diff options
Diffstat (limited to 'baseboard/dedede/baseboard.h')
| -rw-r--r-- | baseboard/dedede/baseboard.h | 269 |
1 files changed, 0 insertions, 269 deletions
diff --git a/baseboard/dedede/baseboard.h b/baseboard/dedede/baseboard.h deleted file mode 100644 index a8a0ed3ff2..0000000000 --- a/baseboard/dedede/baseboard.h +++ /dev/null @@ -1,269 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Dedede board configuration */ - -#ifndef __CROS_EC_BASEBOARD_H -#define __CROS_EC_BASEBOARD_H - -/* - * By default, enable all console messages excepted HC, ACPI and event: - * The sensor stack is generating a lot of activity. - */ -#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC))) - -/* - * Variant EC defines. Pick one: - * VARIANT_DEDEDE_EC_NPCX796FC - */ -#if defined(VARIANT_DEDEDE_EC_NPCX796FC) || \ - defined(VARIANT_KEEBY_EC_NPCX797FC) - /* NPCX7 config */ - #define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ - #define NPCX_TACH_SEL2 0 /* No tach. */ - - /* Internal SPI flash on NPCX7 */ - #define CONFIG_FLASH_SIZE_BYTES (512 * 1024) - #define CONFIG_SPI_FLASH_REGS - #define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */ -#elif defined(VARIANT_DEDEDE_EC_IT8320) || \ - defined(VARIANT_KEEBY_EC_IT8320) - /* IT83XX config */ - #define CONFIG_IT83XX_VCC_1P8V - /* I2C Bus Configuration */ - #define I2C_PORT_EEPROM IT83XX_I2C_CH_A - #define I2C_PORT_BATTERY IT83XX_I2C_CH_B - #define I2C_PORT_SENSOR IT83XX_I2C_CH_C - #define I2C_PORT_SUB_USB_C1 IT83XX_I2C_CH_E - #define I2C_PORT_USB_C0 IT83XX_I2C_CH_F - - #define I2C_ADDR_EEPROM_FLAGS 0x50 - - #define CONFIG_ADC_VOLTAGE_COMPARATOR /* ITE ADC thresholds */ - - #undef CONFIG_UART_TX_BUF_SIZE /* UART */ - #define CONFIG_UART_TX_BUF_SIZE 4096 -#else -#error "Must define a VARIANT_[DEDEDE|KEEBY]_EC!" -#endif - -/* - * The key difference between Keeby and Dedede is that Keeby variants don't have - * a connection to H1 and therefore do not use EFS2. - */ -#if defined(VARIANT_KEEBY_EC_NPCX797FC) || defined(VARIANT_KEEBY_EC_IT8320) -#define KEEBY_VARIANT 1 -#else -#define KEEBY_VARIANT 0 -#endif - -/* - * Remapping of schematic GPIO names to common GPIO names expected (hardcoded) - * in the EC code base. - */ -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_EC_INT_L GPIO_EC_AP_MKBP_INT_L -#define GPIO_EN_PP5000 GPIO_EN_PP5000_U -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV -#if !KEEBY_VARIANT -#define GPIO_PACKET_MODE_EN GPIO_ECH1_PACKET_MODE -#endif -#define GPIO_PCH_DSW_PWROK GPIO_EC_AP_DPWROK -#define GPIO_PCH_PWRBTN_L GPIO_EC_AP_PWR_BTN_ODL -#define GPIO_PCH_RSMRST_L GPIO_EC_AP_RSMRST_L -#define GPIO_PCH_RTCRST GPIO_EC_AP_RTCRST -#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_PCH_SLP_S4_L GPIO_SLP_S4_L -#define GPIO_PCH_WAKE_L GPIO_EC_AP_WAKE_ODL -#define GPIO_PG_EC_RSMRST_ODL GPIO_RSMRST_PWRGD_L -#if KEEBY_VARIANT -#define GPIO_POWER_BUTTON_L GPIO_EC_PWR_BTN_ODL -#else -#define GPIO_POWER_BUTTON_L GPIO_H1_EC_PWR_BTN_ODL -#endif -#define GPIO_RSMRST_L_PGOOD GPIO_RSMRST_PWRGD_L -#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL -#define GPIO_USB_C0_DP_HPD GPIO_EC_AP_USB_C0_HPD -#define GPIO_USB_C1_DP_HPD GPIO_EC_AP_USB_C1_HDMI_HPD -#define GPIO_VOLUME_UP_L GPIO_VOLUP_BTN_ODL -#define GPIO_VOLUME_DOWN_L GPIO_VOLDN_BTN_ODL -#define GPIO_WP GPIO_EC_WP_OD -#define GMR_TABLET_MODE_GPIO_L GPIO_LID_360_L - -/* Common EC defines */ - -/* Work around double CR50 reset by waiting in initial power on. */ -#if !KEEBY_VARIANT -#define CONFIG_BOARD_RESET_AFTER_POWER_ON -#endif - -/* Optional console commands */ -#define CONFIG_CMD_CHARGER_DUMP - -/* Enable AP Reset command for TPM with old firmware version to detect it. */ -#define CONFIG_CMD_AP_RESET_LOG -#define CONFIG_HOSTCMD_AP_RESET - -/* Enable i2ctrace command */ -#define CONFIG_I2C_DEBUG - -/* Assert