summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--arch/arm/dts/Makefile1
-rw-r--r--arch/arm/dts/meson-g12-common.dtsi13
-rw-r--r--arch/arm/dts/meson-g12.dtsi32
-rw-r--r--arch/arm/dts/meson-g12b-khadas-vim3.dtsi22
-rw-r--r--arch/arm/dts/meson-g12b-s922x.dtsi15
-rw-r--r--arch/arm/dts/meson-g12b.dtsi22
-rw-r--r--arch/arm/dts/meson-khadas-vim3.dtsi4
-rw-r--r--arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi13
-rw-r--r--arch/arm/dts/meson-sm1-odroid-c4.dts402
-rw-r--r--arch/arm/dts/meson-sm1-sei610.dts2
-rw-r--r--arch/arm/dts/meson-sm1.dtsi24
-rw-r--r--board/amlogic/odroid-n2/MAINTAINERS9
-rw-r--r--board/amlogic/odroid-n2/Makefile6
-rw-r--r--board/amlogic/odroid-n2/odroid-n2.c49
-rw-r--r--board/amlogic/w400/MAINTAINERS2
-rw-r--r--configs/odroid-c4_defconfig62
-rw-r--r--configs/odroid-n2_defconfig2
-rw-r--r--doc/board/amlogic/index.rst3
-rw-r--r--doc/board/amlogic/odroid-c4.rst134
19 files changed, 777 insertions, 40 deletions
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index d345e30f35..d839cb49b3 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -163,6 +163,7 @@ dtb-$(CONFIG_ARCH_MESON) += \
meson-g12b-odroid-n2.dtb \
meson-g12b-a311d-khadas-vim3.dtb \
meson-sm1-khadas-vim3l.dtb \
+ meson-sm1-odroid-c4.dtb \
meson-sm1-sei610.dtb
dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
tegra20-medcom-wide.dtb \
diff --git a/arch/arm/dts/meson-g12-common.dtsi b/arch/arm/dts/meson-g12-common.dtsi
index 0882ea215b..593a006f4b 100644
--- a/arch/arm/dts/meson-g12-common.dtsi
+++ b/arch/arm/dts/meson-g12-common.dtsi
@@ -250,6 +250,17 @@
};
};
+ acodec: audio-controller@32000 {
+ compatible = "amlogic,t9015";
+ reg = <0x0 0x32000 0x0 0x14>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "ACODEC";
+ clocks = <&clkc CLKID_AUDIO_CODEC>;
+ clock-names = "pclk";
+ resets = <&reset RESET_AUDIO_CODEC>;
+ status = "disabled";
+ };
+
periphs: bus@34400 {
compatible = "simple-bus";
reg = <0x0 0x34400 0x0 0x400>;
@@ -2319,7 +2330,7 @@
reg = <0x0 0xff400000 0x0 0x40000>;
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
- clock-names = "ddr";
+ clock-names = "otg";
phys = <&usb2_phy1>;
phy-names = "usb2-phy";
dr_mode = "peripheral";
diff --git a/arch/arm/dts/meson-g12.dtsi b/arch/arm/dts/meson-g12.dtsi
index 55d39020ec..6a1f4dcf64 100644
--- a/arch/arm/dts/meson-g12.dtsi
+++ b/arch/arm/dts/meson-g12.dtsi
@@ -343,6 +343,15 @@
status = "disabled";
};
+ toacodec: audio-controller@740 {
+ compatible = "amlogic,g12a-toacodec";
+ reg = <0x0 0x740 0x0 0x4>;
+ #sound-dai-cells = <1>;
+ sound-name-prefix = "TOACODEC";
+ resets = <&clkc_audio AUD_RESET_TOACODEC>;
+ status = "disabled";
+ };
+
tohdmitx: audio-controller@744 {
compatible = "amlogic,g12a-tohdmitx";
reg = <0x0 0x744 0x0 0x4>;
@@ -354,29 +363,6 @@
};
};
-&cpu_thermal {
- cooling-maps {
- map0 {
- trip = <&cpu_passive>;
- cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
- <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
- <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
- <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
- <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
- <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
- map1 {
- trip = <&cpu_hot>;
- cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
- <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
- <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
- <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
- <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
- <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
- };
-};
-
&ethmac {
power-domains = <&pwrc PWRC_G12A_ETH_ID>;
