diff options
Diffstat (limited to 'baseboard/kukui/baseboard.h')
| -rw-r--r-- | baseboard/kukui/baseboard.h | 357 |
1 files changed, 0 insertions, 357 deletions
diff --git a/baseboard/kukui/baseboard.h b/baseboard/kukui/baseboard.h deleted file mode 100644 index 87ebeb40e1..0000000000 --- a/baseboard/kukui/baseboard.h +++ /dev/null @@ -1,357 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Kukui board configuration */ - -#ifndef __CROS_EC_BASEBOARD_H -#define __CROS_EC_BASEBOARD_H - -/* - * Variant battery defines, pick one: - * VARIANT_KUKUI_BATTERY_MAX17055 - * VARIANT_KUKUI_BATTERY_MM8013 - * VARIANT_KUKUI_BATTERY_BQ27541 - * VARIANT_KUKUI_BATTERY_SMART - */ -#if defined(VARIANT_KUKUI_BATTERY_MAX17055) -#define CONFIG_BATTERY_MAX17055 -#define CONFIG_BATTERY_MAX17055_ALERT -#define BATTERY_MAX17055_RSENSE 5 /* m-ohm */ -#elif defined(VARIANT_KUKUI_BATTERY_MM8013) -#define CONFIG_BATTERY_MM8013 -#elif defined(VARIANT_KUKUI_BATTERY_BQ27541) -#define CONFIG_BATTERY_BQ27541 -#elif defined(VARIANT_KUKUI_BATTERY_SMART) -#define CONFIG_BATTERY_SMART -#define CONFIG_BATTERY_FUEL_GAUGE -#else -#error Must define a VARIANT_KUKUI_BATTERY -#endif /* VARIANT_KUKUI_BATTERY */ - -/* - * Variant charger defines, pick one: - * VARIANT_KUKUI_CHARGER_MT6370 - * VARIANT_KUKUI_CHARGER_ISL9238 - */ -#if defined(VARIANT_KUKUI_CHARGER_MT6370) -#define CONFIG_CHARGER_MT6370 -#define CONFIG_CHARGER_MT6370_BC12_GPIO -#define CONFIG_CHARGE_RAMP_HW -#define CONFIG_CHARGER_OTG -#define CONFIG_CHARGER_PROFILE_OVERRIDE -#define CONFIG_USB_PD_TCPM_MT6370 -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_DISCHARGE_TCPC -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE - -/* TCPC MT6370 */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ - -/* - * The Maximum input voltage is 13.5V, need another 5% tolerance. - * 12.85V * 1.05 = 13.5V - */ -#define PD_MAX_VOLTAGE_MV 12850 -#define CONFIG_USB_PD_PREFER_MV -#elif defined(VARIANT_KUKUI_CHARGER_ISL9238) -#define CONFIG_CHARGER_ISL9238C -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 /* BOARD_RS1 */ -#define CONFIG_CHARGER_SENSE_RESISTOR 10 /* BOARD_RS2 */ -#define CONFIG_CHARGER_OTG -#define CONFIG_CHARGE_RAMP_HW - -/* TCPC FUSB302 */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 160000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ - -/* b/2230219: 15V has better charging performance than 20V */ -#define PD_MAX_VOLTAGE_MV 15000 -#else -#error Must define a VARIANT_KUKUI_CHARGER -#endif /* VARIANT_KUKUI_CHARGER */ - -/* - * Variant pogo defines, if pick, VARIANT_KUKUI_POGO_KEYBOARD is mandatory - * VARIANT_KUKUI_POGO_KEYBOARD - * VARIANT_KUKUI_POGO_DOCK - */ -#ifdef VARIANT_KUKUI_POGO_DOCK -#ifndef VARIANT_KUKUI_POGO_KEYBOARD -#error VARIANT_KUKUI_POGO_KEYBOARD is mandatory if use dock -#endif /* !VARIANT_KUKUI_POGO_KEYBOARD */ -#undef CONFIG_DEDICATED_CHARGE_PORT_COUNT -#define CONFIG_DEDICATED_CHARGE_PORT_COUNT 1 -#define DEDICATED_CHARGE_PORT 1 -#endif /* VARIANT_KUKUI_POGO_DOCK */ - -#ifdef VARIANT_KUKUI_POGO_KEYBOARD -#define CONFIG_DETACHABLE_BASE -#define CONFIG_BASE_ATTACHED_SWITCH -#endif - -/* define this if the board is jacuzzi family */ -#ifdef VARIANT_KUKUI_JACUZZI -#define CONFIG_HOSTCMD_AP_SET_SKUID -/* - * IT81202 based boards are variant of jacuzzi and I/O expander isn't required - * on them. - */ -#if defined(VARIANT_KUKUI_EC_STM32F098) || defined(VARIANT_KUKUI_EC_STM32L431) -#define