diff options
| -rw-r--r-- | arch/arm/Kconfig | 4 | ||||
| -rw-r--r-- | board/freescale/ls1021atwr/Kconfig | 23 | ||||
| -rw-r--r-- | board/freescale/ls1021atwr/MAINTAINERS | 6 | ||||
| -rw-r--r-- | board/freescale/ls1021atwr/Makefile | 7 | ||||
| -rw-r--r-- | board/freescale/ls1021atwr/README | 109 | ||||
| -rw-r--r-- | board/freescale/ls1021atwr/ls1021atwr.c | 482 | ||||
| -rw-r--r-- | configs/ls1021atwr_nor_defconfig | 2 | ||||
| -rw-r--r-- | include/configs/ls1021atwr.h | 273 |
8 files changed, 906 insertions, 0 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index d7ed3e207d..11143a8c38 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -473,6 +473,9 @@ config TARGET_LS2085A_SIMU config TARGET_LS1021AQDS bool "Support ls1021aqds_nor" +config TARGET_LS1021ATWR + bool "Support ls1021atwr_nor" + config TARGET_BALLOON3 bool "Support balloon3" @@ -598,6 +601,7 @@ source "board/eukrea/cpuat91/Kconfig" source "board/faraday/a320evb/Kconfig" source "board/freescale/ls2085a/Kconfig" source "board/freescale/ls1021aqds/Kconfig" +source "board/freescale/ls1021atwr/Kconfig" source "board/freescale/mx23evk/Kconfig" source "board/freescale/mx25pdk/Kconfig" source "board/freescale/mx28evk/Kconfig" diff --git a/board/freescale/ls1021atwr/Kconfig b/board/freescale/ls1021atwr/Kconfig new file mode 100644 index 0000000000..057808df99 --- /dev/null +++ b/board/freescale/ls1021atwr/Kconfig @@ -0,0 +1,23 @@ +if TARGET_LS1021ATWR + +config SYS_CPU + string + default "armv7" + +config SYS_BOARD + string + default "ls1021atwr" + +config SYS_VENDOR + string + default "freescale" + +config SYS_SOC + string + default "ls102xa" + +config SYS_CONFIG_NAME + string + default "ls1021atwr" + +endif diff --git a/board/freescale/ls1021atwr/MAINTAINERS b/board/freescale/ls1021atwr/MAINTAINERS new file mode 100644 index 0000000000..4e5bc15a0d --- /dev/null +++ b/board/freescale/ls1021atwr/MAINTAINERS @@ -0,0 +1,6 @@ +LS1021ATWR BOARD +M: Alison Wang <alison.wang@freescale.com> +S: Maintained +F: board/freescale/ls1021atwr/ +F: include/configs/ls1021atwr.h +F: configs/ls1021atwr_nor_defconfig diff --git a/board/freescale/ls1021atwr/Makefile b/board/freescale/ls1021atwr/Makefile new file mode 100644 index 0000000000..b5df668713 --- /dev/null +++ b/board/freescale/ls1021atwr/Makefile @@ -0,0 +1,7 @@ +# +# Copyright 2014 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += ls1021atwr.o diff --git a/board/freescale/ls1021atwr/README b/board/freescale/ls1021atwr/README new file mode 100644 index 0000000000..d2821cbb6b --- /dev/null +++ b/board/freescale/ls1021atwr/README @@ -0,0 +1,109 @@ +Overview +-------- +The LS1021ATWR is a Freescale reference board that hosts the LS1021A SoC. + +LS1021A SoC Overview +------------------ +The QorIQ LS1 family, which includes the LS1021A communications processor, +is built on Layerscape architecture, the industry's first software-aware, +core-agnostic networking architecture to offer unprecedented efficiency +and scale. + +A member of the value-performance tier, the QorIQ LS1021A processor provides +extensive integration and power efficiency for fanless, small form factor +enterprise networking applications. Incorporating dual ARM Cortex-A7 cores +running up to 1.0 GHz, the LS1021A processor delivers pre-silicon CoreMark +performance of over 6,000, as well as virtualization support, advanced +security features and the broadest array of high-speed interconnects and +optimized peripheral