diff options
Diffstat (limited to 'baseboard/grunt/baseboard.h')
| -rw-r--r-- | baseboard/grunt/baseboard.h | 260 |
1 files changed, 0 insertions, 260 deletions
diff --git a/baseboard/grunt/baseboard.h b/baseboard/grunt/baseboard.h deleted file mode 100644 index c97ece285f..0000000000 --- a/baseboard/grunt/baseboard.h +++ /dev/null @@ -1,260 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Grunt family-specific configuration */ - -#ifndef __CROS_EC_BASEBOARD_H -#define __CROS_EC_BASEBOARD_H - -#if (defined(VARIANT_GRUNT_TCPC_0_ANX3429) \ - + defined(VARIANT_GRUNT_TCPC_0_ANX3447)) != 1 -#error Must choose VARIANT_GRUNT_TCPC_0_ANX3429 or VARIANT_GRUNT_TCPC_0_ANX3447 -#endif - -/* NPCX7 config */ -#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ -#define NPCX_TACH_SEL2 0 /* No tach. */ -#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ - -/* Internal SPI flash on NPCX7 */ -/* Flash is 1MB but reserve half for future use. */ -#define CONFIG_FLASH_SIZE_BYTES (512 * 1024) -#define CONFIG_SPI_FLASH_REGS -#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */ - -/* - * Enable 1 slot of secure temporary storage to support - * suspend/resume with read/write memory training. - */ -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 - -#define CONFIG_ADC -#define CONFIG_BACKLIGHT_LID -#define CONFIG_BACKLIGHT_LID_ACTIVE_LOW -#define CONFIG_CMD_AP_RESET_LOG -#define CONFIG_HIBERNATE_PSL -#define CONFIG_HOSTCMD_LPC -#define CONFIG_HOSTCMD_SKUID -#define CONFIG_I2C -#define CONFIG_I2C_BUS_MAY_BE_UNPOWERED -#define CONFIG_I2C_CONTROLLER -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_LOW_POWER_S0 -#define CONFIG_LTO -#define CONFIG_PWM -#define CONFIG_PWM_KBLIGHT -#define CONFIG_TEMP_SENSOR -#define CONFIG_THERMISTOR_NCP15WB -#define CONFIG_VBOOT_HASH -#define CONFIG_VOLUME_BUTTONS - -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_PRESENT_GPIO GPIO_EC_BATT_PRES_L -#define CONFIG_BATTERY_REVIVE_DISCONNECT -#define CONFIG_BATTERY_SMART - -#define CONFIG_BC12_DETECT_MAX14637 -#define CONFIG_CHARGER -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGER_DISCHARGE_ON_AC - -/* - * This limit impairs compatibility with BC1.2 chargers that are not actually - * capable of supplying 500 mA of current. When the charger is paralleled with - * the battery, raising this limit allows the power system to draw more current - * from the charger during startup. This improves compatibility with system - * batteries that may become excessively imbalanced after extended periods of - * rest. - * - * See also b/111214767 - */ -#define CONFIG_CHARGER_INPUT_CURRENT 512 -#define CONFIG_CHARGER_ISL9238 -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 -#define CONFIG_CHARGE_RAMP_HW -#define CONFIG_USB_CHARGER - -#define CONFIG_CHIPSET_STONEY -#define CONFIG_CHIPSET_RESET_HOOK -/* - * ACOK from ISL9238 sometimes has a negative pulse after connecting - * USB-C power. We want to ignore it. b/77455171 - */ -#undef CONFIG_EXTPOWER_DEBOUNCE_MS -#define CONFIG_EXTPOWER_DEBOUNCE_MS 200 -#define CONFIG_EXTPOWER_GPIO -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_SHUTDOWN_PAUSE_IN_S5 -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 - -/* - * On power-on, H1 releases the EC from reset but then quickly asserts and - * releases the reset a second time. This means the EC sees 2 resets: - * (1) power-on reset, (2) reset-pin reset. This config will - * allow the second reset to be treated as a power-on. - */ -#define CONFIG_BOARD_RESET_AFTER_POWER_ON - - -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_PROTOCOL_8042 - -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_TCPMV1 -#define CONFIG_HOSTCMD_PD_CONTROL -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_COMM_LOCKED -#define