diff options
Diffstat (limited to 'baseboard/octopus/baseboard.h')
| -rw-r--r-- | baseboard/octopus/baseboard.h | 322 |
1 files changed, 0 insertions, 322 deletions
diff --git a/baseboard/octopus/baseboard.h b/baseboard/octopus/baseboard.h deleted file mode 100644 index 8b05c30f4c..0000000000 --- a/baseboard/octopus/baseboard.h +++ /dev/null @@ -1,322 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Octopus board configuration */ - -#ifndef __CROS_EC_BASEBOARD_H -#define __CROS_EC_BASEBOARD_H - -/******************************************************************************* - * EC Config - */ - -/* - * By default, enable all console messages excepted HC, ACPI and event: - * The sensor stack is generating a lot of activity. - */ -#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC))) - -/* - * Variant EC defines. Pick one: - * VARIANT_OCTOPUS_EC_NPCX796FB - * VARIANT_OCTOPUS_EC_ITE8320 - */ -#if defined(VARIANT_OCTOPUS_EC_NPCX796FB) - /* NPCX7 config */ - #define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ - #define NPCX_TACH_SEL2 0 /* [0:GPIO40/73, 1:GPIO93/A6] as TACH */ - #define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ - - /* Internal SPI flash on NPCX7 */ - /* Flash is 1MB but reserve half for future use. */ - #define CONFIG_FLASH_SIZE_BYTES (512 * 1024) - - #define CONFIG_SPI_FLASH_REGS - #define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */ - - /* I2C Bus Configuration */ - #define I2C_PORT_BATTERY NPCX_I2C_PORT0_0 - #define I2C_PORT_TCPC0 NPCX_I2C_PORT1_0 - #define I2C_PORT_TCPC1 NPCX_I2C_PORT2_0 - #define I2C_PORT_EEPROM NPCX_I2C_PORT3_0 - #define I2C_PORT_CHARGER NPCX_I2C_PORT4_1 - #define I2C_PORT_SENSOR NPCX_I2C_PORT7_0 - #define I2C_ADDR_EEPROM_FLAGS 0x50 - - /* Enable PSL hibernate mode. */ - #define CONFIG_HIBERNATE_PSL - - /* EC variant determines USB-C variant */ - #define VARIANT_OCTOPUS_USBC_STANDALONE_TCPCS - - /* Allow the EC to enter deep sleep in S0 */ - #define CONFIG_LOW_POWER_S0 -#elif defined(VARIANT_OCTOPUS_EC_ITE8320) - /* IT83XX config */ - #define CONFIG_IT83XX_VCC_1P8V - /* I2C Bus Configuration */ - #define I2C_PORT_BATTERY IT83XX_I2C_CH_A /* Shared bus */ - #define I2C_PORT_CHARGER IT83XX_I2C_CH_A /* Shared bus */ - #define I2C_PORT_SENSOR IT83XX_I2C_CH_B - #define I2C_PORT_USBC0 IT83XX_I2C_CH_C - #define I2C_PORT_USBC1 IT83XX_I2C_CH_E - #define I2C_PORT_USB_MUX I2C_PORT_USBC0 /* For MUX driver */ - #define I2C_PORT_EEPROM IT83XX_I2C_CH_F - #define I2C_ADDR_EEPROM_FLAGS 0x50 - #define CONFIG_USB_PD_ITE_ACTIVE_PORT_COUNT 2 - - /* EC variant determines USB-C variant */ - #define VARIANT_OCTOPUS_USBC_ITE_EC_TCPCS -#else - #error Must define a VARIANT_OCTOPUS_EC -#endif /* VARIANT_OCTOPUS_EC */ - -/* Common EC defines */ -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER -#define CONFIG_I2C_BUS_MAY_BE_UNPOWERED -#define CONFIG_VBOOT_HASH -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 -#define CONFIG_CRC8 -#define CONFIG_CBI_EEPROM -#define CONFIG_BOARD_VERSION_CBI -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_DPTF -#define CONFIG_DO_NOT_INCLUDE_RV32I_PANIC_DATA -#define CONFIG_BOARD_HAS_RTC_RESET -#define CONFIG_LED_ONOFF_STATES -#define CONFIG_CMD_CHARGEN - -/* Port80 -- allow larger buffer for port80 messages */ -#undef CONFIG_PORT80_HISTORY_LEN -#define CONFIG_PORT80_HISTORY_LEN 256 - -/* - * We don't need CONFIG_BACKLIGHT_LID since hardware AND's LID_OPEN and AP - * signals with EC backlight