| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
| |
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
| |
|
|
|
|
| |
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
| |
|
|
|
|
| |
Move this header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
| |
|
|
|
|
|
| |
Apply u-boot coding style on include files order as described by the
wiki https://www.denx.de/wiki/U-Boot/CodingStyle.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
| |
|
|
|
|
|
| |
Fix the macro to set the pplmsb field (bit 3) of the RASTER_TIMING_0
register. It is used in order to support up to 2048 pixels per line.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Update the driver to support the device tree and the driver model.
Timings and panel parameters are now loaded from the device tree.
The DM code replaces the am335x_lcdpanel structure with
tilcdc_panel_info taken from the linux kernel, as well the management
of additional parameters not covered in the legacy code. In addition,
the am335x_lcdpanel structure contains parameters and operations that
were probably a requirement of the board for which this driver was
developed and which, however, were not developed in the linux kernel.
All this led to rewrite th DM controller initialization code, except
for the pixel clock setting that is executed in a function created in a
previous patch with code taken from the legacy am335xfb_init.
The patch has been tested on a custom board with u-boot 2018.11-rc2 and
the following device-tree configuration:
panel {
compatible = "ti,tilcdc,panel";
pinctrl-names = "default";
pinctrl-0 = <&lcd_enable_pins>;
enable-gpios = <&gpio0 31 0>;
backlight = <&backlight>;
status = "okay";
u-boot,dm-pre-reloc;
panel-info {
ac-bias = <255>;
ac-bias-intrpt = <0>;
dma-burst-sz = <16>;
bpp = <16>;
fdd = <0x80>;
sync-edge = <0>;
sync-ctrl = <1>;
raster-order = <0>;
fifo-th = <0>;
};
display-timings {
native-mode = <&timing0>;
timing0: 800x480 {
hactive = <800>;
vactive = <480>;
hback-porch = <46>;
hfront-porch = <210>;
hsync-len = <20>;
vback-porch = <23>;
vfront-porch = <22>;
vsync-len = <10>;
clock-frequency = <33000000>;
hsync-active = <0>;
vsync-active = <0>;
};
};
};
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
|
| |
|
|
|
|
|
| |
Created in preparation to support driver-model, they can also be called
from legacy code. In this way, code duplication is avoided.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
| |
|
|
|
|
|
|
|
| |
In case of null error, round rate is equal to target rate, so it is
useless to continue to search the DPLL setup parameters to get the
desidered pixel clock rate.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
| |
|
|
|
|
|
| |
"DISP" -> "DIV"
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
| |
|
|
|
|
| |
Add more clarity by prefixing the name of the register to the bitfields.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
| |
|
|
|
|
| |
Arrange the bitfields of each register in the ascending order.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
| |
|
|
|
|
| |
Use one space around (on each side of) the binary '-' operator.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
| |
|
|
|
|
|
| |
Add, if missing, the bitfield masks in the setting macros of the LCD
controller registers.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
| |
|
|
|
|
| |
Use the standard BIT() and GENMASK() macros for bitfield definitions.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The LCDC IP-core an be feed from several clock sources, one of those is
a dedicated DPLL for generating a dividable base-clock for this IP-core.
The TRM specifies the maximum input frequency for the LCCD with 200 MHz,
so we must not exceed this value with the PLL frequency (which can lock
much higher).
This patch tries every combination of multipliers and divisors of the
PLL and the IP-core itself for getting as near as possible the the
requested panel->pxl_clk.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
| |
|
|
|
| |
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
| |
|
|
|
| |
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The DMA was outputting the palette on the screen because the base
for the DMA was not after the palette. In addition to that, the ceiling was
also too high, this led that the output on the screen was shifted.
NOTE: According to the TRM, even in 16/24bit mode a palette is required
in the first 32 bytes of the framebuffer.
See also:
https://e2e.ti.com/support/arm/sitara_arm/f/791/p/234967/834483#834483
"In this mode, the LCDC will assume all information is data and thus you
need to ensure that the DMA points to the first pixel of data and not the
first entry in the frame buffer which is the beginning of the 512 byte
palette."
Signed-off-by: Martin Pietryka <martin.pietryka@chello.at>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
To support 16bpp we just need to change the raster_ctrl register
accordingly. Also 32bpp mode should work as well, but was not tested.
According to the TRM the uppermost byte will be ignored when
LCD_TFT_24BPP_UNPACK is set.
The switch logic is based on the Linux kernel tilcdc driver:
drivers/gpu/drm/tilcdc/tilcdc_crtc.c: lines 407 through 419
(kernel was checked out at commit: bcc981e9ed8)
Signed-off-by: Martin Pietryka <martin.pietryka@chello.at>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
| |
|
|
|
|
|
| |
According to the TRM you have to set bits [21:20] to 0b10 for RAW mode, so
(0x10 << 20) is obviously wrong here.
Signed-off-by: Martin Pietryka <martin.pietryka@chello.at>
|
| |
|
|
|
|
|
|
|
|
|
| |
Since i've been married, i also have a new surname.
Mr. Petermaier moved to Mr. Schmelzer.
In this patch i update all files in which my (old) name is present.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Often on boards exists a circuit which switches power on/off to LCD display.
Due to the need of limiting the in-rush current the output voltage from this
circuit rises "slowly", so it is necessary to wait a bit (VCC ramp up time)
before starting output on LCD-pins.
This time is specified in <n> ms within the panel-settings, called "pup_delay"
Further some LCDs need a couple of frames to stabilize the image on it.
We have now the possibility to wait some time after starting output on LCD.
This time is also specified in <n> ms within panel-settings, called "pon_delay"
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
|
|
|
- Adds support for a minimal framebuffer driver of TI's AM335x SoC
to be compatible with Wolfgang Denk's LCD-Framework (CONFIG_LCD,
common/lcd.c)
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
|
