diff options
Diffstat (limited to 'doc/README.m54455evb')
| -rw-r--r-- | doc/README.m54455evb | 82 |
1 files changed, 41 insertions, 41 deletions
diff --git a/doc/README.m54455evb b/doc/README.m54455evb index 5c01f0dff1..f695da5f1c 100644 --- a/doc/README.m54455evb +++ b/doc/README.m54455evb @@ -71,12 +71,12 @@ CONFIG_M54455 -- define for all Freescale MCF54455 CPUs CONFIG_M54455EVB -- define for M54455EVB board CONFIG_MCFUART -- define to use common CF Uart driver -CFG_UART_PORT -- define UART port number, start with 0, 1 and 2 +CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2 CONFIG_BAUDRATE -- define UART baudrate CONFIG_MCFRTC -- define to use common CF RTC driver -CFG_MCFRTC_BASE -- provide base address for RTC in immap.h -CFG_RTC_OSCILLATOR -- define RTC clock frequency +CONFIG_SYS_MCFRTC_BASE -- provide base address for RTC in immap.h +CONFIG_SYS_RTC_OSCILLATOR -- define RTC clock frequency RTC_DEBUG -- define to show RTC debug message CONFIG_CMD_DATE -- enable to use date feature in u-boot @@ -84,13 +84,13 @@ CONFIG_MCFFEC -- define to use common CF FEC driver CONFIG_NET_MULTI -- define to use multi FEC in u-boot CONFIG_MII -- enable to use MII driver CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c -CFG_DISCOVER_PHY -- enable PHY discovery -CFG_RX_ETH_BUFFER -- Set FEC Receive buffer -CFG_FAULT_ECHO_LINK_DOWN-- -CFG_FEC0_PINMUX -- Set FEC0 Pin configuration -CFG_FEC1_PINMUX -- Set FEC1 Pin configuration -CFG_FEC0_MIIBASE -- Set FEC0 MII base register -CFG_FEC1_MIIBASE -- Set FEC0 MII base register +CONFIG_SYS_DISCOVER_PHY -- enable PHY discovery +CONFIG_SYS_RX_ETH_BUFFER -- Set FEC Receive buffer +CONFIG_SYS_FAULT_ECHO_LINK_DOWN-- +CONFIG_SYS_FEC0_PINMUX -- Set FEC0 Pin configuration +CONFIG_SYS_FEC1_PINMUX -- Set FEC1 Pin configuration +CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register +CONFIG_SYS_FEC1_MIIBASE -- Set FEC0 MII base register MCFFEC_TOUT_LOOP -- set FEC timeout loop CONFIG_HAS_ETH1 -- define to enable second FEC in u-boot @@ -100,14 +100,14 @@ CONFIG_IDE_RESET -- define ide_reset() CONFIG_IDE_PREINIT -- define ide_preinit() CONFIG_ATAPI -- define ATAPI support CONFIG_LBA48 -- define LBA48 (larger than 120GB) support -CFG_IDE_MAXBUS -- define max channel -CFG_IDE_MAXDEVICE -- define max devices per channel -CFG_ATA_BASE_ADDR -- define ATA base address -CFG_ATA_IDE0_OFFSET -- define ATA IDE0 offset -CFG_ATA_DATA_OFFSET -- define ATA data IO -CFG_ATA_REG_OFFSET -- define for normal register accesses -CFG_ATA_ALT_OFFSET -- define for alternate registers -CFG_ATA_STRIDE -- define for Interval between registers +CONFIG_SYS_IDE_MAXBUS -- define max channel +CONFIG_SYS_IDE_MAXDEVICE -- define max devices per channel +CONFIG_SYS_ATA_BASE_ADDR -- define ATA base address +CONFIG_SYS_ATA_IDE0_OFFSET -- define ATA IDE0 offset +CONFIG_SYS_ATA_DATA_OFFSET -- define ATA data IO +CONFIG_SYS_ATA_REG_OFFSET -- define for normal register accesses +CONFIG_SYS_ATA_ALT_OFFSET -- define for alternate registers +CONFIG_SYS_ATA_STRIDE -- define for Interval between registers _IO_BASE -- define for IO base address CONFIG_MCFTMR -- define to use DMA timer @@ -116,42 +116,42 @@ CONFIG_MCFPIT -- define to use PIT timer CONFIG_FSL_I2C -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SOFT_I2C -- define for I2C bit-banged -CFG_I2C_SPEED -- define for I2C speed -CFG_I2C_SLAVE -- define for I2C slave address -CFG_I2C_OFFSET -- define for I2C base address offset -CFG_IMMR -- define for MBAR offset +CONFIG_SYS_I2C_SPEED -- define for I2C speed +CONFIG_SYS_I2C_SLAVE -- define for I2C slave address +CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset +CONFIG_SYS_IMMR -- define for MBAR offset CONFIG_PCI -- define for PCI support CONFIG_PCI_PNP -- define for Plug n play support -CFG_PCI_MEM_BUS -- PCI memory logical offset -CFG_PCI_MEM_PHYS -- PCI memory physical offset -CFG_PCI_MEM_SIZE -- PCI memory size -CFG_PCI_IO_BUS -- PCI IO logical offset -CFG_PCI_IO_PHYS -- PCI IO physical offset -CFG_PCI_IO_SIZE -- PCI IO size -CFG_PCI_CFG_BUS -- PCI Configuration logical offset -CFG_PCI_CFG_PHYS -- PCI Configuration physical offset -CFG_PCI_CFG_SIZE -- PCI Configuration size +CONFIG_SYS_PCI_MEM_BUS -- PCI memory logical offset +CONFIG_SYS_PCI_MEM_PHYS -- PCI memory physical offset +CONFIG_SYS_PCI_MEM_SIZE -- PCI memory size +CONFIG_SYS_PCI_IO_BUS -- PCI IO logical offset +CONFIG_SYS_PCI_IO_PHYS -- PCI IO physical offset +CONFIG_SYS_PCI_IO_SIZE -- PCI IO size +CONFIG_SYS_PCI_CFG_BUS -- PCI Configuration logical offset +CONFIG_SYS_PCI_CFG_PHYS -- PCI Configuration physical offset +CONFIG_SYS_PCI_CFG_SIZE -- PCI Configuration size CONFIG_EXTRA_CLOCK -- Enable extra clock such as vco, flexbus, pci, etc -CFG_MBAR -- define MBAR offset +CONFIG_SYS_MBAR -- define MBAR offset -CFG_ATMEL_BOOT -- To determine the u-boot is booted from Atmel or Intel +CONFIG_SYS_ATMEL_BOOT -- To determine the u-boot is booted from Atmel or Intel CONFIG_MONITOR_IS_IN_RAM -- Not support -CFG_INIT_RAM_ADDR -- defines the base address of the MCF54455 internal SRAM +CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF54455 internal SRAM -CFG_CSn_BASE -- defines the Chip Select Base register -CFG_CSn_MASK -- defines the Chip Select Mask register -CFG_CSn_CTRL -- defines the Chip Select Control register +CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register +CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register +CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register -CFG_ATMEL_BASE -- defines the Atmel Flash base -CFG_INTEL_BASE -- defines the Intel Flash base +CONFIG_SYS_ATMEL_BASE -- defines the Atmel Flash base +CONFIG_SYS_INTEL_BASE -- defines the Intel Flash base -CFG_SDRAM_BASE -- defines the DRAM Base -CFG_SDRAM_BASE1 -- defines the DRAM Base 1 +CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base +CONFIG_SYS_SDRAM_BASE1 -- defines the DRAM Base 1 2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL =========================================== |