diff options
Diffstat (limited to 'baseboard/guybrush/baseboard.h')
| -rw-r--r-- | baseboard/guybrush/baseboard.h | 373 |
1 files changed, 0 insertions, 373 deletions
diff --git a/baseboard/guybrush/baseboard.h b/baseboard/guybrush/baseboard.h deleted file mode 100644 index ef1338c5d5..0000000000 --- a/baseboard/guybrush/baseboard.h +++ /dev/null @@ -1,373 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Guybrush baseboard configuration */ - -#ifndef __CROS_EC_BASEBOARD_H -#define __CROS_EC_BASEBOARD_H - -/* NPCX9 config */ -#define CONFIG_PORT80_4_BYTE -#define NPCX9_PWM1_SEL 1 /* GPIO C2 is used as PWM1. */ -#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ - -/* Optional features */ -#define CONFIG_ASSERT_CCD_MODE_ON_DTS_CONNECT -#define CONFIG_LTO /* Link-Time Optimizations to reduce code size */ -#define CONFIG_I2C_DEBUG /* Print i2c traces */ -#define CONFIG_CMD_S5_TIMEOUT /* Allow a user-specified timeout to exit S5 */ - -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 4096 - -/* Vboot Config */ -#define CONFIG_CRC8 -#define CONFIG_VBOOT_EFS2 -#define CONFIG_VBOOT_HASH -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE - -/* CBI Config */ -#define CONFIG_CBI_EEPROM -#define CONFIG_BOARD_VERSION_CBI - -/* Power Config */ -#define CONFIG_CHIPSET_X86_RSMRST_DELAY -#undef CONFIG_EXTPOWER_DEBOUNCE_MS -#define CONFIG_EXTPOWER_DEBOUNCE_MS 200 -#define CONFIG_EXTPOWER_GPIO -#define CONFIG_HIBERNATE_PSL -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_TO_PCH_CUSTOM -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_S0IX -#define CONFIG_POWER_SLEEP_FAILURE_DETECTION -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE -#define G3_TO_PWRBTN_DELAY_MS 16 -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_EN_PWR_A GPIO_EN_PWR_S5 -#define GPIO_PCH_PWRBTN_L GPIO_EC_SOC_PWR_BTN_L -#define GPIO_PCH_RSMRST_L GPIO_EC_SOC_RSMRST_L -#define GPIO_PCH_SLP_S0_L GPIO_SLP_S3_S0I3_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L -#define GPIO_PCH_SLP_S5_L GPIO_SLP_S5_L -#define GPIO_PCH_SYS_PWROK GPIO_EC_SOC_PWR_GOOD -#define GPIO_PCH_WAKE_L GPIO_EC_SOC_WAKE_L -#define GPIO_POWER_BUTTON_L GPIO_MECH_PWR_BTN_ODL -#define GPIO_S0_PGOOD GPIO_PG_PCORE_S0_R_OD -#define GPIO_S5_PGOOD GPIO_PG_PWR_S5 -#define GPIO_SYS_RESET_L GPIO_EC_SYS_RST_L -#define SAFE_RESET_VBUS_DELAY_MS 900 -#define SAFE_RESET_VBUS_MV 5000 -/* - * On power-on, H1 releases the EC from reset but then quickly asserts and - * releases the reset a second time. This means the EC sees 2 resets: - * (1) power-on reset, (2) reset-pin reset. This config will - * allow the second reset to be treated as a power-on. - */ -#define CONFIG_BOARD_RESET_AFTER_POWER_ON - -/* Thermal Config */ -#define CONFIG_ADC -#define CONFIG_AMD_SB_RMI -#define CONFIG_AMD_STT -#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B -#define CONFIG_THROTTLE_AP -#define CONFIG_TEMP_SENSOR_SB_TSI -#define CONFIG_TEMP_SENSOR_TMP112 -#define CONFIG_THERMISTOR -#define CONFIG_CPU_PROCHOT_ACTIVE_LOW -#define GPIO_CPU_PROCHOT GPIO_PROCHOT_ODL - -/* Flash Config */ -/* See config_chip-npcx9.h for SPI flash configuration */ -#undef CONFIG_SPI_FLASH /* Don't enable external flash interface */ -#define GPIO_WP_L GPIO_EC_WP_L - -/* Host communication */ -#define CONFIG_CMD_CHARGEN -#define CONFIG_HOSTCMD_ESPI -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_USE_GPIO_AND_HOST_EVENT -#define GPIO_EC_INT_L GPIO_EC_SOC_INT_L - -/* Chipset config */ -#define CONFIG_CHIPSET_CEZANNE -#define CONFIG_CHIPSET_CAN_THROTTLE -#define CONFIG_CHIPSET_RESET_HOOK - -/* Keyboard Config */ -#define CONFIG_KEYBOARD_BACKLIGHT - -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_KEYBOARD_VIVALDI -#define GPIO_EN_KEYBOARD_BACKLIGHT GPIO_EN_KB_BL -#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV - -/* Sensors */ -#ifdef HAS_TASK_MOTIONSENSE - -#define CONFIG_TABLET_MODE -#define CONFIG_GMR_TABLET_MODE -#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE -#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL - -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is a power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs. */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) - -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK (1 << LID_ACCEL) -#endif /* HAS_TASK_MOTIONSENSE */ - -/* Backlight config */ -#define CONFIG_BACKLIGHT_LID -#define CONFIG_BACKLIGHT_LID_ACTIVE_LOW -#define GPIO_ENABLE_BACKLIGHT_L GPIO_EC_DISABLE_DISP_BL - -/* Battery Config */ -#define CONFIG_BATTERY_PRESENT_GPIO GPIO_EC_BATT_PRES_ODL -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_REVIVE_DISCONNECT -#define CONFIG_BATTERY_SMART -#define CONFIG_BATTERY_V2 -#define CONFIG_BATTERY_COUNT 1 -#define CONFIG_HOSTCMD_BATTERY_V2 -#define CONFIG_BC12_DETECT_PI3USB9201 - -/* Charger Config */ -#define CONFIG_CHARGER -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 512 -#define CONFIG_CHARGER_ISL9241 -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 - -/* - * EC will boot AP to depthcharge if: (BAT >= 2%) || (AC >= 50W) - * CONFIG_CHARGER_LIMIT_* is not set, so there is no additional restriction on - * Depthcharge to boot OS. - */ -#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 50000 - -/* - * We would prefer to use CONFIG_CHARGE_RAMP_HW to enable legacy BC1.2 charging - * but that feature of ISL9241 is broken (b/160287056) so we have to use - * CONFIG_CHARGE_RAMP_SW instead. - */ -#define CONFIG_CHARGE_RAMP_SW - -/* USB Type C and USB PD config */ -#define CONFIG_USB_PD_REV30 -#define CONFIG_USB_PD_TCPMV2 -#define CONFIG_USB_PD_DECODE_SOP -#define CONFIG_USB_DRP_ACC_TRYSRC -/* TODO: Enable TCPMv2 Fast Role Swap (FRS) */ -#define CONFIG_HOSTCMD_PD_CONTROL -#define CONFIG_CMD_TCPC_DUMP -#define CONFIG_USB_CHARGER -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_5V_EN_CUSTOM -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_DISCHARGE_TCPC -#define CONFIG_USB_PD_DP_HPD_GPIO -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_USB_PD_TCPM_NCT38XX -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_VBUS_DETECT_TCPC -#define CONFIG_USBC_PPC -#define CONFIG_USBC_PPC_SBU -#define CONFIG_USBC_PPC_AOZ1380 -#define CONFIG_USBC_RETIMER_PI3HDX1204 -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_SS_MUX_DFP_ONLY -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USBC_PPC_NX20P3483 -#define CONFIG_USBC_RETIMER_PS8811 -#define CONFIG_USBC_RETIMER_PS8818 -#define CONFIG_USB_MUX_RUNTIME_CONFIG -#define CONFIG_USB_MUX_AMD_FP6 - -#define GPIO_USB_C0_DP_HPD GPIO_USB_C0_HPD -#define GPIO_USB_C1_DP_HPD GPIO_USB_C1_HPD - -#define CONFIG_IO_EXPANDER -#define CONFIG_IO_EXPANDER_NCT38XX -#define CONFIG_IO_EXPANDER_PORT_COUNT USBC_PORT_COUNT - -/* TODO(b/176988382): Tune values for guybrush */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ - -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_CURRENT_MA 5000 -#define PD_MAX_VOLTAGE_MV 20000 -/* Max Power = 100 W */ -#define PD_MAX_POWER_MW ((PD_MAX_VOLTAGE_MV * PD_MAX_CURRENT_MA) / 1000) - -/* USB-A