};
diff --git a/arch/arm/dts/meson-g12b-khadas-vim3.dtsi b/arch/arm/dts/meson-g12b-khadas-vim3.dtsi
index c33e85fbda..224c890d32 100644
--- a/arch/arm/dts/meson-g12b-khadas-vim3.dtsi
+++ b/arch/arm/dts/meson-g12b-khadas-vim3.dtsi
@@ -51,11 +51,11 @@
sound {
compatible = "amlogic,axg-sound-card";
model = "G12B-KHADAS-VIM3";
- audio-aux-devs = <&tdmout_b>;
- audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
- "TDMOUT_B IN 1", "FRDDR_B OUT 1",
- "TDMOUT_B IN 2", "FRDDR_C OUT 1",
- "TDM_B Playback", "TDMOUT_B OUT";
+ audio-aux-devs = <&tdmout_a>;
+ audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0",
+ "TDMOUT_A IN 1", "FRDDR_B OUT 0",
+ "TDMOUT_A IN 2", "FRDDR_C OUT 0",
+ "TDM_A Playback", "TDMOUT_A OUT";
assigned-clocks = <&clkc CLKID_MPLL2>,
<&clkc CLKID_MPLL0>,
@@ -80,7 +80,7 @@
/* 8ch hdmi interface */
dai-link-3 {
- sound-dai = <&tdmif_b>;
+ sound-dai = <&tdmif_a>;
dai-format = "i2s";
dai-tdm-slot-tx-mask-0 = <1 1>;
dai-tdm-slot-tx-mask-1 = <1 1>;
@@ -89,7 +89,7 @@
mclk-fs = <256>;
codec {
- sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>;
};
};
@@ -154,6 +154,10 @@
clock-latency = <50000>;
};
+&frddr_a {
+ status = "okay";
+};
+
&frddr_b {
status = "okay";
};
@@ -178,11 +182,11 @@
status = "okay";
};
-&tdmif_b {
+&tdmif_a {
status = "okay";
};
-&tdmout_b {
+&tdmout_a {
status = "okay";
};
diff --git a/arch/arm/dts/meson-g12b-s922x.dtsi b/arch/arm/dts/meson-g12b-s922x.dtsi
index 046cc332d0..1e5d0ee5d5 100644
--- a/arch/arm/dts/meson-g12b-s922x.dtsi
+++ b/arch/arm/dts/meson-g12b-s922x.dtsi
@@ -65,6 +65,11 @@
opp-hz = /bits/ 64 <1896000000>;
opp-microvolt = <981000>;
};
+
+ opp-1992000000 {
+ opp-hz = /bits/ 64 <1992000000>;
+ opp-microvolt = <1001000>;
+ };
};
cpub_opp_table_1: opp-table-1 {
@@ -120,5 +125,15 @@
opp-hz = /bits/ 64 <1704000000>;
opp-microvolt = <891000>;
};
+
+ opp-1800000000 {
+ opp-hz = /bits/ 64 <1800000000>;
+ opp-microvolt = <981000>;
+ };
+
+ opp-1908000000 {
+ opp-hz = /bits/ 64 <1908000000>;
+ opp-microvolt = <1022000>;
+ };
};
};
diff --git a/arch/arm/dts/meson-g12b.dtsi b/arch/arm/dts/meson-g12b.dtsi
index 6dbc396804..9b8548e5f6 100644
--- a/arch/arm/dts/meson-g12b.dtsi
+++ b/arch/arm/dts/meson-g12b.dtsi
@@ -113,3 +113,25 @@
compatible = "amlogic,g12b-clkc";
};
+&cpu_thermal {
+ cooling-maps {
+ map0 {
+ trip = <&cpu_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
diff --git a/arch/arm/dts/meson-khadas-vim3.dtsi b/arch/arm/dts/meson-khadas-vim3.dtsi
index 094ecf2222..1ef1e3672b 100644
--- a/arch/arm/dts/meson-khadas-vim3.dtsi
+++ b/arch/arm/dts/meson-khadas-vim3.dtsi
@@ -39,13 +39,13 @@
leds {
compatible = "gpio-leds";
- white {
+ led-white {
label = "vim3:white:sys";
gpios = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
};
- red {
+ led-red {
label = "vim3:red";
gpios = <&gpio_expander 5 GPIO_ACTIVE_LOW>;
};
diff --git a/arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi b/arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi
new file mode 100644
index 0000000000..2a8f0545b1
--- /dev/null
+++ b/arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12-common-u-boot.dtsi"
+
+&ethmac {
+ snps,reset-gpio = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ snps,reset-delays-us = <0 10000 1000000>;
+ snps,reset-active-low;
+};
diff --git a/arch/arm/dts/meson-sm1-odroid-c4.dts b/arch/arm/dts/meson-sm1-odroid-c4.dts
new file mode 100644
index 0000000000..00d90b30f8
--- /dev/null
+++ b/arch/arm/dts/meson-sm1-odroid-c4.dts
@@ -0,0 +1,402 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Dongjin Kim <tobetter@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "hardkernel,odroid-c4", "amlogic,sm1";
