summaryrefslogtreecommitdiff
path: root/configs/mx6sabresd_defconfig
Commit message (Collapse)AuthorAgeFilesLines
* env: Finish migration of common ENV optionsTom Rini2019-11-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini2019-11-201-0/+1
| | | | | | | | | | | Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2019-11-071-2/+0
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* imx: mx6sabresd: fix usb start when DM enabledPeng Fan2019-10-081-0/+1
| | | | | | Enable CONFIG_DM_REGULATOR_FIXED to let vbus regulator work. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* mx6sabresd: Reduce overall SPL sizeFabio Estevam2019-10-081-3/+0
| | | | | | | | | | | | | | | | | | | Currently the SPL binary is 67 kB, which leaves only 1 kB of free internal RAM space. The following options can be safely removed to save some precious SPL space: - CONFIG_SPL_FS_EXT4: u-boot-dtb.img is stored in raw sector via dd command (at offset 69 kB) - CONFIG_SPL_I2C_SUPPORT: I2C is not used during SPL - CONFIG_SPL_OS_BOOT: no need to make Falcon mode supported by default After this change the SPL binary size gets down to 51 kB. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
* configs: Resync with savedefconfigTom Rini2019-09-231-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* imx: mx6sabresd: fix splash logo drawingAnatolij Gustschin2019-09-211-0/+2
| | | | | | | | | | After mxc_ipuv3 DM_VIDEO conversion showing splash image doesn't work. Fix this. Also enable white on black console configuration as it used to be with cfb_console driver. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reported-by: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Estevam <festevam@gmail.com>
* Convert CONFIG_FSL_USDHC to KconfigAdam Ford2019-08-231-1/+1
| | | | | | | | | This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert to use fsl_esdhc_imx for i.MX platformsYangbo Lu2019-06-231-1/+1
| | | | | | | | | | | Converted to use fsl_esdhc_imx for i.MX platforms. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Martyn Welch <martyn.welch@collabora.com> Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
* configs: Resync with savedefconfigTom Rini2019-06-211-2/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* mx6sabresd: Select pinctrl driverFabio Estevam2019-06-111-0/+2
| | | | | | With the conversion to DM we should select the pinctrl driver. Signed-off-by: Fabio Estevam <festevam@gmail.com>
* mx6sabresd: Remove CONFIG_SPL_DM to decrease the SPL sizeFabio Estevam2019-06-111-1/+0
| | | | | | | | | | | | | | | | | | | Currently the mx6qsabresd board does not boot: U-Boot SPL 2019.07-rc2 (May 16 2019 - 14:28:55 -0300) Trying to boot from MMC1 spl: could not find mmc device 0. error: -19 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### The reason for the boot failure is that that the SPL size got greater than the 68KB limit (4KB header + 64KB max size) as explained in include/configs/imx6_spl.h. Remove the CONFIG_SPL_DM option, so that the SPL binary could fit into the allowed size and the board can boot again. Signed-off-by: Fabio Estevam <festevam@gmail.com>
* imx: mx6sabresd: fix boot hang with videoPeng Fan2019-05-201-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Meet the following boot hang. " U-Boot SPL 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800) Trying to boot from MMC1 U-Boot 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800) CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C)Reset cause: POR Model: Freescale i.MX6 Quad SABRE Smart Device Board Board: MX6-SabreSD I2C: ready DRAM: 1 GiB Video device 'ipu@2400000' cannot allocate frame buffer memory -ensure the device is set up before relocation Error binding driver 'ipuv3_video': -28 Video device 'ipu@2800000' cannot allocate frame buffer memory -ensure the device is set up before relocation Error binding driver 'ipuv3_video': -28 Some drivers failed to bind Error binding driver 'generic_simple_bus': -28 Some drivers failed to bind initcall sequence 4ffe4500 failed at call 1780dfb7 (err=-28) " 1. fdtdec_get_alias_seq will use "video" as base, however in alias node, we use ipux, so add new alias for U-Boot dts. 2. DM_VIDEO is enabled, however reserve_video is called before relocation, so to make DM_VIDEO work before relocation, need to set SYS_MALLOC_F_LEN 3. defconfig is updated with savedefconfig Note: I do not have a video panel to test, but with this patch, U-Boot boots up again, below log. " U-Boot SPL 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800) Trying to boot from MMC1 U-Boot 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800) CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 34C Reset cause: POR Model: Freescale i.MX6 Quad SABRE Smart Device Board Board: MX6-SabreSD I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3 Loading Environment from MMC... *** Warning - bad CRC, using default environment PCI: pcie phy link never came up In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 " Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
* Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan2019-05-041-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
* configs: move CONFIG_SPL_TEXT_BASE to KconfigSimon Goldschmidt2019-04-291-0/+1
| | | | | | | | | Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2019-04-291-2/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* mx6sabresd: convert to DM_VIDEOAnatolij Gustschin2019-04-131-1/+1
| | | | | | Enable DM_VIDEO in defconfig. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* imx: move CONFIG_VIDEO_IPUV3 to defconfigsAnatolij Gustschin2019-04-131-0/+1
| | | | Signed-off-by: Anatolij Gustschin <agust@denx.de>
* Convert CONFIG_SF_DEFAULT_* to KconfigPatrick Delaunay2019-03-251-0/+2
| | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
* configs: Resync with savedefconfigTom Rini2019-02-221-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: mx6sabresd: Reduce SPL size by disabling DOS, EXT and EFI supportAbel Vesa2019-02-151-0/+2
| | | | | | | | | | With DM and FIT enabled in SPL, there is an sram overflow. By disabling CONFIG_SPL_DOS_PARTITION, CONFIG_SPL_EXT_SUPPORT and CONFIG_SPL_EFI_PARTITION, we get to keep the 'one binary to fit all' for imx6[q|qp|dl] on sabresd since the final SPL image is now under 64KB. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
* configs: mx6sabresd: Add DM_SPI_FLASH necessary configsAbel Vesa2019-02-151-0/+2
