summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeFilesLines
* ARM: vf610: move to standard arch/board approachStefan Agner2017-03-193-5/+0
| | | | | | | | Move Freescale/NXP Vybrid to a standard arch/board approach, similar to what has been done to i.MX 6 earlier in commit 89ebc82137be ("ARM: mx6: move to a standard arch/board approach"). Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
* imx: ventana: use mmc_root in boot scriptsTim Harvey2017-03-191-2/+2
| | | | | Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
* imx: ventana: config: add gzwrite supportTim Harvey2017-03-191-0/+1
| | | | | Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
* colibri_imx7: split and resize firmware MTD partitionStefan Agner2017-03-191-2/+4
| | | | | | | | | | | | | Use two separate partitions for the two firmware instances. Also resize them to be of the same size which also makes the start of the UBI partition nicely aligned to 0x400000. In order to detect the new MTD layout and whether we run a U-Boot with the new BCB format or not, introduce a variable called "updlevel" which we can use in update/upgrade scripts. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
* colibri_imx7: use device-tree for MTD partitionsStefan Agner2017-03-191-1/+1
| | | | | | | Use device-tree fixup to communicate the MTD partitions to the kernel. Remove mtdparts from the kernel command line. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
* colibri_imx7/colibri_imx6/apalis_imx6: limit bootm memoryStefan Agner2017-03-193-0/+3
| | | | | | | | | | | | | | | | | | | | Limit memory used for relocation of FDT or initrd. This is required to make sure that relocated artifacts are within lowmem. If fdt_high or initrd_high are not set, U-Boot automatically relocates artifacts to the end of memory. But this area won't be part of lowmem and hence will not be accessible by the kernel during early boot. With VM split set to 2G/2G (i.MX default), only the 2GB Apalis iMX6 is affected by that issue. With VM split set to 3G/1G (ARM default) also modules with 1GB of memory are affected. With the latter the amount of lowmem will be 760MiB. The value must also not exceed available memory! Use a safe value of 512MiB for Apalis and 256MiB for Colibri. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
* arm: i.MX6UL: add Armadeus Systems OPOS6UL SoM and OPOS6ULDev carrier boardSébastien Szymanski2017-03-191-0/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet phy. OPOS6ULDev is carrier board for the OPOS6UL. U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09) Trying to boot from MMC1 U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100) CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 40C Reset cause: POR Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board DRAM: 256 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Video: 800x480x18 In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* MCCMON6: defconfig: Move 'quiet' console parameter to 'console' env variableLukasz Majewski2017-03-191-2/+2
| | | | Signed-off-by: Lukasz Majewski <lukma@denx.de>
* arm: imx6: tqma6: add support for TQMa6DL variantMarkus Niebel2017-03-172-6/+9
| | | | | | | | This adds support for TQMa6DL using i.MX6DL and 1GiB DRAM Since The module will use the same devicetree, we patch the ram size in ft_board_setup. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
* arm: imx6: tqma6: use CONFIG_TQM6x for SOM specific settingsMarkus Niebel2017-03-171-4/+4
| | | | | | | | We have a Kconfig name for the module types. Let's Use it. Some feature selections and configurations are based on the module. Module selection selects the CPU type. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
* i.MX6Q: icorem6_rqs: Add mmc_late_initJagan Teki2017-03-171-2/+0
| | | | | | | | | | | Let the runtime code can set the mmcdev and mmcroot based on the devno using mmc_get_env_dev instead of defining separately in build-time configs using mmc_late_init func. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* i.MX6Q: icorem6_rqs: Add modeboot env via board_late_initJagan Teki2017-03-171-16/+16
| | | | | | | | | | | Add runtime, modeboot env which is setting mmcboot based on the bootdevice so-that conditional macros for MMC via CONFIG_BOOTCOMMAND should be avoided in config files. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: icorem6_rqs: Add eMMC boot supportJagan Teki2017-03-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from eMMC: -------------- U-Boot SPL 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21) Trying to boot from MMC2 U-Boot 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21 +0100) CPU: Freescale i.MX6D rev1.2 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial switch to partitions #0, OK mmc1(part 0) is current device Net: No ethernet found. Hit any key to stop autoboot: 0 Booting from mmc ... switch to partitions #0, OK mmc1(part 0) is current device Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* i.MX6UL: isiot: Add mmc_late_initJagan Teki2017-03-171-2/+0
| | | | | | | | | | | Let the runtime code can set the mmcdev and mmcroot based on the devno using mmc_get_env_dev instead of defining separately in build-time configs using mmc_late_init func. Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed by: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* i.MX6UL: isiot: Add modeboot env via board_late_initJagan Teki2017-03-171-20/+16