features ever offered in a sub-3 W processor. + +The QorIQ LS1021A processor features an integrated LCD controller, +CAN controller for implementing industrial protocols, DDR3L/4 running +up to 1600 MHz, integrated security engine and QUICC Engine, and ECC +protection on both L1 and L2 caches. The LS1021A processor is pin- and +software-compatible with the QorIQ LS1020A and LS1022A processors. + +The LS1021A SoC includes the following function and features: + + - ARM Cortex-A7 MPCore compliant with ARMv7-A architecture + - Dual high-preformance ARM Cortex-A7 cores, each core includes: + - 32 Kbyte L1 Instruction Cache and Data Cache for each core (ECC protection) + - 512 Kbyte shared coherent L2 Cache (with ECC protection) + - NEON Co-processor (per core) + - 40-bit physical addressing + - Vector floating-point support + - ARM Core-Link CCI-400 Cache Coherent Interconnect + - One DDR3L/DDR4 SDRAM memory controller with x8/x16/x32-bit configuration + supporting speeds up to 1600Mtps + - ECC and interleaving support + - VeTSEC Ethernet complex + - Up to 3x virtualized 10/100/1000 Ethernet controllers + - MII, RMII, RGMII, and SGMII support + - QoS, lossless flow control, and IEEE 1588 support + - 4-lane 6GHz SerDes + - High speed interconnect (4 SerDes lanes with are muxed for these protocol) + - Two PCI Express Gen2 controllers running at up to 5 GHz + - One Serial ATA 3.0 supporting 6 GT/s operation + - Two SGMII interfaces supporting 1000 Mbps + - Additional peripheral interfaces + - One high-speed USB 3.0 controller with integrated PHY and one high-speed + USB 2.00 controller with ULPI + - Integrated flash controller (IFC) with 16-bit interface + - Quad SPI NOR Flash + - One enhanced Secure digital host controller + - Display controller unit (DCU) 24-bit RGB (12-bit DDR pin interface) + - Ten UARTs comprised of two 16550 compliant DUARTs, and six low power + UARTs + - Three I2C controllers + - Eight FlexTimers four supporting PWM and four FlexCAN ports + - Four GPIO controllers supporting up to 109 general purpose I/O signals + - Integrated advanced audio block: + - Four synchronous audio interfaces (SAI) + - Sony/Philips Digital Interconnect Format (SPDIF) + - Asynchronous Sample Rate Converter (ASRC) + - Hardware based crypto offload engine + - IPSec forwarding at up to 1Gbps + - QorIQ Trust Architecture, Secure Boot, and ARM TrustZone supported + - Public key hardware accelerator + - True Random Number Generator (NIST Certified) + - Advanced Encryption Standard Accelerators (AESA) + - Data Encryption Standard Accelerators + - QUICC Engine ULite block + - Two universal communication controllers (TDM and HDLC) supporting 64 + multichannels, each running at 64 Kbps + - Support for 256 channels of HDLC + - QorIQ TrustArchitecture with Secure Boot, as well as ARM TrustZone supported + +LS1021ATWR board Overview +------------------------- + - DDR Controller + - Supports rates of up to 1600 MHz data-rate + - Supports one DDR3LP SDRAM. + - IFC/Local Bus + - NOR: 128MB 16-bit NOR Flash + - Ethernet + - Three on-board RGMII 10/100/1G ethernet ports. + - CPLD + - Clocks + - System and DDR clock (SYSCLK, DDRCLK) + - SERDES clocks + - Power Supplies + - SDHC + - SDHC/SDXC connector + - Other IO + - One Serial port + - Three I2C ports + +Memory map +----------- +The addresses in brackets are physical addresses. + +Start Address End Address Description Size +0x00_0000_0000 0x00_000F_FFFF