summaryrefslogtreecommitdiff
path: root/include/configs/ids8313.h
Commit message (Collapse)AuthorAgeFilesLines
* common: Drop linux/stringify.h from common headerSimon Glass2020-05-181-0/+2
| | | | | | Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
* treewide: mem: Move mtest related defines to KconfigWIP/2020-05-07-more-kconfig-migrationsAshok Reddy Soma2020-05-081-3/+0
| | | | | | | | | | | Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
* powerpc: mpc83xx: convert CONFIG_FSL_ELBC to KconfigRasmus Villemoes2020-01-081-2/+0
| | | | | | | | This complements commit 068789773d0 which did the conversion for mpc85xx. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Mario Six <mario.six@gdsys.cc>
* env: Finish migration of common ENV optionsTom Rini2019-11-201-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND checkTom Rini2019-11-201-1/+0
| | | | | | | | | | | | | | | We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one board where we can simply multiple CONFIG_ENV_SIZE by two for the same result. The other place where we could but were not previously using this is for where env_internal.h checks for if we should set ENV_IS_EMBEDDED. This seems like the most likely use, historically, of the variable, but it was not used. Add logic to check for this now. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to KconfigSimon Glass2019-08-021-4/+0
| | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_USE_PREBOOT CONFIG_PREBOOT Both are together in one commit, since otherwise the former causes kconfig to define the latter, which gives duplicate symbol errors. Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the backslash lands in the wrong place. Similarly with socfpga_vining_fpga. Signed-off-by: Simon Glass <sjg@chromium.org>
* Add CONFIG_USE_PREBOOT to boards that use CONFIG_PREBOOTSimon Glass2019-08-021-0/+1
| | | | | | | In order to use CONFIG_PREBOOT with Kconfig, CONFIG_USE_PREBOOT must be defined for each board. To prepare for conversion to Kconfig, add this. Signed-off-by: Simon Glass <sjg@chromium.org>
* mpc83xx: Get rid of CONFIG_SYS_LBC_*Mario Six2019-05-211-9/+0
| | | | | | | | | | | | | | | | Except for one counter example, CONFIG_SYS_LBC_LBCR always has a value of either 0x00040000 or 0x00000000. CONFIG_SYS_LBC_MRTPR always has the value 0x20000000. CONFIG_SYS_LBC_LSDMR_{1,2,4,5} are not set for any mpc83xx board. CONFIG_SYS_LBC_LSRT is set by one board (to 0x32000000). To simplify the configuration files, hardcode the setting of these values for mpc83xx. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Get rid of CONFIG_SYS_DDR_SDRAM_BASEMario Six2019-05-211-1/+0
| | | | | | | | CONFIG_SYS_DDR_SDRAM_BASE is set to the same value as CONFIG_SYS_SDRAM_BASE on all existing boards. Just use CONFIG_SYS_SDRAM_BASE instead. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Get rid of CONFIG_SYS_DDR_BASEMario Six2019-05-211-3/+2
| | | | | | | CONFIG_SYS_DDR_BASE is specific to mpc83xx an is always set to the same value as CONFIG_SYS_SDRAM_BASE. Just use CONFIG_SYS_SDRAM_BASE instead. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate CONFIG_LCRR_* to KconfigMario Six2019-05-211-2/+0
| | | | | | Migrate the CONFIG_LCRR_* settings to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate arbiter config to KconfigMario Six2019-05-211-3/+0
| | | | | | Migrate the arbiter configuration to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate CONFIG_SYS_IMMR to KconfigMario Six2019-05-211-2/+0
| | | | | | Migrate CONFIG_SYS_IMMR to Kconfig for MPC83xx. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate HID config to KconfigMario Six2019-05-211-7/+0
| | | | | | Mirate the HID configuration settings to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate CONFIG_SYS_{BR, OR}*_PRELIM to KconfigMario Six2019-05-211-12/+0
| | | | | | | | | | | Migrate the BR/OR settings to Kconfig. These must be known at compile time, so cannot be configured via DT. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Simplify BR,OR linesMario Six2019-05-211-36/+11
| | | | | | | Re-format all BR,OR #define lines into single lines. This makes them harder to read, but accessible to semi-automatic replacement. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Normalize BR/OR option linesMario Six2019-05-211-5/+5
