This region is divided as below:
+ * 0x30000000 - 0x37ffffff : 128MB : NOR flash
+ * 0x38000000 - 0x3BFFFFFF : 64MB  : Promjet
+ * 0x3C000000 - 0x40000000 : 64MB  : FPGA etc
+ *
+ * To accommodate bigger NOR flash and other devices, we will map IFC
+ * chip selects to as below:
+ * 0x5_1000_0000..0x5_1fff_ffff	Memory Hole
+ * 0x5_2000_0000..0x5_3fff_ffff	IFC CSx (FPGA, NAND and others 512MB)
+ * 0x5_4000_0000..0x5_7fff_ffff	ASIC or others 1GB
+ * 0x5_8000_0000..0x5_bfff_ffff	IFC CS0 1GB (NOR/Promjet)
+ * 0x5_C000_0000..0x5_ffff_ffff	IFC CS1 1GB (NOR/Promjet)
+ *
+ * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
+ * CONFIG_SYS_FLASH_BASE has the final address (core view)
+ * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
+ * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
+ * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
+ */
+
+#define CONFIG_SYS_FLASH_BASE			0x580000000ULL
+#define CONFIG_SYS_FLASH_BASE_PHYS		0x80000000
+#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
+
+#define CONFIG_SYS_FLASH1_BASE_PHYS		0xC0000000
+#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY	0x8000000
+
+#ifndef __ASSEMBLY__
+unsigned long long get_qixis_addr(void);
+#endif
+
+#define QIXIS_BASE				get_qixis_addr()
+#define QIXIS_BASE_PHYS				0x20000000
+#define QIXIS_BASE_PHYS_EARLY			0xC000000
+
+
+#define CONFIG_SYS_NAND_BASE			0x530000000ULL
+#define CONFIG_SYS_NAND_BASE_PHYS		0x30000000
+
+
+/* MC firmware */
+/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
+#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH	    0x20000
+#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET    0x00F00000
+#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH	    0x20000
+#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0x00F20000
+#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH	0x200000
+#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET	0x07000000
+/*
+ * Carve out a DDR region which will not be used by u-boot/Linux
+ *
+ * It will be used by MC and Debug Server. The MC region must be
+ * 512MB aligned, so the min size to hide is 512MB.
+ */
+
+#if defined(CONFIG_FSL_MC_ENET)
+#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE		(512UL * 1024 * 1024)
+#endif
+
+#define CONFIG_FSL_CAAM			/* Enable SEC/CAAM */
+
+/* Command line configuration */
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_CACHE
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
+
+/* Physical Memory Map */
+#define CONFIG_CHIP_SELECTS_PER_CTRL	4
+
+#define CONFIG_NR_DRAM_BANKS		2
+
+#define CONFIG_HWCONFIG
+#define HWCONFIG_BUFFER_SIZE		128
+
+/* #define CONFIG_DISPLAY_CPUINFO */
+
+/* Allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
+	"loadaddr=0x80100000\0"			\
+	"kernel_addr=0x100000\0"		\
+	"ramdisk_addr=0x800000\0"		\
+	"ramdisk_size=0x2000000\0"		\
+	"fdt_high=0xa0000000\0"			\
+	"initrd_high=0xffffffffffffffff\0"	\
+	"kernel_start=0x581000000\0"		\
+	"kernel_load=0xa0000000\0"		\
+	"kernel_size=0x2800000\0"		\
+	"console=ttyAMA0,38400n8\0"		\
+	"mcinitcmd=fsl_mc start mc 0x580a00000"	\
+	" 0x580e00000 \0"
+
+#define CONFIG_BOOTARGS		"console=ttyS0,115200 root=/dev/ram0 " \
+				"earlycon=uart8250,mmio,0x21c0500 " \
+				"ramdisk_size=0x3000000 default_hugepagesz=2m" \
+				" hugepagesz=2m hugepages=256"
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_BOOTCOMMAND	"sf probe 0:0;" \
+				"sf read 0x80200000 0xd00000 0x100000;"\
+				" fsl_mc apply dpl 0x80200000 &&" \
+				" sf read $kernel_load $kernel_start" \
+				" $kernel_size && bootm $kernel_load"
+#else /* NOR BOOT*/
+#define CONFIG_BOOTCOMMAND	"fsl_mc apply dpl 0x580d00000 &&" \
+				" cp.b $kernel_start $kernel_load" \
+				" $kernel_size && bootm $kernel_load"
+#endif
+
+/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Boot args buffer */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING		1
