feat(stm32mp15-fdts): add support for prtt1x board family

Add one device tree to support a family of boards (PRTT1C, PRTT1S,
PRTT1A) based on STM32MP151AAD3, used as sensors and actuators for
industrial, 10BaseT1L based networks.

This change was tested with barebox 2022.12.0 bootloader and kernel
v6.2.0-rc1.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Change-Id: Ibab9933eadd7aa379ae0a7c7ccbfc2fbb9a44ca8

1 files changed, 235 insertions, 0 deletions

diff --git a/fdts/stm32mp151a-prtt1a.dts b/fdts/stm32mp151a-prtt1a.dts
new file mode 100644
index 000000000..be9bdae7c
--- /dev/null
+++ b/fdts/stm32mp151a-prtt1a.dts
@@ -0,0 +1,235 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2023, Protonic Holland - All Rights Reserved
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxad-pinctrl.dtsi"
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp15-ddr3-1x2Gb-1066-binG.dtsi"
+
+/ {
+	model = "Protonic PRTT1A";
+	compatible = "prt,prtt1a", "st,stm32mp151";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		serial0 = &uart4;
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x10000000>;
+	};
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+	secure-status = "okay";
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <104000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&qspi_bk1_pins_a {
+	pins1 {
+		bias-pull-up;
+		drive-push-pull;
+		slew-rate = <1>;
+	};
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSI
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_DISABLED
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSI
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4R
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSI
+	>;
+
+	/* VCO = 1300.0 MHz => P = 650 (CPU) */
+	pll1: st,pll@0 {
+		compatible = "st,stm32mp1-pll";
+		reg = <0>;
+		cfg = <2 80 0 0 0 PQR(1,0,0)>;
+		frac = <0x800>;
+	};
+
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll@1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
+		cfg = <2 65 1 0 0 PQR(1,1,1)>;
+		frac = <0x1400>;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll@2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
+		cfg = <1 33 1 16 36 PQR(1,1,1)>;
+		frac = <0x1a04>;
+	};
+
+	/* VCO = 480.0 MHz => P = 120, Q = 40, R = 96 */
+	pll4: st,pll@3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
+		cfg = <1 39 3 11 4 PQR(1,1,1)>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&sdmmc1_b4_pins_a {
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+/* NOTE: Although the PRTT1A does not have an eMMC, we declare it
+ * anyway, in order to be able to use the same binary for the
+ * PRTT1C also. All involved pins are N.C. on PRTT1A/S for that
+ * reason, so it should do no harm. All inputs configured with
+ * pull-ups to avoid floating inputs. */
+&sdmmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&sdmmc2_b4_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+			 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+			 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+			 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+			 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
+
+&uart4_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 9, AF8)>; /* UART4_TX */
+		bias-disable;
+		drive-push-pull;
+		slew-rate = <0>;
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+		bias-pull-up;
+	};
+};