diff options
| -rw-r--r-- | arch/arm/Kconfig | 5 | ||||
| -rw-r--r-- | board/atmel/sama5d4_xplained/Kconfig | 18 | ||||
| -rw-r--r-- | board/atmel/sama5d4_xplained/MAINTAINERS | 8 | ||||
| -rw-r--r-- | board/atmel/sama5d4_xplained/Makefile | 8 | ||||
| -rw-r--r-- | board/atmel/sama5d4_xplained/sama5d4_xplained.c | 319 | ||||
| -rw-r--r-- | configs/sama5d4_xplained_mmc_defconfig | 3 | ||||
| -rw-r--r-- | configs/sama5d4_xplained_nandflash_defconfig | 3 | ||||
| -rw-r--r-- | configs/sama5d4_xplained_spiflash_defconfig | 3 | ||||
| -rw-r--r-- | include/configs/sama5d4_xplained.h | 216 |
9 files changed, 583 insertions, 0 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 1a83683532..9b492bea3a 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -509,6 +509,10 @@ config TARGET_SAMA5D3XEK select CPU_V7 select SUPPORT_SPL +config TARGET_SAMA5D4_XPLAINED + bool "Support sama5d4_xplained" + select CPU_V7 + config TARGET_SAMA5D4EK bool "Support sama5d4ek" select CPU_V7 @@ -848,6 +852,7 @@ source "board/atmel/at91sam9rlek/Kconfig" source "board/atmel/at91sam9x5ek/Kconfig" source "board/atmel/sama5d3_xplained/Kconfig" source "board/atmel/sama5d3xek/Kconfig" +source "board/atmel/sama5d4_xplained/Kconfig" source "board/atmel/sama5d4ek/Kconfig" source "board/bachmann/ot1200/Kconfig" source "board/balloon3/Kconfig" diff --git a/board/atmel/sama5d4_xplained/Kconfig b/board/atmel/sama5d4_xplained/Kconfig new file mode 100644 index 0000000000..f6440c0b5a --- /dev/null +++ b/board/atmel/sama5d4_xplained/Kconfig @@ -0,0 +1,18 @@ +if TARGET_SAMA5D4_XPLAINED + +config SYS_CPU + default "armv7" + +config SYS_BOARD + default "sama5d4_xplained" + +config SYS_VENDOR + default "atmel" + +config SYS_SOC + default "at91" + +config SYS_CONFIG_NAME + default "sama5d4_xplained" + +endif diff --git a/board/atmel/sama5d4_xplained/MAINTAINERS b/board/atmel/sama5d4_xplained/MAINTAINERS new file mode 100644 index 0000000000..035f64c6ea --- /dev/null +++ b/board/atmel/sama5d4_xplained/MAINTAINERS @@ -0,0 +1,8 @@ +SAMA5D4 XPLAINED ULTRA BOARD +M: Bo Shen <voice.shen@atmel.com> +S: Maintained +F: board/atmel/sama5d4_xplained/ +F: include/configs/sama5d4_xplained.h +F: configs/sama5d4_xplained_mmc_defconfig +F: configs/sama5d4_xplained_nandflash_defconfig +F: configs/sama5d4_xplained_spiflash_defconfig diff --git a/board/atmel/sama5d4_xplained/Makefile b/board/atmel/sama5d4_xplained/Makefile new file mode 100644 index 0000000000..c59b12df24 --- /dev/null +++ b/board/atmel/sama5d4_xplained/Makefile @@ -0,0 +1,8 @@ +# +# Copyright (C) 2014 Atmel +# Bo Shen <voice.shen@atmel.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += sama5d4_xplained.o diff --git a/board/atmel/sama5d4_xplained/sama5d4_xplained.c b/board/atmel/sama5d4_xplained/sama5d4_xplained.c new file mode 100644 index 0000000000..de0baada28 --- /dev/null +++ b/board/atmel/sama5d4_xplained/sama5d4_xplained.c @@ -0,0 +1,319 @@ +/* + * Copyright (C) 2014 Atmel + * Bo Shen <voice.shen@atmel.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/gpio.h> +#include <asm/arch/clk.h> +#include <asm/arch/sama5d3_smc.h> +#include <asm/arch/sama5d4.h> +#include <atmel_lcdc.h> +#include <atmel_mci.h> +#include <lcd.h> +#include <mmc.h> +#include <net.h> +#include <netdev.h> +#include <nand.h> +#include <spi.h> + +DECLARE_GLOBAL_DATA_PTR; + +#ifdef CONFIG_ATMEL_SPI +int spi_cs_is_valid(unsigned int bus, unsigned int cs) +{ + return bus == 0 && cs == 0; +} + +void spi_cs_activate(struct spi_slave *slave) +{ + at91_set_pio_output(AT91_PIO_PORTC, 3, 0); +} + +void