diff options
Diffstat (limited to 'baseboard/brya/baseboard.h')
| -rw-r--r-- | baseboard/brya/baseboard.h | 259 |
1 files changed, 0 insertions, 259 deletions
diff --git a/baseboard/brya/baseboard.h b/baseboard/brya/baseboard.h deleted file mode 100644 index 757b504d16..0000000000 --- a/baseboard/brya/baseboard.h +++ /dev/null @@ -1,259 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Brya baseboard configuration */ - -#ifndef __CROS_EC_BASEBOARD_H -#define __CROS_EC_BASEBOARD_H - -/* - * By default, enable all console messages excepted HC, ACPI and event: - * The sensor stack is generating a lot of activity. - */ -#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC))) -#undef CONFIG_HOSTCMD_DEBUG_MODE -#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF - -/* NPCX9 config */ -#define NPCX9_PWM1_SEL 1 /* GPIO C2 is used as PWM1. */ -/* - * This defines which pads (GPIO10/11 or GPIO64/65) are connected to - * the "UART1" (NPCX_UART_PORT0) controller when used for - * CONSOLE_UART. - */ -#define NPCX_UART_MODULE2 1 /* 1:GPIO64/65 for UART1 */ - -/* EC Defines */ -#define CONFIG_LTO -#define CONFIG_CBI_EEPROM -#define CONFIG_BOARD_VERSION_CBI -#define CONFIG_CRC8 -#define CONFIG_DPTF -#define CONFIG_FPU - -/* Verified boot configs */ -#define CONFIG_VBOOT_EFS2 -#define CONFIG_VBOOT_HASH -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 - -#define CONFIG_HIBERNATE_PSL - -/* Work around double CR50 reset by waiting in initial power on. */ -#define CONFIG_BOARD_RESET_AFTER_POWER_ON - -/* Host communication */ -#define CONFIG_HOSTCMD_ESPI -#define CONFIG_HOSTCMD_ESPI_VW_SLP_S4 - -/* - * TODO(b/179648721): implement sensors - */ -#define CONFIG_TABLET_MODE -#define CONFIG_TABLET_MODE_SWITCH -#define CONFIG_GMR_TABLET_MODE - -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_USE_HOST_EVENT -#define CONFIG_MKBP_INPUT_DEVICES - -/* LED */ -#define CONFIG_LED_COMMON - -/* Common charger defines */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGER -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 512 - -#define CONFIG_CMD_CHARGER_DUMP - -#define CONFIG_USB_CHARGER -#define CONFIG_BC12_DETECT_PI3USB9201 - -/* - * Don't allow the system to boot to S0 when the battery is low and unable to - * communicate on locked systems (which haven't PD negotiated) - */ -#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON_WITH_BATT 15000 -#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 15001 - -/* Common battery defines */ -#define CONFIG_BATTERY_SMART -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_PRESENT_CUSTOM -#define CONFIG_BATTERY_HW_PRESENT_CUSTOM -#define CONFIG_BATTERY_REVIVE_DISCONNECT -#define CONFIG_CMD_BATT_MFG_ACCESS -/* - * Enable support for battery hostcmd, supporting longer strings. - * support for EC_CMD_BATTERY_GET_STATIC version 1. - */ -#define CONFIG_BATTERY_V2 -#define CONFIG_BATTERY_COUNT 1 -#define CONFIG_HOSTCMD_BATTERY_V2 - -/* Chipset config */ -#define CONFIG_CHIPSET_ALDERLAKE_SLG4BD44540 - -#define CONFIG_CHIPSET_RESET_HOOK -#define CONFIG_CPU_PROCHOT_ACTIVE_LOW -#define CONFIG_EXTPOWER_GPIO -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_POWER_S0IX -#define CONFIG_POWER_SLEEP_FAILURE_DETECTION -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE -#define CONFIG_LOW_POWER_IDLE - -#define CONFIG_HOSTCMD_ESPI_RESET_SLP_SX_VW_ON_ESPI_RST - -/* - * TODO(b/191742284): When DAM enabled coreboot image is flashed on top of DAM - * disabled coreboot, S5 exit is taking more than 4 seconds, then EC triggers - * system shutdown. This WA deselects CONFIG_BOARD_HAS_RTC_RESET