| | | | | | | | | | | | All BR/OR option lines should have the same layout to make them easier to migrate to Kconfig. This includes using the same option macros everywhere. The normalize the lines, * replace function macros with their results, and * replace hardcoded hex values with standard macros Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate LBLAW_* to KconfigMario Six2019-05-211-12/+0
| | | | | | | | | | | | The LBLAW_* values determine the window configuration of the memory controller. Hence, they must be known at compile time, and cannot be implemented in the DT mechanism. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate BATS config to KconfigMario Six2019-05-211-77/+0
| | | | | | | | | | | | The BATs (block address translation registers) determine the initial memory window mappings. Hence, they must be known at compile time and cannot be implemented in the DT mechanism. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* powerpc: Migrate HIGH_BATS to KconfigMario Six2019-05-211-1/+0
| | | | | | Migrate the CONFIG_HIGH_BATS variable to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Kconfig: Migrate HRCW to KconfigMario Six2019-05-211-21/+0
| | | | | | | | | | | | | The HRCW (hardware reset configuration word) is a constant that must be hard-coded into the boot loader image. So, it must be available at compile time, and cannot be migrated to the DT mechanism, but has to be kept in Kconfig. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Get rid of CONFIG_83XX_CLKINMario Six2019-05-211-3/+0
| | | | | | | | | | | | | MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the system clock. To migrate the architecture, we can replace CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ. To do this * replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ * set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all MPC83xx config files Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Replace CONFIG_83XX_CLKIN in calculationsMario Six2019-05-211-1/+1
| | | | | | | | | | | | | | | | | | CONFIG_SYS_CLK_FREQ is the standard way to set the system clock frequency. On MPC83xx, CONFIG_83XX_CLKIN is used for this purpose. Hence, the obvious way is to replace CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ. A few MPC83xx boards use the CONFIG_83XX_CLKIN variable for computing CONFIG_SYS_NS16550_CLK. This makes it harder to replace CONFIG_83XX_CLKIN. But the value of the multiplicator can be read from the SPMR register. Hence, replace the static calculations with a call to a new get_bus_freq function, as other architectures do. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Introduce ARCH_MPC831*Mario Six2019-05-201-3/+0
| | | | | | Replace CONFIG_MPC833* with proper CONFIG_ARCH_MPC833* Kconfig options. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* spi: Zap CONFIG_HARD_SPIJagan Teki2018-11-271-10/+0
| | | | | | | | | | In legacy CONFIG_HARD_SPI initalizing spi_init code, which was removed during dm conversion cleanup. So remove the dead instances of CONFIG_HARD_SPI, and related code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* Convert CONFIG_FLASH_CFI_DRIVER et al to KconfigAdam Ford2018-10-191-5/+0
| | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_MISC_INIT_R to KconfigAdam Ford2018-08-171-2/+0
| | | | | | | | | This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_MII et al to KconfigAdam Ford2018-08-171-1/+0
| | | | | | | | | | This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford2018-07-221-2/+0
| | | | | | | | This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
* SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini2018-05-071-2/+1
| | | | | | | | | | | | | | | | | | | | When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
* Migrate IMAGE_FORMAT_LEGACY to KconfigAlex Kiernan2018-04-281-2/+0
| | | | | | | This converts IMAGE_FORMAT_LEGACY to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* treewide: Convert CONFIG_HOSTNAME to a string optionMario Six2018-04-081-1/+1
| | | | | | | | | CONFIG_HOSTNAME is defined as a "plain" preprocessor string, but every use is couched by __stringify(...). Hence, convert it to a proper string option. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* treewide: Migrate CONFIG_TSEC_ENET to KconfigMario Six2018-04-081-1/+0
| | | | | | Migrate the CONFIG_TSEC_ENET option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* Convert all of CONFIG_CONS_INDEX to KconfigTom Rini2018-03-161-1/+0
| | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com>
