diff options
Diffstat (limited to 'baseboard/goroh/baseboard.h')
| -rw-r--r-- | baseboard/goroh/baseboard.h | 206 |
1 files changed, 0 insertions, 206 deletions
diff --git a/baseboard/goroh/baseboard.h b/baseboard/goroh/baseboard.h deleted file mode 100644 index 55fa0ffab7..0000000000 --- a/baseboard/goroh/baseboard.h +++ /dev/null @@ -1,206 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Goroh board configuration */ - -#ifndef __CROS_EC_BASEBOARD_H -#define __CROS_EC_BASEBOARD_H - -/* IT81202-bx config */ -/* - * NOTE: we need to make correct VCC voltage selection here if EC's VCC isn't - * connect to 1.8v on other versions. - */ -#define CONFIG_IT83XX_VCC_1P8V - -/* - * On power-on, H1 releases the EC from reset but then quickly asserts and - * releases the reset a second time. This means the EC sees 2 resets: - * (1) power-on reset, (2) reset-pin reset. This config will - * allow the second reset to be treated as a power-on. - */ -#define CONFIG_BOARD_RESET_AFTER_POWER_ON -#define CONFIG_CHIPSET_MT8192 -#define CONFIG_EXTPOWER_GPIO -#define CONFIG_HIBERNATE_WAKE_PINS_DYNAMIC - -/* Chipset */ -#define CONFIG_CMD_AP_RESET_LOG -#define CONFIG_CMD_POWERINDEBUG -#define CONFIG_HOST_COMMAND_STATUS -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_LOW_POWER_S0 -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_COMMON -#define CONFIG_PWM -#define CONFIG_VBOOT_HASH -#define CONFIG_VOLUME_BUTTONS -#define CONFIG_WP_ACTIVE_HIGH - -/* Battery */ -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_PRESENT_GPIO GPIO_EC_BATT_PRES_ODL -#define CONFIG_BATTERY_SMART - -/* BC12 */ -#define CONFIG_BC12_DETECT_MT6360 -#define CONFIG_BC12_DETECT_PI3USB9201 -#undef CONFIG_BC12_SINGLE_DRIVER -#define CONFIG_USB_CHARGER - -/* Charger */ -#define ADC_AMON_BMON ADC_CHARGER_AMON_R /* ADC name remap */ -#define ADC_PSYS ADC_CHARGER_PMON /* ADC name remap */ -#define ADC_VBUS ADC_VBUS_C0 /* ADC name remap */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGER -#define CONFIG_CHARGE_RAMP_HW -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 512 -#define CONFIG_CHARGER_ISL9238C -#define CONFIG_CHARGER_MAINTAIN_VBAT -#define CONFIG_CHARGER_OTG -#define CONFIG_CHARGER_PSYS -#define CONFIG_CHARGER_PSYS_READ -#define CONFIG_CHARGER_SENSE_RESISTOR 10 /* BOARD_RS2 */ -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 /* BOARD_RS1 */ -#define CONFIG_CMD_CHARGER_ADC_AMON_BMON - -/* Keyboard */ -#define CONFIG_CMD_KEYBOARD -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_PROTOCOL_MKBP -#define CONFIG_MKBP_USE_GPIO - -/* I2C */ -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER -#define CONFIG_I2C_PASSTHRU_RESTRICTED -#define CONFIG_I2C_VIRTUAL_BATTERY -#define I2C_PORT_CHARGER IT83XX_I2C_CH_A -#define I2C_PORT_BATTERY IT83XX_I2C_CH_A -#define I2C_PORT_ACCEL IT83XX_I2C_CH_B -#define I2C_PORT_PPC0 IT83XX_I2C_CH_C -#define I2C_PORT_PPC1 IT83XX_I2C_CH_E -#define I2C_PORT_USB_MUX0 IT83XX_I2C_CH_C -#define I2C_PORT_USB_MUX1 IT83XX_I2C_CH_E -#define I2C_PORT_VIRTUAL_BATTERY I2C_PORT_BATTERY -#define CONFIG_SMBUS_PEC - -/* LED */ -#define CONFIG_LED_COMMON - -/* PD / USB-C / PPC */ -#define CONFIG_CMD_PPC_DUMP -#define CONFIG_HOSTCMD_PD_CONTROL -#define CONFIG_IT83XX_TUNE_CC_PHY -#define CONFIG_USB_MUX_VIRTUAL -#define CONFIG_USBC_PPC -#define CONFIG_USBC_PPC_DEDICATED_INT -#define CONFIG_USBC_PPC_POLARITY -#define CONFIG_USBC_PPC_SYV682C -#define CONFIG_USBC_PPC_SYV682X_SMART_DISCHARGE -#define CONFIG_USBC_PPC_VCONN -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP -#define CONFIG_USB_DRP_ACC_TRYSRC -#define CONFIG_USB_MUX_IT5205 /* C0 */ -#define CONFIG_USB_MUX_PS8743 /* C1 */ -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_DECODE_SOP -#define CONFIG_USB_PD_DISCHARGE -#define CONFIG_USB_PD_DISCHARGE_PPC -#define CONFIG_USB_PD_DP_HPD_GPIO -#define CONFIG_USB_PD_DP_HPD_GPIO_CUSTOM -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_FRS_PPC -#define CONFIG_USB_PD_ITE_ACTIVE_PORT_COUNT 2 -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_PD_REV30 -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_TCPM_ITE_ON_CHIP -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TCPMV2 -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_PD_VBUS_DETECT_PPC -#define CONFIG_USB_PD_VBUS_MEASURE_ADC_EACH_PORT -#define CONFIG_USB_PID 0x5566 /* TODO: update PID */ -#define CONFIG_USB_POWER_DELIVERY - -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 60000 -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ - -/* USB-A */ -#define CONFIG_USB_PORT_POWER_DUMB -#define USB_PORT_COUNT USBA_PORT_COUNT - -/* UART */ -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 4096 - -/* Sensor */ -#ifdef HAS_TASK_MOTIONSENSE -#define CONFIG_CMD_ACCEL_INFO -#define CONFIG_CMD_ACCELS - -#define CONFIG_ACCEL_FIFO -#define CONFIG_ACCEL_FIFO_SIZE 256 -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) -#define CONFIG_ACCEL_INTERRUPTS -#endif - -/* SPI / Host Command */ -#define CONFIG_SPI - -/* MKBP */ -#define CONFIG_MKBP_EVENT - -#define CONFIG_KEYBOARD_PROTOCOL_MKBP -#define CONFIG_MKBP_USE_GPIO - -/* Voltage regulator control */ -#define CONFIG_HOSTCMD_REGULATOR - -/* Define the host events which are allowed to wakeup AP in S3. */ -#define CONFIG_MKBP_HOST_EVENT_WAKEUP_MASK \ - (EC_HOST_EVENT_MASK(EC_HOST_EVENT_AC_CONNECTED) | \ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_AC_DISCONNECTED) | \ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_LID_OPEN) | \ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_MODE_CHANGE) | \ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_POWER_BUTTON)) - -/* GPIO name remapping */ -#define GPIO_EN_HDMI_PWR GPIO_EC_X_GPIO1 -#define GPIO_USB_C1_FRS_EN GPIO_EC_X_GPIO1 -#define GPIO_USB_C1_PPC_INT_ODL GPIO_X_EC_GPIO2 -#define GPIO_PS185_EC_DP_HPD GPIO_X_EC_GPIO2 -#define GPIO_USB_C1_DP_IN_HPD GPIO_EC_X_GPIO3 -#define GPIO_PS185_PWRDN_ODL GPIO_EC_X_GPIO3 - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" -#include "power/mt8192.h" - -enum board_sub_board { - SUB_BOARD_NONE = -1, - SUB_BOARD_TYPEC, - SUB_BOARD_HDMI, - SUB_BOARD_COUNT, -}; - -int board_get_version(void); -void board_reset_pd_mcu(void); -#endif /* !__ASSEMBLER__ */ -#endif /* __CROS_EC_BASEBOARD_H */ |