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_MAXARGS		64	/* max command args */
+
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
+
+#endif /* __LS1088_COMMON_H */
diff --git a/include/configs/ls1088aqds.h b/include/configs/ls1088aqds.h
new file mode 100644
index 0000000000..3547b0bbbc
--- /dev/null
+++ b/include/configs/ls1088aqds.h
@@ -0,0 +1,414 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __LS1088A_QDS_H
+#define __LS1088A_QDS_H
+
+#include "ls1088a_common.h"
+
+
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE			0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
+#define CONFIG_ENV_SECT_SIZE		0x40000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
+#define CONFIG_ENV_SECT_SIZE		0x20000
+#define CONFIG_ENV_SIZE			0x20000
+#endif
+
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_QIXIS_I2C_ACCESS
+#define SYS_NO_FLASH
+
+#undef CONFIG_CMD_IMLS
+#define CONFIG_SYS_CLK_FREQ		100000000
+#define CONFIG_DDR_CLK_FREQ		100000000
+#else
+#define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
+#endif
+
+#define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ/4)
+#define COUNTER_FREQUENCY		25000000	/* 25MHz */
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE           0xdeadbeef
+#define SPD_EEPROM_ADDRESS		0x51
+#define CONFIG_SYS_SPD_BUS_NUM		0
+
+
+/*
+ * IFC Definitions
+ */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
+#define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128*1024*1024)
+#define CONFIG_SYS_NOR_AMASK_EARLY	IFC_AMASK(64*1024*1024)
+
+#define CONFIG_SYS_NOR0_CSPR					\
+	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
+	CSPR_PORT_SIZE_16					| \
+	CSPR_MSEL_NOR						| \
+	CSPR_V)
+#define CONFIG_SYS_NOR0_CSPR_EARLY				\
+	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
+	CSPR_PORT_SIZE_16					| \
+	CSPR_MSEL_NOR						| \
+	CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR					\
+	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS)		| \
+	CSPR_PORT_SIZE_16					| \
+	CSPR_MSEL_NOR						| \
+	CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EARLY				\
+	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS_EARLY)	| \
+	CSPR_PORT_SIZE_16					| \
+	CSPR_MSEL_NOR						| \
+	CSPR_V)
+#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(12)
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
+				FTIM0_NOR_TEADC(0x5) | \
+				FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
+				FTIM1_NOR_TRAD_NOR(0x1a) |\
+				FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
+				FTIM2_NOR_TCH(0x4) | \
+				FTIM2_NOR_TWPH(0x0E) | \
+				FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3	0x04000000
+#define CONFIG_SYS_IFC_CCR	0x01000000
+
+#ifndef SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE,\
+					 CONFIG_SYS_FLASH_BASE + 0x40000000}
+#endif
+#endif
+
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_MAX_ECCPOS	256
+#define CONFIG_SYS_NAND_MAX_OOBFREE	2
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
+
+#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
+				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
+				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
+				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x07) | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0x0e)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
+					FTIM2_NAND_TREH(0x0a) | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+
+#define CONFIG_FSL_QIXIS
+#define CONFIG_SYS_I2C_FPGA_ADDR	0x66
+#define QIXIS_LBMAP_SWITCH		6
+#define QIXIS_QMAP_MASK			0xe0
+#define QIXIS_QMAP_SHIFT		5
+#define QIXIS_LBMAP_MASK		0x0f
+#define QIXIS_LBMAP_SHIFT		0
+#define QIXIS_LBMAP_DFLTBANK		0x0e
+#define QIXIS_LBMAP_ALTBANK		0x2e
+#define QIXIS_LBMAP_SD			0x00
+#define QIXIS_LBMAP_SD_QSPI		0x0e
+#define QIXIS_LBMAP_QSPI		0x0e
+#define QIXIS_RCW_SRC_SD		0x40
+#define QIXIS_RCW_SRC_QSPI		0x62
+#define QIXIS_RST_CTL_RESET		0x41
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
