summaryrefslogtreecommitdiff
path: root/configs/mx6dlarm2_defconfig
Commit message (Collapse)AuthorAgeFilesLines
* configs: Resync with savedefconfigWIP/04Dec2019Tom Rini2019-12-041-1/+0
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* env: Finish migration of common ENV optionsTom Rini2019-11-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini2019-11-201-0/+1
| | | | | | | | | | | Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_FSL_USDHC to KconfigAdam Ford2019-08-231-1/+1
| | | | | | | | | This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert to use fsl_esdhc_imx for i.MX platformsYangbo Lu2019-06-231-1/+1
| | | | | | | | | | | Converted to use fsl_esdhc_imx for i.MX platforms. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Martyn Welch <martyn.welch@collabora.com> Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
* configs: Resync with savedefconfigTom Rini2019-04-291-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Kconfig: Migrate BOUNCE_BUFFERPhilipp Tomsich2019-01-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | The bounce buffer is used by a few drivers (most of the MMC drivers) to overcome limitations in their respective DMA implementation. This moves the configuration to Kconfig and makes it user-selectable (even though it will be a required feature to make those drivers work): the expected usage is for drivers depending on this to 'select' it unconditionally from their respective Kconfig (see follow-up patches). This commit includes a full migration using moveconfig.py to ensure that each commit compiles. To ensure bisectability we update dependencies of various drivers to now select BOUNCE_BUFFER when needed. [trini: Squash all patches to ensure bisectability] Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion] Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion] Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
* Convert CONFIG_MII et al to KconfigAdam Ford2018-08-171-0/+1
| | | | | | | | | | This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini2018-08-161-0/+1
| | | | | | | | | | | We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
* treewide: Migrate CONFIG_FSL_ESDHC to KconfigMario Six2018-04-081-0/+1
| | | | | | Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford2018-02-231-0/+1
| | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate CONFIG_SYS_TEXT_BASETom Rini2018-02-111-0/+1
| | | | | | | | | | | On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
* cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen2017-10-101-1/+0
| | | | | | | | | | | | | | Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
* usb: net: migrate USB Ethernet adapters to KconfigChris Packham2017-09-081-0/+1
| | | | | | | | This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig. Update defconfigs. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* usb: net: migrate CONFIG_USB_HOST_ETHER to KconfigChris Packham2017-09-081-0/+1
| | | | | | | | | | CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and LAN78XX options under new menu. Finally update the defconfigs that need CONFIG_USB_HOST_ETHER. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* configs: Resync with savedefconfigTom Rini2017-08-281-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2017-08-141-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass2017-07-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_CMD_BMODE to KconfigSimon Glass2017-04-301-0/+1
| | | | | | | | | This converts the following to Kconfig: CONFIG_CMD_BMODE Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Make this default y and depend on mx5/6/7] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_BOARD_EARLY_INIT_F to KconfigSimon Glass2017-01-251-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: Simon Glass <sjg@chromium.org>
* configs: Migrate CONFIG_USB_STORAGETom Rini2016-09-091-0/+2
| | | | | | | In some cases we were missing CONFIG_USB=y so enable that when needed. Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Re-sync BOOTDELAY changesTom Rini2016-06-171-0/+1
| | | | | | | | With updated moveconfig.py and an better default, re-generate the migration of BOOTDELAY to the defconfig. Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Re-sync with cmd/KconfigTom Rini2016-04-251-0/+9
| | | | | | | Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Re-sync almost all of cmd/KconfigTom Rini2016-04-251-0/+3
| | | | | | | | This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Re-sync HUSH optionsTom Rini2016-04-251-0/+1
| | | | | | | Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default. Signed-off-by: Tom Rini <trini@konsulko.com>
* Move CONFIG_OF_LIBFDT to KconfigSimon Glass2016-03-141-0/+1
| | | | | | Move this option to Kconfig and tidy up existing boards. Signed-off-by: Simon Glass <sjg@chromium.org>
* common: add CMD_GPIO to KconfigThomas Chou2015-11-181-0/+1
| | | | | | | Add CMD_GPIO to Kconfig and run tools/moveconfig.py . Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: Simon Glass <sjg@chromium.org>
* imx: mx6 move TARGET_xx Kconfig option to mx6 specific Kconfig filePeng Fan2015-09-021-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move TARGET_xx Kconfig option based on mx6 to arch/arm/cpu/armv7/mx6/Kconfig. Add enable "CONFIG_ARCH_MX6" for boards based on mx6. Then we can choose target boards using "make ARCH=arm menuconfig" with ARCH_MX6 defined. If using original way, we have no chance to enable ARCH_MX6 when "make menuconfig". Even define CONFIG_ARCH_MX6=y in xx_defconfig, kconfig will complains "arch/../configs/platinum_titanium_defconfig:3: warning: override: TARGET_PLATINUM_TITANIUM changes choice state" Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Eric Bénard <eric@eukrea.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Marek Vasut <marex@denx.de> Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Soeren Moch <smoch@web.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Soeren Moch <smoch@web.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
* Move defaults from config_cmd_default.h to KconfigJoe Hershberger2015-06-251-1/+3
| | | | | | | | | | This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
* net: Move the CMD_NET config to defconfigsJoe Hershberger2015-06-011-0/+1
| | | | | | | | | | | This also selects CONFIG_NET for any CONFIG_CMD_NET board. Remove the imx default for CONFIG_NET. This moves the config that was defined by 60296a8 (commands: add more command entries in Kconfig). Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
* Clean all defconfigs with savedefconfigJoe Hershberger2015-05-121-1/+1
| | | | | | | | | | | | | In order to reduce merge conflicts and to maintain the simplest possible defconfig files, we should be using the savedefconfig feature of Kconfig every time a new feature is added. This keeps the defconfig settings to a minimum (only those things not default) and keeps them in the same order as the Kconfig options. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: Tom Rini <trini@konsulko.com>
* imx: mx6dlarm2: Add support for i.MX6Q/DL arm2 LPDDR2 boardsYe.Li2014-09-301-1/+1
| | | | | | | | Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2 arm2 board. Since the LPDDR2 arm2 board has different DDR size, use CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE. Signed-off-by: Ye.Li <B37916@freescale.com>
* imx: mx6dlarm2: Add support for i.MX6DL arm2 DDR3 boardYe.Li2014-09-301-0/+3
This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2 shared the same board with i.MX6Q ARM2 board since the i.MX6DL is pin-pin compatible with i.MX6Q. The patch also support the DDR 32-BIT mode option. Please define CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT mode.But due to the board design, it's 64bit DDR buswidth physically, so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it. Signed-off-by: Ye.Li <B37916@freescale.com>
View Lorry Controller Status