diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/README.uniphier | 58 |
1 files changed, 27 insertions, 31 deletions
diff --git a/doc/README.uniphier b/doc/README.uniphier index 598ff28ccd..a42eaa9761 100644 --- a/doc/README.uniphier +++ b/doc/README.uniphier @@ -2,74 +2,67 @@ U-Boot for UniPhier SoC family ============================== -Tested toolchains ------------------ - - (a) Ubuntu packages (CROSS_COMPILE=arm-linux-gnueabi-) - - If you are building U-Boot on Ubuntu, its standard package is recommended. - You can install it as follows: +Recommended toolchains +---------------------- - $ sudo apt-get install gcc-arm-linux-gnueabi- - - (b) Linaro compilers (CROSS_COMPILE=arm-linux-gnueabihf-) - - You can download pre-built toolchains from: +The UniPhir platform is well tested with Linaro toolchanis. +You can download pre-built toolchains from: http://www.linaro.org/downloads/ - (c) kernel.org compilers (CROSS_COMPILE=arm-unknown-linux-gnueabi-) - - You can download pre-built toolchains from: - - ftp://www.kernel.org/pub/tools/crosstool/files/bin/ - Compile the source ------------------ sLD3 reference board: $ make uniphier_sld3_defconfig - $ make CROSS_COMPILE=arm-linux-gnueabi- + $ make CROSS_COMPILE=arm-linux-gnueabihf- LD4 reference board: $ make uniphier_ld4_sld8_defconfig - $ make CROSS_COMPILE=arm-linux-gnueabi- + $ make CROSS_COMPILE=arm-linux-gnueabihf- sLD8 reference board: $ make uniphier_ld4_sld8_defconfig - $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-sld8-ref + $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-sld8-ref Pro4 reference board: $ make uniphier_pro4_defconfig - $ make CROSS_COMPILE=arm-linux-gnueabi- + $ make CROSS_COMPILE=arm-linux-gnueabihf- Pro4 Ace board: $ make uniphier_pro4_defconfig - $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-pro4-ace + $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pro4-ace Pro4 Sanji board: $ make uniphier_pro4_defconfig - $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-pro4-sanji + $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pro4-sanji Pro5 4KBOX Board: $ make uniphier_pxs2_ld6b_defconfig - $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-pro5-4kbox + $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pro5-4kbox PXs2 Gentil board: $ make uniphier_pxs2_ld6b_defconfig - $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-pxs2-gentil + $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pxs2-gentil PXs2 Vodka board: $ make uniphier_pxs2_ld6b_defconfig - $ make CROSS_COMPILE=arm-linux-gnueabi- + $ make CROSS_COMPILE=arm-linux-gnueabihf- LD6b reference board: $ make uniphier_pxs2_ld6b_defconfig - $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ld6b-ref + $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-ld6b-ref + +LD11 reference board: + $ make uniphier_ld11_defconfig + $ make CROSS_COMPILE=aarch64-linux-gnu- -You may wish to change the "CROSS_COMPILE=arm-linux-gnueabi-" -to use your favorite compiler. +LD20 reference board: + $ make uniphier_ld20_defconfig + $ make CROSS_COMPILE=aarch64-linux-gnu- + +You may wish to change the "CROSS_COMPILE=..." to use your favorite compiler. Burn U-Boot images to NAND @@ -119,6 +112,9 @@ UniPhier specific commands - ddrphy (enabled by CONFIG_CMD_DDRPHY_DUMP) shows the DDR PHY parameters set by the PHY training + - ddrmphy (enabled by CONFIG_CMD_DDRMPHY_DUMP) + shows the DDR Multi PHY parameters set by the PHY training + Supported devices ----------------- @@ -179,4 +175,4 @@ newer SoCs. Even if it is, EA[25] is not connected on most of the boards. -- Masahiro Yamada <yamada.masahiro@socionext.com> -Feb. 2016 +Oct. 2016 |