diff options
Diffstat (limited to 'include/configs/MPC8641HPCN.h')
| -rw-r--r-- | include/configs/MPC8641HPCN.h | 289 |
1 files changed, 206 insertions, 83 deletions
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 542877bca5..69b4c4410d 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -38,18 +38,32 @@ #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ #define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ +/*#define CONFIG_PHYS_64BIT 1*/ /* Place devices in 36-bit space */ #ifdef RUN_DIAG -#define CONFIG_SYS_DIAG_ADDR 0xff800000 +#define CONFIG_SYS_DIAG_ADDR CONFIG_SYS_FLASH_BASE #endif #define CONFIG_SYS_RESET_ADDRESS 0xfff00100 +/* + * virtual address to be used for temporary mappings. There + * should be 128k free at this VA. + */ +#define CONFIG_SYS_SCRATCH_VA 0xe0000000 + +/* + * set this to enable Rapid IO. PCI and RIO are mutually exclusive + */ +/*#define CONFIG_RIO 1*/ + +#ifndef CONFIG_RIO /* RIO/PCI are mutually exclusive */ #define CONFIG_PCI 1 /* Enable PCI/PCIE */ #define CONFIG_PCI1 1 /* PCIE controler 1 (ULI bridge) */ #define CONFIG_PCI2 1 /* PCIE controler 2 (slot) */ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ +#endif #define CONFIG_FSL_LAW 1 /* Use common FSL law init code */ #define CONFIG_TSEC_ENET /* tsec ethernet support */ @@ -79,13 +93,35 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_MEMTEST_END 0x00400000 /* + * With the exception of PCI Memory and Rapid IO, most devices will simply + * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA + * when 36-bit is enabled. When 36-bit is not enabled, these bits are 0. + */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f00000000ULL +#else +#define CONFIG_SYS_PHYS_ADDR_HIGH 0x0 +#endif + +/* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xf8000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +/* Physical addresses */ +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0xf +#define CONFIG_SYS_CCSRBAR_PHYS (CONFIG_SYS_CCSRBAR_PHYS_LOW \ + | ((u64)CONFIG_SYS_CCSRBAR_PHYS_HIGH << 32)) +#else +#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW +#endif + #define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) #define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) @@ -102,6 +138,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ #define CONFIG_VERY_BIG_RAM #define MPC86xx_DDR_SDRAM_CLK_CNTL @@ -145,38 +182,46 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -/* - * In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000. - * There is an 8MB flash. In effect, the addresses from fe000000 to fe7fffff - * map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff. - * However, when u-boot comes up, the flash_init needs hard start addresses - * to build its info table. For user convenience, the flash addresses is - * fe800000 and ff800000. That way, u-boot knows where the flash is - * and the user can download u-boot code from promjet to fef00000, a - * more intuitive location than fe700000. - * - * Note that, on switching the boot location, fef00000 becomes fff00000. - */ -#define CONFIG_SYS_FLASH_BASE 0xfe800000 /* start of FLASH 32M */ -#define CONFIG_SYS_FLASH_BASE2 0xff800000 +#define CONFIG_SYS_FLASH_BASE 0xef800000 /* start of FLASH 8M */ +#define CONFIG_SYS_FLASH_BASE_PHYS (CONFIG_SYS_FLASH_BASE \ + | CONFIG_SYS_PHYS_ADDR_HIGH) -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} -#define CONFIG_SYS_BR0_PRELIM 0xff001001 /* port size 16bit */ -#define CONFIG_SYS_OR0_PRELIM 0xff006ff7 /* 16MB Boot Flash area*/ +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} -#define CONFIG_SYS_BR1_PRELIM 0xfe001001 /* port size 16bit */ -#define CONFIG_SYS_OR1_PRELIM 0xff006ff7 /* 16MB Alternate Boot Flash area*/ +/* Convert an address into the right format for the BR registers */ +#ifdef CONFIG_PHYS_64BIT +#define BR_PHYS_ADDR(x) ((unsigned long)((x & 0x0ffff8000ULL) | \ + ((x & 0x300000000ULL) >> 19))) +#else +#define BR_PHYS_ADDR(x) (x & 0xffff8000) +#endif + +#define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ + | 0x00001001) /* port size 16bit */ +#define CONFIG_SYS_OR0_PRELIM 0xff806ff7 /* 8MB Boot Flash area*/ -#define CONFIG_SYS_BR2_PRELIM 0xf8201001 /* port size 16bit */ -#define CONFIG_SYS_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/ +#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CF_BASE_PHYS) \ + | 0x00001001) /* port size 16bit */ +#define CONFIG_SYS_OR2_PRELIM 0xffffeff7 /* 32k Compact Flash */ -#define CONFIG_SYS_BR3_PRELIM 0xf8100801 /* port size 8bit */ -#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ +#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) \ + | 0x00000801) /* port size 8bit */ +#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32k PIXIS area*/ +/* + * The LBC_BASE is the base of the region that contains the PIXIS and the CF. + * The PIXIS and CF by themselves aren't large enough to take up the 128k + * required