CONFIG_IO_EXPANDER -#define CONFIG_IO_EXPANDER_IT8801 -#define CONFIG_IO_EXPANDER_PORT_COUNT 1 -#define CONFIG_KEYBOARD_NOT_RAW - -#endif - -#define CONFIG_KEYBOARD_COL2_INVERTED - -#define CONFIG_GMR_TABLET_MODE -#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L -#define CONFIG_TABLET_MODE -#define CONFIG_TABLET_MODE_SWITCH - -#define PD_OPERATING_POWER_MW 30000 - -#define CONFIG_MKBP_HOST_EVENT_WAKEUP_MASK \ - (EC_HOST_EVENT_MASK(EC_HOST_EVENT_LID_OPEN) |\ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_POWER_BUTTON)) - -#else /* !VARIANT_KUKUI_JACUZZI */ - -#define CONFIG_MKBP_HOST_EVENT_WAKEUP_MASK \ - (EC_HOST_EVENT_MASK(EC_HOST_EVENT_LID_OPEN) |\ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_POWER_BUTTON) |\ - EC_HOST_EVENT_MASK(EC_HOST_EVENT_MODE_CHANGE)) - -#endif /* VARIANT_KUKUI_JACUZZI */ - -#if defined(SECTION_IS_RW) || defined(VARIANT_KUKUI_EC_IT81202) -#define CONFIG_POWER_SLEEP_FAILURE_DETECTION -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE -#endif - -/* - * Define this flag if board controls dp mux via gpio pins USB_C0_DP_OE_L and - * USB_C0_DP_POLARITY. - * - * board must provide function board_set_dp_mux_control(output_enable, polarity) - * - * #define VARIANT_KUKUI_DP_MUX_GPIO - */ - -/* Optional modules */ -#define CONFIG_ADC -#undef CONFIG_ADC_WATCHDOG -#define CONFIG_CHIPSET_MT8183 -#define CONFIG_CMD_ACCELS -#define CONFIG_EMULATED_SYSRQ -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER -#define CONFIG_I2C_VIRTUAL_BATTERY -#define CONFIG_I2C_PASSTHRU_RESTRICTED -#define CONFIG_LED_COMMON -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_POWER_COMMON -#define CONFIG_SPI -#define CONFIG_SWITCH - -#ifdef SECTION_IS_RO -#undef CONFIG_SYSTEM_UNLOCKED /* Disabled in RO to save space */ -#else -#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands for testing */ -#endif - -/* Bootblock */ -#ifdef SECTION_IS_RO -#define CONFIG_BOOTBLOCK - -#define EMMC_SPI_PORT 2 -#endif - -/* Optional features */ -#define CONFIG_BOARD_PRE_INIT -#define CONFIG_BUTTON_TRIGGERED_RECOVERY -#define CONFIG_CHARGER_ILIM_PIN_DISABLED -#define CONFIG_FORCE_CONSOLE_RESUME -#define CONFIG_HOST_COMMAND_STATUS -#define CONFIG_CMD_AP_RESET_LOG -#define CONFIG_PRESERVE_LOGS - -/* Required for FAFT */ -#define CONFIG_CMD_BUTTON -#define CONFIG_CMD_CHARGEN - -/* By default, set hcdebug to off */ -#undef CONFIG_HOSTCMD_DEBUG_MODE -#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF - -#define CONFIG_LTO -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_IGNORE_LID -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE -#define CONFIG_SOFTWARE_PANIC -#define CONFIG_VBOOT_HASH - -#define CONFIG_CHARGER -#define CONFIG_CHARGER_INPUT_CURRENT 512 -#define CONFIG_CHARGER_LIMIT_POWER_THRESH_BAT_PCT 2 -#define CONFIG_CHARGER_LIMIT_POWER_THRESH_CHG_MW 15000 -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_DISCHARGE_ON_AC_CUSTOM -#define CONFIG_USB_CHARGER - -/* Increase tx buffer size, as we'd like to stream EC log to AP. */ -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 4096 - -#define GPIO_LID_OPEN GPIO_HALL_INT_L - -#ifndef VARIANT_KUKUI_NO_SENSORS -#define CONFIG_ACCEL_FIFO -/* FIFO size is in power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) -#endif /* VARIANT_KUKUI_NO_SENSORS */ - -#ifndef VARIANT_KUKUI_TABLET_PWRBTN -#define POWERBTN_BOOT_DELAY 0 -#endif - -/* USB PD config */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_PORT_MAX_COUNT 1 -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_5V_EN_CUSTOM -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP -#define CONFIG_USB_PD_COMM_LOCKED - -#define CONFIG_BATTERY_CRITICAL_SHUTDOWN_CUT_OFF -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_PRESENT_CUSTOM -#define CONFIG_BATTERY_REVIVE_DISCONNECT - -#define PD_MAX_POWER_MW ((PD_MAX_VOLTAGE_MV * PD_MAX_CURRENT_MA) / 1000) -#ifdef BOARD_KODAMA -#define PD_MAX_CURRENT_MA 2000 -#else -#define PD_MAX_CURRENT_MA 3000 -#endif - -/* Optional for testing */ -#undef CONFIG_PECI -#undef CONFIG_PSTORE - -#define CONFIG_TASK_PROFILING -#define CONFIG_MKBP_USE_GPIO - -/* - * Variant EC defines. Pick one: - * VARIANT_KUKUI_EC_STM32F098 - * VARIANT_KUKUI_EC_IT81202 - * VARIANT_KUKUI_EC_STM32L431 - */ -#if defined(VARIANT_KUKUI_EC_STM32F098) || defined(VARIANT_KUKUI_EC_STM32L431) -/* Timer selection */ -#define TIM_CLOCK32 2 -#define TIM_WATCHDOG 7 - -/* 48 MHz SYSCLK clock frequency */ -#ifdef VARIANT_KUKUI_EC_STM32L431 -#define CPU_CLOCK 80000000 -#else -#define CPU_CLOCK 48000000 -#endif - -#undef CONFIG_HIBERNATE -#define CONFIG_SPI_CONTROLLER -#define CONFIG_STM_HWTIMER32 -#define CONFIG_WATCHDOG_HELP -#undef CONFIG_UART_CONSOLE -#define CONFIG_UART_CONSOLE 1 -#define CONFIG_UART_RX_DMA - -/* This option is limited to TCPMv1 */ -#define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0 -/* STM32F098 based boards use TCPMv1 */ -#define CONFIG_USB_PD_TCPMV1 -#define CONFIG_USB_PD_VBUS_DETECT_TCPC - -/* Modules we want to exclude */ -#undef CONFIG_CMD_BATTFAKE -#undef CONFIG_CMD_FLASH -#undef CONFIG_CMD_FLASHINFO -#undef CONFIG_CMD_HASH -#undef CONFIG_CMD_MD -#undef CONFIG_CMD_POWERINDEBUG -#undef CONFIG_CMD_TIMERINFO - -/* save space at RO image */ -#ifdef SECTION_IS_RO -#undef CONFIG_CMD_ADC -#undef CONFIG_CMD_APTHROTTLE -#undef CONFIG_CMD_CRASH -#undef CONFIG_CMD_HCDEBUG -#undef CONFIG_CMD_IDLE_STATS -#undef CONFIG_CMD_MFALLOW -#undef CONFIG_CMD_MMAPINFO -#undef CONFIG_CMD_PWR_AVG -#undef CONFIG_CMD_REGULATOR -#undef CONFIG_CMD_RW -#undef CONFIG_CMD_SHMEM -#undef CONFIG_CMD_SLEEPMASK -#undef CONFIG_CMD_SLEEPMASK_SET -#undef CONFIG_CMD_SYSLOCK -#undef CONFIG_CMD_TYPEC -#undef CONFIG_HOSTCMD_FLASHPD -#undef CONFIG_HOSTCMD_RWHASHPD -#undef CONFIG_CONSOLE_CMDHELP - -#undef CONFIG_HOSTCMD_GET_UPTIME_INFO -#undef CONFIG_CMD_AP_RESET_LOG -#undef CONFIG_CMD_I2C_SCAN -#undef CONFIG_CMD_I2C_XFER - -/* free flash space */ -#undef CONFIG_USB_PD_DEBUG_LEVEL -#define CONFIG_USB_PD_DEBUG_LEVEL 0 -#undef CONFIG_USB_PD_LOGGING -#define CONFIG_COMMON_GPIO_SHORTNAMES -#define CONFIG_DEBUG_ASSERT_BRIEF -/* Exclude PD state names from RO image to save space */ -#undef CONFIG_USB_PD_TCPMV1_DEBUG -#endif -#elif defined(VARIANT_KUKUI_EC_IT81202) -#define CONFIG_IT83XX_HARD_RESET_BY_GPG1 -#define CONFIG_IT83XX_VCC_1P8V - -/* IT81202 based boards use TCPMv2 */ -#define CONFIG_USB_DRP_ACC_TRYSRC -#define CONFIG_USB_PD_DECODE_SOP -#define CONFIG_USB_PD_ITE_ACTIVE_PORT_COUNT 1 -#define CONFIG_USB_PD_TCPMV2 -#else -#error "Must define a VARIANT_KUKUI_EC_XXX!" -#endif - -#ifndef __ASSEMBLER__ -#ifdef VARIANT_KUKUI_DP_MUX_GPIO -void board_set_dp_mux_control(int output_enable, int polarity); -#endif /* VARIANT_KUKUI_DP_MUX_GPIO */ - -/* If POGO pin is providing power. */ -int kukui_pogo_extpower_present(void); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BASEBOARD_H */ |