diff options
Diffstat (limited to 'include/configs/strider.h')
| -rw-r--r-- | include/configs/strider.h | 175 |
1 files changed, 1 insertions, 174 deletions
diff --git a/include/configs/strider.h b/include/configs/strider.h index 972543d6bd..8b942e3446 100644 --- a/include/configs/strider.h +++ b/include/configs/strider.h @@ -12,100 +12,19 @@ * High Level Configuration Options */ #define CONFIG_E300 1 /* E300 family */ -#define CONFIG_MPC83xx 1 /* MPC83xx family */ -#define CONFIG_MPC830x 1 /* MPC830x family */ -#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ -#define CONFIG_STRIDER 1 /* STRIDER board specific */ #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR /* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 33333333 /* in Hz */ -#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN - -/* - * Hardware Reset Configuration Word - * if CLKIN is 66.66MHz, then - * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz - * We choose the A type silicon as default, so the core is 400Mhz. - */ -#define CONFIG_SYS_HRCW_LOW (\ - HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ - HRCWL_DDR_TO_SCB_CLK_2X1 |\ - HRCWL_SVCOD_DIV_2 |\ - HRCWL_CSB_TO_CLKIN_4X1 |\ - HRCWL_CORE_TO_CSB_3X1) -/* - * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits - * in 8308's HRCWH according to the manual, but original Freescale's - * code has them and I've expirienced some problems using the board - * with BDI3000 attached when I've tried to set these bits to zero - * (UART doesn't work after the 'reset run' command). - */ -#define CONFIG_SYS_HRCW_HIGH (\ - HRCWH_PCI_HOST |\ - HRCWH_PCI1_ARBITER_ENABLE |\ - HRCWH_CORE_ENABLE |\ - HRCWH_FROM_0XFFF00100 |\ - HRCWH_BOOTSEQ_DISABLE |\ - HRCWH_SW_WATCHDOG_DISABLE |\ - HRCWH_ROM_LOC_LOCAL_16BIT |\ - HRCWH_RL_EXT_LEGACY |\ - HRCWH_TSEC1M_IN_MII |\ - HRCWH_TSEC2M_IN_RGMII |\ - HRCWH_BIG_ENDIAN) - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRH (\ - SICRH_ESDHC_A_SD |\ - SICRH_ESDHC_B_SD |\ - SICRH_ESDHC_C_SD |\ - SICRH_GPIO_A_GPIO |\ - SICRH_GPIO_B_GPIO |\ - SICRH_IEEE1588_A_GPIO |\ - SICRH_USB |\ - SICRH_GTM_GPIO |\ - SICRH_IEEE1588_B_GPIO |\ - SICRH_ETSEC2_GPIO |\ - SICRH_GPIOSEL_1 |\ - SICRH_TMROBI_V3P3 |\ - SICRH_TSOBI1_V2P5 |\ - SICRH_TSOBI2_V2P5) /* 0x0037f103 */ -#define CONFIG_SYS_SICRL (\ - SICRL_SPI_PF0 |\ - SICRL_UART_PF0 |\ - SICRL_IRQ_PF0 |\ - SICRL_I2C2_PF0 |\ - SICRL_ETSEC1_TX_CLK) /* 0x00000000 */ - -/* - * IMMR new address - */ -#define CONFIG_SYS_IMMR 0xE0000000 - -/* * SERDES */ #define CONFIG_FSL_SERDES #define CONFIG_FSL_SERDES1 0xe3000 /* - * Arbiter Setup - */ -#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ -#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ -#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ - -/* * DDR Setup */ -#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ | DDRCDR_PZ_LOZ \ @@ -192,13 +111,6 @@ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) /* - * Local Bus Configuration & Clock Setup - */ -#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP -#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 -#define CONFIG_SYS_LBC_LBCR 0x00040000 - -/* * FLASH on the Local Bus */ #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT @@ -208,22 +120,6 @@ #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */ -/* Window base at flash base */ -#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ - | BR_PS_16 /* 16 bit port */ \ - | BR_MS_GPCM /* MSEL = GPCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ - | OR_UPM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_ACS_DIV2 \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET) #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 135 @@ -231,29 +127,6 @@ #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -/* - * FPGA - */ -#define CONFIG_SYS_FPGA0_BASE 0xE0600000 -#define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */ - -/* Window base at FPGA base */ -#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE -#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB) - -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \ - | BR_PS_16 /* 16 bit port */ \ - | BR_MS_GPCM /* MSEL = GPCM */ \ - | BR_V) /* valid */ - -#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \ - | OR_UPM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_SCY_5 \ - | OR_GPCM_TRLX_CLEAR \ - | OR_GPCM_EHTR_CLEAR) - -#define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE #define CONFIG_SYS_FPGA_DONE(k) 0x0010 #define CONFIG_SYS_FPGA_COUNT 1 @@ -547,52 +420,6 @@ void fpga_control_clear(unsigned int bus, int pin); #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* - * Core HID Setup - */ -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ - HID0_ENABLE_INSTRUCTION_CACHE | \ - HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) -#define CONFIG_SYS_HID2 HID2_HBE - -/* - * MMU Setup - */ - -/* DDR: cache cacheable */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ - BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ - BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -/* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ - BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ - BATU_VP) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* FLASH: icache cacheable, but dcache-inhibit and guarded */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ - BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ - BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ - BATL_CACHEINHIBIT | \ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -/* Stack in dcache: cacheable, no memory coherence */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ - BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* * Environment Configuration */ |