for the smallest BAT mapping, so there's a 64k hole. + */ +#define CONFIG_SYS_LBC_BASE 0xffde0000 +#define CONFIG_SYS_LBC_BASE_PHYS (CONFIG_SYS_LBC_BASE \ + | CONFIG_SYS_PHYS_ADDR_HIGH) #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ -#define PIXIS_BASE 0xf8100000 /* PIXIS registers */ +#define PIXIS_BASE (CONFIG_SYS_LBC_BASE + 0x00010000) +#define PIXIS_BASE_PHYS (CONFIG_SYS_LBC_BASE_PHYS + 0x00010000) +#define PIXIS_SIZE 0x00008000 /* 32k */ #define PIXIS_ID 0x0 /* Board ID at offset 0 */ #define PIXIS_VER 0x1 /* Board version at offset 1 */ #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ @@ -193,13 +238,18 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ #define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +/* Compact flash shares a BAT with PIXIS; make sure they're contiguous */ +#define CF_BASE (PIXIS_BASE + PIXIS_SIZE) +#define CF_BASE_PHYS (PIXIS_BASE_PHYS + PIXIS_SIZE) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ #undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI @@ -279,8 +329,12 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * RapidIO MMU */ -#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */ +#define CONFIG_SYS_RIO_MEM_BASE 0x80000000 /* base address */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_RIO_MEM_PHYS 0x0000000c00000000ULL +#else #define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE +#endif #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ /* @@ -288,22 +342,33 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * Addresses are mapped 1-1. */ #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCI1_MEM_PHYS 0x0000000c00000000ULL +#else #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#endif #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCI1_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCI1_IO_PHYS (CONFIG_SYS_PCI1_IO_VIRT \ + | CONFIG_SYS_PHYS_ADDR_HIGH) +#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64K */ /* For RTL8139 */ #define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);}) #define _IO_BASE 0x00000000 -#define CONFIG_SYS_PCI2_MEM_BASE 0xa0000000 -#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE +#define CONFIG_SYS_PCI2_MEM_BASE (CONFIG_SYS_PCI1_MEM_BASE \ + + CONFIG_SYS_PCI1_MEM_SIZE) +#define CONFIG_SYS_PCI2_MEM_PHYS (CONFIG_SYS_PCI1_MEM_PHYS \ + + CONFIG_SYS_PCI1_MEM_SIZE) #define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCI2_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI2_IO_PHYS 0xe3000000 -#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCI2_IO_VIRT (CONFIG_SYS_PCI1_IO_VIRT \ + + CONFIG_SYS_PCI1_IO_SIZE) +#define CONFIG_SYS_PCI2_IO_PHYS (CONFIG_SYS_PCI1_IO_PHYS \ + + CONFIG_SYS_PCI1_IO_SIZE) +#define CONFIG_SYS_PCI2_IO_SIZE CONFIG_SYS_PCI1_IO_SIZE #if defined(CONFIG_PCI) @@ -331,17 +396,11 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 -#if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xe0000000 - #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ -#endif - /*PCIE video card used*/ -#define VIDEO_IO_OFFSET CONFIG_SYS_PCI2_IO_PHYS +#define VIDEO_IO_OFFSET CONFIG_SYS_PCI2_IO_VIRT /*PCI video card used*/ -/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_PHYS*/ +/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/ /* video */ #define CONFIG_VIDEO @@ -354,7 +413,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_ATI_RADEON_FB #define CONFIG_VIDEO_LOGO /*#define CONFIG_CONSOLE_CURSOR*/ -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCI2_IO_PHYS +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCI2_IO_VIRT #endif #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ @@ -408,9 +467,23 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #endif /* CONFIG_TSEC_ENET */ +/* Contort an addr into the format needed for BATs */ +#ifdef CONFIG_PHYS_64BIT +#define BAT_PHYS_ADDR(x) ((unsigned long) \ + ((x & 0x00000000ffffffffULL) | \ + ((x & 0x0000000e00000000ULL) >> 24) | \ + ((x & 0x0000000100000000ULL) >> 30))) +#else +#define BAT_PHYS_ADDR(x) (x) +#endif + + +/* Put high physical address bits into the BAT format */ +#define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8) +#define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2) + /* - * BAT0 2G Cacheable, non-guarded - * 0x0000_0000 2G DDR + * BAT0 DDR */ #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) #define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) @@ -418,52 +491,90 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U /* - * BAT1 1G Cache-inhibited, guarded - * 0x8000_0000 512M PCI-Express 1 Memory - * 0xa000_0000 512M PCI-Express 2 Memory - * Changed it for operating from 0xd0000000 + * BAT1 LBC (PIXIS/CF) */ -#define CONFIG_SYS_DBAT1L ( CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW \ - | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_DBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS) \ + | BATL_PP_RW | BATL_CACHEINHIBIT | \ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT1U (CONFIG_SYS_LBC_BASE | BATU_BL_128K \ + | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS) \ + | BATL_PP_RW | BATL_MEMCOHERENCE) #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U -/* - * BAT2 512M Cache-inhibited, guarded - * 0xc000_0000 512M RapidIO Memory +/* if CONFIG_PCI: + * BAT2 PCI1 and PCI1 MEM + * if CONFIG_RIO + * BAT2 Rapidio Memory */ +#ifdef CONFIG_PCI +#define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_MEM_PHYS) \ + | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_1G \ + | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_MEM_PHYS) \ + | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U +#else /* CONFIG_RIO */ +#define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_RIO_MEM_PHYS) \ + | BATL_PP_RW | BATL_CACHEINHIBIT | \ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT2U (CONFIG_SYS_RIO_MEM_BASE | BATU_BL_512M \ + | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_RIO_MEM_PHYS) \ + | BATL_PP_RW | BATL_CACHEINHIBIT) + #define CONFIG_SYS_DBAT2L (CONFIG_SYS_RIO_MEM_PHYS | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT2U (CONFIG_SYS_RIO_MEM_PHYS | BATU_BL_512M | BATU_VS | BATU_VP) #define CONFIG_SYS_IBAT2L (CONFIG_SYS_RIO_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U +#endif /* - * BAT3 4M Cache-inhibited, guarded - * 0xf800_0000 4M CCSR + * BAT3 CCSR Space + * This BAT is used early; don't use any macros with ULL - use HIGH/LOW pairs + * instead. The assembler chokes on ULL. */ -#define CONFIG_SYS_DBAT3L ( CONFIG_SYS_CCSRBAR | BATL_PP_RW \ - | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR_PHYS_LOW \ + | PHYS_HIGH_TO_BXPN(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ + | PHYS_HIGH_TO_BX(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ + | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR_PHYS_LOW \ + | PHYS_HIGH_TO_BXPN(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ + | PHYS_HIGH_TO_BX(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ + | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U +#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) +#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ + | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ + | BATU_BL_1M | BATU_VS | BATU_VP) +#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ + | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU +#endif + /* - * BAT4 32M Cache-inhibited, guarded - * 0xe200_0000 16M PCI-Express 1 I/O - * 0xe300_0000 16M PCI-Express 2 I/0 - * Note that this is at 0xe0000000 + * BAT4 PCI1_IO and PCI2_IO */ -#define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW \ - | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_IO_PHYS) \ + | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_128K \ + | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_IO_PHYS) \ + | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U /* - * BAT5 128K Cacheable, non-guarded - * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory) + * BAT5 Init RAM for stack in the CPU DCache (no backing memory) */ #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) @@ -471,15 +582,28 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U /* - * BAT6 32M Cache-inhibited, guarded - * 0xfe00_0000 32M FLASH + * BAT6 FLASH */ -#define CONFIG_SYS_DBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW \ - | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT6U ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE) +#define CONFIG_SYS_DBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ + | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_IBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ + | BATL_PP_RW | BATL_MEMCOHERENCE) #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U +/* Map the last 1M of flash where we're running from reset */ +#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ + | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT6U_EARLY (TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY + +/* + * BAT7 FREE - used later for tmp mappings + */ #define CONFIG_SYS_DBAT7L 0x00000000 #define CONFIG_SYS_DBAT7U 0x00000000 #define CONFIG_SYS_IBAT7L 0x00000000 @@ -492,12 +616,11 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x60000) #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ - #define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 #endif +#define CONFIG_ENV_SIZE 0x2000 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ @@ -624,8 +747,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); "ramdiskfile=your.ramdisk.u-boot\0" \ "fdtaddr=c00000\0" \ "fdtfile=mpc8641_hpcn.dtb\0" \ - "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ - "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ + "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0" \ + "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \ "maxcpus=2" |