Secure Boot ROM 1MB +0x00_0100_0000 0x00_0FFF_FFFF CCSRBAR 240MB +0x00_1000_0000 0x00_1000_FFFF OCRAM0 64KB +0x00_1001_0000 0x00_1001_FFFF OCRAM1 64KB +0x00_2000_0000 0x00_20FF_FFFF DCSR 16MB +0x00_4000_0000 0x00_5FFF_FFFF QSPI 512MB +0x00_6000_0000 0x00_67FF_FFFF IFC - NOR Flash 128MB +0x00_8000_0000 0x00_FFFF_FFFF DRAM1 2GB diff --git a/board/freescale/ls1021atwr/ls1021atwr.c b/board/freescale/ls1021atwr/ls1021atwr.c new file mode 100644 index 0000000000..92ad8cd9bd --- /dev/null +++ b/board/freescale/ls1021atwr/ls1021atwr.c @@ -0,0 +1,482 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <asm/io.h> +#include <asm/arch/immap_ls102xa.h> +#include <asm/arch/clock.h> +#include <asm/arch/fsl_serdes.h> +#include <mmc.h> +#include <fsl_esdhc.h> +#include <fsl_ifc.h> +#include <netdev.h> +#include <fsl_mdio.h> +#include <tsec.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define VERSION_MASK 0x00FF +#define BANK_MASK 0x0001 +#define CONFIG_RESET 0x1 +#define INIT_RESET 0x1 + +#define CPLD_SET_MUX_SERDES 0x20 +#define CPLD_SET_BOOT_BANK 0x40 + +#define BOOT_FROM_UPPER_BANK 0x0 +#define BOOT_FROM_LOWER_BANK 0x1 + +#define LANEB_SATA (0x01) +#define LANEB_SGMII1 (0x02) +#define LANEC_SGMII1 (0x04) +#define LANEC_PCIEX1 (0x08) +#define LANED_PCIEX2 (0x10) +#define LANED_SGMII2 (0x20) + +#define MASK_LANE_B 0x1 +#define MASK_LANE_C 0x2 +#define MASK_LANE_D 0x4 +#define MASK_SGMII 0x8 + +#define KEEP_STATUS 0x0 +#define NEED_RESET 0x1 + +struct cpld_data { + u8 cpld_ver; /* cpld revision */ + u8 cpld_ver_sub; /* cpld sub revision */ + u8 pcba_ver; /* pcb revision number */ + u8 system_rst; /* reset system by cpld */ + u8 soft_mux_on; /* CPLD override physical switches Enable */ + u8 cfg_rcw_src1; /* Reset config word 1 */ + u8 cfg_rcw_src2; /* Reset config word 2 */ + u8 vbank; /* Flash bank selection Control */ + u8 gpio; /* GPIO for TWR-ELEV */ + u8 i2c3_ifc_mux; + u8 mux_spi2; + u8 can3_usb2_mux; /* CAN3 and USB2 Selection */ + u8 qe_lcd_mux; /* QE and LCD Selection */ + u8 serdes_mux; /* Multiplexed pins for SerDes Lanes */ + u8 global_rst; /* reset with init CPLD reg to default */ + u8 rev1; /* Reserved */ + u8 rev2; /* Reserved */ +}; + +static void convert_serdes_mux(int type, int need_reset); + +void cpld_show(void) +{ + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + + printf("CPLD: V%x.%x\nPCBA: V%x.0\nVBank: %d\n", + in_8(&cpld_data->cpld_ver) & VERSION_MASK, + in_8(&cpld_data->cpld_ver_sub) & VERSION_MASK, + in_8(&cpld_data->pcba_ver) & VERSION_MASK, + in_8(&cpld_data->vbank) & BANK_MASK); + +#ifdef CONFIG_DEBUG + printf("soft_mux_on =%x\n", + in_8(&cpld_data->soft_mux_on)); + printf("cfg_rcw_src1 =%x\n", + in_8(&cpld_data->cfg_rcw_src1)); + printf("cfg_rcw_src2 =%x\n", + in_8(&cpld_data->cfg_rcw_src2)); + printf("vbank =%x\n", + in_8(&cpld_data->vbank)); + printf("gpio =%x\n", + in_8(&cpld_data->gpio)); + printf("i2c3_ifc_mux =%x\n", + in_8(&cpld_data->i2c3_ifc_mux)); + printf("mux_spi2 =%x\n", + in_8(&cpld_data->mux_spi2)); + printf("can3_usb2_mux =%x\n", + in_8(&cpld_data->can3_usb2_mux)); + printf("qe_lcd_mux =%x\n", + in_8(&cpld_data->qe_lcd_mux)); + printf("serdes_mux =%x\n", + in_8(&cpld_data->serdes_mux)); +#endif +} + +int checkboard(void) +{ + puts("Board: LS1021ATWR\n"); + cpld_show(); + + return 0; +} + +void ddrmc_init(void) +{ + struct ccsr_ddr *ddr = (struct ccsr_ddr *)CONFIG_SYS_FSL_DDR_ADDR; + + out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG); + + out_be32(&ddr->cs0_bnds, DDR_CS0_BNDS); + out_be32(&ddr->cs0_config, DDR_CS0_CONFIG); + + out_be32(&ddr->timing_cfg_0, DDR_TIMING_CFG_0); + out_be32(&ddr->timing_cfg_1, DDR_TIMING_CFG_1); + out_be32(&ddr->timing_cfg_2, DDR_TIMING_CFG_2); + out_be32(&ddr->timing_cfg_3, DDR_TIMING_CFG_3); + out_be32(&ddr->timing_cfg_4, DDR_TIMING_CFG_4); + out_be32(&ddr->timing_cfg_5, DDR_TIMING_CFG_5); + + out_be32(&ddr->sdram_cfg_2, DDR_SDRAM_CFG_2); + + out_be32(&ddr->sdram_mode, DDR_SDRAM_MODE); + out_be32(&ddr->sdram_mode_2, DDR_SDRAM_MODE_2); + + out_be32(&ddr->sdram_interval, DDR_SDRAM_INTERVAL); + + out_be32(&ddr->ddr_wrlvl_cntl, DDR_DDR_WRLVL_CNTL); + + out_be32(&ddr->ddr_wrlvl_cntl_2, DDR_DDR_WRLVL_CNTL_2); + out_be32(&ddr->ddr_wrlvl_cntl_3, DDR_DDR_WRLVL_CNTL_3); + + out_be32(&ddr->ddr_cdr1, DDR_DDR_CDR1); + out_be32(&ddr->ddr_cdr2, DDR_DDR_CDR2); + + out_be32(&ddr->sdram_clk_cntl, DDR_SDRAM_CLK_CNTL); + out_be32(&ddr->ddr_zq_cntl, DDR_DDR_ZQ_CNTL); + + out_be32(&ddr->cs0_config_2, DDR_CS0_CONFIG_2); + udelay(1); + out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG | DDR_SDRAM_CFG_MEM_EN); +} + +int dram_init(void) +{ +#if (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)) + ddrmc_init(); +#endif + + gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); + return 0; +} + +#ifdef CONFIG_FSL_ESDHC +struct fsl_esdhc_cfg esdhc_cfg[1] = { + {CONFIG_SYS_FSL_ESDHC_ADDR}, +}; + +int board_mmc_init(bd_t *bis) +{ + esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); + + return fsl_esdhc_initialize(bis, &esdhc_cfg[0]); +} +#endif + +#ifdef CONFIG_TSEC_ENET +int board_eth_init(bd_t *bis) +{ + struct fsl_pq_mdio_info mdio_info; + struct tsec_info_struct tsec_info[4]; + int num = 0; + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + if (is_serdes_configured(SGMII_TSEC1)) { + puts("eTSEC1 is in sgmii mode.\n"); + tsec_info[num].flags |= TSEC_SGMII; + } + num++; +#endif +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + if (is_serdes_configured(SGMII_TSEC2)) { + puts("eTSEC2 is in sgmii mode.\n"); + tsec_info[num].flags |= TSEC_SGMII; + } + num++; +#endif +#ifdef CONFIG_TSEC3 + SET_STD_TSEC_INFO(tsec_info[num], 3); + num++; +#endif + if (!num) { + printf("No TSECs initialized\n"); + return 0; + } + + mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; + mdio_info.name = DEFAULT_MII_NAME; + fsl_pq_mdio_init(bis, &mdio_info); + + tsec_eth_init(bis, tsec_info, num); + + return pci_eth_init(bis); +} +#endif + +int config_serdes_mux(void) +{ + struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + u32 protocol = in_be32(&gur->rcwsr[4]) & RCWSR4_SRDS1_PRTCL_MASK; + + protocol >>= RCWSR4_SRDS1_PRTCL_SHIFT; + switch (protocol) { + case 0x10: + convert_serdes_mux(LANEB_SATA, KEEP_STATUS); + convert_serdes_mux(LANED_PCIEX2 | + LANEC_PCIEX1, KEEP_STATUS); + break; + case 0x20: + convert_serdes_mux(LANEB_SGMII1, KEEP_STATUS); + convert_serdes_mux(LANEC_PCIEX1, KEEP_STATUS); + convert_serdes_mux(LANED_SGMII2, KEEP_STATUS); + break; + case 0x30: + convert_serdes_mux(LANEB_SATA, KEEP_STATUS); + convert_serdes_mux(LANEC_SGMII1, KEEP_STATUS); + convert_serdes_mux(LANED_SGMII2, KEEP_STATUS); + break; + case 0x70: + convert_serdes_mux(LANEB_SATA, KEEP_STATUS); + convert_serdes_mux(LANEC_PCIEX1, KEEP_STATUS); + convert_serdes_mux(LANED_SGMII2, KEEP_STATUS); + break; + } + + return 0; +} + +int board_early_init_f(void) +{ + struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR; + +#ifdef