CCD when a debug device is connected */ -#if !KEEBY_VARIANT -#define CONFIG_ASSERT_CCD_MODE_ON_DTS_CONNECT -#endif - -/* EC Modules */ -#define CONFIG_ADC -#define CONFIG_CRC8 -#define CONFIG_HOSTCMD_ESPI -#define CONFIG_HOSTCMD_EVENTS -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER -#define CONFIG_I2C_BUS_MAY_BE_UNPOWERED -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_POWER_PP5000_CONTROL -#define CONFIG_VBOOT_HASH -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 -#if !KEEBY_VARIANT -#define CONFIG_VBOOT_EFS2 -#endif - -/* Battery */ -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_PRESENT_GPIO GPIO_EC_BATTERY_PRES_ODL -#define CONFIG_BATTERY_REQUESTS_NIL_WHEN_DEAD -#define CONFIG_BATTERY_REVIVE_DISCONNECT -#define CONFIG_BATTERY_SMART - -/* Buttons / Switches */ -#define CONFIG_SWITCH -#define CONFIG_VOLUME_BUTTONS -#define CONFIG_WP_ACTIVE_HIGH - -/* CBI */ -#define CONFIG_CBI_EEPROM -#define CONFIG_BOARD_VERSION_CBI -#if KEEBY_VARIANT -#define CONFIG_EEPROM_CBI_WP -#endif - -/* Charger */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGER -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 256 -#define CONFIG_USB_CHARGER -#define CONFIG_TRICKLE_CHARGING - -/* Keyboard */ -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_MKBP_INPUT_DEVICES - -/* Backlight */ -#define CONFIG_BACKLIGHT_LID -#define GPIO_ENABLE_BACKLIGHT GPIO_EN_BL_OD - -/* LED */ -#define CONFIG_LED_COMMON - -/* Sensors */ -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_USE_GPIO_AND_HOST_EVENT - -/* SoC */ -#define CONFIG_BOARD_HAS_RTC_RESET -#define CONFIG_CHIPSET_JASPERLAKE -#define CONFIG_CHIPSET_RESET_HOOK -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE -#define CONFIG_POWER_S0IX -#define CONFIG_POWER_SLEEP_FAILURE_DETECTION -#define CONFIG_CPU_PROCHOT_ACTIVE_LOW - -/* USB Type-C */ -#define CONFIG_USB_MUX_PI3USB31532 -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_SS_MUX_DFP_ONLY -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP - -/* Temp Sensor */ -#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_EN_PP3300_A -#define CONFIG_TEMP_SENSOR_FIRST_READ_DELAY_MS 500 - -/* USB PD */ -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_DP_HPD_GPIO -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_REV30 -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TRY_SRC -/* #define CONFIG_USB_PD_VBUS_DETECT_CHARGER */ -#define CONFIG_USB_PD_VBUS_MEASURE_CHARGER -#define CONFIG_USB_PD_DECODE_SOP -#if KEEBY_VARIANT -#define CONFIG_USB_PID 0x5059 -#else -#define CONFIG_USB_PID 0x5042 -#endif -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_TCPMV2 -#define CONFIG_USB_DRP_ACC_TRYSRC -#define CONFIG_HOSTCMD_PD_CONTROL - -#if !KEEBY_VARIANT -/* UART COMMAND */ -#define CONFIG_CMD_CHARGEN -#endif - -/* Define typical operating power and max power. */ -#define PD_MAX_VOLTAGE_MV 20000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_POWER_MW 45000 -#define PD_OPERATING_POWER_MW 15000 - -/* TODO(b:147314141): Verify these timings */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ - -#ifndef __ASSEMBLER__ - -#include "common.h" -#include "gpio_signal.h" - -/* Common enums */ -#if defined(VARIANT_DEDEDE_EC_NPCX796FC) -#elif defined(VARIANT_DEDEDE_EC_IT8320) || \ - defined(VARIANT_KEEBY_EC_IT8320) - enum board_vcmp { - VCMP_SNS_PP3300_LOW, - VCMP_SNS_PP3300_HIGH, - VCMP_COUNT - }; -#endif - -/* Interrupt handler for signals that are used to generate ALL_SYS_PGOOD. */ -void baseboard_all_sys_pgood_interrupt(enum gpio_signal signal); - -/* Reset all TCPCs */ -void board_reset_pd_mcu(void); - -/* - * Bit to indicate if the PP3000_A rail's power is good. Will be updated by ADC - * interrupt. - */ -extern uint32_t pp3300_a_pgood; - -#endif /* !__ASSEMBLER__ */ -#endif /* __CROS_EC_BASEBOARD_H */ |