diff options
Diffstat (limited to 'baseboard/hatch/baseboard.h')
| -rw-r--r-- | baseboard/hatch/baseboard.h | 222 |
1 files changed, 0 insertions, 222 deletions
diff --git a/baseboard/hatch/baseboard.h b/baseboard/hatch/baseboard.h deleted file mode 100644 index bf9140b33f..0000000000 --- a/baseboard/hatch/baseboard.h +++ /dev/null @@ -1,222 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Hatch baseboard configuration */ - -#ifndef __CROS_EC_BASEBOARD_H -#define __CROS_EC_BASEBOARD_H - -#include "compiler.h" -#include "stdbool.h" - -/* - * By default, enable all console messages excepted HC, ACPI and event: - * The sensor stack is generating a lot of activity. - */ -#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC))) -#undef CONFIG_HOSTCMD_DEBUG_MODE -#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF - -/* NPCX7 config */ -#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ -#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ -/* Internal SPI flash on NPCX796FC is 512 kB */ -#define CONFIG_FLASH_SIZE_BYTES (512 * 1024) -#define CONFIG_SPI_FLASH_REGS -#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */ -#define CONFIG_I2C - -/* Optional console commands */ -#define CONFIG_CMD_CHARGER_DUMP - -/* EC Defines */ -#define CONFIG_ADC -#define CONFIG_BOARD_VERSION_CBI -#define CONFIG_CRC8 -#define CONFIG_CBI_EEPROM -#define CONFIG_DPTF -#define CONFIG_HIBERNATE_PSL -#define CONFIG_LED_ONOFF_STATES -#define CONFIG_LTO -#define CONFIG_PWM -#define CONFIG_VBOOT_HASH -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 - -/* Chipset config */ -#define CONFIG_CHIPSET_COMETLAKE -#define CONFIG_CHIPSET_HAS_PRE_INIT_CALLBACK -#define CONFIG_CHIPSET_RESET_HOOK -#define CONFIG_CPU_PROCHOT_ACTIVE_LOW -#define CONFIG_EXTPOWER_GPIO -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_PP5000_CONTROL -#define CONFIG_POWER_S0IX -#define CONFIG_POWER_SLEEP_FAILURE_DETECTION -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE - -/* Common Keyboard Defines */ -#define CONFIG_CMD_KEYBOARD -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_KEYPAD -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2 - -/* Sensors */ -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_USE_GPIO_AND_HOST_EVENT -#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT - -/* Don't wake up from suspend on any MKBP event */ -#define CONFIG_MKBP_EVENT_WAKEUP_MASK 0 - -/* I2C_PORT_ACCEL needs to be defined for i2c transactions */ -#define I2C_PORT_ACCEL I2C_PORT_SENSOR - -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#if !defined(BOARD_PALKIA) -#define CONFIG_ACCEL_FIFO -/* FIFO size is in power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) - -/* Sensor console commands */ -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO -#endif /* !BOARD_PALKIA */ - -/* Common charger defines */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGE_MANAGER_EXTERNAL_POWER_LIMIT -#define CONFIG_CHARGER -#define CONFIG_CHARGER_BQ25710 -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 512 /* Allow low-current USB charging */ -#undef CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON -#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 1 -#define CONFIG_CHARGE_RAMP_HW -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 -/* - * Don't allow the system to boot to S0 when the battery is low and unable to - * communicate on locked systems (which haven't PD negotiated) - */ -#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON_WITH_BATT 15000 -#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 15001 - -/* Common battery defines */ -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION" -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_HW_PRESENT_CUSTOM -#define CONFIG_BATTERY_PRESENT_CUSTOM -#define CONFIG_BATTERY_REVIVE_DISCONNECT -#define CONFIG_BATTERY_SMART -#undef CONFIG_BATT_HOST_FULL_FACTOR -#define CONFIG_BATT_HOST_FULL_FACTOR 100 - -/* USB Type C and USB PD defines */ -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_TCPMV1 -#if defined(BOARD_PALKIA) -#define CONFIG_USB_PD_PORT_MAX_COUNT 1 -#else -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#endif -#define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0 -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_DISCHARGE_PPC -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_PD_VBUS_DETECT_PPC -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USBC_PPC_SN5S330 -#define CONFIG_USBC_PPC_VCONN -#define CONFIG_USBC_SS_MUX -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP -#define CONFIG_USBC_PPC_DEDICATED_INT - -#define CONFIG_HOSTCMD_PD_CONTROL -#define CONFIG_CMD_PPC_DUMP - -/* Include CLI command needed to support CCD testing. */ -#define CONFIG_CMD_CHARGEN - -#define USB_PD_PORT_TCPC_0 0 -#if CONFIG_USB_PD_PORT_MAX_COUNT > 1 -#define USB_PD_PORT_TCPC_1 1 -#endif - -/* BC 1.2 */ -#define CONFIG_USB_CHARGER - -#if !defined(BOARD_PALKIA) -/* Common Sensor Defines */ -#define CONFIG_TABLET_MODE -#endif - -/* TODO(b/122273953): Use correct PD delay values */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ - -/* TODO(b/122273953): Use correct PD power values */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 60000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 - -/* I2C Bus Configuration */ -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER -#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0 -#define I2C_PORT_PPC0 NPCX_I2C_PORT1_0 -#define I2C_PORT_TCPC1 NPCX_I2C_PORT2_0 -#define I2C_PORT_TCPC0 NPCX_I2C_PORT3_0 -#define I2C_PORT_THERMAL NPCX_I2C_PORT4_1 -#define I2C_PORT_POWER NPCX_I2C_PORT5_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 -#define I2C_ADDR_EEPROM_FLAGS 0x50 -#define I2C_PORT_BATTERY I2C_PORT_POWER -#define I2C_PORT_CHARGER I2C_PORT_POWER - -/* Other common defines */ -#define CONFIG_BACKLIGHT_LID -#define GPIO_ENABLE_BACKLIGHT GPIO_EDP_BKLTEN_OD - -#define PP5000_PGOOD_POWER_SIGNAL_MASK POWER_SIGNAL_MASK(X86_PP5000_A_PGOOD) - -#ifndef __ASSEMBLER__ - -enum mst_source { - MST_TYPE_C0, - MST_TYPE_C1, - MST_HDMI, -}; - -/* Forward declare common (within Hatch) board-specific functions */ -bool board_has_kb_backlight(void); -unsigned char get_board_sku(void); -unsigned char get_board_id(void); -void board_reset_pd_mcu(void); -void baseboard_mst_enable_control(enum mst_source, int level); -bool board_is_convertible(void); - -FORWARD_DECLARE_ENUM(battery_present); - -/* Check with variant about battery presence. */ -enum battery_present variant_battery_present(void); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BASEBOARD_H */ |