From 7bb0d212f29582b53160362e78ad7896c713811a Mon Sep 17 00:00:00 2001 From: Jun Nie Date: Sat, 27 Oct 2018 13:11:00 +0800 Subject: sunxi: add support for Banana Pi M2 Zero board Banana Pi M2 Zero is a board by Sinovoip with Allwinner H2+ SoC, 16-bit 512MiB DDR3 memory, a MicroSD slot, two MicroUSB ports (one OTG and one powering-only) and a miniHDMI port. Signed-off-by: Icenowy Zheng Signed-off-by: Jun Nie Acked-by: Maxime Ripard [jagan: Fixed board MAINTAINERS file] Signed-off-by: Jagan Teki --- arch/arm/dts/Makefile | 1 + arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 121 ++++++++++++++++++++++++ 2 files changed, 122 insertions(+) create mode 100644 arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts (limited to 'arch/arm/dts') diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index d36447d18d..3093c1185e 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -365,6 +365,7 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \ sun8i-a83t-cubietruck-plus.dtb \ sun8i-a83t-tbs-a711.dts dtb-$(CONFIG_MACH_SUN8I_H3) += \ + sun8i-h2-plus-bananapi-m2-zero.dtb \ sun8i-h2-plus-libretech-all-h3-cc.dtb \ sun8i-h2-plus-orangepi-r1.dtb \ sun8i-h2-plus-orangepi-zero.dtb \ diff --git a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts new file mode 100644 index 0000000000..7d01f93226 --- /dev/null +++ b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts @@ -0,0 +1,121 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2017 Icenowy Zheng + * + * Based on sun8i-h3-bananapi-m2-plus.dts, which is: + * Copyright (C) 2016 Chen-Yu Tsai + */ + +/dts-v1/; +#include "sun8i-h3.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include +#include + +/ { + model = "Banana Pi BPI-M2-Zero"; + compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + + pwr_led { + label = "bananapi-m2-zero:red:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ + default-state = "on"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + + sw4 { + label = "power"; + linux,code = ; + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + }; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ + }; +}; + +&ehci0 { + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + /* + * On the production batch of this board the card detect GPIO is + * high active (card inserted), although on the early samples it's + * low active. + */ + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + status = "okay"; +}; + +&mmc1 { + vmmc-supply = <®_vcc3v3>; + vqmmc-supply = <®_vcc3v3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&pio>; + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */ + interrupt-names = "host-wake"; + }; +}; + +&ohci0 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + /* + * There're two micro-USB connectors, one is power-only and another is + * OTG. The Vbus of these two connectors are connected together, so + * the external USB device will be powered just by the power input + * from the power-only USB port. + */ + status = "okay"; +}; -- cgit v1.2.1 From 1b39a1834ed182bbd8036a5cd74a9ea111fa4691 Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Mon, 29 Oct 2018 00:56:47 +0000 Subject: sunxi: A64: Update .dts/.dtsi files MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Update the .dts/.dtsi file from the Linux sunxi/dt64-for-4.20 tree: commit 679294497be31596e1c9c61507746d72b6b05f26 Author: Rodrigo Exterckötter Tjäder Date: Wed Sep 26 19:48:24 2018 +0000 arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay Signed-off-by: Andre Przywara Acked-by: Maxime Ripard Reviewed-by: Jagan Teki --- arch/arm/dts/sun50i-a64-amarula-relic.dts | 168 +++++++++++++- arch/arm/dts/sun50i-a64-bananapi-m64.dts | 34 ++- arch/arm/dts/sun50i-a64-nanopi-a64.dts | 89 +++++++- arch/arm/dts/sun50i-a64-olinuxino.dts | 103 ++++++++- arch/arm/dts/sun50i-a64-orangepi-win.dts | 179 ++++++++++++++- arch/arm/dts/sun50i-a64-pine64.dts | 32 ++- arch/arm/dts/sun50i-a64-sopine-baseboard.dts | 32 ++- arch/arm/dts/sun50i-a64-sopine.dtsi | 15 ++ arch/arm/dts/sun50i-a64.dtsi | 313 +++++++++++++++++++++++++-- 9 files changed, 920 insertions(+), 45 deletions(-) (limited to 'arch/arm/dts') diff --git a/arch/arm/dts/sun50i-a64-amarula-relic.dts b/arch/arm/dts/sun50i-a64-amarula-relic.dts index f3b4e93ece..6cb2b7f0c8 100644 --- a/arch/arm/dts/sun50i-a64-amarula-relic.dts +++ b/arch/arm/dts/sun50i-a64-amarula-relic.dts @@ -22,11 +22,11 @@ stdout-path = "serial0:115200n8"; }; - reg_vcc3v3: vcc3v3 { - compatible = "regulator-fixed"; - regulator-name = "vcc3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&rtc 1>; + clock-names = "ext_clock"; + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* WL-PMU-EN: PL2 */ }; }; @@ -34,10 +34,34 @@ status = "okay"; }; +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_dcdc1>; + /* + * Schematic shows both dldo4 and eldo1 connected for vcc-io-wifi, but + * dldo4 connection shows DNP(Do Not Populate) and eldo1 connected with + * 0Ohm register to vcc-io-wifi so eldo1 is used. + */ + vqmmc-supply = <®_eldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&r_pio>; + interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* WL-WAKE-AP: PL3 */ + interrupt-names = "host-wake"; + }; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins>; - vmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -48,9 +72,138 @@ status = "okay"; }; +&r_rsb { + status = "okay"; + + axp803: pmic@3a3 { + compatible = "x-powers,axp803"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ + }; +}; + +#include "axp803.