CONFIG_TSEC_ENET + out_be32(&scfg->scfgrevcr, SCFG_SCFGREVCR_REV); + out_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR); + out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125); + udelay(10); + out_be32(&scfg->scfgrevcr, SCFG_SCFGREVCR_NOREV); +#endif + +#ifdef CONFIG_FSL_IFC + init_early_memctl_regs(); +#endif + + return 0; +} + +int board_init(void) +{ +#ifndef CONFIG_SYS_FSL_NO_SERDES + fsl_serdes_init(); + config_serdes_mux(); +#endif + + return 0; +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); +} + +u8 flash_read8(void *addr) +{ + return __raw_readb(addr + 1); +} + +void flash_write16(u16 val, void *addr) +{ + u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00)); + + __raw_writew(shftval, addr); +} + +u16 flash_read16(void *addr) +{ + u16 val = __raw_readw(addr); + + return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00); +} + +static void convert_flash_bank(char bank) +{ + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + + printf("Now switch to boot from flash bank %d.\n", bank); + cpld_data->soft_mux_on = CPLD_SET_BOOT_BANK; + cpld_data->vbank = bank; + + printf("Reset board to enable configuration.\n"); + cpld_data->system_rst = CONFIG_RESET; +} + +static int flash_bank_cmd(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) +{ + if (argc != 2) + return CMD_RET_USAGE; + if (strcmp(argv[1], "0") == 0) + convert_flash_bank(BOOT_FROM_UPPER_BANK); + else if (strcmp(argv[1], "1") == 0) + convert_flash_bank(BOOT_FROM_LOWER_BANK); + else + return CMD_RET_USAGE; + + return 0; +} + +U_BOOT_CMD( + boot_bank, 2, 0, flash_bank_cmd, + "Flash bank Selection Control", + "bank[0-upper bank/1-lower bank] (e.g. boot_bank 0)" +); + +static int cpld_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) +{ + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + + if (argc > 2) + return CMD_RET_USAGE; + if ((argc == 1) || (strcmp(argv[1], "conf") == 0)) + cpld_data->system_rst = CONFIG_RESET; + else if (strcmp(argv[1], "init") == 0) + cpld_data->global_rst = INIT_RESET; + else + return CMD_RET_USAGE; + + return 0; +} + +U_BOOT_CMD( + cpld_reset, 2, 0, cpld_reset_cmd, + "Reset via CPLD", + "conf\n" + " -reset with current CPLD configuration\n" + "init\n" + " -reset and initial CPLD configuration with default value" + +); + +static void convert_serdes_mux(int type, int need_reset) +{ + char current_serdes; + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + + current_serdes = cpld_data->serdes_mux; + + switch (type) { + case LANEB_SATA: + current_serdes &= ~MASK_LANE_B; + break; + case LANEB_SGMII1: + current_serdes |= (MASK_LANE_B | MASK_SGMII | MASK_LANE_C); + break; + case LANEC_SGMII1: + current_serdes &= ~(MASK_LANE_B | MASK_SGMII | MASK_LANE_C); + break; + case LANED_SGMII2: + current_serdes |= MASK_LANE_D; + break; + case LANEC_PCIEX1: + current_serdes |= MASK_LANE_C; + break; + case (LANED_PCIEX2 | LANEC_PCIEX1): + current_serdes |= MASK_LANE_C; + current_serdes &= ~MASK_LANE_D; + break; + default: + printf("CPLD serdes MUX: unsupported MUX type 0x%x\n", type); + return; + } + + cpld_data->soft_mux_on |= CPLD_SET_MUX_SERDES; + cpld_data->serdes_mux = current_serdes; + + if (need_reset == 1) { + printf("Reset board to enable configuration\n"); + cpld_data->system_rst = CONFIG_RESET; + } +} + +void print_serdes_mux(void) +{ + char current_serdes; + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + + current_serdes = cpld_data->serdes_mux; + + printf("Serdes Lane B: "); + if ((current_serdes & MASK_LANE_B) == 0) + printf("SATA,\n"); + else + printf("SGMII 1,\n"); + + printf("Serdes Lane C: "); + if ((current_serdes & MASK_LANE_C) == 0) + printf("SGMII 1,\n"); + else + printf("PCIe,\n"); + + printf("Serdes Lane D: "); + if ((current_serdes & MASK_LANE_D) == 0) + printf("PCIe,\n"); + else + printf("SGMII 2,\n"); + + printf("SGMII 1 is on lane "); + if ((current_serdes & MASK_SGMII) == 0) + printf("C.