diff options
Diffstat (limited to 'board/hisilicon/hikey960/README')
| -rw-r--r-- | board/hisilicon/hikey960/README | 247 |
1 files changed, 247 insertions, 0 deletions
diff --git a/board/hisilicon/hikey960/README b/board/hisilicon/hikey960/README new file mode 100644 index 0000000000..e1e330d535 --- /dev/null +++ b/board/hisilicon/hikey960/README @@ -0,0 +1,247 @@ +Introduction +============ + +HiKey960 is one of the 96Boards Consumer Edition board from HiSilicon. +The board/SoC has: - +* HiSilicon Kirin960 (HI3660) SoC with 4xCortex-A73 and 4xCortex-A53 +* ARM Mali G71 MP8 GPU +* 3GB LPDDR4 SDRAM +* 32GB UFS Flash Storage +* microSD +* 802.11a/b/g/n WiFi, Bluetooth + +More information about this board can be found in 96Boards website: +https://www.96boards.org/product/hikey960/ + +Currently the u-boot port supports: - +* SD card + +Compile from source +=================== + +First get all the sources + + > mkdir -p ~/hikey960/src ~/hikey960/bin + > cd ~/hikey960/src + > git clone https://github.com/ARM-software/arm-trusted-firmware + > git clone https://github.com/96boards-hikey/OpenPlatformPkg -b testing/hikey960_v1.3.4 + > git clone https://github.com/96boards-hikey/l-loader -b testing/hikey960_v1.2 + > wget http://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey960/release/config + > wget http://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey960/release/hisi-sec_usb_xloader.img + > wget http://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey960/release/hisi-sec_uce_boot.img + > wget http://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey960/release/sec_xloader.img + > wget http://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey960/release/recovery.bin + > wget http://snapshots.linaro.org/96boards/reference-platform/components/uefi-staging/latest/hikey960/release/hikey_idt + +Get the SCP_BL2 lpm3.img binary. It is shipped as part of the UEFI source. +The latest version can be obtained from the OpenPlatformPkg repo. + + > cp OpenPlatformPkg/Platforms/Hisilicon/HiKey960/Binary/lpm3.img ~/hikey960/bin/ + +Compile U-Boot +============== + + > cd ~/hikey960/src/u-boot + > make CROSS_COMPILE=aarch64-linux-gnu- hikey960_defconfig + > make CROSS_COMPILE=aarch64-linux-gnu- + > cp u-boot.bin ~/hikey960/bin/ + +Compile ARM Trusted Firmware (ATF) +================================== + + > cd ~/hikey960/src/arm-trusted-firmware + > make CROSS_COMPILE=aarch64-linux-gnu- all fip \ + SCP_BL2=~/hikey960/bin/lpm3.img \ + BL33=~/hikey960/bin/u-boot.bin DEBUG=1 PLAT=hikey960 + +Copy the resulting FIP binary + > cp build/hikey960/debug/fip.bin ~/hikey960/bin + +Compile l-loader +================ + > cd ~/hikey960/src/l-loader + > ln -sf ~/hikey960/src/arm-trusted-firmware/build/hikey960/debug/bl1.bin + > ln -sf ~/hikey960/src/arm-trusted-firmware/build/hikey960/debug/bl2.bin + > ln -sf ~/hikey960/src/arm-trusted-firmware/build/hikey960/debug/fip.bin + > ln -sf ~/hikey960/bin/u-boot.bin + > make hikey960 PTABLE_LST=linux-32g NS_BL1U=u-boot.bin + +Copy the resulting binaries + > cp *.img ~/hikey960/bin + > cp l-loader.bin ~/hikey960/bin + +These instructions are adapted from +https://github.com/ARM-software/arm-trusted-firmware/blob/master/docs/plat/hikey960.rst + +Setup Console +============= + +Install ser2net. Use telnet as the console since UEFI in recovery mode +output window fails to display in minicom. + + > sudo apt-get install ser2net + +Configure ser2net + + > sudo vi /etc/ser2net.conf + +Append one line for serial-over-USB in #ser2net.conf + + > 2004:telnet:0:/dev/ttyUSB0:115200 8DATABITS NONE 1STOPBIT banner + +Start ser2net + + > sudo killall ser2net + > sudo ser2net -u + +Open the console. + + > telnet localhost 2004 + +And you could open the console remotely, too. + +Flashing +======== + +1. Boot Hikey960 into recovery mode as per the below document: +https://github.com/96boards/documentation/blob/master/consumer/hikey/hikey960/installation/board-recovery.md + +Once Hikey960 is in recovery mode, flash the recovery binary: + + > cd ~/hikey960/src + > chmod +x ./hikey_idt + > sudo ./hikey_idt -c config -p /dev/ttyUSB1 + +Now move to the Hikey960 console and press `f` during UEFI boot. This +will allow the board to boot into fastboot mode. Once the board is in +fastboot mode, you should see the ID of the HiKey960 board using the +following command + + > sudo fastboot devices + +1ED3822A018E3372 fastboot + +3. Flash the images + +Now, the images can be flashed using fastboot: + + > sudo fastboot flash ptable ~/hikey960/bin/prm_ptable.img + > sudo fastboot flash xloader ~/hikey960/bin/sec_xloader.img + > sudo fastboot flash fastboot ~/hikey960/bin/l-loader.bin + > sudo fastboot flash fip ~/hikey960/bin/fip.bin + +4. Set the "Boot Mode" switch to OFF position for normal boot mode. +Then power on HiKey960 + +Observe the console traces using UART6 on the Low Speed Expansion header: + +NOTICE: BL2: v2.1(debug):v2.1-531-g3ee48f40 +NOTICE: BL2: Built : 18:15:58, Aug 2 2019 +INFO: BL2: Doing platform setup +INFO: UFS LUN0 contains 1024 blocks with 4096-byte size +INFO: UFS LUN1 contains 1024 blocks with 4096-byte size +INFO: UFS LUN2 contains 2048 blocks with 4096-byte size +INFO: UFS LUN3 contains 7805952 blocks with 4096-byte size +INFO: ufs: change power mode success +INFO: BL2: Loading image id 2 +INFO: Loading image id=2 at address 0x89c80000 +INFO: Image id=2 loaded: 0x89c80000 - 0x89cb5088 +INFO: BL2: Initiating SCP_BL2 transfer to SCP +INFO: BL2: SCP_BL2: 0x89c80000@0x35088 +INFO: BL2: SCP_BL2 HEAD: +INFO: BL2: SCP_BL2 0x7000 0x179 0x159 0x149 +INFO: BL2: SCP_BL2 0x189 0x18b 0x18d 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x18f +INFO: BL2: SCP_BL2 0x191 0x0 0x193 0x195 +INFO: BL2: SCP_BL2 0x18fd 0x18fd 0x18fd 0x18fd +INFO: BL2: SCP_BL2 0x18fd 0x18fd 0x18fd 0x18fd +INFO: BL2: SCP_BL2 0x18fd 0x18fd 0x18fd 0x18fd +INFO: BL2: SCP_BL2 0x4d454355 0x43494741 0x424d554e 0x21215245 +INFO: BL2: SCP_BL2 0x4a054904 0x42912000 0xf841bfbc 0xe7fa0b04 +INFO: BL2: SCP_BL2 0xb88cf000 0x3b18 0x3d1c 0x6809493e +INFO: BL2: SCP_BL2 0x4613680a 0x201f102 0xf0002a04 0x600a804c +INFO: BL2: SCP_BL2 0x204f04f 0xf203fb02 0xf102440a 0x60100204 +INFO: BL2: SCP_BL2 0x160f04f 0xf103fb01 0x68004834 0x61044408 +INFO: BL2: SCP_BL2 0x61866145 0xf8c061c7 0xf8c08020 0xf8c09024 +INFO: BL2: SCP_BL2 0xf8c0a028 0xf3efb02c 0xf3ef8208 0x68118309 +INFO: BL2: SCP_BL2 0xf1026401 0xf0110204 0xbf070f04 0x46113220 +INFO: BL2: SCP_BL2 TAIL: +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x19cad151 0x19b80040 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 +INFO: BL2: SCP_BL2 transferred to SCP +INFO: start fw loading +INFO: fw load success +WARNING: BL2: Platform setup already done!! +INFO: BL2: Loading image id 3 +INFO: Loading image id=3 at address 0x1ac58000 +INFO: Image id=3 loaded: 0x1ac58000 - 0x1ac63024 +INFO: BL2: Loading image id 5 +INFO: Loading image id=5 at address 0x1ac98000 +INFO: Image id=5 loaded: 0x1ac98000 - 0x1ad0819c +NOTICE: BL2: Booting BL31 +INFO: Entry point address = 0x1ac58000 +INFO: SPSR = 0x3cd +NOTICE: BL31: v2.1(debug):v2.1-531-g3ee48f40 +NOTICE: BL31: Built : 18:16:01, Aug 2 2019 +INFO: ARM GICv2 driver initialized +INFO: BL31: Initializing runtime services +INFO: BL31: cortex_a53: CPU workaround for 855873 was applied +INFO: plat_setup_psci_ops: sec_entrypoint=0x1ac580fc +INFO: BL31: Preparing for EL3 exit to normal world +INFO: Entry point address = 0x1ac98000 +INFO: SPSR = 0x3c9 + + +U-Boot 2019.07-00628-g286f05a6fc-dirty (Aug 02 2019 - 17:14:05 +0530) +Hikey960 + +DRAM: 3 GiB +PSCI: v1.1 +MMC: dwmmc1@ff37f000: 0 +Loading Environment from EXT4... ** File not found /uboot.env ** + +** Unable to read "/uboot.env" from mmc0:2 ** +In: serial@fff32000 +Out: serial@fff32000 +Err: serial@fff32000 +Net: Net Initialization Skipped +No ethernet found. +Hit any key to stop autoboot: 0 +switch to partitions #0, OK +mmc0 is current device +Scanning mmc 0:1... +Found /extlinux/extlinux.conf +Retrieving file: /extlinux/extlinux.conf +201 bytes read in 12 ms (15.6 KiB/s) +1: hikey960-kernel +Retrieving file: /Image +24689152 bytes read in 4377 ms (5.4 MiB/s) +append: earlycon=pl011,mmio32,0xfff32000 console=ttyAMA6,115200 rw root=/dev/mmcblk0p2 rot +Retrieving file: /hi3660-hikey960.dtb +35047 bytes read in 14 ms (2.4 MiB/s) +## Flattened Device Tree blob at 10000000 + Booting using the fdt blob at 0x10000000 + Using Device Tree in place at 0000000010000000, end 000000001000b8e6 + +Starting kernel ... + +[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] +[ 0.000000] Linux version 5.2.0-03138-gd75da80dce39 (mani@Mani-XPS-13-9360) (gcc versi9 +[ 0.000000] Machine model: HiKey960 +[ 0.000000] earlycon: pl11 at MMIO32 0x00000000fff32000 (options '') +[ 0.000000] printk: bootconsole [pl11] enabled +[ 0.000000] efi: Getting EFI parameters from FDT: |