diff options
Diffstat (limited to 'baseboard/volteer/baseboard.h')
| -rw-r--r-- | baseboard/volteer/baseboard.h | 285 |
1 files changed, 0 insertions, 285 deletions
diff --git a/baseboard/volteer/baseboard.h b/baseboard/volteer/baseboard.h deleted file mode 100644 index 38a464813a..0000000000 --- a/baseboard/volteer/baseboard.h +++ /dev/null @@ -1,285 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Volteer baseboard configuration */ - -#ifndef __CROS_EC_BASEBOARD_H -#define __CROS_EC_BASEBOARD_H - -#include <stdbool.h> - -/* - * By default, enable all console messages excepted HC - */ -#define CC_DEFAULT (CC_ALL & ~(BIT(CC_HOSTCMD))) - -/* NPCX7 config */ -#define NPCX7_PWM1_SEL 1 /* GPIO C2 is used as PWM1. */ -#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ -/* Internal SPI flash on NPCX796FC is 512 kB */ -#define CONFIG_FLASH_SIZE_BYTES (512 * 1024) -#define CONFIG_SPI_FLASH_REGS -#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */ - -/* Allow objects to be linked into a flash resident section */ -#define CONFIG_CHIP_INIT_ROM_REGION - -/* EC Defines */ -#define CONFIG_LTO -#define CONFIG_BOARD_VERSION_CBI -#define CONFIG_CRC8 -#define CONFIG_CBI_EEPROM -#define CONFIG_DPTF -#define CONFIG_FPU -#define CONFIG_HIBERNATE_PSL -#define CONFIG_PWM -#define CONFIG_VBOOT_HASH -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 -#define CONFIG_VOLUME_BUTTONS -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_BOARD_RESET_AFTER_POWER_ON - -/* Host communication */ -#define CONFIG_HOSTCMD_ESPI -#define CONFIG_HOSTCMD_ESPI_VW_SLP_S4 - -/* Chipset config */ -#define CONFIG_CHIPSET_TIGERLAKE -#define CONFIG_CHIPSET_PP3300_RAIL_FIRST -#define CONFIG_CHIPSET_SLP_S3_L_OVERRIDE -#define CONFIG_CHIPSET_X86_RSMRST_DELAY -#define CONFIG_CHIPSET_RESET_HOOK -#define CONFIG_CPU_PROCHOT_ACTIVE_LOW -#define CONFIG_EXTPOWER_GPIO -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_S0IX -#define CONFIG_POWER_SLEEP_FAILURE_DETECTION -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE -#define CONFIG_BOARD_HAS_RTC_RESET - -/* Common Keyboard Defines */ -#define CONFIG_CMD_KEYBOARD - -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_KEYPAD -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2 -#define CONFIG_PWM_KBLIGHT - -/* Sensors */ -#define CONFIG_TABLET_MODE -#define CONFIG_GMR_TABLET_MODE - -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_USE_GPIO -#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT -#define CONFIG_ACCEL_INTERRUPTS - -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is in power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) - -/* Sensor console commands */ -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO - -/* Thermal features */ -#define CONFIG_FANS FAN_CH_COUNT -#define CONFIG_TEMP_SENSOR -#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_PG_EC_DSW_PWROK -#define CONFIG_THERMISTOR -#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B -#define CONFIG_THROTTLE_AP -#define CONFIG_CHIPSET_CAN_THROTTLE - -/* Common charger defines */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGER -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 512 - -/* - * Hardware based charge ramp is broken in the ISL9241 (b/169350714). - */ -#define CONFIG_CHARGE_RAMP_SW -#define CONFIG_CHARGER_ISL9241 -/* Setting ISL9241 Register Control1 switching frequency to 724kHz. */ -#define CONFIG_ISL9241_SWITCHING_FREQ ISL9241_CONTROL1_SWITCHING_FREQ_724KHZ - -#define CONFIG_USB_CHARGER -#define CONFIG_BC12_DETECT_PI3USB9201 - -/* - * Don't allow the system to boot to S0 when the battery is low and unable to - * communicate on locked systems (which haven't PD negotiated) - */ -#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON_WITH_BATT 15000 -#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 15001 - -/* Common battery defines */ -#define CONFIG_BATTERY_SMART -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_PRESENT_CUSTOM -#define CONFIG_BATTERY_HW_PRESENT_CUSTOM -#define CONFIG_BATTERY_REVIVE_DISCONNECT - -/* Common LED defines */ -#define CONFIG_LED_COMMON - -/* EDP back-light control defines */ -#define CONFIG_BACKLIGHT_LID -#define GPIO_ENABLE_BACKLIGHT GPIO_EC_EDP_BL_EN - -/* USB Type C and USB PD defines */ -/* Enable the new USB-C PD stack */ -#define CONFIG_USB_PD_TCPMV2 -#define CONFIG_USB_DRP_ACC_TRYSRC -#define CONFIG_USB_PD_REV30 - -/* - * TODO(b/158572770): TCPMv2: Conserve flash space - * Add these console commands as flash space permits. - */ -#undef CONFIG_CMD_HCDEBUG -#undef CONFIG_CMD_ACCELS -#undef CONFIG_CMD_ACCEL_INFO -#undef CONFIG_CMD_ACCELSPOOF -#undef CONFIG_CMD_PPC_DUMP - -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_ALT_MODE_UFP -#define CONFIG_USB_PD_DISCHARGE_PPC -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_TCPC_RUNTIME_CONFIG -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TCPM_RT1715 -#define CONFIG_USB_PD_TCPM_TUSB422 /* USBC port C0 */ -#define CONFIG_USB_PD_TCPM_PS8815 /* USBC port USB3 DB */ -#define CONFIG_USB_PD_TCPM_PS8815_FORCE_DID -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_HOSTCMD_PD_CONTROL /* Needed for TCPC FW update */ -#define CONFIG_CMD_USB_PD_PE - -/* - * Because of the CSE Lite, an extra cold AP reset is needed, and older cr50 - * firmware will not be able to detect it because of updated cr50 pin straps. - * Therefore, the AP will require the EC to reset it so that the proper reset - * signal will be read and verstage can execute again. - */ -#define CONFIG_CMD_AP_RESET_LOG -#define CONFIG_HOSTCMD_AP_RESET - -/* - * The PS8815 TCPC was found to require a 50ms delay to consistently work - * with non-PD chargers. Override the default low-power mode exit delay. - */ -#undef CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE -#define CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE (50*MSEC) - -/* Enable USB3.2 DRD */ -#define CONFIG_USB_PD_USB32_DRD - -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_PD_VBUS_DETECT_TCPC - -#define CONFIG_USB_MUX_RUNTIME_CONFIG - -#define CONFIG_USBC_PPC -/* Note - SN5S330 support automatically adds - * CONFIG_USBC_PPC_POLARITY - * CONFIG_USBC_PPC_SBU - * CONFIG_USBC_PPC_VCONN - */ -#define CONFIG_USBC_PPC_DEDICATED_INT - -#define CONFIG_USBC_SS_MUX -#define CONFIG_USB_MUX_VIRTUAL - -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP - -/* Enabling SOP* communication */ -#define CONFIG_CMD_USB_PD_CABLE -#define CONFIG_USB_PD_DECODE_SOP - -/* UART COMMAND */ -#define CONFIG_CMD_CHARGEN - -/* - * USB ID - * This is allocated specifically for Volteer - * http://google3/hardware/standards/usb/ - */ -#define CONFIG_USB_PID 0x503E -/* Device version of product. */ -#define CONFIG_USB_BCD_DEV 0x0000 - -/* Retimer */ -#define CONFIG_USBC_RETIMER_INTEL_BB -#define CONFIG_USBC_RETIMER_INTEL_BB_RUNTIME_CONFIG -#define CONFIG_USBC_RETIMER_FW_UPDATE - -/* Enable volume button command in EC console */ -#define CONFIG_CMD_BUTTON - -/* Enable volume button in ectool */ -#define CONFIG_HOSTCMD_BUTTON - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "common.h" -#include "baseboard_usbc_config.h" -#include "cbi.h" - -enum adc_channel { - ADC_TEMP_SENSOR_1_CHARGER, - ADC_TEMP_SENSOR_2_PP3300_REGULATOR, - ADC_TEMP_SENSOR_3_DDR_SOC, - ADC_TEMP_SENSOR_4_FAN, - ADC_CH_COUNT -}; - -enum fan_channel { - FAN_CH_0 = 0, - /* Number of FAN channels */ - FAN_CH_COUNT, -}; - -enum mft_channel { - MFT_CH_0 = 0, - /* Number of MFT channels */ - MFT_CH_COUNT, -}; - -enum temp_sensor_id { - TEMP_SENSOR_1_CHARGER, - TEMP_SENSOR_2_PP3300_REGULATOR, - TEMP_SENSOR_3_DDR_SOC, - TEMP_SENSOR_4_FAN, - TEMP_SENSOR_COUNT -}; - -/* - * Check battery disconnect state. - * This function will return if battery is initialized or not. - * @return true - initialized. false - not. - */ -__override_proto bool board_battery_is_initialized(void); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BASEBOARD_H */ |