+ model = "Hardkernel ODROID-C4";
+
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = &ethmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ panic-indicator;
+ };
+ };
+
+ tflash_vdd: regulator-tflash_vdd {
+ compatible = "regulator-fixed";
+
+ regulator-name = "TFLASH_VDD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ tf_io: gpio-regulator-tf_io {
+ compatible = "regulator-gpio";
+
+ regulator-name = "TF_IO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0>,
+ <1800000 1>;
+ };
+
+ flash_1v8: regulator-flash_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "FLASH_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ main_12v: regulator-main_12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&main_12v>;
+ };
+
+ vcc_1v8: regulator-vcc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ vddcpu: regulator-vddcpu {
+ /*
+ * MP8756GD Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&main_12v>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ hub_5v: regulator-hub_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "HUB_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ /* Connected to the Hub CHIPENABLE, LOW sets low power state */
+ gpio = <&gpio GPIOH_4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_pwr_en: regulator-usb_pwr_en {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR_EN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ /* Connected to the microUSB port power enable */
+ gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vddao_1v8: regulator-vddao_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-always-on;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU1_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu2 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU2_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu3 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU3_CLK>;
+ clock-latency = <50000>;
+};
+
+&ext_mdio {
+ external_phy: ethernet-phy@0 {
+ /* Realtek RTL8211F (0x001cc916) */
+ reg = <0>;
+ max-speed = <1000>;
+
+ interrupt-parent = <&gpio_intc>;
+ /* MAC_INTR on GPIOZ_14 */
+ interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&ethmac {
+ pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&external_phy>;
+ amlogic,tx-delay-ns = <2>;
+};
+
+&gpio {
+ gpio-line-names =
+ /* GPIOZ */
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ /* GPIOH */
+ "", "", "", "", "",
+ "PIN_36", /* GPIOH_5 */
+ "PIN_26", /* GPIOH_6 */
+ "PIN_32", /* GPIOH_7 */
+ "",
+ /* BOOT */
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ /* GPIOC */
+ "", "", "", "", "", "", "", "",
+ /* GPIOA */
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "",
+ "PIN_27", /* GPIOA_14 */
+ "PIN_28", /* GPIOA_15 */
+ /* GPIOX */
+ "PIN_16", /* GPIOX_0 */
+ "PIN_18", /* GPIOX_1 */
+ "PIN_22", /* GPIOX_2 */
+ "PIN_11", /* GPIOX_3 */
+ "PIN_13", /* GPIOX_4 */
+ "PIN_7", /* GPIOX_5 */
+ "PIN_33", /* GPIOX_6 */
+ "PIN_15", /* GPIOX_7 */
+ "PIN_19", /* GPIOX_8 */
+ "PIN_21", /* GPIOX_9 */
+ "PIN_24", /* GPIOX_10 */
+ "PIN_23", /* GPIOX_11 */
+ "PIN_8", /* GPIOX_12 */
+ "PIN_10", /* GPIOX_13 */
+ "PIN_29", /* GPIOX_14 */
+ "PIN_31", /* GPIOX_15 */
+ "PIN_12", /* GPIOX_16 */
+ "PIN_3", /* GPIOX_17 */
+ "PIN_5", /* GPIOX_18 */
+ "PIN_35"; /* GPIOX_19 */
+
+ /*
+ * WARNING: The USB Hub on the Odroid-C4 needs a reset signal
+ * to be turned high in order to be detected by the USB Controller
+ * This signal should be handled by a USB specific power sequence
+ * in order to reset the Hub when USB bus is powered down.