CONFIG_USB_PD_DISCHARGE_PPC -#define CONFIG_USB_PD_DP_HPD_GPIO -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_PD_TCPC_LOW_POWER -#ifdef VARIANT_GRUNT_TCPC_0_ANX3429 -#define CONFIG_USB_PD_TCPM_ANX3429 -#elif defined(VARIANT_GRUNT_TCPC_0_ANX3447) -#define CONFIG_USB_PD_TCPM_ANX7447 -#endif -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_USB_PD_TCPM_PS8751 -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_PD_VBUS_DETECT_PPC -#define CONFIG_USBC_PPC_SN5S330 -#define CONFIG_USBC_PPC_DEDICATED_INT -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_SS_MUX_DFP_ONLY -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP - -/* USB-A config */ -#define CONFIG_USB_PORT_POWER_DUMB -#define USB_PORT_COUNT 2 - -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ - -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 45000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 - -/* - * Require PD negotiation to be complete when we are in a low-battery condition - * prior to releasing depthcharge to the kernel. - */ -#define CONFIG_CHARGER_LIMIT_POWER_THRESH_CHG_MW 15001 -#define CONFIG_CHARGER_LIMIT_POWER_THRESH_BAT_PCT 3 - -/* Increase length of history buffer for port80 messages. */ -#undef CONFIG_PORT80_HISTORY_LEN -#define CONFIG_PORT80_HISTORY_LEN 256 - -#define I2C_PORT_BATTERY I2C_PORT_POWER -#define I2C_PORT_CHARGER I2C_PORT_POWER -#define I2C_PORT_POWER NPCX_I2C_PORT0_0 -#define I2C_PORT_TCPC0 NPCX_I2C_PORT1_0 -#define I2C_PORT_TCPC1 NPCX_I2C_PORT2_0 -#define I2C_PORT_THERMAL_AP NPCX_I2C_PORT3_0 -#define I2C_PORT_SENSOR NPCX_I2C_PORT7_0 -/* Accelerometer and Gyroscope are the same device. */ -#define I2C_PORT_ACCEL I2C_PORT_SENSOR - -/* Sensors */ -#define CONFIG_MKBP_EVENT -#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT - -/* Thermal */ -#define CONFIG_TEMP_SENSOR_SB_TSI - -#ifndef VARIANT_GRUNT_NO_SENSORS -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is a power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs. */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) -#endif /* VARIANT_GRUNT_NO_SENSORS */ - -#define USB_PD_PORT_ANX74XX 0 -#define USB_PD_PORT_PS8751 1 - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "math_util.h" -#include "registers.h" - -enum adc_channel { - ADC_TEMP_SENSOR_CHARGER, - ADC_TEMP_SENSOR_SOC, - ADC_VBUS, - ADC_SKU_ID1, - ADC_SKU_ID2, - ADC_CH_COUNT -}; - -enum power_signal { - X86_SLP_S3_N, - X86_SLP_S5_N, - X86_S0_PGOOD, - X86_S5_PGOOD, - POWER_SIGNAL_COUNT -}; - -enum temp_sensor_id { - TEMP_SENSOR_CHARGER = 0, - TEMP_SENSOR_SOC, - TEMP_SENSOR_CPU, - TEMP_SENSOR_COUNT -}; - -enum sensor_id { - LID_ACCEL, - BASE_ACCEL, - BASE_GYRO, - SENSOR_COUNT, -}; - -/* - * Matrix to rotate accelerators into the standard reference frame. The default - * is the identity which is correct for the reference design. Variations of - * Grunt may need to change it for manufacturability. - * For the lid: - * +x to the right - * +y up - * +z out of the page - * - * The principle axes of the body are aligned with the lid when the lid is in - * the 180 degree position (open, flat). - * - * Boards within the Grunt family may need to modify this definition at - * board_init() time. - */ -extern mat33_fp_t grunt_base_standard_ref; - -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK (1 << LID_ACCEL) - -void board_reset_pd_mcu(void); - -/* Common definition for the USB PD interrupt handlers. */ -void tcpc_alert_event(enum gpio_signal signal); -void ppc_interrupt(enum gpio_signal signal); -void anx74xx_cable_det_interrupt(enum gpio_signal signal); - -int board_get_version(void); -int board_is_convertible(void); -void board_update_sensor_config_from_sku(void); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BASEBOARD_H */ |