\n"); + else + printf("B.\n"); +} + +static int serdes_mux_cmd(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) +{ + if (argc != 2) + return CMD_RET_USAGE; + if (strcmp(argv[1], "sata") == 0) { + printf("Set serdes lane B to SATA.\n"); + convert_serdes_mux(LANEB_SATA, NEED_RESET); + } else if (strcmp(argv[1], "sgmii1b") == 0) { + printf("Set serdes lane B to SGMII 1.\n"); + convert_serdes_mux(LANEB_SGMII1, NEED_RESET); + } else if (strcmp(argv[1], "sgmii1c") == 0) { + printf("Set serdes lane C to SGMII 1.\n"); + convert_serdes_mux(LANEC_SGMII1, NEED_RESET); + } else if (strcmp(argv[1], "sgmii2") == 0) { + printf("Set serdes lane D to SGMII 2.\n"); + convert_serdes_mux(LANED_SGMII2, NEED_RESET); + } else if (strcmp(argv[1], "pciex1") == 0) { + printf("Set serdes lane C to PCIe X1.\n"); + convert_serdes_mux(LANEC_PCIEX1, NEED_RESET); + } else if (strcmp(argv[1], "pciex2") == 0) { + printf("Set serdes lane C & lane D to PCIe X2.\n"); + convert_serdes_mux((LANED_PCIEX2 | LANEC_PCIEX1), NEED_RESET); + } else if (strcmp(argv[1], "show") == 0) { + print_serdes_mux(); + } else { + return CMD_RET_USAGE; + } + + return 0; +} + +U_BOOT_CMD( + lane_bank, 2, 0, serdes_mux_cmd, + "Multiplexed function setting for SerDes Lanes", + "sata\n" + " -change lane B to sata\n" + "lane_bank sgmii1b\n" + " -change lane B to SGMII1\n" + "lane_bank sgmii1c\n" + " -change lane C to SGMII1\n" + "lane_bank sgmii2\n" + " -change lane D to SGMII2\n" + "lane_bank pciex1\n" + " -change lane C to PCIeX1\n" + "lane_bank pciex2\n" + " -change lane C & lane D to PCIeX2\n" + "\nWARNING: If you aren't familiar with the setting of serdes, don't try to change anything!\n" +); diff --git a/configs/ls1021atwr_nor_defconfig b/configs/ls1021atwr_nor_defconfig new file mode 100644 index 0000000000..5f465d3100 --- /dev/null +++ b/configs/ls1021atwr_nor_defconfig @@ -0,0 +1,2 @@ +CONFIG_ARM=y +CONFIG_TARGET_LS1021ATWR=y diff --git a/include/configs/ls1021atwr.h b/include/configs/ls1021atwr.h new file mode 100644 index 0000000000..cb6b400425 --- /dev/null +++ b/include/configs/ls1021atwr.h @@ -0,0 +1,273 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <config_cmd_default.h> + +#define CONFIG_LS102XA + +#define CONFIG_SYS_GENERIC_BOARD + +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) + +#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE + +/* + * Generic Timer Definitions + */ +#define GENERIC_TIMER_CLK 12500000 + +#define CONFIG_SYS_CLK_FREQ 100000000 +#define CONFIG_DDR_CLK_FREQ 100000000 + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0x67f80000 +#endif + +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM 0x80000000 +#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_SYS_HAS_SERDES + +/* + * IFC Definitions + */ +#define CONFIG_FSL_IFC +#define CONFIG_SYS_FLASH_BASE 0x60000000 +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE + +#define CONFIG_SYS_NOR0_CSPR_EXT (0x0) +#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) + +/* NOR