+ */
+ usb-hub {
+ gpio-hog;
+ gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-hub-reset";
+ };
+};
+
+&gpio_ao {
+ gpio-line-names =
+ /* GPIOAO */
+ "", "", "", "",
+ "PIN_47", /* GPIOAO_4 */
+ "", "",
+ "PIN_45", /* GPIOAO_7 */
+ "PIN_46", /* GPIOAO_8 */
+ "PIN_44", /* GPIOAO_9 */
+ "PIN_42", /* GPIOAO_10 */
+ "",
+ /* GPIOE */
+ "", "", "";
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+ linux,rc-map-name = "rc-odroid";
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
+&saradc {
+ status = "okay";
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <200000000>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&tflash_vdd>;
+ vqmmc-supply = <&tf_io>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&flash_1v8>;
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+ phy-supply = <&vcc_5v>;
+};
+
+&usb2_phy1 {
+ /* Enable the hub which is connected to this port */
+ phy-supply = <&hub_5v>;
+};
diff --git a/arch/arm/dts/meson-sm1-sei610.dts b/arch/arm/dts/meson-sm1-sei610.dts
index dfb2438851..5ab139a34c 100644
--- a/arch/arm/dts/meson-sm1-sei610.dts
+++ b/arch/arm/dts/meson-sm1-sei610.dts
@@ -104,7 +104,7 @@
leds {
compatible = "gpio-leds";
- bluetooth {
+ led-bluetooth {
label = "sei610:blue:bt";
gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
default-state = "off";
diff --git a/arch/arm/dts/meson-sm1.dtsi b/arch/arm/dts/meson-sm1.dtsi
index d4ec735fb1..71317f5aad 100644
--- a/arch/arm/dts/meson-sm1.dtsi
+++ b/arch/arm/dts/meson-sm1.dtsi
@@ -56,6 +56,7 @@
reg = <0x0 0x0>;
enable-method = "psci";
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu1: cpu@1 {
@@ -64,6 +65,7 @@
reg = <0x0 0x1>;
enable-method = "psci";
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu2: cpu@2 {
@@ -72,6 +74,7 @@
reg = <0x0 0x2>;
enable-method = "psci";
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu3: cpu@3 {
@@ -80,6 +83,7 @@
reg = <0x0 0x3>;
enable-method = "psci";
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
l2: l2-cache0 {
@@ -466,6 +470,26 @@
compatible = "amlogic,sm1-clkc";
};
+&cpu_thermal {
+ cooling-maps {
+ map0 {
+ trip = <&cpu_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
&ethmac {
power-domains = <&pwrc PWRC_SM1_ETH_ID>;
};
diff --git a/board/amlogic/odroid-n2/MAINTAINERS b/board/amlogic/odroid-n2/MAINTAINERS
new file mode 100644
index 0000000000..77f7746346
--- /dev/null
+++ b/board/amlogic/odroid-n2/MAINTAINERS
@@ -0,0 +1,9 @@
+ODROID-N2
+M: Neil Armstrong <narmstrong@baylibre.com>
+S: Maintained
+L: u-boot-amlogic@groups.io
+F: board/amlogic/odroid-n2/
+F: configs/odroid-n2_defconfig
+F: configs/odroid-c4_defconfig
+F: doc/board/amlogic/odroid-n2.rst
+F: doc/board/amlogic/odroid-c4.rst
diff --git a/board/amlogic/odroid-n2/Makefile b/board/amlogic/odroid-n2/Makefile
new file mode 100644
index 0000000000..68e4e2a828
--- /dev/null
+++ b/board/amlogic/odroid-n2/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2020 BayLibre, SAS
+# Author: Neil Armstrong <narmstrong@baylibre.com>
+
+obj-y := odroid-n2.o
diff --git a/board/amlogic/odroid-n2/odroid-n2.c b/board/amlogic/odroid-n2/odroid-n2.c
new file mode 100644
index 0000000000..caf7fd6810