| | | | | | | | | | | | Add runtime, modeboot env which is setting mmcboot, or nandboot based on the bootdevice so-that conditional macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should be avoided in config files. Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed by: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* i.MX6UL: isiot: Add eMMC boot supportJagan Teki2017-03-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from eMMC: -------------- U-Boot SPL 2017.01-00314-gd0cd9cd-dirty (Jan 25 2017 - 13:25:27) Trying to boot from MMC2 U-Boot 2017.01-00314-gd0cd9cd-dirty (Jan 25 2017 - 13:25:27 +0100) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 36C Reset cause: POR Model: Engicam Is.IoT MX6UL eMMC Starterkit DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial switch to partitions #0, OK mmc1(part 0) is current device Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed by: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: isiotmx6ul: Add nandboot env supportJagan Teki2017-03-171-1/+31
| | | | | | | | | Add config options for booting Linux from NAND in UBI format. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: isiotmx6ul: Add NAND supportJagan Teki2017-03-171-1/+24
| | | | | | | | | Add NAND support for Engicam Is.IoT MX6UL board. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx6: isiotmx6ul: Add FEC supportJagan Teki2017-03-171-0/+10
| | | | | | | | | Add FEC support for Engicam Is.IoT MX6UL module. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* arm: imx6ul: Add Engicam Is.IoT MX6UL Starter Kit initial supportJagan Teki2017-03-171-0/+142
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from MMC: ------------- U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33) Trying to boot from MMC1 U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 33C Reset cause: POR Model: Engicam Is.IoT MX6UL Starterkit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 isiotmx6ul> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* configs: imx6: Don't define USDHC2_BASE_ADDRJagan Teki2017-03-172-2/+2
| | | | | | | | | | | USDHC base address will assigned by SPL using fsl_esdhc_initialize and u-boot with devicetree, hence no remove base address assignment in config files. Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* imx: mx7ulp_evk: enable mmc/regulator supportPeng Fan2017-03-171-1/+90
| | | | | | | | | | | Enable MMC support. The fsl sdhc driver needs regulator to enable power, so enable regulator support. And bootcmd and more env. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: imx7ulp: add EVK board supportPeng Fan2017-03-171-0/+109
| | | | | | | | | | | | | | | | | | | | | | | | Add EVK board support. Add the evk dts file. LOG: U-Boot 2017.03-rc2-00038-gab86c1d (Feb 22 2017 - 15:59:58 +0800) CPU: Freescale i.MX7ULP rev1.0 at 500 MHz Reset cause: POR Boot mode: Dual boot Model: NXP i.MX7ULP EVK DRAM: 1 GiB MMC: FSL_SDHC: 0 In: serial@402D0000 Out: serial@402D0000 Err: serial@402D0000 Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* igep00x0: disable environmentLadislav Michl2017-03-141-1/+1
| | | | | | | | | | | | | ISEE's U-Boot and Linux are using 1bit ECC scheme, while we switched to 8bit ECC to fullfill flash specification requirements. However when trying to run U-Boot on board with 1bit ECC'd data on flash, UBI code takes several minutes to pass scan as reading of every block ends with ecc error (which is also printed on console). So, until proper solution is developed, disable environment alltogether. Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
* board: Add STMicroelectronics STiH410-B2260 supportPatrice Chotard2017-03-141-0/+60
| | | | | | | | | | | | | | | | | | | This is a 96Board compliant board based on STiH410 SoC: - 1GB DDR - On-Board USB combo WiFi/Bluetooth RTL8723BU with PCB soldered antenna - Ethernet 1000-BaseT - SATA - HDMI - 2 x USB2.0 type A - 1 x USB2.0 type micro-AB - SD card slot - High speed connector (SD/I2C/USB interfaces) - Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces) Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* ARM: Migrate errata to KconfigTom Rini2017-03-0917-74/+0
| | | | | | | | | This moves all of the current ARM errata from various header files and in to Kconfig. This allows for a minor amount of cleanup as we had some instances where both a general common header file was enabling errata as well as the board config. We now just select these once at the higher level in Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* Freescale/NXP: Migrate CONFIG_FSL_CAAM to defconfigsTom Rini2017-03-0923-31/+0
| | | | | | | | | | | | | | | | | | | | | | In some cases this is absolutely required, so select this for some secure features. This also requires migration of RSA_FREESCALE_EXP Cc: Ruchika Gupta <ruchika.gupta@nxp.com> Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: Naveen Burmi <NaveenBurmi@freescale.com> Cc: Po Liu <po.liu@freescale.com> Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com> Cc: Priyanka Jain <Priyanka.Jain@freescale.com> Cc: Sumit Garg <sumit.garg@nxp.com> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Cc: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Feng Li <feng.li_2@nxp.com> Cc: Alison Wang <alison.wang@freescale.com> Cc: Mingkai Hu <Mingkai.Hu@freescale.com> Cc: York Sun <york.sun@nxp.com> Cc: Saksham Jain <saksham.jain@nxp.freescale.com> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2017-02-272-16/+20
|\
| * tqma6: [cosmetic] sanitize environment definesMarkus Niebel2017-02-191-1/+1
| | | | | | | | Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
| * tqma6: fix rounding in envMarkus Niebel2017-02-191-6/+6