| | | | | | | | Enable all neceassary configs to support DM_SPI_FLASH on mx6sabresd. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
* mx6sabresd: Add DM_GPIO supportAbel Vesa2019-02-151-0/+1
| | | | | | | | | Add the DM_GPIO related config for mx6sabresd. Also add the gpio request calls. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
* configs: mx6sabresd: Add SPL FIT and DM supportAbel Vesa2019-02-151-2/+18
| | | | | | | | Enable all the necessary configs for SPL DM and FIT support for mx6sabresd. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
* spl: Kconfig: Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPL_FS_EXT4Tien Fong Chee2019-02-011-1/+1
| | | | | | | | | Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be used to control the build in both SPL and U-Boot. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* Kconfig: Migrate BOUNCE_BUFFERPhilipp Tomsich2019-01-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | The bounce buffer is used by a few drivers (most of the MMC drivers) to overcome limitations in their respective DMA implementation. This moves the configuration to Kconfig and makes it user-selectable (even though it will be a required feature to make those drivers work): the expected usage is for drivers depending on this to 'select' it unconditionally from their respective Kconfig (see follow-up patches). This commit includes a full migration using moveconfig.py to ensure that each commit compiles. To ensure bisectability we update dependencies of various drivers to now select BOUNCE_BUFFER when needed. [trini: Squash all patches to ensure bisectability] Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion] Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion] Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
* Kconfig: rename CONFIG_SPL_USB_GADGET_SUPPORT as CONFIG_SPL_USB_GADGETJean-Jacques Hiblot2019-01-101-1/+1
| | | | | | | The SPL option for USB gadget should be named after the option for u-boot (CONFIG_USB_GADGET) Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
* Convert CONFIG_MII et al to KconfigAdam Ford2018-08-171-0/+1
| | | | | | | | | | This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini2018-08-161-0/+1
| | | | | | | | | | | We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2018-06-041-7/+7
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* fastboot: Move fastboot to drivers/fastbootAlex Kiernan2018-05-301-1/+1
| | | | | | | | | | | | | | Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to drivers/fastboot. Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing behaviour. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* Convert CONFIG_SPI to KconfigAdam Ford2018-04-271-0/+1
| | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to KconfigAlex Kiernan2018-04-081-0/+1
| | | | | | | | | Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
* treewide: Migrate CONFIG_FSL_ESDHC to KconfigMario Six2018-04-081-0/+1
| | | | | | Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* configs: Resync with savedefconfigTom Rini2018-04-071-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge git://git.denx.de/u-boot-imxTom Rini2018-02-251-0/+1
|\
| * mx6sabresd: Select the CONFIG_EFI_PARTITION optionFabio Estevam2018-02-181-0/+1
| | | | | | | | | | | | | | With fastboot support enabled, it is useful to be able to list the eMMC EFI partitions, so select the CONFIG_EFI_PARTITION option. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* | Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford2018-02-231-0/+1
|/ | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* spi: Migrate CONFIG_MXC_SPI to KconfigTuomas Tynkkynen2018-02-131-0/+1
| | | | Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
* configs: Migrate CONFIG_SYS_TEXT_BASETom Rini2018-02-111-0/+1
| | | | | | | | | | | On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2018-02-101-2/+0
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* mx6sabresd: Add fastboot supportFabio Estevam2018-02-041-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | fastboot tool is a convenient way to flash the eMMC, so add support for it. Examples of usages: On the mx6sabresd: => fastboot 0 On the Linux PC connected via USB: $ sudo fastboot getvar bootloader-version -i 0x0525 bootloader-version: U-Boot 2018.01-00550-g7517cfe finished. total time: 0.000s $ sudo fastboot reboot -i 0x0525 (this causes the mx6sabresd to reboot) Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Shawn Guo <shawn.guo@linaro.org>
* mx6sabresd: Select CONFIG_CMD_USB_MASS_STORAGEFabio Estevam2018-02-041-0/+1
| | | | | | Select CONFIG_CMD_USB_MASS_STORAGE so that the 'ums' can be used. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* imx: Unify CONFIG_BOOTDELAYFabio Estevam2017-12-291-1/+0
| | | | | | | | | In order to provide a consistent user experience for imx board users, remove the custom CONFIG_BOOTDELAY values from defconfig files, so that all boards can use the default two second delay. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
* mx6: Select MX6QDL option via KconfigFabio Estevam2017-11-201-1/+1
| | | | | | | Currently the MX6QDL option is selected via CONFIG_SYS_EXTRA_OPTIONS, but it is better to select it directly via Kconfig. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* configs: Resync with savedefconfigTom Rini2017-10-301-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen2017-10-101-1/+0
| | | | | | | | | | | | | | Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
* usb: gadget: Make g_dnl USB settings commonMaxime Ripard2017-10-031-3/+3
| | | | | | | | | | | The g_dnl USB settings for the vendor ID, product ID and manufacturer are actually common settings that can and should be shared by all the gadgets. Make them common by renaming them, and convert all the users. Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* mx6sabresd: Add Serial Download Protocol supportFabio Estevam2017-09-201-0/+4
| | | | | | | | Add Serial Download Protocol support (SDP), which allows loading SPL and u-boot.img via imx_usb_loader tool as explained in doc/README.sdp. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* usb: net: migrate USB Ethernet adapters to KconfigChris Packham2017-09-081-0/+1
| | | | | | | | This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig. Update defconfigs. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
View Lorry Controller Status