summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
* spi: xilinx_spi: Use BIT macroJagan Teki2015-10-271-16/+16
* spi: ti_qspi: Use BIT macroJagan Teki2015-10-271-5/+5
* spi: tegra: Use BIT macroJagan Teki2015-10-273-86/+86
* spi: sh_qspi: Use BIT macroJagan Teki2015-10-271-8/+8
* spi: omap3_spi: Use BIT macroJagan Teki2015-10-271-24/+24
* spi: mpc8xxx_spi: Use BIT macroJagan Teki2015-10-271-1/+1
* spi: ich: Use BIT macroJagan Teki2015-10-271-2/+2
* spi: fsl: Use BIT macroJagan Teki2015-10-273-13/+13
* spi: designware_spi: Use BIT macroJagan Teki2015-10-271-7/+7
* spi: cadence_qspi_apb: Use BIT macroJagan Teki2015-10-271-14/+14
* spi: bfin_spi6xx: Use BIT macroJagan Teki2015-10-271-4/+4
* spi: atmel_spi: Use BIT macroJagan Teki2015-10-271-26/+26
* spi: zynq_[q]spi: Use GENMASK macroJagan Teki2015-10-272-7/+7
* spi: zynq_[q]spi: Use BIT macroJagan Teki2015-10-272-18/+18
* spi: zynq_qspi: Minor cleanupsJagan Teki2015-10-251-5/+3
* sf: Add FSR support to spi_flash_cmd_wait_readyJagan Teki2015-10-254-11/+60
* sf: Update status reg check in spi_flash_cmd_wait_readyJagan Teki2015-10-251-58/+13
* sf: Make flash->flags use for generic usageJagan Teki2015-10-253-7/+11
* sf: Optimize BAR write codeJagan Teki2015-10-251-28/+13
* sf: Add spi_flash_read_barJagan Teki2015-10-251-19/+34
* sf: Return bank_sel, if flash->bank_curr == bank_selJagan Teki2015-10-251-1/+1
* spi: zynq_spi: Remove unneeded headersJagan Teki2015-10-251-5/+1
* zynq-common: Add SPL SPI offset, size configsSiva Durga Prasad Paladugu2015-10-251-0/+4
* spi: zynq_qspi: Fix to configure CPOL, CPHA maskJagan Teki2015-10-251-3/+4
* zynq-common: Enable ISSI SPI-NOR flash supportJagan Teki2015-10-251-0/+1
* sf: params: Add IS25LP128 part supportJagan Teki2015-10-251-0/+1
* sf: params: Add IS25LP064 part supportJagan Teki2015-10-251-0/+1
* sf: params: Add IS25LP032 part supportJagan Teki2015-10-251-0/+3
* spi: zynq_spi: Store cs value into private dataJagan Teki2015-10-251-3/+5
* spi: zynq_spi: Rename baudrate divisor mask nameJagan Teki2015-10-251-2/+2
* spi: zynq_spi: Add config reg shift named macrosJagan Teki2015-10-251-3/+7
* spi: Kconfig: Add Zynq QSPI controller entryJagan Teki2015-10-251-0/+9
* configs: zynq: Enable zynq qspi controllerJagan Teki2015-10-256-0/+6
* zynq-common: Enable Bank/Extended address register supportJagan Teki2015-10-251-0/+1
* zynq-common: Enable zynq qspi controller supportJagan Teki2015-10-251-0/+9
* configs: Enable legacy SPI flash interface supportJagan Teki2015-10-255-0/+5
* dts: zed: Enable zynq qspi controller nodeJagan Teki2015-10-251-0/+5
* dts: zc770-xm010: Enable zynq qspi controller nodeJagan Teki2015-10-251-1/+6
* dts: zc706: Enable zynq qspi controller nodeJagan Teki2015-10-251-0/+5
* dts: zc702: Enable zynq qspi controller nodeJagan Teki2015-10-251-0/+5
* dts: microzed: Enable zynq qspi controller nodeJagan Teki2015-10-251-0/+5
* doc: device-tree-bindings: spi: Add zynq qspi infoJagan Teki2015-10-251-0/+26
* dts: zynq: Add zynq qspi controller nodesJagan Teki2015-10-251-0/+12
* spi: Add zynq qspi controller driverJagan Teki2015-10-252-0/+623
* common/board_f.c: modify the macro to use get_clocks() more commonGong Qianyu2015-10-2441-1/+41
* arm, powerpc: select SYS_GENERIC_BOARDMasahiro Yamada2015-10-24236-258/+2
* Revert "ARM: zynq: disable CONFIG_SYS_MALLOC_F to fix MMC boot"Simon Glass2015-10-2410-10/+0
* zynq: Move SPL console init out of board_init_f()Simon Glass2015-10-241-1/+1
* microblaze: Add a TODO to call board_init_f_mem()Simon Glass2015-10-241-0/+2
* arm: Switch 32-bit ARM to using generic global_data setupSimon Glass2015-10-241-24/+4
View Lorry Controller Status