* bootcount: Migrate CONFIG_SYS_BOOTCOUNT_ADDRTom Rini2018-02-251-3/+0
| | | | | | | | | | | | | | Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig. We can provide a default for BOOTCOUNT_AM33XX as that's a specific part of the RTC in use. We can also provide a default for ARCH_LS1043A and ARCH_LS1021A as they had been previously calculated and their symbols are in Kconfig. In the case of other QE-enabled platforms, they are not so we must update the relevant defconfig files. The previous default only applied in some cases, even on a specific SoC family. Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* Migrate CONFIG_BOOTCOUNT_ALEN to KconfigAlex Kiernan2018-02-241-1/+0
| | | | | Convert CONFIG_BOOTCOUNT_ALEN to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
* Convert CONFIG_BOOTCOUNT_I2C to KconfigAlex Kiernan2018-02-241-1/+0
| | | | | | | | This converts the following to Kconfig: CONFIG_BOOTCOUNT_I2C Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
* Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford2018-02-231-6/+0
| | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_BOOTCOUNT_LIMIT to KconfigLukasz Majewski2018-02-151-1/+0
| | | | | | | | | | This converts the following to Kconfig: CONFIG_BOOTCOUNT_LIMIT Signed-off-by: Lukasz Majewski <lukma@denx.de> Tested-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
* spi: Migrate CONFIG_MPC8XXX_SPI to KconfigTuomas Tynkkynen2018-02-131-1/+0
| | | | Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
* powerpc: Drop unreferenced CONFIG_* definesTuomas Tynkkynen2018-01-191-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | The following config symbols are only defined once and never referenced anywhere else: CONFIG_CYRUS CONFIG_IDS8313 CONFIG_MPC8308_P1M CONFIG_MPC8308RDB CONFIG_MPC8349EMDS CONFIG_MPC8349ITXGP CONFIG_SBC8349 CONFIG_SBC8548 CONFIG_SBC8641D CONFIG_TQM834X CONFIG_VE8313 CONFIG_XPEDITE5140 CONFIG_XPEDITE5200 CONFIG_XPEDITE550X Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Acked-by: Mario Six <mario.six@gdsys.cc>
* Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULTTom Rini2017-11-051-7/+2
| | | | | | | | | | We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: Tom Rini <trini@konsulko.com>
* include/configs: drop default definitions of CONFIG_SYS_MAXARGSThomas Petazzoni2017-09-031-1/+0
| | | | | | | | | Now that include/config_fallbacks.h define a sane fallback for CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all configurations that were using the default value. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* include/configs: drop default definitions of CONFIG_SYS_PBSIZEThomas Petazzoni2017-09-031-2/+0
| | | | | | | | | Now that the fallback value of CONFIG_SYS_PBSIZE in include/config_fallbacks.h has been adjusted, remove its definition from a large number of board configuration files. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* common: Move CONFIG_BOOTARGS to KconfigSam Protsenko2017-08-141-1/+0
| | | | | | | | | Also introduce CONFIG_USE_BOOTARGS option so we can control if CONFIG_BOOTARGS defined at all. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> [trini: Resync r8a779[56]_ulcb, various ls10xx targets] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate CMD_NAND*Tom Rini2017-07-311-2/+0
| | | | | | | | | | Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the defconfig files. Tested-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* Convert CONFIG_ENV_IS_IN_FLASH to KconfigSimon Glass2017-07-251-1/+0
| | | | | | | This converts the following to Kconfig: CONFIG_ENV_IS_IN_FLASH Signed-off-by: Simon Glass <sjg@chromium.org>
* configs: Migrate RBTREE, LZO, CMD_MTDPARTS, CMD_UBI and CMD_UBIFSTom Rini2017-07-241-4/+0
| | | | | | | | The above CONFIG options are in Kconfig, and now have correct depends and inter-dependencies. Migrate these to configs/ from include/configs/. In the case of CMD_UBIFS also change it to be a default y if CMD_UBI. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_CMD_JFFS2 to KconfigSimon Glass2017-05-221-1/+0
| | | | | | | This converts the following to Kconfig: CONFIG_CMD_JFFS2 Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_CMD_HASH to KconfigSimon Glass2017-05-221-1/+0
| | | | | | | | | | This converts the following to Kconfig: CONFIG_CMD_HASH Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Rework slightly, enable on some boards again] Signed-off-by: Tom Rini <trini@konsulko.com>
View Lorry Controller Status