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pll-avcc"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1040000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-cpux"; +}; + +/* DCDC3 is polyphased with DCDC2 */ + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-hdmi-dsi-sensor"; +}; + +®_dldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-mipi"; +}; + +®_dldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "dovdd-csi"; +}; + +®_dldo4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-io"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + +®_eldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "cpvdd"; +}; + +®_eldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-csi"; +}; + +®_fldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-1v2-hsic"; +}; + +/* + * The A64 chip cannot work without this regulator off, although + * it seems to be only driving the AR100 core. + * Maybe we don't still know well about CPUs domain. + */ +®_fldo2 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_pb_pins>; status = "okay"; }; @@ -61,5 +214,6 @@ &usbphy { usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + usb0_vbus-supply = <®_drivevbus>; status = "okay"; }; diff --git a/arch/arm/dts/sun50i-a64-bananapi-m64.dts b/arch/arm/dts/sun50i-a64-bananapi-m64.dts index 0716b14411..ef1c90401b 100644 --- a/arch/arm/dts/sun50i-a64-bananapi-m64.dts +++ b/arch/arm/dts/sun50i-a64-bananapi-m64.dts @@ -60,6 +60,17 @@ stdout-path = "serial0:115200n8"; }; + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; @@ -86,6 +97,10 @@ }; }; +&de { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -103,6 +118,17 @@ status = "okay"; }; +&hdmi { + hvcc-supply = <®_dldo1>; + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins>; @@ -151,7 +177,7 @@ &mmc2 { pinctrl-names = "default"; - pinctrl-0 = <&mmc2_pins>; + pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>; vmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; @@ -296,9 +322,13 @@ regulator-name = "vcc-rtc"; }; +&simplefb_hdmi { + vcc-hdmi-supply = <®_dldo1>; +}; + &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_pb_pins>; status = "okay"; }; diff --git a/arch/arm/dts/sun50i-a64-nanopi-a64.dts b/arch/arm/dts/sun50i-a64-nanopi-a64.dts index e2dce48fa2..31884dbc88 100644 --- a/arch/arm/dts/sun50i-a64-nanopi-a64.dts +++ b/arch/arm/dts/sun50i-a64-nanopi-a64.dts @@ -51,12 +51,44 @@ compatible = "friendlyarm,nanopi-a64", "allwinner,sun50i-a64"; aliases { + ethernet0 = &emac; serial0 = &uart0; }; chosen { stdout-path = "serial0:115200n8"; }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + blue { + label = "nanopi-a64:blue:status"; + gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */ + }; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&rtc 1>; + clock-names = "ext_clock"; + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + }; +}; + +&de { + status = "okay"; }; &ehci0 { @@ -67,6 +99,26 @@ status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_dcdc1>; + status = "okay"; +}; + +&hdmi { + hvcc-supply = <®_dldo1>; + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + /* i2c1 connected with gpio headers like pine64, bananapi */ &i2c1 { pinctrl-names = "default"; @@ -78,6 +130,13 @@ bias-pull-up; }; +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <7>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; @@ -88,6 +147,24 @@ status = "okay"; }; +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dldo4>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + rtl8189etv: wifi@1 { + reg = <1>; + interrupt-parent = <&r_pio>; + interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */ + interrupt-names = "host-wake"; + }; +}; + &ohci0 { status = "okay"; }; @@ -125,9 +202,9 @@ ®_dcdc1 { regulator-always-on; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-name = "vcc-3v"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; }; ®_dcdc2 { @@ -195,9 +272,13 @@ regulator-name = "vcc-rtc"; }; +&simplefb_hdmi { + vcc-hdmi-supply = <®_dldo1>; +}; + &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_pb_pins>; status = "okay"; }; diff --git a/arch/arm/dts/sun50i-a64-olinuxino.dts b/arch/arm/dts/sun50i-a64-olinuxino.dts index 3b3081b10e..f7a4bccaa5 100644 --- a/arch/arm/dts/sun50i-a64-olinuxino.dts +++ b/arch/arm/dts/sun50i-a64-olinuxino.dts @@ -51,6 +51,7 @@ compatible = "olimex,a64-olinuxino", "allwinner,sun50i-a64"; aliases { + ethernet0 = &emac; serial0 = &uart0; }; @@ -58,12 +59,74 @@ stdout-path = "serial0:115200n8"; }; + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + reg_usb1_vbus: usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 6 9 GPIO_ACTIVE_HIGH>; /* PG9 */ + status = "okay"; + }; + wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ }; }; +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_dcdc1>; + allwinner,tx-delay-ps = <600>; + status = "okay"; +}; + +&hdmi { + hvcc-supply = <®_dldo1>; + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; @@ -92,6 +155,14 @@ }; }; +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + &r_rsb { status = "okay"; @@ -100,6 +171,7 @@ reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ }; }; @@ -142,10 +214,14 @@ /* DCDC3 is polyphased with DCDC2 */ +/* + * The board uses DDR3L DRAM chips. 