diff options
Diffstat (limited to 'board/tqc/tqm8xx/tqm8xx.c')
| -rw-r--r-- | board/tqc/tqm8xx/tqm8xx.c | 82 |
1 files changed, 41 insertions, 41 deletions
diff --git a/board/tqc/tqm8xx/tqm8xx.c b/board/tqc/tqm8xx/tqm8xx.c index 5537d044a5..9a0f3a0ff2 100644 --- a/board/tqc/tqm8xx/tqm8xx.c +++ b/board/tqc/tqm8xx/tqm8xx.c @@ -139,7 +139,7 @@ int checkboard (void) phys_size_t initdram (int board_type) { - volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; volatile memctl8xx_t *memctl = &immap->im_memctl; long int size8, size9, size10; long int size_b0 = 0; @@ -154,7 +154,7 @@ phys_size_t initdram (int board_type) * with two SDRAM banks or four cycles every 31.2 us with one * bank. It will be adjusted after memory sizing. */ - memctl->memc_mptpr = CFG_MPTPR_2BK_8K; + memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K; /* * The following value is used as an address (i.e. opcode) for @@ -176,19 +176,19 @@ phys_size_t initdram (int board_type) * preliminary addresses - these have to be modified after the * SDRAM size has been determined. */ - memctl->memc_or2 = CFG_OR2_PRELIM; - memctl->memc_br2 = CFG_BR2_PRELIM; + memctl->memc_or2 = CONFIG_SYS_OR2_PRELIM; + memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM; #ifndef CONFIG_CAN_DRIVER if ((board_type != 'L') && (board_type != 'M') && (board_type != 'D') ) { /* only one SDRAM bank on L, M and D modules */ - memctl->memc_or3 = CFG_OR3_PRELIM; - memctl->memc_br3 = CFG_BR3_PRELIM; + memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM; + memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM; } #endif /* CONFIG_CAN_DRIVER */ - memctl->memc_mamr = CFG_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */ + memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */ udelay (200); @@ -219,7 +219,7 @@ phys_size_t initdram (int board_type) * * try 8 column mode */ - size8 = dram_size (CFG_MAMR_8COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE); + size8 = dram_size (CONFIG_SYS_MAMR_8COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE); debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size8 >> 20); udelay (1000); @@ -227,30 +227,30 @@ phys_size_t initdram (int board_type) /* * try 9 column mode */ - size9 = dram_size (CFG_MAMR_9COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE); + size9 = dram_size (CONFIG_SYS_MAMR_9COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE); debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size9 >> 20); udelay(1000); -#if defined(CFG_MAMR_10COL) +#if defined(CONFIG_SYS_MAMR_10COL) /* * try 10 column mode */ - size10 = dram_size (CFG_MAMR_10COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE); + size10 = dram_size (CONFIG_SYS_MAMR_10COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE); debug ("SDRAM Bank 0 in 10 column mode: %ld MB\n", size10 >> 20); #else size10 = 0; -#endif /* CFG_MAMR_10COL */ +#endif /* CONFIG_SYS_MAMR_10COL */ if ((size8 < size10) && (size9 < size10)) { size_b0 = size10; } else if ((size8 < size9) && (size10 < size9)) { size_b0 = size9; - memctl->memc_mamr = CFG_MAMR_9COL; + memctl->memc_mamr = CONFIG_SYS_MAMR_9COL; udelay (500); } else { size_b0 = size8; - memctl->memc_mamr = CFG_MAMR_8COL; + memctl->memc_mamr = CONFIG_SYS_MAMR_8COL; udelay (500); } debug ("SDRAM Bank 0: %ld MB\n", size_b0 >> 20); @@ -281,7 +281,7 @@ phys_size_t initdram (int board_type) */ if ((size_b0 < 0x02000000) && (size_b1 < 0x02000000)) { /* reduce to 15.6 us (62.4 us / quad) */ - memctl->memc_mptpr = CFG_MPTPR_2BK_4K; + memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K; udelay (1000); } @@ -290,15 +290,15 @@ phys_size_t initdram (int board_type) */ if (size_b1 > size_b0) { /* SDRAM Bank 1 is bigger - map first */ - memctl->memc_or3 = ((-size_b1) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM; - memctl->memc_br3 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V; + memctl->memc_or3 = ((-size_b1) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM; + memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V; if (size_b0 > 0) { /* * Position Bank 0 immediately above Bank 1 */ - memctl->memc_or2 = ((-size_b0) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM; - memctl->memc_br2 = ((CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V) + memctl->memc_or2 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM; + memctl->memc_br2 = ((CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V) + size_b1; } else { unsigned long reg; @@ -312,24 +312,24 @@ phys_size_t initdram (int board_type) /* adjust refresh rate depending on SDRAM type, one bank */ reg = memctl->memc_mptpr; - reg >>= 1; /* reduce to CFG_MPTPR_1BK_8K / _4K */ + reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */ memctl->memc_mptpr = reg; } } else { /* SDRAM Bank 0 is bigger - map first */ - memctl->memc_or2 = ((-size_b0) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM; + memctl->memc_or2 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM; memctl->memc_br2 = - (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V; + (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V; if (size_b1 > 0) { /* * Position Bank 1 immediately above Bank 0 */ memctl->memc_or3 = - ((-size_b1) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM; + ((-size_b1) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM; memctl->memc_br3 = - ((CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V) + ((CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V) + size_b0; } else { unsigned long reg; @@ -345,7 +345,7 @@ phys_size_t initdram (int board_type) /* adjust refresh rate depending on SDRAM type, one bank */ reg = memctl->memc_mptpr; - reg >>= 1; /* reduce to CFG_MPTPR_1BK_8K / _4K */ + reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */ memctl->memc_mptpr = reg; } } @@ -356,8 +356,8 @@ phys_size_t initdram (int board_type) /* UPM initialization for CAN @ CLKOUT <= 66 MHz */ /* Initialize OR3 / BR3 */ - memctl->memc_or3 = CFG_OR3_CAN; - memctl->memc_br3 = CFG_BR3_CAN; + memctl->memc_or3 = CONFIG_SYS_OR3_CAN; + memctl->memc_br3 = CONFIG_SYS_BR3_CAN; /* Initialize MBMR */ memctl->memc_mbmr = MBMR_GPL_B4DIS; /* GPL_B4 ouput line Disable */ @@ -397,8 +397,8 @@ phys_size_t initdram (int board_type) #ifdef CONFIG_ISP1362_USB /* Initialize OR5 / BR5 */ - memctl->memc_or5 = CFG_OR5_ISP1362; - memctl->memc_br5 = CFG_BR5_ISP1362; + memctl->memc_or5 = CONFIG_SYS_OR5_ISP1362; + memctl->memc_br5 = CONFIG_SYS_BR5_ISP1362; #endif /* CONFIG_ISP1362_USB */ return (size_b0 + size_b1); } @@ -415,7 +415,7 @@ phys_size_t initdram (int board_type) static long int dram_size (long int mamr_value, long int *base, long int maxsize) { - volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; volatile memctl8xx_t *memctl = &immap->im_memctl; memctl->memc_mamr = mamr_value; @@ -451,14 +451,14 @@ int board_early_init_r (void) #ifdef CONFIG_MISC_INIT_R int misc_init_r (void) { - volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; volatile memctl8xx_t *memctl = &immap->im_memctl; -#ifdef CFG_OR_TIMING_FLASH_AT_50MHZ +#ifdef CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ int scy, trlx, flash_or_timing, clk_diff; - scy = (CFG_OR_TIMING_FLASH_AT_50MHZ & OR_SCY_MSK) >> 4; - if (CFG_OR_TIMING_FLASH_AT_50MHZ & OR_TRLX) { + scy = (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & OR_SCY_MSK) >> 4; + if (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & OR_TRLX) { trlx = OR_TRLX; scy *= 2; } else { @@ -498,29 +498,29 @@ int misc_init_r (void) scy = 1; flash_or_timing = (scy << 4) | trlx | - (CFG_OR_TIMING_FLASH_AT_50MHZ & ~(OR_TRLX | OR_SCY_MSK)); + (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & ~(OR_TRLX | OR_SCY_MSK)); memctl->memc_or0 = flash_or_timing | (-flash_info[0].size & OR_AM_MSK); #else memctl->memc_or0 = - CFG_OR_TIMING_FLASH | (-flash_info[0].size & OR_AM_MSK); + CONFIG_SYS_OR_TIMING_FLASH | (-flash_info[0].size & OR_AM_MSK); #endif - memctl->memc_br0 = (CFG_FLASH_BASE & BR_BA_MSK) | BR_MS_GPCM | BR_V; + memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_MS_GPCM | BR_V; debug ("## BR0: 0x%08x OR0: 0x%08x\n", memctl->memc_br0, memctl->memc_or0); if (flash_info[1].size) { -#ifdef CFG_OR_TIMING_FLASH_AT_50MHZ +#ifdef CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ memctl->memc_or1 = flash_or_timing | (-flash_info[1].size & 0xFFFF8000); #else - memctl->memc_or1 = CFG_OR_TIMING_FLASH | + memctl->memc_or1 = CONFIG_SYS_OR_TIMING_FLASH | (-flash_info[1].size & 0xFFFF8000); #endif memctl->memc_br1 = - ((CFG_FLASH_BASE + + ((CONFIG_SYS_FLASH_BASE + flash_info[0]. size) & BR_BA_MSK) | BR_MS_GPCM | BR_V; @@ -557,7 +557,7 @@ int misc_init_r (void) # ifdef CONFIG_IDE_LED void ide_led (uchar led, uchar status) { - volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; /* We have one led for both pcmcia slots */ if (status) { /* led on */ |