spi_cs_deactivate(struct spi_slave *slave) +{ + at91_set_pio_output(AT91_PIO_PORTC, 3, 1); +} + +static void sama5d4_xplained_spi0_hw_init(void) +{ + at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* SPI0_MISO */ + at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* SPI0_MOSI */ + at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* SPI0_SPCK */ + + at91_set_pio_output(AT91_PIO_PORTC, 3, 1); /* SPI0_CS0 */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_SPI0); +} +#endif /* CONFIG_ATMEL_SPI */ + +#ifdef CONFIG_NAND_ATMEL +static void sama5d4_xplained_nand_hw_init(void) +{ + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + + at91_periph_clk_enable(ATMEL_ID_SMC); + + /* Configure SMC CS3 for NAND */ + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1), + &smc->cs[3].setup); + writel(AT91_SMC_PULSE_NWE(2) | AT91_SMC_PULSE_NCS_WR(3) | + AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(3), + &smc->cs[3].pulse); + writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), + &smc->cs[3].cycle); + writel(AT91_SMC_TIMINGS_TCLR(2) | AT91_SMC_TIMINGS_TADL(7) | + AT91_SMC_TIMINGS_TAR(2) | AT91_SMC_TIMINGS_TRR(3) | + AT91_SMC_TIMINGS_TWB(7) | AT91_SMC_TIMINGS_RBNSEL(3)| + AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | + AT91_SMC_MODE_DBW_8 | + AT91_SMC_MODE_TDF_CYCLE(3), + &smc->cs[3].mode); + + at91_set_a_periph(AT91_PIO_PORTC, 5, 0); /* D0 */ + at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* D1 */ + at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* D2 */ + at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* D3 */ + at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* D4 */ + at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* D5 */ + at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* D6 */ + at91_set_a_periph(AT91_PIO_PORTC, 12, 0); /* D7 */ + at91_set_a_periph(AT91_PIO_PORTC, 13, 0); /* RE */ + at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* WE */ + at91_set_a_periph(AT91_PIO_PORTC, 15, 1); /* NCS */ + at91_set_a_periph(AT91_PIO_PORTC, 16, 1); /* RDY */ + at91_set_a_periph(AT91_PIO_PORTC, 17, 1); /* ALE */ + at91_set_a_periph(AT91_PIO_PORTC, 18, 1); /* CLE */ +} +#endif + +#ifdef CONFIG_CMD_USB +static void sama5d4_xplained_usb_hw_init(void) +{ + at91_set_pio_output(AT91_PIO_PORTE, 11, 1); + at91_set_pio_output(AT91_PIO_PORTE, 14, 1); +} +#endif + +#ifdef CONFIG_LCD +vidinfo_t panel_info = { + .vl_col = 480, + .vl_row = 272, + .vl_clk = 9000, + .vl_sync = ATMEL_LCDC_INVLINE_NORMAL | ATMEL_LCDC_INVFRAME_NORMAL, + .vl_bpix = LCD_BPP, + .vl_bpox = LCD_OUTPUT_BPP, + .vl_tft = 1, + .vl_hsync_len = 41, + .vl_left_margin = 2, + .vl_right_margin = 2, + .vl_vsync_len = 11, + .vl_upper_margin = 2, + .vl_lower_margin = 2, + .mmio = ATMEL_BASE_LCDC, +}; + +/* No power up/down pin for the LCD pannel */ +void lcd_enable(void) { /* Empty! */ } +void lcd_disable(void) { /* Empty! */ } + +unsigned int has_lcdc(void) +{ + return 1; +} + +static void sama5d4_xplained_lcd_hw_init(void) +{ + at91_set_a_periph(AT91_PIO_PORTA, 24, 0); /* LCDPWM */ + at91_set_a_periph(AT91_PIO_PORTA, 25, 0); /* LCDDISP */ + at91_set_a_periph(AT91_PIO_PORTA, 26, 0); /* LCDVSYNC */ + at91_set_a_periph(AT91_PIO_PORTA, 27, 0); /* LCDHSYNC */ + at91_set_a_periph(AT91_PIO_PORTA, 28, 0); /* LCDDOTCK */ + at91_set_a_periph(AT91_PIO_PORTA, 29, 0); /* LCDDEN */ + + at91_set_a_periph(AT91_PIO_PORTA, 0, 0); /* LCDD0 */ + at91_set_a_periph(AT91_PIO_PORTA, 1, 0); /* LCDD1 */ + at91_set_a_periph(AT91_PIO_PORTA, 2, 0); /* LCDD2 */ + at91_set_a_periph(AT91_PIO_PORTA, 3, 0); /* LCDD3 */ + at91_set_a_periph(AT91_PIO_PORTA, 4, 0); /* LCDD4 */ + at91_set_a_periph(AT91_PIO_PORTA, 5, 0); /* LCDD5 */ + at91_set_a_periph(AT91_PIO_PORTA, 6, 0); /* LCDD6 */ + at91_set_a_periph(AT91_PIO_PORTA, 7, 0); /* LCDD7 */ + + at91_set_a_periph(AT91_PIO_PORTA, 8, 0); /* LCDD9 */ + at91_set_a_periph(AT91_PIO_PORTA, 9, 0); /* LCDD8 */ + at91_set_a_periph(AT91_PIO_PORTA, 10, 0); /* LCDD10 */ + at91_set_a_periph(AT91_PIO_PORTA, 11, 0); /* LCDD11 */ + at91_set_a_periph(AT91_PIO_PORTA, 12, 0); /* LCDD12 */ + at91_set_a_periph(AT91_PIO_PORTA, 13, 0); /* LCDD13 */ + at91_set_a_periph(AT91_PIO_PORTA, 14, 0); /* LCDD14 */ + at91_set_a_periph(AT91_PIO_PORTA, 15, 0); /* LCDD15 */ + + at91_set_a_periph(AT91_PIO_PORTA, 16, 0); /* LCDD16 */ + at91_set_a_periph(AT91_PIO_PORTA, 17, 0); /* LCDD17 */ + at91_set_a_periph(AT91_PIO_PORTA, 18, 0); /* LCDD18 */ + at91_set_a_periph(AT91_PIO_PORTA, 19, 0); /* LCDD19 */ + at91_set_a_periph(AT91_PIO_PORTA, 20, 0); /* LCDD20 */ + at91_set_a_periph(AT91_PIO_PORTA, 21, 0); /* LCDD21 */ + at91_set_a_periph(AT91_PIO_PORTA, 22, 0); /* LCDD22 */ + at91_set_a_periph(AT91_PIO_PORTA, 23, 0); /* LCDD23 */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_LCDC); +} + +#ifdef CONFIG_LCD_INFO +void lcd_show_board_info(void) +{ + ulong dram_size, nand_size; + int i; + char temp[32]; + + lcd_printf("2014 ATMEL Corp\n"); + lcd_printf("%s CPU at %s MHz\n", get_cpu_name(), + strmhz(temp, get_cpu_clk_rate())); + + dram_size = 0; + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) + dram_size += gd->bd->bi_dram[i].size; + + nand_size = 0; +#ifdef CONFIG_NAND_ATMEL + for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) + nand_size += nand_info[i].size; +#endif + lcd_printf("%ld MB SDRAM, %ld MB NAND\n", + dram_size >> 20, nand_size >> 20); +} +#endif /* CONFIG_LCD_INFO */ + +#endif /* CONFIG_LCD */ + +#ifdef CONFIG_GENERIC_ATMEL_MCI +void sama5d4_xplained_mci1_hw_init(void) +{ + at91_set_c_periph(AT91_PIO_PORTE, 19, 1); /* MCI1 CDA */ + at91_set_c_periph(AT91_PIO_PORTE, 20, 1); /* MCI1 DA0 */ + at91_set_c_periph(AT91_PIO_PORTE, 21, 1); /* MCI1 DA1 */ + at91_set_c_periph(AT91_PIO_PORTE, 22, 1); /* MCI1 DA2 */ + at91_set_c_periph(AT91_PIO_PORTE, 23, 1); /* MCI1 DA3 */ + at91_set_c_periph(AT91_PIO_PORTE, 18, 0); /* MCI1 CLK */ + + /* + * As the mci io internal pull down is too strong, so if the io needs + * external pull up, the pull up resistor will be very small, if so + * the power consumption will increase, so disable the interanl pull + * down to save the power. + */ + at91_set_pio_pulldown(AT91_PIO_PORTE, 18, 0); + at91_set_pio_pulldown(AT91_PIO_PORTE, 19, 0); + at91_set_pio_pulldown(AT91_PIO_PORTE, 20, 0); + at91_set_pio_pulldown(AT91_PIO_PORTE, 21, 0); + at91_set_pio_pulldown(AT91_PIO_PORTE, 22, 0); + at91_set_pio_pulldown(AT91_PIO_PORTE, 23, 0); + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_MCI1); +} + +int board_mmc_init(bd_t *bis) +{ + return atmel_mci_init((void *)ATMEL_BASE_MCI1); +} +#endif /* CONFIG_GENERIC_ATMEL_MCI */ + +#ifdef CONFIG_MACB +void sama5d4_xplained_macb0_hw_init(void) +{ + at91_set_a_periph(AT91_PIO_PORTB, 0, 0); /* ETXCK_EREFCK */ + at91_set_a_periph(AT91_PIO_PORTB, 6, 0); /* ERXDV */ + at91_set_a_periph(AT91_PIO_PORTB, 8, 0); /* ERX0 */ + at91_set_a_periph(AT91_PIO_PORTB, 9, 0); /* ERX1 */ + at91_set_a_periph(AT91_PIO_PORTB, 7, 0); /* ERXER */ + at91_set_a_periph(AT91_PIO_PORTB, 2, 0); /* ETXEN */ + at91_set_a_periph(AT91_PIO_PORTB, 12, 0); /* ETX0 */ + at91_set_a_periph(AT91_PIO_PORTB, 