1.36V is the closest to the nominal + * 1.35V that the PMIC can drive. + */ ®_dcdc5 { regulator-always-on; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; + regulator-min-microvolt = <1360000>; + regulator-max-microvolt = <1360000>; regulator-name = "vcc-ddr3"; }; @@ -180,6 +256,11 @@ regulator-name = "vcc-wifi-io"; }; +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + ®_eldo1 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -214,8 +295,24 @@ regulator-name = "vcc-rtc"; }; +&simplefb_hdmi { + vcc-hdmi-supply = <®_dldo1>; +}; + &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { status = "okay"; + usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus-supply = <®_usb1_vbus>; }; diff --git a/arch/arm/dts/sun50i-a64-orangepi-win.dts b/arch/arm/dts/sun50i-a64-orangepi-win.dts index bf42690a33..b0c64f7579 100644 --- a/arch/arm/dts/sun50i-a64-orangepi-win.dts +++ b/arch/arm/dts/sun50i-a64-orangepi-win.dts @@ -1,5 +1,6 @@ /* * Copyright (C) 2017 Jagan Teki + * Copyright (C) 2017-2018 Samuel Holland * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual @@ -51,23 +52,127 @@ compatible = "xunlong,orangepi-win", "allwinner,sun50i-a64"; aliases { + ethernet0 = &emac; serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; }; chosen { stdout-path = "serial0:115200n8"; }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + status { + label = "orangepi:green:status"; + gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */ + }; + }; + + reg_gmac_3v3: gmac-3v3 { + compatible = "regulator-fixed"; + regulator-name = "gmac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 14 GPIO_ACTIVE_HIGH>; /* PD14 */ + status = "okay"; + }; + + reg_usb1_vbus: usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 7 GPIO_ACTIVE_HIGH>; /* PD7 */ + status = "okay"; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 */ + }; +}; + +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; }; &ehci1 { status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_gmac_3v3>; + status = "okay"; +}; + +&hdmi { + hvcc-supply = <®_dldo1>; + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + disable-wp; + bus-width = <4>; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_dldo2>; + vqmmc-supply = <®_dldo4>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&ohci0 { status = "okay"; }; @@ -89,9 +194,8 @@ #include "axp803.dtsi" ®_aldo1 { - regulator-always-on; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; regulator-name = "afvcc-csi"; }; @@ -163,12 +267,23 @@ regulator-name = "vcc-wifi-io"; }; +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + ®_eldo1 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-name = "cpvdd"; }; +®_eldo3 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-csi"; +}; + ®_fldo1 { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; @@ -191,13 +306,65 @@ regulator-name = "vcc-rtc"; }; +&simplefb_hdmi { + vcc-hdmi-supply = <®_dldo1>; +}; + +&spi0 { + status = "okay"; + + spi-flash@0 { + compatible = "mxicy,mx25l1606e", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + m25p,fast-read; + status = "okay"; + }; +}; + +/* On debug connector */ &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_pb_pins>; status = "okay"; }; -&usbphy { +/* Bluetooth */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + status = "okay"; +}; + +/* On Pi-2 connector, RTS/CTS optional */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "disabled"; +}; + +/* On Pi-2 connector, RTS/CTS optional */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "disabled"; +}; + +/* On Pi-2 connector (labeled for SPI1), RTS/CTS optional */ +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins>; + status = "disabled"; +}; + +&usb_otg { + dr_mode = "otg"; status = "okay"; }; +&usbphy { + usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; diff --git a/arch/arm/dts/sun50i-a64-pine64.dts b/arch/arm/dts/sun50i-a64-pine64.dts index a75825798a..c077b6c1f4 100644 --- a/arch/arm/dts/sun50i-a64-pine64.dts +++ b/arch/arm/dts/sun50i-a64-pine64.dts @@ -62,6 +62,21 @@ chosen { stdout-path = "serial0:115200n8"; }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; +}; + +&de { + status = "okay"; }; &ehci0 { @@ -82,6 +97,17 @@ }; +&hdmi { + hvcc-supply = <®_dldo1>; + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins>; @@ -229,6 +255,10 @@ regulator-name = "vcc-rtc"; }; +&simplefb_hdmi { + vcc-hdmi-supply = <®_dldo1>; +}; + /* On Euler connector */ &spdif { status = "disabled"; @@ -237,7 +267,7 @@ /* On Exp and Euler connectors */ &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_pb_pins>; status = "okay"; }; diff --git a/arch/arm/dts/sun50i-a64-sopine-baseboard.dts b/arch/arm/dts/sun50i-a64-sopine-baseboard.dts index abe179de35..53fcc9098d 100644 --- a/arch/arm/dts/sun50i-a64-sopine-baseboard.dts +++ b/arch/arm/dts/sun50i-a64-sopine-baseboard.dts @@ -61,6 +61,17 @@ stdout-path = "serial0:115200n8"; }; + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + reg_vcc1v8: vcc1v8 { compatible = "regulator-fixed"; regulator-name = "vcc1v8"; @@ -69,6 +80,10 @@ }; }; +&de { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -86,6 +101,17 @@ status = "okay"; }; +&hdmi { + hvcc-supply = <®_dldo1>; + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &mdio { ext_rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22"; @@ -134,9 +160,13 @@ regulator-name = "vcc-wifi"; }; +&simplefb_hdmi { + vcc-hdmi-supply = <®_dldo1>; +}; + &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_pb_pins>; status = "okay"; }; diff --git a/arch/arm/dts/sun50i-a64-sopine.dtsi b/arch/arm/dts/sun50i-a64-sopine.dtsi index 43418bd881..6723b8695e 100644 --- a/arch/arm/dts/sun50i-a64-sopine.dtsi +++ b/arch/arm/dts/sun50i-a64-sopine.dtsi @@ -45,6 +45,8 @@ #include "sun50i-a64.dtsi" +#include + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; @@ -52,6 +54,7 @@ non-removable; disable-wp; bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; @@ -66,6 +69,18 @@ }; }; +&spi0 { + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + }; +}; + #include "axp803.dtsi" ®_aldo2 { diff --git a/arch/arm/dts/sun50i-a64.dtsi b/arch/arm/dts/sun50i-a64.dtsi index 7a083637c4..f3a66f8882 100644 --- a/arch/arm/dts/sun50i-a64.dtsi +++ b/arch/arm/dts/sun50i-a64.dtsi @@ -43,9 +43,12 @@ */ #include +#include #include #include #include +#include +#include / { interrupt-parent = <&gic>; @@ -57,17 +60,21 @@ #size-cells = <1>; ranges; -/* - * The pipeline mixer0-lcd0 depends on clock CLK_MIXER0 from DE2 CCU. - * However there is no support for this clock on A64 yet, so we depend - * on the upstream clocks here to keep them (and thus CLK_MIXER0) up. - */ simplefb_lcd: framebuffer-lcd { compatible = "allwinner,simple-framebuffer", "simple-framebuffer"; allwinner,pipeline = "mixer0-lcd0"; clocks = <&ccu CLK_TCON0>, - <&ccu CLK_DE>, <&ccu CLK_BUS_DE>; + <&display_clocks CLK_MIXER0>; + status = "disabled"; + }; + + simplefb_hdmi: framebuffer-hdmi { + compatible = "allwinner,simple-framebuffer", + "simple-framebuffer"; + allwinner,pipeline = "mixer1-lcd1-hdmi"; + clocks = <&display_clocks CLK_MIXER1>, + <&ccu CLK_TCON1>, <&ccu CLK_HDMI>; status = "disabled"; }; }; @@ -81,6 +88,7 @@ device_type = "cpu"; reg = <0>; enable-method = "psci"; + next-level-cache = <&L2>; }; cpu1: cpu@1 { @@ -88,6 +96,7 @@ device_type = "cpu"; reg = <1>; enable-method = "psci"; + next-level-cache = <&L2>; }; cpu2: cpu@2 { @@ -95,6 +104,7 @@ device_type = "cpu"; reg = <2>; enable-method = "psci"; + next-level-cache = <&L2>; }; cpu3: cpu@3 { @@ -102,7 +112,20 @@ device_type = "cpu"; reg = <3>; enable-method = "psci"; + next-level-cache = <&L2>; }; + + L2: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + de: display-engine { + compatible = "allwinner,sun50i-a64-display-engine"; + allwinner,pipelines = <&mixer0>, + <&mixer1>; + status = "disabled"; }; osc24M: osc24M_clk { @@ -168,10 +191,92 @@ #size-cells = <1>; ranges; + de2@1000000 { + compatible = "allwinner,sun50i-a64-de2"; + reg = <0x1000000 0x400000>; + allwinner,sram = <&de2_sram 1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1000000 0x400000>; + + display_clocks: clock@0 { + compatible = "allwinner,sun50i-a64-de2-clk"; + reg = <0x0 0x100000>; + clocks = <&ccu CLK_DE>, + <&ccu CLK_BUS_DE>; + clock-names = "mod", + "bus"; + resets = <&ccu RST_BUS_DE>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + mixer0: mixer@100000 { + compatible = "allwinner,sun50i-a64-de2-mixer-0"; + reg = <0x100000 0x100000>; + clocks = <&display_clocks CLK_BUS_MIXER0>, + <&display_clocks CLK_MIXER0>; + clock-names = "bus", + "mod"; + resets = <&display_clocks RST_MIXER0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mixer0_out: port@1 { + reg = <1>; + + mixer0_out_tcon0: endpoint { + remote-endpoint = <&tcon0_in_mixer0>; + }; + }; + }; + }; + + mixer1: mixer@200000 { + compatible = "allwinner,sun50i-a64-de2-mixer-1"; + reg = <0x200000 0x100000>; + clocks = <&display_clocks CLK_BUS_MIXER1>, + <&display_clocks CLK_MIXER1>; + clock-names = "bus", + "mod"; + resets = <&display_clocks RST_MIXER1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mixer1_out: port@1 { + reg = <1>; + + mixer1_out_tcon1: endpoint { + remote-endpoint = <&tcon1_in_mixer1>; + }; + }; + }; + }; + }; + syscon: syscon@1c00000 { - compatible = "allwinner,sun50i-a64-system-controller", - "syscon"; + compatible = "allwinner,sun50i-a64-system-control"; reg = <0x01c00000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sram_c: sram@18000 { + compatible = "mmio-sram"; + reg = <0x00018000 0x28000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x00018000 0x28000>; + + de2_sram: sram-section@0 { + compatible = "allwinner,sun50i-a64-sram-c"; + reg = <0x0000 0x28000>; + }; + }; }; dma: dma-controller@1c02000 { @@ -185,6 +290,75 @@ #dma-cells = <1>; }; + tcon0: lcd-controller@1c0c000 { + compatible = "allwinner,sun50i-a64-tcon-lcd", + "allwinner,sun8i-a83t-tcon-lcd"; + reg = <0x01c0c000 0x1000>; + interrupts = ; + clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>; + clock-names = "ahb", "tcon-ch0"; + clock-output-names = "tcon-pixel-clock"; + resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>; + reset-names = "lcd", "lvds"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tcon0_in_mixer0: endpoint@0 { + reg = <0>; + remote-endpoint = <&mixer0_out_tcon0>; + }; + }; + + tcon0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + }; + }; + + tcon1: lcd-controller@1c0d000 { + compatible = "allwinner,sun50i-a64-tcon-tv", + "allwinner,sun8i-a83t-tcon-tv"; + reg = <0x01c0d000 0x1000>; + interrupts = ; + clocks = <&ccu CLK_BUS_TCON1>, <&ccu CLK_TCON1>; + clock-names = "ahb", "tcon-ch1"; + resets = <&ccu RST_BUS_TCON1>; + reset-names = "lcd"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon1_in: port@0 { + reg = <0>; + + tcon1_in_mixer1: endpoint { + remote-endpoint = <&mixer1_out_tcon1>; + }; + }; + + tcon1_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + tcon1_out_hdmi: endpoint@1 { + reg = <1>; + remote-endpoint = <&hdmi_in_tcon1>; + }; + }; + }; + }; + mmc0: mmc@1c0f000 { compatible = "allwinner,sun50i-a64-mmc"; reg = <0x01c0f000 0x1000>; @@ -227,6 +401,11 @@ #size-cells = <0>; }; + sid: eeprom@1c14000 { + compatible = "allwinner,sun50i-a64-sid"; + reg = <0x1c14000 0x400>; + }; + usb_otg: usb@1c19000 { compatible = "allwinner,sun8i-a33-musb"; reg = <0x01c19000 0x0400>; @@ -356,7 +535,7 @@ }; mmc2_pins: mmc2-pins { - pins = "PC1", "PC5", "PC6", "PC8", "PC9", + pins = "PC5", "PC6", "PC8", "PC9", "PC10","PC11", "PC12", "PC13", "PC14", "PC15", "PC16"; function = "mmc2"; @@ -364,6 +543,18 @@ bias-pull-up; }; + mmc2_ds_pin: mmc2-ds-pin { + pins = "PC1"; + function = "mmc2"; + drive-strength = <30>; + bias-pull-up; + }; + + pwm_pin: pwm_pin { + pins = "PD22"; + function = "pwm"; + }; + rmii_pins: rmii_pins { pins = "PD10", "PD11", "PD13", "PD14", "PD17", "PD18", "PD19", "PD20", "PD22", "PD23"; @@ -394,7 +585,7 @@ function = "spi1"; }; - uart0_pins_a: uart0 { + uart0_pb_pins: uart0-pb-pins { pins = "PB8", "PB9"; function = "uart0"; }; @@ -474,15 +665,6 @@ status = "disabled"; }; - pwm: pwm@1c21400 { - compatible = "allwinner,sun50i-a64-pwm", - "allwinner,sun5i-a13-pwm"; - reg = <0x01c21400 0x8>; - clocks = <&osc24M>; - #pwm-cells = <3>; - status = "disabled"; - }; - uart0: serial@1c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; @@ -617,8 +799,6 @@ clocks = <&ccu CLK_BUS_EMAC>; clock-names = "stmmaceth"; status = "disabled"; - #address-cells = <1>; - #size-cells = <0>; mdio: mdio { compatible = "snps,dwmac-mdio"; @@ -638,11 +818,69 @@ #interrupt-cells = <3>; }; + pwm: pwm@1c21400 { + compatible = "allwinner,sun50i-a64-pwm", + "allwinner,sun5i-a13-pwm"; + reg = <0x01c21400 0x400>; + clocks = <&osc24M>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pin>; + #pwm-cells = <3>; + status = "disabled"; + }; + + hdmi: hdmi@1ee0000 { + compatible = "allwinner,sun50i-a64-dw-hdmi", + "allwinner,sun8i-a83t-dw-hdmi"; + reg = <0x01ee0000 0x10000>; + reg-io-width = <1>; + interrupts = ; + clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>, + <&ccu CLK_HDMI>; + clock-names = "iahb", "isfr", "tmds"; + resets = <&ccu RST_BUS_HDMI1>; + reset-names = "ctrl"; + phys = <&hdmi_phy>; + phy-names = "hdmi-phy"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + hdmi_in: port@0 { + reg = <0>; + + hdmi_in_tcon1: endpoint { + remote-endpoint = <&tcon1_out_hdmi>; + }; + }; + + hdmi_out: port@1 { + reg = <1>; + }; + }; + }; + + hdmi_phy: hdmi-phy@1ef0000 { + compatible = "allwinner,sun50i-a64-hdmi-phy"; + reg = <0x01ef0000 0x10000>; + clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>, + <&ccu 7>; + clock-names = "bus", "mod", "pll-0"; + resets = <&ccu RST_BUS_HDMI0>; + reset-names = "phy"; + #phy-cells = <0>; + }; + rtc: rtc@1f00000 { compatible = "allwinner,sun6i-a31-rtc"; reg = <0x01f00000 0x54>; interrupts = , ; + clock-output-names = "rtc-osc32k", "rtc-osc32k-out"; + clocks = <&osc32k>; + #clock-cells = <1>; }; r_intc: interrupt-controller@1f00c00 { @@ -664,6 +902,29 @@ #reset-cells = <1>; }; + r_i2c: i2c@1f02400 { + compatible = "allwinner,sun50i-a64-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x01f02400 0x400>; + interrupts = ; + clocks = <&r_ccu CLK_APB0_I2C>; + resets = <&r_ccu RST_APB0_I2C>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + r_pwm: pwm@1f03800 { + compatible = "allwinner,sun50i-a64-pwm", + "allwinner,sun5i-a13-pwm"; + reg = <0x01f03800 0x400>; + clocks = <&osc24M>; + pinctrl-names = "default"; + pinctrl-0 = <&r_pwm_pin>; + #pwm-cells = <3>; + status = "disabled"; + }; + r_pio: pinctrl@1f02c00 { compatible = "allwinner,sun50i-a64-r-pinctrl"; reg = <0x01f02c00 0x400>; @@ -675,6 +936,16 @@ interrupt-controller; #interrupt-cells = <3>; + r_i2c_pl89_pins: r-i2c-pl89-pins { + pins = "PL8", "PL9"; + function = "s_i2c"; + }; + + r_pwm_pin: pwm { + pins = "PL10"; + function = "s_pwm"; + }; + r_rsb_pins: rsb { pins = "PL0", "PL1"; function = "s_rsb"; -- cgit v1.2.1 From ababb5920e8992c9bb7956df3cc85dc68d27dfe8 Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Mon, 29 Oct 2018 00:56:48 +0000 Subject: sunxi: A64: Re-add syscon to DT node The sun50i-a64.dtsi changes introduced in Linux v4.19-rc1 changed the compatible name for the syscon controller, dropping the generic "syscon" fallback. Using this new DT node will make the Ethernet driver in every older kernel (or non-Linux kernels) fail to initialise the MAC device. To allow booting distribution kernels (from installer images via UEFI, for instance), re-add the syscon compatible string as a fallback. This works with both older and newer kernels. Signed-off-by: Andre Przywara Acked-by: Maxime Ripard Reviewed-by: Jagan Teki --- arch/arm/dts/sun50i-a64.dtsi | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch/arm/dts') diff --git a/arch/arm/dts/sun50i-a64.dtsi b/arch/arm/dts/sun50i-a64.dtsi index f3a66f8882..ff41abc96a 100644 --- a/arch/arm/dts/sun50i-a64.dtsi +++ b/arch/arm/dts/sun50i-a64.dtsi @@ -259,7 +259,8 @@ }; syscon: syscon@1c00000 { - compatible = "allwinner,sun50i-a64-system-control"; + compatible = "allwinner,sun50i-a64-system-control", + "syscon"; reg = <0x01c00000 0x1000>; #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.1 From 4c974eefbff91e052a48663e7da9f15b1b70286e Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Mon, 29 Oct 2018 00:56:49 +0000 Subject: sunxi: H3/H5: Update .dts files MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Update the .dts/.dtsi files from the Linux sunxi/dt64-for-4.20 tree: commit 679294497be31596e1c9c61507746d72b6b05f26 Author: Rodrigo Exterckötter Tjäder Date: Wed Sep 26 19:48:24 2018 +0000 arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay Signed-off-by: Andre Przywara Acked-by: Maxime Ripard Reviewed-by: Jagan Teki --- arch/arm/dts/sun50i-h5-orangepi-pc2.dts | 12 +++++++++++ arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts | 2 -- arch/arm/dts/sun8i-h3.dtsi | 31 +++++++++++++++++++++++++++ arch/arm/dts/sunxi-h3-h5.dtsi | 2 -- 4 files changed, 43 insertions(+), 4 deletions(-) (limited to 'arch/arm/dts') diff --git a/arch/arm/dts/sun50i-h5-orangepi-pc2.dts b/arch/arm/dts/sun50i-h5-orangepi-pc2.dts index 98862c7c72..3e0d5a9c09 100644 --- a/arch/arm/dts/sun50i-h5-orangepi-pc2.dts +++ b/arch/arm/dts/sun50i-h5-orangepi-pc2.dts @@ -207,6 +207,18 @@ status = "okay"; }; +&spi0 { + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; diff --git a/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts b/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts index e79cf3baf4..1238de25a9 100644 --- a/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts +++ b/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts @@ -105,7 +105,6 @@ }; }; -/* &spi0 { status = "okay"; @@ -117,7 +116,6 @@ spi-max-frequency = <40000000>; }; }; -*/ &ohci0 { status = "okay"; diff --git a/arch/arm/dts/sun8i-h3.dtsi b/arch/arm/dts/sun8i-h3.dtsi index 41d57c76f2..f0096074a4 100644 --- a/arch/arm/dts/sun8i-h3.dtsi +++ b/arch/arm/dts/sun8i-h3.dtsi @@ -84,21 +84,30 @@ compatible = "arm,cortex-a7"; device_type = "cpu"; reg = <1>; + clocks = <&ccu CLK_CPUX>; + clock-names = "cpu"; operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; }; cpu@2 { compatible = "arm,cortex-a7"; device_type = "cpu"; reg = <2>; + clocks = <&ccu CLK_CPUX>; + clock-names = "cpu"; operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; }; cpu@3 { compatible = "arm,cortex-a7"; device_type = "cpu"; reg = <3>; + clocks = <&ccu CLK_CPUX>; + clock-names = "cpu"; operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; }; }; @@ -111,6 +120,28 @@ }; soc { + system-control@1c00000 { + compatible = "allwinner,sun8i-h3-system-control"; + reg = <0x01c00000 0x30>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sram_c: sram@1d00000 { + compatible = "mmio-sram"; + reg = <0x01d00000 0x80000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x01d00000 0x80000>; + + ve_sram: sram-section@0 { + compatible = "allwinner,sun8i-h3-sram-c1", + "allwinner,sun4i-a10-sram-c1"; + reg = <0x000000 0x80000>; + }; + }; + }; + mali: gpu@1c40000 { compatible = "allwinner,sun8i-h3-mali", "arm,mali-400"; reg = <0x01c40000 0x10000>; diff --git a/arch/arm/dts/sunxi-h3-h5.dtsi b/arch/arm/dts/sunxi-h3-h5.dtsi index c3bff1105e..fc6131315c 100644 --- a/arch/arm/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/dts/sunxi-h3-h5.dtsi @@ -506,8 +506,6 @@ reset-names = "stmmaceth"; clocks = <&ccu CLK_BUS_EMAC>; clock-names = "stmmaceth"; - #address-cells = <1>; - #size-cells = <0>; status = "disabled"; mdio: mdio { -- cgit v1.2.1 From 4f9d34e633c498b9f706a78f465d337c041f4a65 Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Mon, 29 Oct 2018 00:56:50 +0000 Subject: sunxi: A64: Add Pine64-LTS board The Pine64 LTS is an updated version of the Pine64, copying the technical updates from the SoPine platform: LPDDR3 DRAM, eMMC socket and soldered SPI flash chip, even the broken SD card detect pin has been copied. Consequently this leads to the .dts (copied from the kernel) just including the SoPine baseboard .dts, and the defconfig being almost identical. Nevertheless the boards deserves a separate config. Signed-off-by: Andre Przywara Acked-by: Maxime Ripard Reviewed-by: Jagan Teki --- arch/arm/dts/sun50i-a64-pine64-lts.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+) create mode 100644 arch/arm/dts/sun50i-a64-pine64-lts.dts (limited to 'arch/arm/dts') diff --git a/arch/arm/dts/sun50i-a64-pine64-lts.dts b/arch/arm/dts/sun50i-a64-pine64-lts.dts new file mode 100644 index 0000000000..72d6961dc3 --- /dev/null +++ b/arch/arm/dts/sun50i-a64-pine64-lts.dts @@ -0,0 +1,13 @@ +/* + * SPDX-License-Identifier: (GPL-2.0+ OR MIT) + * + * Copyright (c) 2018 ARM Ltd. + */ + +#include "sun50i-a64-sopine-baseboard.dts" + +/ { + model = "Pine64 LTS"; + compatible = "pine64,pine64-lts", "allwinner,sun50i-r18", + "allwinner,sun50i-a64"; +}; -- cgit v1.2.1 From b972831c3cd24f3c9bb0995ed61db8f8239f3391 Mon Sep 17 00:00:00 2001 From: Vasily Khoruzhick Date: Mon, 5 Nov 2018 20:24:31 -0800 Subject: sunxi: DT: add support for Pinebook Pinebook is a laptop produced by Pine64, with USB-connected keyboard, USB-connected touchpad and an eDP LCD panel connected via a RGB-eDP bridge from Analogix. Signed-off-by: Vasily Khoruzhick Acked-by: Maxime Ripard Tested-by: Maxime Ripard Cc: Vagrant Cascadian Reviewed-by: Jagan Teki --- arch/arm/dts/Makefile | 1 + arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi | 15 ++ arch/arm/dts/sun50i-a64-pinebook.dts | 294 +++++++++++++++++++++++++++ 3 files changed, 310 insertions(+) create mode 100644 arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi create mode 100644 arch/arm/dts/sun50i-a64-pinebook.dts (limited to 'arch/arm/dts') diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 3093c1185e..eae6b9ee5d 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -406,6 +406,7 @@ dtb-$(CONFIG_MACH_SUN50I) += \ sun50i-a64-orangepi-win.dtb \ sun50i-a64-pine64-plus.dtb \ sun50i-a64-pine64.dtb \ + sun50i-a64-pinebook.dtb \ sun50i-a64-sopine-baseboard.dtb dtb-$(CONFIG_MACH_SUN9I) += \ sun9i-a80-optimus.dtb \ diff --git a/arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi b/arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi new file mode 100644 index 0000000000..a99b7171d0 --- /dev/null +++ b/arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2018 Vasily Khoruzhick + * + */ + +/* The ANX6345 eDP-bridge is on r_i2c */ +&r_i2c { + anx6345: edp-bridge@38 { + compatible = "analogix,anx6345"; + reg = <0x38>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */ + status = "okay"; + }; +}; diff --git a/arch/arm/dts/sun50i-a64-pinebook.dts b/arch/arm/dts/sun50i-a64-pinebook.dts new file mode 100644 index 0000000000..ec537c5297 --- /dev/null +++ b/arch/arm/dts/sun50i-a64-pinebook.dts @@ -0,0 +1,294 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2017 Icenowy Zheng + * Copyright (C) 2018 Vasily Khoruzhick + * + */ + +/dts-v1/; + +#include "sun50i-a64.dtsi" + +#include +#include +#include + +/ { + model = "Pinebook"; + compatible = "pine64,pinebook", "allwinner,sun50i-a64"; + + aliases { + serial0 = &uart0; + ethernet0 = &rtl8723cs; + }; + + vdd_bl: regulator@0 { + compatible = "regulator-fixed"; + regulator-name = "bl-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ + enable-active-high; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 0>; + brightness-levels = <0 5 10 15 20 30 40 55 70 85 100>; + default-brightness-level = <2>; + enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */ + power-supply = <&vdd_bl>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + + framebuffer-lcd { + panel-supply = <®_dc1sw>; + dvdd25-supply = <®_dldo2>; + dvdd12-supply = <®_fldo1>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + lid_switch { + label = "Lid Switch"; + gpios = <&r_pio 0 12 GPIO_ACTIVE_LOW>; /* PL12 */ + linux,input-type = ; + linux,code = ; + linux,can-disable; + wakeup-source; + }; + }; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + }; +}; + +&ehci0 { + phys = <&usbphy 0>; + phy-names = "usb"; + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_dcdc1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + disable-wp; + bus-width = <4>; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_dldo4>; + vqmmc-supply = <®_eldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + rtl8723cs: wifi@1 { + reg = <1>; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_eldo1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + mmc-hs200-1_8v; + status = "okay"; +}; + +&ohci0 { + phys = <&usbphy 0>; + phy-names = "usb"; + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pwm { + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp803: pmic@3a3 { + compatible = "x-powers,axp803"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +/* The ANX6345 eDP-bridge is on r_i2c */ +&r_i2c { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&r_i2c_pl89_pins>; + status = "okay"; +}; + +#include "axp803.dtsi" + +®_aldo1 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vcc-csi"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pll-avcc"; +}; + +®_dc1sw { + regulator-name = "vcc-lcd"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-cpux"; +}; + +/* DCDC3 is polyphased with DCDC2 */ + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-hdmi"; +}; + +®_dldo2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-edp"; +}; + +®_dldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avdd-csi"; +}; + +®_dldo4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_eldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "cpvdd"; +}; + +®_eldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vdd-1v8-csi"; +}; + +®_fldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-1v2-hsic"; +}; + +®_fldo2 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_ldo_io0 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-usb"; + status = "okay"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +&simplefb_hdmi { + vcc-hdmi-supply = <®_dldo1>; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "host"; +}; + +&usbphy { + usb0_vbus-supply = <®_ldo_io0>; + usb1_vbus-supply = <®_ldo_io0>; + status = "okay"; +}; -- cgit v1.2.1 From d45a07aacaed6e1134b88843375a2fd7e1c7f28f Mon Sep 17 00:00:00 2001 From: Jagan Teki Date: Mon, 5 Nov 2018 13:20:39 +0530 Subject: arm64: allwinner: h6: Add common orangepi nodes into dtsi Based on the information from hardware schematics and orangepi vendor orangepi H6 boards, One Plus and Lite2 shares common nodes like axp805, uart, mmc0 etc. The common differences between them is - One Plus, has Ethernet - Lite2, has Wifi, USB3, CSI port. So, add common orangepi nodes into sun50i-h6-orangepi.dtsi so-that it case use on respective orangepi h6 board dts files. Cc: zhaoyifan Signed-off-by: Jagan Teki Acked-by: Maxime Ripard --- arch/arm/dts/sun50i-h6-orangepi-one-plus.dts | 140 +------------------------ arch/arm/dts/sun50i-h6-orangepi.dtsi | 150 +++++++++++++++++++++++++++ 2 files changed, 151 insertions(+), 139 deletions(-) create mode 100644 arch/arm/dts/sun50i-h6-orangepi.dtsi (limited to 'arch/arm/dts') diff --git a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts index 0612c19cd9..12e17567ab 100644 --- a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts +++ b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts @@ -4,147 +4,9 @@ * Author: Jagan Teki */ -/dts-v1/; - -#include "sun50i-h6.dtsi" - -#include +#include "sun50i-h6-orangepi.dtsi" / { model = "OrangePi One Plus"; compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6"; - - aliases { - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; -}; - -&mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>; - vmmc-supply = <®_cldo1>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; - bus-width = <4>; - status = "okay"; -}; - -&r_i2c { - status = "okay"; - - axp805: pmic@36 { - compatible = "x-powers,axp805", "x-powers,axp806"; - reg = <0x36>; - interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <1>; - x-powers,self-working-mode; - - regulators { - reg_aldo1: aldo1 { - regulator-always-on; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc-pl"; - }; - - reg_aldo2: aldo2 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc-ac200"; - }; - - reg_aldo3: aldo3 { - regulator-always-on; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc25-dram"; - }; - - reg_bldo1: bldo1 { - regulator-always-on; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-name = "vcc-bias-pll"; - }; - - reg_bldo2: bldo2 { - regulator-always-on; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-name = "vcc-efuse-pcie-hdmi-io"; - }; - - reg_bldo3: bldo3 { - regulator-always-on; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-name = "vcc-dcxoio"; - }; - - bldo4 { - /* unused */ - }; - - reg_cldo1: cldo1 { - regulator-always-on; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc-3v3"; - }; - - reg_cldo2: cldo2 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc-wifi-1"; - }; - - reg_cldo3: cldo3 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc-wifi-2"; - }; - - reg_dcdca: dcdca { - regulator-always-on; - regulator-min-microvolt = <810000>; - regulator-max-microvolt = <1080000>; - regulator-name = "vdd-cpu"; - }; - - reg_dcdcc: dcdcc { - regulator-min-microvolt = <810000>; - regulator-max-microvolt = <1080000>; - regulator-name = "vdd-gpu"; - }; - - reg_dcdcd: dcdcd { - regulator-always-on; - regulator-min-microvolt = <960000>; - regulator-max-microvolt = <960000>; - regulator-name = "vdd-sys"; - }; - - reg_dcdce: dcdce { - regulator-always-on; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-name = "vcc-dram"; - }; - - sw { - /* unused */ - }; - }; - }; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_ph_pins>; - status = "okay"; }; diff --git a/arch/arm/dts/sun50i-h6-orangepi.dtsi b/arch/arm/dts/sun50i-h6-orangepi.dtsi new file mode 100644 index 0000000000..0612c19cd9 --- /dev/null +++ b/arch/arm/dts/sun50i-h6-orangepi.dtsi @@ -0,0 +1,150 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2018 Amarula Solutions + * Author: Jagan Teki + */ + +/dts-v1/; + +#include "sun50i-h6.dtsi" + +#include + +/ { + model = "OrangePi One Plus"; + compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_cldo1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + bus-width = <4>; + status = "okay"; +}; + +&r_i2c { + status = "okay"; + + axp805: pmic@36 { + compatible = "x-powers,axp805", "x-powers,axp806"; + reg = <0x36>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + x-powers,self-working-mode; + + regulators { + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl"; + }; + + reg_aldo2: aldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-ac200"; + }; + + reg_aldo3: aldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc25-dram"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-bias-pll"; + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-efuse-pcie-hdmi-io"; + }; + + reg_bldo3: bldo3 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-dcxoio"; + }; + + bldo4 { + /* unused */ + }; + + reg_cldo1: cldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; + }; + + reg_cldo2: cldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-1"; + }; + + reg_cldo3: cldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-2"; + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdcc: dcdcc { + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-gpu"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <960000>; + regulator-max-microvolt = <960000>; + regulator-name = "vdd-sys"; + }; + + reg_dcdce: dcdce { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; + }; + + sw { + /* unused */ + }; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +}; -- cgit v1.2.1 From e6b16e785234873f86b0560b5387381ae9d72762 Mon Sep 17 00:00:00 2001 From: Jagan Teki Date: Mon, 5 Nov 2018 13:20:40 +0530 Subject: board: allwinner: sun50i-h6: Add Orangepi Lite2 support OrangePi Lite2 is Allwinner H6 based open-source SBC, which support: - Allwinner H6 Quad-core 64-bit ARM Cortex-A53 - GPU Mali-T720 - 1GB LPDDR3 RAM - AXP805 PMIC - AP6356S Wifi/BT - USB 2.0, USB 3.0 Host, OTG - HDMI port - 5V/2A DC power supply Signed-off-by: Jagan Teki Acked-by: Maxime Ripard --- arch/arm/dts/Makefile | 1 + arch/arm/dts/sun50i-h6-orangepi-lite2.dts | 11 +++++++++++ 2 files changed, 12 insertions(+) create mode 100644 arch/arm/dts/sun50i-h6-orangepi-lite2.dts (limited to 'arch/arm/dts') diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index eae6b9ee5d..1cbb45d679 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -396,6 +396,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \ sun50i-h5-orangepi-prime.dtb \ sun50i-h5-orangepi-zero-plus2.dtb dtb-$(CONFIG_MACH_SUN50I_H6) += \ + sun50i-h6-orangepi-lite2.dtb \ sun50i-h6-orangepi-one-plus.dtb \ sun50i-h6-pine-h64.dtb dtb-$(CONFIG_MACH_SUN50I) += \ diff --git a/arch/arm/dts/sun50i-h6-orangepi-lite2.dts b/arch/arm/dts/sun50i-h6-orangepi-lite2.dts new file mode 100644 index 0000000000..e098a2475f --- /dev/null +++ b/arch/arm/dts/sun50i-h6-orangepi-lite2.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2018 Jagan Teki + */ + +#include "sun50i-h6-orangepi.dtsi" + +/ { + model = "OrangePi Lite2"; + compatible = "xunlong,orangepi-lite2", "allwinner,sun50i-h6"; +}; -- cgit v1.2.1