enable signal. - */ - -/******************************************************************************* - * Battery/Charger/Power Config - */ - -/* - * Variant charger defines. Pick one: - * VARIANT_OCTOPUS_CHARGER_ISL9238 - * VARIANT_OCTOPUS_CHARGER_BQ25703 - */ -#if defined(VARIANT_OCTOPUS_CHARGER_ISL9238) - #define CONFIG_CHARGER_ISL9238 - #define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 - /* - * ISL923x driver sets "Adapter insertion to Switching Debounce" - * CONTROL2 REG 0x3DH <Bit 11> to 1 which is 150 ms - */ - #undef CONFIG_EXTPOWER_DEBOUNCE_MS - #define CONFIG_EXTPOWER_DEBOUNCE_MS 200 -#elif defined(VARIANT_OCTOPUS_CHARGER_BQ25703) - #define CONFIG_CHARGER_BQ25703 - #define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 - /* - * From BQ25703: CHRG_OK is HIGH after 50ms deglitch time. - */ - #undef CONFIG_EXTPOWER_DEBOUNCE_MS - #define CONFIG_EXTPOWER_DEBOUNCE_MS 50 -#elif defined(CONFIG_CHARGER_RUNTIME_CONFIG) - #define CONFIG_CHARGER_ISL9238 - #define CONFIG_CHARGER_BQ25710 - #define CONFIG_CHARGER_SENSE_RESISTOR_AC_ISL9238 20 - #define CONFIG_CHARGER_SENSE_RESISTOR_AC_BQ25710 10 - - #undef CONFIG_EXTPOWER_DEBOUNCE_MS - #define CONFIG_EXTPOWER_DEBOUNCE_MS 200 -#else - #error Must define a VARIANT_OCTOPUS_CHARGER -#endif /* VARIANT_OCTOPUS_CHARGER */ - -/* Common charger defines */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGE_RAMP_HW -#define CONFIG_CHARGER -#define CONFIG_CHARGER_INPUT_CURRENT 512 /* Allow low-current USB charging */ -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_USB_CHARGER - -/* Common battery defines */ -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION" -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_PRESENT_GPIO GPIO_EC_BATT_PRES_L -#define CONFIG_BATTERY_REVIVE_DISCONNECT -#define CONFIG_BATTERY_SMART - -/******************************************************************************* - * USB-C Configs - * Automatically defined by VARIANT_OCTOPUS_EC_ variant. - */ - - /* - * Variant USBC defines. Pick one: - * VARIANT_OCTOPUS_USBC_STANDALONE_TCPCS - * VARIANT_OCTOPUS_USBC_ITE_EC_TCPCS (requires) - */ -#if defined(VARIANT_OCTOPUS_USBC_STANDALONE_TCPCS) - #define CONFIG_USB_PD_TCPC_LOW_POWER - #define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#if !defined(VARIANT_OCTOPUS_TCPC_0_PS8751) - #define CONFIG_USB_PD_TCPM_ANX7447 /* C0 TCPC: ANX7447QN */ -#endif - #define CONFIG_USB_PD_TCPM_PS8751 /* C1 TCPC: PS8751 */ - #define CONFIG_USB_PD_VBUS_DETECT_TCPC - #define CONFIG_USBC_PPC_NX20P3483 -#elif defined(VARIANT_OCTOPUS_USBC_ITE_EC_TCPCS) - #undef CONFIG_USB_PD_TCPC_LOW_POWER - #undef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE - #define CONFIG_USB_PD_VBUS_DETECT_PPC - #define CONFIG_USB_PD_TCPM_ITE_ON_CHIP /* C0 & C1 TCPC: ITE EC */ - #define CONFIG_USB_MUX_IT5205 /* C0 MUX: IT5205 */ - #define CONFIG_USB_PD_TCPM_PS8751 /* C1 Mux: PS8751 */ - #define CONFIG_USB_PD_TCPM_PS8751_CUSTOM_MUX_DRIVER - #define CONFIG_USBC_PPC_SN5S330 /* C0 & C1 PPC: each SN5S330 */ - #define CONFIG_USBC_PPC_VCONN - #define CONFIG_USBC_PPC_DEDICATED_INT -#else - #error Must define a VARIANT_OCTOPUS_USBC -#endif /* VARIANT_OCTOPUS_USBC */ - -/* Common USB-C defines */ -#define USB_PD_PORT_TCPC_0 0 -#define USB_PD_PORT_TCPC_1 1 -#define CONFIG_USB_PID 0x5046 - -#define CONFIG_USB_DRP_ACC_TRYSRC -#define CONFIG_USB_PD_DECODE_SOP -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_TCPMV2 -#define CONFIG_USB_PD_3A_PORTS 