+#define	QIXIS_RST_FORCE_MEM		0x01
+#define QIXIS_STAT_PRES1		0xb
+#define QIXIS_SDID_MASK			0x07
+#define QIXIS_ESDHC_NO_ADAPTER		0x7
+
+#define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
+#define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
+					| CSPR_PORT_SIZE_8 \
+					| CSPR_MSEL_GPCM \
+					| CSPR_V)
+#define SYS_FPGA_CSPR_FINAL	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+					| CSPR_PORT_SIZE_8 \
+					| CSPR_MSEL_GPCM \
+					| CSPR_V)
+
+#define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64*1024)
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_SYS_FPGA_CSOR		CSOR_GPCM_ADM_SHIFT(0)
+#else
+#define CONFIG_SYS_FPGA_CSOR		CSOR_GPCM_ADM_SHIFT(12)
+#endif
+/* QIXIS Timing parameters*/
+#define SYS_FPGA_CS_FTIM0	(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define SYS_FPGA_CS_FTIM1	(FTIM1_GPCM_TACO(0xff) | \
+					FTIM1_GPCM_TRAD(0x3f))
+#define SYS_FPGA_CS_FTIM2	(FTIM2_GPCM_TCS(0xf) | \
+					FTIM2_GPCM_TCH(0xf) | \
+					FTIM2_GPCM_TWP(0x3E))
+#define SYS_FPGA_CS_FTIM3	0x0
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_CSPR2_FINAL		SYS_FPGA_CSPR_FINAL
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS2_FTIM0		SYS_FPGA_CS_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		SYS_FPGA_CS_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		SYS_FPGA_CS_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		SYS_FPGA_CS_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
+#define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR_EARLY
+#define CONFIG_SYS_CSPR1_FINAL		CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK_EARLY
+#define CONFIG_SYS_AMASK1_FINAL		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_CSPR3_FINAL		CONFIG_SYS_FPGA_CSPR_FINAL
+#define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_CS_FTIM0
+#define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_CS_FTIM1
+#define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_CS_FTIM2
+#define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_CS_FTIM3
+#endif
+
+#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
+
+/*
+ * I2C bus multiplexer
+ */
+#define I2C_MUX_PCA_ADDR_PRI		0x77
+#define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
+#define I2C_RETIMER_ADDR		0x18
+#define I2C_RETIMER_ADDR2		0x19
+#define I2C_MUX_CH_DEFAULT		0x8
+#define I2C_MUX_CH5			0xD
+
+/*
+* RTC configuration
+*/
+#define RTC
+#define CONFIG_RTC_PCF8563 1
+#define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
+#define CONFIG_CMD_DATE
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM		0
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
+
+/* QSPI device */
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE		(1 << 26)
+#define FSL_QSPI_FLASH_NUM		2
+
+#endif
+
+#ifdef CONFIG_FSL_DSPI
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_EON
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SF_DEFAULT_BUS		1
+#define CONFIG_SF_DEFAULT_CS		0
+#endif
+#endif
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		0x9fffffff
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_FSL_MEMAC
+
+/*  MMC  */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_ESDHC_DETECT_QUIRK ((readb(QIXIS_BASE + QIXIS_STAT_PRES1) & \
+	QIXIS_SDID_MASK) != QIXIS_ESDHC_NO_ADAPTER)
+
+/* Initial environment variables */
+#if defined(CONFIG_QSPI_BOOT)
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
+	"loadaddr=0x90100000\0"			\
+	"kernel_addr=0x100000\0"		\
+	"ramdisk_addr=0x800000\0"		\
+	"ramdisk_size=0x2000000\0"		\
+	"fdt_high=0xa0000000\0"			\
+	"initrd_high=0xffffffffffffffff\0"	\
+	"kernel_start=0x1000000\0"		\
+	"kernel_load=0xa0000000\0"		\
+	"kernel_size=0x2800000\0"		\
+	"mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;"	\
+	"sf read 0x80100000 0xE00000 0x100000;" \
+	"fsl_mc start mc 0x80000000 0x80100000\0"	\
+	"mcmemsize=0x70000000 \0"
+#else	/* NOR BOOT */