--- /dev/null
+++ b/board/amlogic/odroid-n2/odroid-n2.c
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <env.h>
+#include <init.h>
+#include <net.h>
+#include <asm/io.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+
+#define EFUSE_MAC_OFFSET 20
+#define EFUSE_MAC_SIZE 12
+#define MAC_ADDR_LEN 6
+
+int misc_init_r(void)
+{
+ u8 mac_addr[MAC_ADDR_LEN];
+ char efuse_mac_addr[EFUSE_MAC_SIZE], tmp[3];
+ ssize_t len;
+
+ meson_eth_init(PHY_INTERFACE_MODE_RGMII, 0);
+
+ if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+ len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+ efuse_mac_addr, EFUSE_MAC_SIZE);
+ if (len != EFUSE_MAC_SIZE)
+ return 0;
+
+ /* MAC is stored in ASCII format, 1bytes = 2characters */
+ for (int i = 0; i < 6; i++) {
+ tmp[0] = efuse_mac_addr[i * 2];
+ tmp[1] = efuse_mac_addr[i * 2 + 1];
+ tmp[2] = '\0';
+ mac_addr[i] = simple_strtoul(tmp, NULL, 16);
+ }
+
+ if (is_valid_ethaddr(mac_addr))
+ eth_env_set_enetaddr("ethaddr", mac_addr);
+ else
+ meson_generate_serial_ethaddr();
+ }
+
+ return 0;
+}
diff --git a/board/amlogic/w400/MAINTAINERS b/board/amlogic/w400/MAINTAINERS
index 5e837cfaef..a1b0ac8636 100644
--- a/board/amlogic/w400/MAINTAINERS
+++ b/board/amlogic/w400/MAINTAINERS
@@ -5,8 +5,6 @@ L: u-boot-amlogic@groups.io
F: board/amlogic/w400/
F: configs/khadas-vim3_defconfig
F: configs/khadas-vim3l_defconfig
-F: configs/odroid-n2_defconfig
F: doc/board/amlogic/w400.rst
F: doc/board/amlogic/khadas-vim3.rst
F: doc/board/amlogic/khadas-vim3l.rst
-F: doc/board/amlogic/odroid-n2.rst
diff --git a/configs/odroid-c4_defconfig b/configs/odroid-c4_defconfig
new file mode 100644
index 0000000000..db9271916e
--- /dev/null
+++ b/configs/odroid-c4_defconfig
@@ -0,0 +1,62 @@
+CONFIG_ARM=y
+CONFIG_SYS_BOARD="odroid-n2"
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_ENV_SIZE=0x2000
+CONFIG_DM_GPIO=y
+CONFIG_MESON_G12A=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEBUG_UART_BASE=0xff803000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" odroid-c4"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_MISC_INIT_R=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-sm1-odroid-c4"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_MESON_G12A_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_G12A=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MESON_EE_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_DWC3_MESON_G12A=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_DM_VIDEO=y
+CONFIG_VIDEO_MESON=y
+CONFIG_VIDEO_DT_SIMPLEFB=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/configs/odroid-n2_defconfig b/configs/odroid-n2_defconfig
index e0cc6e3729..063809416e 100644
--- a/configs/odroid-n2_defconfig
+++ b/configs/odroid-n2_defconfig
@@ -1,5 +1,5 @@
CONFIG_ARM=y
-CONFIG_SYS_BOARD="w400"
+CONFIG_SYS_BOARD="odroid-n2"
CONFIG_ARCH_MESON=y
CONFIG_SYS_TEXT_BASE=0x01000000
CONFIG_ENV_SIZE=0x2000
diff --git a/doc/board/amlogic/index.rst b/doc/board/amlogic/index.rst
index 3730419167..0e2f8c9aad 100644
--- a/doc/board/amlogic/index.rst
+++ b/doc/board/amlogic/index.rst
@@ -17,7 +17,7 @@ This matrix concerns the actual source code version.