| | | | | | | | | | | | | | need to add before div in mmc update scripts. Otherwise we could write one block more ba acident Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
| * mx6: tqma6: add rootfsmode environment for mmc / sdMarkus Niebel2017-02-191-1/+3
| | | | | | | | Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
| * mx6: tqma6: fix typo in envMarkus Niebel2017-02-191-1/+1
| | | | | | | | | | | | there was a double bracketed var ref. fix this. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
| * imx6: tqma6: rely on default setting for tftp and nfsMarkus Niebel2017-02-191-4/+0
| | | | | | | | | | | | | | Playing with USB-to-Ethernet dongles it turns out, that these will not work with special settings Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
| * arm: imx6: tqma6: add configurable CMA sizeMarkus Niebel2017-02-191-2/+7
| | | | | | | | | | | | | | | | depending on the use case different CMA sizes are needed for linux. Add env var to enable passing CMA size via kernel command line Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
| * mx6sx: udoo_neo: use different load address for ramdiskPeter Robinson2017-02-191-1/+1
| | | | | | | | | | | | | | | | The fdt_addr and ramdisk_addr_r are currently both defined to 0x83000000 and that's not going to work well for anyone. Move the ramdisk_addr_r to 0x84000000. Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
| * mx6sx: udoo_neo: Define the default serial consolePeter Robinson2017-02-191-0/+1
| | | | | | | | | | | | | | | | Standard boot processes including distro boot generally expect the default console to be defined. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Breno Lima <breno.lima@nxp.com>
* | ARM: uniphier: rename second stage loader nameMasahiro Yamada2017-02-231-1/+1
| | | | | | | | | | | | | | | | | | For the memory footprint reason, the Boot ROM can not load the ARM Trusted Firmware BL1 directly when Trusted Board Boot is enabled. The second stage loader is Socionext's own firmware, so rename it for clarification. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | Drop CONFIG_ENABLE_VBOOTTom Rini2017-02-171-2/+0
|/ | | | | | This is no longer used anywhere. Signed-off-by: Tom Rini <trini@konsulko.com>
* SPL: Move SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to KconfigDalon Westergreen2017-02-174-7/+0
| | | | | | | | | | | Added SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to Kconfig. Due to SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION being moved to Kconfig the board defconfigs for db-88f6820-gp_defconfig kc1_defconfig and sniper_defconfig need to be updated. Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
* Merge tag 'xilinx-fixes-for-v2017.03' of git://www.denx.de/git/u-boot-microblazeTom Rini2017-02-131-1/+1
|\ | | | | | | | | | | | | | | Xilinx fixes for v2017.03 - defconfig alignment - Topic.nl board updates - Minor microblaze comment fix
| * configs/topic_miami.h: Correct kernel_size in default environmentMike Looijmans2017-02-101-1/+1
| | | | | | | | | | | | | | | | | | The kernel partition in QSPI is 0x440000 large, not 0x400000. Fix this in the environment, otherwise the kernel will fail to boot if it occupies more space. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | flash: complete CONFIG_SYS_NO_FLASH move with renamingMasahiro Yamada2017-02-12240-492/+54
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | rockchip: rename miniarm to tinker boardEddie Cai2017-02-091-0/+0
| | | | | | | | | | | | | | | | Miniarm is the internal project code. Now it is officially named Tinker board. So rename it. Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | rockchip: firefly: configs: use spl back to bromJacob Chen2017-02-091-5/+0
| | | | | | | | | | | | | | Keep it same with other boards otherwise i have to write special script for it.. Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | rockchip: configs: move env offset to common headerJacob Chen2017-02-097-84/+14
|/ | | | | | | To reduce redundant code. Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Remove unused symbol CONGIG_CMD_STORAGE from board configsLars Poeschel2017-02-084-7/+0
| | | | | | | | Albeit it's a typo, neither CONGIG_CMD_STORAGE nor CONFIG_CMD_STORAGE are used anywhere, so remove the define from the board configs. Signed-off-by: Lars Poeschel <poeschel@lemonage.de> Reviewed-by: Tom Rini <trini@konsulko.com>
* cmd: move CONFIG_CMD_UNZIP and CONFIG_CMD_ZIP to KconfigMasahiro Yamada2017-02-087-11/+0
| | | | | | | | | | | | | | CONFIG_CMD_ZIP is not defined by any board. I am moving CONFIG_CMD_UNZIP to defconfig files except UniPhier SoC family. I am the maintainer of UniPhier platform, so I know "select CMD_UNZIP" is better for this platform. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Ryan Harkin <ryan.harkin@linaro.org> Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
* keystone2: Rename local CONFIG_ symbolPhil Edworthy2017-02-081-2/+2
| | | | | | CONFIG_SPL_STACK_SIZE is not a config option, so rename it. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
* api: Convert to KconfigEmmanuel Vadot2017-02-082-7/+0
| | | | | | | | | Now that we have a Kconfig for the API, convert the two boards that are using this to Kconfig and remove CONFIG_API from the whitelist. Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* x86: qemu: Add build options for SPLBin Meng2017-02-071-0/+9
| | | | | | | | | If SPL is used we want to use the generic SPL framework and boot from SPI via a board-specific means. Add these options to the board config file. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
View Lorry Controller Status