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
+	"loadaddr=0x90100000\0"			\
+	"kernel_addr=0x100000\0"		\
+	"ramdisk_addr=0x800000\0"		\
+	"ramdisk_size=0x2000000\0"		\
+	"fdt_high=0xa0000000\0"			\
+	"initrd_high=0xffffffffffffffff\0"	\
+	"kernel_start=0x1000000\0"		\
+	"kernel_load=0xa0000000\0"		\
+	"kernel_size=0x2800000\0"		\
+	"mcinitcmd=fsl_mc start mc 0x580A00000 0x580E00000\0"	\
+	"mcmemsize=0x70000000 \0"
+#endif
+
+#ifdef CONFIG_FSL_MC_ENET
+#define CONFIG_FSL_MEMAC
+#define	CONFIG_PHYLIB
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_TERANETICS
+#define RGMII_PHY1_ADDR		0x1
+#define RGMII_PHY2_ADDR		0x2
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1d
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+
+#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
+#define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1
+#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
+#define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3
+#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
+#define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5
+#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
+#define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7
+#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
+#define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9
+#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
+#define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb
+#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
+#define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd
+#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
+#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
+
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"DPMAC1@xgmii"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+
+#endif
+
+#undef CONFIG_CMDLINE_EDITING
+#include <config_distro_defaults.h>
+#define BOOT_TARGET_DEVICES(func) \
+	func(USB, usb, 0) \
+	func(MMC, mmc, 0) \
+	func(SCSI, scsi, 0) \
+	func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LS1088A_QDS_H */
diff --git a/include/configs/ls1088ardb.h b/include/configs/ls1088ardb.h
new file mode 100644
index 0000000000..3223278dfd
--- /dev/null
+++ b/include/configs/ls1088ardb.h
@@ -0,0 +1,317 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __LS1088A_RDB_H
+#define __LS1088A_RDB_H
+
+#include "ls1088a_common.h"
+
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE			0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
+#define CONFIG_ENV_SECT_SIZE		0x40000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
+#define CONFIG_ENV_SECT_SIZE		0x20000
+#define CONFIG_ENV_SIZE			0x20000
+#endif
+
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_QIXIS_I2C_ACCESS
+#define SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
+#endif
+
+#define CONFIG_SYS_CLK_FREQ		100000000
+#define CONFIG_DDR_CLK_FREQ		100000000
+#define COUNTER_FREQUENCY_REAL		25000000	/* 25MHz */
+#define COUNTER_FREQUENCY		25000000	/* 25MHz */
+
+#define CONFIG_DDR_SPD
+#ifdef CONFIG_EMU
+#define CONFIG_SYS_FSL_DDR_EMU
+#define CONFIG_SYS_MXC_I2C1_SPEED	40000000
+#define CONFIG_SYS_MXC_I2C2_SPEED	40000000
+#else
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#endif
+#define SPD_EEPROM_ADDRESS	0x51
+#define CONFIG_SYS_SPD_BUS_NUM	0	/* SPD on I2C bus 0 */
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+
+
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
+#define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
+#define CONFIG_SYS_NOR_AMASK_EARLY	IFC_AMASK(64 * 1024 * 1024)
+
+#define CONFIG_SYS_NOR0_CSPR					\
+	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
+	CSPR_PORT_SIZE_16					| \
+	CSPR_MSEL_NOR						| \
+	CSPR_V)
+#define CONFIG_SYS_NOR0_CSPR_EARLY				\
+	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
+	CSPR_PORT_SIZE_16					| \
+	CSPR_MSEL_NOR						| \
+	CSPR_V)
+#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(6)