13, 0); /* ETX1 */ + at91_set_a_periph(AT91_PIO_PORTB, 17, 0); /* EMDIO */ + at91_set_a_periph(AT91_PIO_PORTB, 16, 0); /* EMDC */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_GMAC0); +} +#endif + +static void sama5d4_xplained_serial3_hw_init(void) +{ + at91_set_b_periph(AT91_PIO_PORTE, 17, 1); /* TXD3 */ + at91_set_b_periph(AT91_PIO_PORTE, 16, 0); /* RXD3 */ + + /* Enable clock */ + at91_periph_clk_enable(ATMEL_ID_USART3); +} + +int board_early_init_f(void) +{ + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOC); + at91_periph_clk_enable(ATMEL_ID_PIOD); + at91_periph_clk_enable(ATMEL_ID_PIOE); + + sama5d4_xplained_serial3_hw_init(); + + return 0; +} + +int board_init(void) +{ + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + +#ifdef CONFIG_ATMEL_SPI + sama5d4_xplained_spi0_hw_init(); +#endif +#ifdef CONFIG_NAND_ATMEL + sama5d4_xplained_nand_hw_init(); +#endif +#ifdef CONFIG_GENERIC_ATMEL_MCI + sama5d4_xplained_mci1_hw_init(); +#endif +#ifdef CONFIG_MACB + sama5d4_xplained_macb0_hw_init(); +#endif +#ifdef CONFIG_LCD + sama5d4_xplained_lcd_hw_init(); +#endif +#ifdef CONFIG_CMD_USB + sama5d4_xplained_usb_hw_init(); +#endif + + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + return 0; +} + +int board_eth_init(bd_t *bis) +{ + int rc = 0; + +#ifdef CONFIG_MACB + rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00); +#endif + + return rc; +} diff --git a/configs/sama5d4_xplained_mmc_defconfig b/configs/sama5d4_xplained_mmc_defconfig new file mode 100644 index 0000000000..3720f3cfb4 --- /dev/null +++ b/configs/sama5d4_xplained_mmc_defconfig @@ -0,0 +1,3 @@ +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_MMC" ++S:CONFIG_ARM=y ++S:CONFIG_TARGET_SAMA5D4_XPLAINED=y diff --git a/configs/sama5d4_xplained_nandflash_defconfig b/configs/sama5d4_xplained_nandflash_defconfig new file mode 100644 index 0000000000..5e13da7908 --- /dev/null +++ b/configs/sama5d4_xplained_nandflash_defconfig @@ -0,0 +1,3 @@ +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_NANDFLASH" ++S:CONFIG_ARM=y ++S:CONFIG_TARGET_SAMA5D4_XPLAINED=y diff --git a/configs/sama5d4_xplained_spiflash_defconfig b/configs/sama5d4_xplained_spiflash_defconfig new file mode 100644 index 0000000000..3a4607c676 --- /dev/null +++ b/configs/sama5d4_xplained_spiflash_defconfig @@ -0,0 +1,3 @@ +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_SERIALFLASH" ++S:CONFIG_ARM=y ++S:CONFIG_TARGET_SAMA5D4_XPLAINED=y diff --git a/include/configs/sama5d4_xplained.h b/include/configs/sama5d4_xplained.h new file mode 100644 index 0000000000..104edef102 --- /dev/null +++ b/include/configs/sama5d4_xplained.h @@ -0,0 +1,216 @@ +/* + * Configuration settings for the SAMA5D4 Xplained ultra board. + * + * Copyright (C) 2014 Atmel + * Bo Shen <voice.shen@atmel.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/hardware.h> + +#define CONFIG_SYS_TEXT_BASE 0x26f00000 + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ + +#define CONFIG_ARCH_CPU_INIT + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_CMD_BOOTZ +#define CONFIG_OF_LIBFDT /* Device Tree support */ + +#define CONFIG_SYS_GENERIC_BOARD + +/* general purpose I/O */ +#define CONFIG_AT91_GPIO + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_USART3 +#define CONFIG_USART_ID ATMEL_ID_USART3 + +#define CONFIG_BOOTDELAY 3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* No NOR flash */ +#define CONFIG_SYS_NO_FLASH + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_LOADS +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_SETEXPR + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS +#define CONFIG_SYS_SDRAM_SIZE 0x20000000 + +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ + +/* SerialFlash */ +#define CONFIG_CMD_SF + +#ifdef CONFIG_CMD_SF +#define CONFIG_ATMEL_SPI +#define CONFIG_ATMEL_SPI0 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ATMEL +#define CONFIG_SF_DEFAULT_BUS 0 +#define CONFIG_SF_DEFAULT_CS 0 +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#endif + +/* NAND flash */ +#define CONFIG_CMD_NAND + +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +/* our ALE is AD21 */ +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +/* our CLE is AD22 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ONFI_DETECTION +/* PMECC & PMERRLOC */ +#define CONFIG_ATMEL_NAND_HWECC +#define CONFIG_ATMEL_NAND_HW_PMECC +#endif + +/* MMC */ +#define CONFIG_CMD_MMC + +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#define ATMEL_BASE_MMCI ATMEL_BASE_MCI1 +#endif + +/* USB */ +#define CONFIG_CMD_USB + +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_ATMEL +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 +#define CONFIG_USB_STORAGE +#endif + +#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* Ethernet Hardware */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_MACB_SEARCH_PHY + +/* LCD */ +/* #define CONFIG_LCD */ +#ifdef CONFIG_LCD +#define LCD_BPP LCD_COLOR16 +#define LCD_OUTPUT_BPP 24 +#define CONFIG_LCD_LOGO +#define CONFIG_LCD_INFO +#define CONFIG_LCD_INFO_BELOW_LOGO +#define CONFIG_SYS_WHITE_ON_BLACK +#define CONFIG_ATMEL_HLCD +#define CONFIG_ATMEL_LCD_RGB565 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#endif + +#ifdef CONFIG_SYS_USE_SERIALFLASH +/* bootstrap + u-boot + env + linux in serial flash */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS +#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS +#define CONFIG_ENV_OFFSET 0x10000 +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_SECT_SIZE 0x1000 +#define CONFIG_BOOTCOMMAND "sf probe 0; " \ + "sf read 0x21000000 0xa0000 0x60000; " \ + "sf read 0x22000000 0x100000 0x300000; " \ + "bootz 0x22000000 - 0x21000000" +#elif CONFIG_SYS_USE_NANDFLASH +/* bootstrap + u-boot + env in nandflash */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0xc0000 +#define CONFIG_ENV_OFFSET_REDUND 0x100000 +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \ + "nand read 0x22000000 0x200000 0x600000;" \ + "bootz 0x22000000 - 0x21000000" +#elif CONFIG_SYS_USE_MMC +/* bootstrap + u-boot + env in sd card */ +#define CONFIG_ENV_IS_IN_FAT +#define CONFIG_FAT_WRITE +#define FAT_ENV_INTERFACE "mmc" +/* + * We don't specify the part number, if device 0 has partition table, it means + * the first partition; it no partition table, then take whole device as a + * FAT file system. + */ +#define FAT_ENV_DEVICE_AND_PART "0" +#define FAT_ENV_FILE "uboot.env" +#define CONFIG_ENV_SIZE 0x4000 +#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 at91-sama5d4_xplained.dtb; " \ + "fatload mmc 0:1 0x22000000 zImage; " \ + "bootz 0x22000000 - 0x21000000" +#endif + +#ifdef CONFIG_SYS_USE_MMC +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ + "root=/dev/mmcblk0p2 rw rootwait" +#else +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ + "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ + "256K(env),256k(evn_redundent),256k(spare)," \ + "512k(dtb),6M(kernel)ro,-(rootfs) " \ + "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs" +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +#endif |