to prevent - * EC from system shutdown. - */ -/* #define CONFIG_BOARD_HAS_RTC_RESET */ - -#define CONFIG_CMD_AP_RESET_LOG -#define CONFIG_HOSTCMD_AP_RESET - -/* Buttons / Switches */ -#define CONFIG_VOLUME_BUTTONS -#define CONFIG_SWITCH - -/* Common Keyboard Defines */ -#define CONFIG_CMD_KEYBOARD - -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_KEYPAD -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#ifdef CONFIG_KEYBOARD_VIVALDI -#define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2 -#else -#define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI3 -#endif - -/* Thermal features */ -#define CONFIG_THROTTLE_AP -#define CONFIG_CHIPSET_CAN_THROTTLE - -#define CONFIG_PWM - -/* Enable I2C Support */ -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER - -/* EDP back-light control defines */ -#define CONFIG_BACKLIGHT_LID - -/* UART COMMAND */ -#define CONFIG_CMD_CHARGEN - -/* USB Type C and USB PD defines */ -/* Enable the new USB-C PD stack */ -#define CONFIG_USB_PD_TCPMV2 -#define CONFIG_USB_DRP_ACC_TRYSRC -#define CONFIG_USB_PD_REV30 - -#define CONFIG_CMD_HCDEBUG -#define CONFIG_CMD_PPC_DUMP -#define CONFIG_CMD_TCPC_DUMP - -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_ALT_MODE_UFP -#define CONFIG_USB_PD_DISCHARGE_PPC -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TCPM_NCT38XX - -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_HOSTCMD_PD_CONTROL /* Needed for TCPC FW update */ -#define CONFIG_CMD_USB_PD_PE - -/* - * The PS8815 TCPC was found to require a 50ms delay to consistently work - * with non-PD chargers. Override the default low-power mode exit delay. - */ -#undef CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE -#define CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE (50*MSEC) - -/* Enable USB3.2 DRD */ -#define CONFIG_USB_PD_USB32_DRD - -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_PD_VBUS_DETECT_TCPC - -#define CONFIG_USBC_PPC -/* Note - SN5S330 support automatically adds - * CONFIG_USBC_PPC_POLARITY - * CONFIG_USBC_PPC_SBU - * CONFIG_USBC_PPC_VCONN - */ -#define CONFIG_USBC_PPC_DEDICATED_INT - -#define CONFIG_USBC_SS_MUX -#define CONFIG_USB_MUX_VIRTUAL - -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP - -/* Enabling SOP* communication */ -#define CONFIG_CMD_USB_PD_CABLE -#define CONFIG_USB_PD_DECODE_SOP - -/* - * USB ID - * This is allocated specifically for Brya - * http://google3/hardware/standards/usb/ - */ -#define CONFIG_USB_PID 0x504F -/* Device version of product. */ -#define CONFIG_USB_BCD_DEV 0x0000 - -#ifndef __ASSEMBLER__ - -#include <stdbool.h> -#include <stdint.h> - -#include "common.h" -#include "baseboard_usbc_config.h" -#include "extpower.h" - -/** - * Configure run-time data structures and operation based on CBI data. This - * typically includes customization for changes in the BOARD_VERSION and - * FW_CONFIG fields in CBI. This routine is called from the baseboard after - * the CBI data has been initialized. - */ -__override_proto void board_cbi_init(void); - -/** - * Initialize the FW_CONFIG from CBI data. If the CBI data is not valid, set the - * FW_CONFIG to the board specific defaults. - */ -__override_proto void board_init_fw_config(void); - -/* - * Check battery disconnect state. - * This function will return if battery is initialized or not. - * @return true - initialized. false - not. - */ -__override_proto bool board_battery_is_initialized(void); - -/* - * Return the board revision number. - */ -uint8_t get_board_id(void); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BASEBOARD_H */ |