0 -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_COMM_LOCKED -#define CONFIG_USB_PD_DISCHARGE_PPC -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP -#define CONFIG_USB_PD_VBUS_MEASURE_ADC_EACH_PORT -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_BC12_DETECT_MAX14637 -#undef CONFIG_BC12_MAX14637_DELAY_FROM_OFF_TO_ON_MS -#define CONFIG_BC12_MAX14637_DELAY_FROM_OFF_TO_ON_MS 100 -#define CONFIG_HOSTCMD_PD_CONTROL -#define CONFIG_CMD_PPC_DUMP - -/* TODO(b/76218141): Use correct PD delay values */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ - -/* TODO(b/76218141): Use correct PD power values */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 45000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 - -/******************************************************************************* - * USB-A Configs - */ - -/* Common USB-A defines */ -#define USB_PORT_COUNT 2 -#define CONFIG_USB_PORT_POWER_SMART -#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY -#define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP -#define CONFIG_USB_PORT_POWER_SMART_INVERTED -#define GPIO_USB1_ILIM_SEL GPIO_USB_A0_CHARGE_EN_L -#define GPIO_USB2_ILIM_SEL GPIO_USB_A1_CHARGE_EN_L - -/******************************************************************************* - * SoC / PCH Config - */ - - /* Common SoC / PCH defines */ -#define CONFIG_CHIPSET_GEMINILAKE -#define CONFIG_CHIPSET_RESET_HOOK -#define CONFIG_HOSTCMD_ESPI -/* TODO(b/74123961): Enable Virtual Wires after bringup */ -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_S0IX -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_POWER_PP5000_CONTROL -#define CONFIG_EXTPOWER_GPIO - -/******************************************************************************* - * Keyboard Config - */ - -/* Common Keyboard Defines */ -#define CONFIG_CMD_KEYBOARD - -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2 -#undef CONFIG_KEYBOARD_VIVALDI - -/******************************************************************************* - * Sensor Config - */ - -/* Common Sensor Defines */ -#define CONFIG_TABLET_MODE -#define CONFIG_GMR_TABLET_MODE -#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L -/* - * Slew rate on the PP1800_SENSOR load switch requires a short delay on startup. - */ -#undef CONFIG_MOTION_SENSE_RESUME_DELAY_US -#define CONFIG_MOTION_SENSE_RESUME_DELAY_US (10 * MSEC) - -#ifndef VARIANT_OCTOPUS_NO_SENSORS -/* - * Interrupt and fifo are only used for base accelerometer - * and the lid sensor is polled real-time (in forced mode). - */ -#define CONFIG_ACCEL_INTERRUPTS -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* Power of 2 - Too large of a fifo causes too much timestamp jitter */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) -#endif /* VARIANT_OCTOPUS_NO_SENSORS */ - -/* - * Sensor stack in EC/Kernel depends on a hardware interrupt pin from EC->AP, so - * do not define CONFIG_MKBP_USE_HOST_EVENT since all octopus boards use - * hardware pin to send interrupt from EC -> AP (except casta). - */ -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_USE_GPIO - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" - -/* Forward declare common (within octopus) board-specific functions */ -void board_reset_pd_mcu(void); - -#ifdef VARIANT_OCTOPUS_USBC_STANDALONE_TCPCS -void tcpc_alert_event(enum gpio_signal signal); -#endif - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BASEBOARD_H */ |