config */ -#define USB_PORT_COUNT USBA_PORT_COUNT -#define CONFIG_USB_PORT_POWER_SMART -#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY -#define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP -#define CONFIG_USB_PORT_POWER_SMART_INVERTED - -#define GPIO_USB1_ILIM_SEL IOEX_USB_A0_LIMIT_SDP -#define GPIO_USB2_ILIM_SEL IOEX_USB_A1_LIMIT_SDP_DB - -/* Round up 3250 max current to multiple of 128mA for ISL9241 AC prochot. */ -#define GUYBRUSH_AC_PROCHOT_CURRENT_MA 3328 - -/* - * USB ID - This is allocated specifically for Guybrush - */ -#define CONFIG_USB_PID 0x504D - -/* BC 1.2 */ -/* - * For legacy BC1.2 charging with CONFIG_CHARGE_RAMP_SW, ramp up input current - * until voltage drops to 4.5V. Don't go lower than this to be kind to the - * charger (see b/67964166). - */ -#define BC12_MIN_VOLTAGE 4500 - -/* I2C Bus Configuration */ -#define CONFIG_I2C -#define CONFIG_I2C_BUS_MAY_BE_UNPOWERED -#define CONFIG_I2C_CONTROLLER -#define CONFIG_I2C_UPDATE_IF_CHANGED -#define I2C_PORT_TCPC0 NPCX_I2C_PORT0_0 -#define I2C_PORT_TCPC1 NPCX_I2C_PORT1_0 -#define I2C_PORT_BATTERY NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_MUX NPCX_I2C_PORT3_0 -#define I2C_PORT_POWER NPCX_I2C_PORT4_1 -#define I2C_PORT_CHARGER I2C_PORT_POWER -#define I2C_PORT_EEPROM NPCX_I2C_PORT5_0 -#define I2C_PORT_SENSOR NPCX_I2C_PORT6_1 -#define I2C_PORT_THERMAL_AP NPCX_I2C_PORT7_0 -#define I2C_ADDR_EEPROM_FLAGS 0x50 - -/* Volume Button Config */ -#define CONFIG_VOLUME_BUTTONS -#define GPIO_VOLUME_UP_L GPIO_VOLUP_BTN_ODL -#define GPIO_VOLUME_DOWN_L GPIO_VOLDN_BTN_ODL - -/* Fan Config */ -#define CONFIG_FANS FAN_CH_COUNT -/* TODO: Set CONFIG_FAN_INIT_SPEED, defaults to 100 */ - -/* LED Config */ -#define CONFIG_PWM -#define CONFIG_PWM_KBLIGHT - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -/* Power input signals */ -enum power_signal { - X86_SLP_S0_N, /* SOC -> SLP_S3_S0I3_L */ - X86_SLP_S3_N, /* SOC -> SLP_S3_L */ - X86_SLP_S5_N, /* SOC -> SLP_S5_L */ - - X86_S0_PGOOD, /* PMIC -> S0_PWROK_OD */ - X86_S5_PGOOD, /* PMIC -> S5_PWROK */ - - /* Number of X86 signals */ - POWER_SIGNAL_COUNT, -}; - -/* USB-C ports */ -enum usbc_port { - USBC_PORT_C0 = 0, - USBC_PORT_C1, - USBC_PORT_COUNT -}; - -/* USB-A ports */ -enum usba_port { - USBA_PORT_A0 = 0, - USBA_PORT_A1, - USBA_PORT_COUNT -}; - -/* TMP112 sensors */ -enum tmp112_sensor { - TMP112_SOC, - TMP112_AMB, - TMP112_COUNT, -}; - -enum sensor_id { - LID_ACCEL, - BASE_ACCEL, - BASE_GYRO, - SENSOR_COUNT -}; - -/* PWM Channels */ -enum pwm_channel { - PWM_CH_FAN = 0, - PWM_CH_KBLIGHT, - PWM_CH_LED_CHRG, - PWM_CH_LED_FULL, - PWM_CH_COUNT -}; - -/* Fan Channels */ -enum fan_channel { - FAN_CH_0 = 0, - /* Number of FAN channels */ - FAN_CH_COUNT, -}; -enum mft_channel { - MFT_CH_0 = 0, - /* Number of MFT channels */ - MFT_CH_COUNT, -}; - -/* Common definition for the USB PD interrupt handlers. */ -void tcpc_alert_event(enum gpio_signal signal); -void bc12_interrupt(enum gpio_signal signal); -void ppc_interrupt(enum gpio_signal signal); -void sbu_fault_interrupt(enum ioex_signal signal); - -void baseboard_en_pwr_pcore_s0(enum gpio_signal signal); -void baseboard_en_pwr_s0(enum gpio_signal signal); - -int board_get_soc_temp_k(int idx, int *temp_k); - -/* CBI utility functions */ -uint32_t get_sku_id(void); -uint32_t get_board_version(void); -uint32_t get_fw_config(void); -/* Board callback after CBI has been initialized */ -__overridable void board_cbi_init(void); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BASEBOARD_H */ |