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x1) | \
+				FTIM0_NOR_TEADC(0x1) | \
+				FTIM0_NOR_TEAHC(0x1))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x1) | \
+				FTIM1_NOR_TRAD_NOR(0x1))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x0) | \
+				FTIM2_NOR_TCH(0x0) | \
+				FTIM2_NOR_TWP(0x1))
+#define CONFIG_SYS_NOR_FTIM3	0x04000000
+#define CONFIG_SYS_IFC_CCR	0x01000000
+
+#ifndef SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
+#endif
+#endif
+#define CONFIG_SYS_NAND_MAX_ECCPOS	256
+#define CONFIG_SYS_NAND_MAX_OOBFREE	2
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
+
+#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
+				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
+				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
+				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x07) | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0x0e)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
+					FTIM2_NAND_TREH(0x0a) | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+
+#define CONFIG_FSL_QIXIS
+#define CONFIG_SYS_I2C_FPGA_ADDR	0x66
+#define QIXIS_LBMAP_SWITCH		2
+#define QIXIS_QMAP_MASK			0xe0
+#define QIXIS_QMAP_SHIFT		5
+#define QIXIS_LBMAP_MASK		0x1f
+#define QIXIS_LBMAP_SHIFT		5
+#define QIXIS_LBMAP_DFLTBANK		0x00
+#define QIXIS_LBMAP_ALTBANK		0x20
+#define QIXIS_LBMAP_SD			0x00
+#define QIXIS_LBMAP_SD_QSPI		0x00
+#define QIXIS_LBMAP_QSPI		0x00
+#define QIXIS_RCW_SRC_SD		0x40
+#define QIXIS_RCW_SRC_QSPI		0x62
+#define QIXIS_RST_CTL_RESET		0x31
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
+#define	QIXIS_RST_FORCE_MEM		0x01
+
+#define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
+#define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
+					| CSPR_PORT_SIZE_8 \
+					| CSPR_MSEL_GPCM \
+					| CSPR_V)
+#define SYS_FPGA_CSPR_FINAL	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+					| CSPR_PORT_SIZE_8 \
+					| CSPR_MSEL_GPCM \
+					| CSPR_V)
+
+#define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64*1024)
+#define CONFIG_SYS_FPGA_CSOR		CSOR_GPCM_ADM_SHIFT(0)
+/* QIXIS Timing parameters*/
+#define SYS_FPGA_CS_FTIM0	(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define SYS_FPGA_CS_FTIM1	(FTIM1_GPCM_TACO(0xff) | \
+					FTIM1_GPCM_TRAD(0x3f))
+#define SYS_FPGA_CS_FTIM2	(FTIM2_GPCM_TCS(0xf) | \
+					FTIM2_GPCM_TCH(0xf) | \
+					FTIM2_GPCM_TWP(0x3E))
+#define SYS_FPGA_CS_FTIM3	0x0
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_CSPR2_FINAL		SYS_FPGA_CSPR_FINAL
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS2_FTIM0		SYS_FPGA_CS_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		SYS_FPGA_CS_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		SYS_FPGA_CS_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		SYS_FPGA_CS_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
+#define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#endif
+
+
+#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
+
+/*
+ * I2C bus multiplexer
+ */
+#define I2C_MUX_PCA_ADDR_PRI		0x77
+#define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
+#define I2C_RETIMER_ADDR		0x18
+#define I2C_MUX_CH_DEFAULT		0x8
+#define I2C_MUX_CH5			0xD
+/*
+* RTC configuration
+*/
+#define RTC
+#define CONFIG_RTC_PCF8563 1
+#define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
+#define CONFIG_CMD_DATE
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM		0
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
+
+/* QSPI device */
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE		(1 << 26)
+#define FSL_QSPI_FLASH_NUM		2
+#endif
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		0x9fffffff
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_FSL_MEMAC
+
+/* Initial environment variables */
+#if defined(CONFIG_QSPI_BOOT)
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
+	"loadaddr=0x90100000\0"			\
+	"kernel_addr=0x100000\0"		\