+===============================+===========+==============+==============+============+============+=============+==============+
| Boards | Odroid-C2 | P212 | Khadas VIM2 | S400 | U200 | Odroid-N2 | SEI610 |
| | Nanopi-K2 | Khadas-VIM | Libretech-PC | | SEI510 | Khadas-VIM3 | Khadas-VIM3L |
-| | P200 | LibreTech-CC | | | | | |
+| | P200 | LibreTech-CC | | | | | Odroid-C4 |
| | P201 | LibreTech-AC | | | | | |
+-------------------------------+-----------+--------------+--------------+------------+------------+-------------+--------------+
| UART | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
@@ -83,6 +83,7 @@ Board Documentation
libretech-cc
nanopi-k2
odroid-c2
+ odroid-c4
odroid-n2
p200
p201
diff --git a/doc/board/amlogic/odroid-c4.rst b/doc/board/amlogic/odroid-c4.rst
new file mode 100644
index 0000000000..5a5a8688b8
--- /dev/null
+++ b/doc/board/amlogic/odroid-c4.rst
@@ -0,0 +1,134 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for ODROID-C4
+====================
+
+ODROID-C4 is a single board computer manufactured by Hardkernel
+Co. Ltd with the following specifications:
+
+ - Amlogic S905X3 Arm Cortex-A55 quad-core SoC
+ - 4GB DDR4 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.1 display
+ - 40-pin GPIO header
+ - 4x USB 3.0 Host
+ - 1x USB 2.0 Host/OTG (micro)
+ - eMMC, microSD
+ - UART serial
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+U-Boot compilation
+------------------
+
+.. code-block:: bash
+
+ $ export CROSS_COMPILE=aarch64-none-elf-
+ $ make odroid-c4_defconfig
+ $ make
+
+Image creation
+--------------
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+.. code-block:: bash
+
+ $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ $ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ $ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ $ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+
+ $ DIR=odroid-c4
+ $ git clone --depth 1 \
+ https://github.com/hardkernel/u-boot.git -b odroidg12-v2015.01 \
+ $DIR
+
+ $ cd odroid-c4
+ $ make odroidc4_defconfig
+ $ make
+ $ export UBOOTDIR=$PWD
+
+Go back to mainline U-Boot source tree then :
+
+.. code-block:: bash
+
+ $ mkdir fip
+
+ $ wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
+ $ cp $UBOOTDIR/build/scp_task/bl301.bin fip/
+ $ cp $UBOOTDIR/build/board/hardkernel/odroidc4/firmware/acs.bin fip/
+ $ cp $UBOOTDIR/fip/g12a/bl2.bin fip/
+ $ cp $UBOOTDIR/fip/g12a/bl30.bin fip/
+ $ cp $UBOOTDIR/fip/g12a/bl31.img fip/
+ $ cp $UBOOTDIR/fip/g12a/ddr3_1d.fw fip/
+ $ cp $UBOOTDIR/fip/g12a/ddr4_1d.fw fip/
+ $ cp $UBOOTDIR/fip/g12a/ddr4_2d.fw fip/
+ $ cp $UBOOTDIR/fip/g12a/diag_lpddr4.fw fip/
+ $ cp $UBOOTDIR/fip/g12a/lpddr3_1d.fw fip/
+ $ cp $UBOOTDIR/fip/g12a/lpddr4_1d.fw fip/
+ $ cp $UBOOTDIR/fip/g12a/lpddr4_2d.fw fip/
+ $ cp $UBOOTDIR/fip/g12a/piei.fw fip/
+ $ cp $UBOOTDIR/fip/g12a/aml_ddr.fw fip/
+ $ cp u-boot.bin fip/bl33.bin
+
+ $ sh fip/blx_fix.sh \
+ fip/bl30.bin \
+ fip/zero_tmp \
+ fip/bl30_zero.bin \
+ fip/bl301.bin \
+ fip/bl301_zero.bin \
+ fip/bl30_new.bin \
+ bl30
+
+ $ sh fip/blx_fix.sh \
+ fip/bl2.bin \
+ fip/zero_tmp \
+ fip/bl2_zero.bin \
+ fip/acs.bin \
+ fip/bl21_zero.bin \
+ fip/bl2_new.bin \
+ bl2
+
+ $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \
+ --output fip/bl30_new.bin.g12a.enc \
+ --level v3
+ $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \
+ --output fip/bl30_new.bin.enc \
+ --level v3 --type bl30
+ $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \
+ --output fip/bl31.img.enc \
+ --level v3 --type bl31
+ $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \
+ --output fip/bl33.bin.enc \
+ --level v3 --type bl33 --compress lz4
+ $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \
+ --output fip/bl2.n.bin.sig
+ $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bootmk \
+ --output fip/u-boot.bin \
+ --bl2 fip/bl2.n.bin.sig \
+ --bl30 fip/bl30_new.bin.enc \
+ --bl31 fip/bl31.img.enc \
+ --bl33 fip/bl33.bin.enc \
+ --ddrfw1 fip/ddr4_1d.fw \
+ --ddrfw2 fip/ddr4_2d.fw \
+ --ddrfw3 fip/ddr3_1d.fw \
+ --ddrfw4 fip/piei.fw \
+ --ddrfw5 fip/lpddr4_1d.fw \
+ --ddrfw6 fip/lpddr4_2d.fw \
+ --ddrfw7 fip/diag_lpddr4.fw \
+ --ddrfw8 fip/aml_ddr.fw \
+ --ddrfw9 fip/lpddr3_1d.fw \
+ --level v3
+
+and then write the image to SD with:
+
+.. code-block:: bash
+
+ $ DEV=/dev/your_sd_device
+ $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444