Flash Timing Params */ +#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ + CSOR_NOR_TRHZ_80) +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TAVDS(0x0) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1A) | \ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWP(0x1c) | \ + FTIM2_NOR_TWPH(0x0e)) +#define CONFIG_SYS_NOR_FTIM3 0 + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } + +#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS + +/* CPLD */ + +#define CONFIG_SYS_CPLD_BASE 0x7fb00000 +#define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE + +#define CONFIG_SYS_FPGA_CSPR_EXT (0x0) +#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \ + CSPR_PORT_SIZE_8 | \ + CSPR_MSEL_GPCM | \ + CSPR_V) +#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) +#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ + CSOR_NOR_NOR_MODE_AVD_NOR | \ + CSOR_NOR_TRHZ_80) + +/* CPLD Timing parameters for IFC GPCM */ +#define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \ + FTIM0_GPCM_TEADC(0xf) | \ + FTIM0_GPCM_TEAHC(0xf)) +#define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ + FTIM1_GPCM_TRAD(0x3f)) +#define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ + FTIM2_GPCM_TCH(0xf) | \ + FTIM2_GPCM_TWP(0xff)) +#define CONFIG_SYS_FPGA_FTIM3 0x0 +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_FPGA_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_FPGA_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_FPGA_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_FPGA_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_FPGA_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_FPGA_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_FPGA_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_FPGA_FTIM3 + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +#define CONFIG_BAUDRATE 115200 + +/* + * I2C + */ +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC + +/* + * MMC + */ +#define CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_GENERIC_MMC + +/* + * eTSEC + */ +#define CONFIG_TSEC_ENET + +#ifdef CONFIG_TSEC_ENET +#define CONFIG_MII +#define CONFIG_MII_DEFAULT_TSEC 1 +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "eTSEC3" + +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 0 +#define TSEC3_PHY_ADDR 1 + +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC3_PHYIDX 0 + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE +#define CONFIG_PHYLIB +#define CONFIG_PHY_ATHEROS + +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH2 +#endif + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET + +#define CONFIG_CMDLINE_TAG +#define CONFIG_CMDLINE_EDITING +#define CONFIG_CMD_IMLS + +#define CONFIG_HWCONFIG +#define HWCONFIG_BUFFER_SIZE 128 + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \ + "initrd_high=0xcfffffff\0" \ + "fdt_high=0xcfffffff\0" + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_CMD_ENV_EXISTS +#define CONFIG_CMD_GREPENV +#define CONFIG_CMD_MEMINFO +#define CONFIG_CMD_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END 0x9fffffff + +#define CONFIG_SYS_LOAD_ADDR 0x82000000 +#define CONFIG_SYS_HZ 1000 + +/* + * Stack sizes + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (30 * 1024) + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +/* + * Environment + */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ + +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_CMD_BOOTZ + +#endif |