+	"ramdisk_addr=0x800000\0"		\
+	"ramdisk_size=0x2000000\0"		\
+	"fdt_high=0xa0000000\0"			\
+	"initrd_high=0xffffffffffffffff\0"	\
+	"kernel_start=0x1000000\0"		\
+	"kernel_load=0xa0000000\0"		\
+	"kernel_size=0x2800000\0"		\
+	"mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;"	\
+	"sf read 0x80100000 0xE00000 0x100000;" \
+	"fsl_mc start mc 0x80000000 0x80100000\0"	\
+	"mcmemsize=0x70000000 \0"
+
+#endif
+
+/* MAC/PHY configuration */
+#ifdef CONFIG_FSL_MC_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_GIGE
+#define CONFIG_PHYLIB
+
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_AQUANTIA
+#define AQ_PHY_ADDR1			0x00
+#define AQR105_IRQ_MASK			0x00000004
+
+#define QSGMII1_PORT1_PHY_ADDR		0x0c
+#define QSGMII1_PORT2_PHY_ADDR		0x0d
+#define QSGMII1_PORT3_PHY_ADDR		0x0e
+#define QSGMII1_PORT4_PHY_ADDR		0x0f
+#define QSGMII2_PORT1_PHY_ADDR		0x1c
+#define QSGMII2_PORT2_PHY_ADDR		0x1d
+#define QSGMII2_PORT3_PHY_ADDR		0x1e
+#define QSGMII2_PORT4_PHY_ADDR		0x1f
+
+#define CONFIG_MII
+#define CONFIG_ETHPRIME		"DPMAC1@xgmii"
+#define CONFIG_PHY_GIGE
+#endif
+
+/*  MMC  */
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#endif
+
+#undef CONFIG_CMDLINE_EDITING
+#include <config_distro_defaults.h>
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(USB, usb, 0) \
+	func(MMC, mmc, 0) \
+	func(SCSI, scsi, 0) \
+	func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LS1088A_RDB_H */
diff --git a/include/fsl-mc/ldpaa_wriop.h b/include/fsl-mc/ldpaa_wriop.h
index 8ae0fc071e..0ca49564a9 100644
--- a/include/fsl-mc/ldpaa_wriop.h
+++ b/include/fsl-mc/ldpaa_wriop.h
@@ -69,4 +69,6 @@ void wriop_dpmac_disable(int);
 void wriop_dpmac_enable(int);
 phy_interface_t wriop_dpmac_enet_if(int, int);
 void wriop_init_dpmac_qsgmii(int, int);
+void wriop_init_rgmii(void);
+void wriop_init_dpmac_enet_if(int , phy_interface_t);
 #endif	/* __LDPAA_WRIOP_H */
diff --git a/include/fsl_immap.h b/include/fsl_immap.h
index b1c4fe7969..4f5a19cdc1 100644
--- a/include/fsl_immap.h
+++ b/include/fsl_immap.h
@@ -133,4 +133,55 @@ struct ccsr_ddr {
 	u8	res_e5c[164];
 	u32     debug[64];		/* debug_1 to debug_64 */
 };
+
+#ifdef CONFIG_SYS_FSL_HAS_CCI400
+#define CCI400_CTRLORD_TERM_BARRIER	0x00000008
+#define CCI400_CTRLORD_EN_BARRIER	0
+#define CCI400_SHAORD_NON_SHAREABLE	0x00000002
+#define CCI400_DVM_MESSAGE_REQ_EN	0x00000002
+#define CCI400_SNOOP_REQ_EN		0x00000001
+
+/* CCI-400 registers */
+struct ccsr_cci400 {
+	u32 ctrl_ord;			/* Control Override */
+	u32 spec_ctrl;			/* Speculation Control */
+	u32 secure_access;		/* Secure Access */
+	u32 status;			/* Status */
+	u32 impr_err;			/* Imprecise Error */
+	u8 res_14[0x100 - 0x14];
+	u32 pmcr;			/* Performance Monitor Control */
+	u8 res_104[0xfd0 - 0x104];
+	u32 pid[8];			/* Peripheral ID */
+	u32 cid[4];			/* Component ID */
+	struct {
+		u32 snoop_ctrl;		/* Snoop Control */
+		u32 sha_ord;		/* Shareable Override */
+		u8 res_1008[0x1100 - 0x1008];
+		u32 rc_qos_ord;		/* read channel QoS Value Override */
+		u32 wc_qos_ord;		/* read channel QoS Value Override */
+		u8 res_1108[0x110c - 0x1108];
+		u32 qos_ctrl;		/* QoS Control */
+		u32 max_ot;		/* Max OT */
+		u8 res_1114[0x1130 - 0x1114];
+		u32 target_lat;		/* Target Latency */
+		u32 latency_regu;	/* Latency Regulation */
+		u32 qos_range;		/* QoS Range */
+		u8 res_113c[0x2000 - 0x113c];
+	} slave[5];			/* Slave Interface */
+	u8 res_6000[0x9004 - 0x6000];
+	u32 cycle_counter;		/* Cycle counter */
+	u32 count_ctrl;			/* Count Control */
+	u32 overflow_status;		/* Overflow Flag Status */
+	u8 res_9010[0xa000 - 0x9010];
+	struct {
+		u32 event_select;	/* Event Select */
+		u32 event_count;	/* Event Count */
+		u32 counter_ctrl;	/* Counter Control */
+		u32 overflow_status;	/* Overflow Flag Status */
+		u8 res_a010[0xb000 - 0xa010];
+	} pcounter[4];			/* Performance Counter */
+	u8 res_e004[0x10000 - 0xe004];
+};
+#endif
+
 #endif /* __FSL_IMMAP_H */