diff options
Diffstat (limited to 'baseboard/zork/baseboard.h')
| -rw-r--r-- | baseboard/zork/baseboard.h | 368 |
1 files changed, 0 insertions, 368 deletions
diff --git a/baseboard/zork/baseboard.h b/baseboard/zork/baseboard.h deleted file mode 100644 index d84ebbcef8..0000000000 --- a/baseboard/zork/baseboard.h +++ /dev/null @@ -1,368 +0,0 @@ -/* Copyright 2019 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Zork baseboard configuration */ - -#ifndef __CROS_EC_BASEBOARD_H -#define __CROS_EC_BASEBOARD_H - -#if (defined(VARIANT_ZORK_TREMBYLE) \ - + defined(VARIANT_ZORK_DALBOZ)) != 1 -#error Must choose VARIANT_ZORK_TREMBYLE or VARIANT_ZORK_DALBOZ -#endif - -/* NPCX7 config */ -#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */ -#define NPCX_TACH_SEL2 0 /* No tach. */ -#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */ - -/* Internal SPI flash on NPCX7 */ -#define CONFIG_FLASH_SIZE_BYTES (512 * 1024) -#define CONFIG_SPI_FLASH_REGS -#define CONFIG_SPI_FLASH_W25Q40 /* Internal SPI flash type. */ - -#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_HOSTCMD) | CC_MASK(CC_LPC))) - -/* - * Enable 1 slot of secure temporary storage to support - * suspend/resume with read/write memory training. - */ -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 - -#define CONFIG_ADC -#define CONFIG_BACKLIGHT_LID -#define CONFIG_BACKLIGHT_LID_ACTIVE_LOW -#define CONFIG_CMD_AP_RESET_LOG -#define CONFIG_CPU_PROCHOT_ACTIVE_LOW -#define CONFIG_HIBERNATE_PSL -#define CONFIG_HOSTCMD_ESPI -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER -#define CONFIG_I2C_UPDATE_IF_CHANGED -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_LTO -#define CONFIG_PWM -#define CONFIG_PWM_KBLIGHT -#define CONFIG_TEMP_SENSOR -#define CONFIG_THERMISTOR_NCP15WB -#define CONFIG_VBOOT_EFS2 -#define CONFIG_VBOOT_HASH -#define CONFIG_VOLUME_BUTTONS - -/* CBI EEPROM for board version and SKU ID */ -#define CONFIG_CBI_EEPROM -#define CONFIG_BOARD_VERSION_CBI -#define CONFIG_CRC8 - -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_REVIVE_DISCONNECT -#define CONFIG_BATTERY_SMART -/* - * Enable support for battery hostcmd, supporting longer strings. - * - * Vilboz battery options' model names vary in the 8th character, which is - * truncated in the memory mapped battery info; differentiating them requires - * support for EC_CMD_BATTERY_GET_STATIC version 1. - */ -#define CONFIG_BATTERY_V2 -#define CONFIG_BATTERY_COUNT 1 -#define CONFIG_HOSTCMD_BATTERY_V2 - -#define CONFIG_BC12_DETECT_PI3USB9201 - -#define CONFIG_CHARGER -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 512 -#define CONFIG_CHARGER_ISL9241 -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 -/* - * We would prefer to use CONFIG_CHARGE_RAMP_HW to enable legacy BC1.2 charging - * but that feature of ISL9241 is broken (b/160287056) so we have to use - * CONFIG_CHARGE_RAMP_SW instead. - */ -#define CONFIG_CHARGE_RAMP_SW - -#define CONFIG_CHIPSET_STONEY -#define CONFIG_CHIPSET_CAN_THROTTLE -#define CONFIG_CHIPSET_RESET_HOOK - -#undef CONFIG_EXTPOWER_DEBOUNCE_MS -#define CONFIG_EXTPOWER_DEBOUNCE_MS 200 -#define CONFIG_EXTPOWER_GPIO -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_POWER_BUTTON_TO_PCH_CUSTOM -#define CONFIG_THROTTLE_AP - -#ifdef VARIANT_ZORK_TREMBYLE - #define CONFIG_FANS FAN_CH_COUNT - #undef CONFIG_FAN_INIT_SPEED - #define CONFIG_FAN_INIT_SPEED 50 -#endif - -#define CONFIG_LED_COMMON -#define CONFIG_CMD_LEDTEST -#define CONFIG_LED_ONOFF_STATES - -/* - * On power-on, H1 releases the EC from reset but then quickly asserts and - * releases the reset a second time. This means the EC sees 2 resets: - * (1) power-on reset, (2) reset-pin reset. This config will - * allow the second reset to be treated as a power-on. - */ -#define CONFIG_BOARD_RESET_AFTER_POWER_ON - -#define CONFIG_IO_EXPANDER -#define CONFIG_IO_EXPANDER_NCT38XX - - -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#undef CONFIG_KEYBOARD_VIVALDI - -/* - * USB ID - * - * This is allocated specifically for Zork - * http://google3/hardware/standards/usb/ - */ -#define CONFIG_USB_PID 0x5040 - -#define CONFIG_USB_PD_REV30 - -/* Enable the TCPMv2 PD stack */ -#define CONFIG_USB_PD_TCPMV2 - -#ifndef CONFIG_USB_PD_TCPMV2 - #define CONFIG_USB_PD_TCPMV1 -#else - #define CONFIG_USB_PD_DECODE_SOP - #define CONFIG_USB_DRP_ACC_TRYSRC - - /* Enable TCPMv2 Fast Role Swap */ - /* Turn off until FRSwap is working */ - #undef CONFIG_USB_PD_FRS_TCPC -#endif - -#define CONFIG_HOSTCMD_PD_CONTROL -#define CONFIG_CMD_TCPC_DUMP -#define CONFIG_USB_CHARGER -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_COMM_LOCKED -#define CONFIG_USB_PD_DISCHARGE_TCPC -#define CONFIG_USB_PD_DP_HPD_GPIO -#ifdef VARIANT_ZORK_TREMBYLE -/* - * Use a custom HPD function that supports HPD on IO expander. - * TODO(b/165622386) remove this when HPD is on EC GPIO. - */ -# define CONFIG_USB_PD_DP_HPD_GPIO_CUSTOM -#endif -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_TCPM_MUX -#define CONFIG_USB_PD_TCPM_NCT38XX -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_PD_VBUS_DETECT_TCPC -#define CONFIG_USBC_PPC -#define CONFIG_USBC_PPC_SBU -#define CONFIG_USBC_PPC_AOZ1380 -#define CONFIG_USBC_RETIMER_PI3HDX1204 -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_SS_MUX_DFP_ONLY -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP -#define CONFIG_USB_MUX_AMD_FP5 - -#if defined(VARIANT_ZORK_TREMBYLE) - #define CONFIG_USB_PD_PORT_MAX_COUNT 2 - #define CONFIG_USBC_PPC_NX20P3483 - #define CONFIG_USBC_RETIMER_PS8802 - #define CONFIG_USBC_RETIMER_PS8818 - #define CONFIG_IO_EXPANDER_PORT_COUNT USBC_PORT_COUNT - #define CONFIG_USB_MUX_RUNTIME_CONFIG - /* USB-A config */ - #define GPIO_USB1_ILIM_SEL IOEX_USB_A0_CHARGE_EN_L - #define GPIO_USB2_ILIM_SEL IOEX_USB_A1_CHARGE_EN_DB_L - /* PS8818 RX Input Termination - default value */ - #define ZORK_PS8818_RX_INPUT_TERM PS8818_RX_INPUT_TERM_112_OHM -#elif defined(VARIANT_ZORK_DALBOZ) - #define CONFIG_IO_EXPANDER_PORT_COUNT IOEX_PORT_COUNT -#endif - -/* USB-A config */ -#define USB_PORT_COUNT USBA_PORT_COUNT -#define CONFIG_USB_PORT_POWER_SMART -#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY -#define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP -#define CONFIG_USB_PORT_POWER_SMART_INVERTED - -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ - -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 65000 -#define PD_MAX_CURRENT_MA 3250 -#define PD_MAX_VOLTAGE_MV 20000 - -/* Round up 3250 max current to multiple of 128mA for ISL9241 AC prochot. */ -#define ZORK_AC_PROCHOT_CURRENT_MA 3328 - -/* - * EC will boot AP to depthcharge if: (BAT >= 4%) || (AC >= 50W) - * CONFIG_CHARGER_LIMIT_* is not set, so there is no additional restriction on - * Depthcharge to boot OS. - */ -#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 50000 - -/* Increase length of history buffer for port80 messages. */ -#undef CONFIG_PORT80_HISTORY_LEN -#define CONFIG_PORT80_HISTORY_LEN 256 - -/* Increase console output buffer since we have the RAM available. */ -#undef CONFIG_UART_TX_BUF_SIZE -#define CONFIG_UART_TX_BUF_SIZE 4096 - -#define I2C_PORT_TCPC0 NPCX_I2C_PORT0_0 -#define I2C_PORT_USBA0 NPCX_I2C_PORT0_0 -#define I2C_PORT_TCPC1 NPCX_I2C_PORT1_0 -#define I2C_PORT_USBA1 NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_AP_MUX NPCX_I2C_PORT3_0 -#define I2C_PORT_THERMAL_AP NPCX_I2C_PORT4_1 -#define I2C_PORT_SENSOR NPCX_I2C_PORT5_0 -#define I2C_PORT_ACCEL I2C_PORT_SENSOR -#define I2C_PORT_EEPROM I2C_PORT_SENSOR -#define I2C_PORT_AP_AUDIO NPCX_I2C_PORT6_1 - -#if defined(VARIANT_ZORK_TREMBYLE) - #define CONFIG_CHARGER_RUNTIME_CONFIG - #define I2C_PORT_BATTERY NPCX_I2C_PORT2_0 - #define I2C_PORT_CHARGER_V0 NPCX_I2C_PORT2_0 - #define I2C_PORT_CHARGER_V1 NPCX_I2C_PORT4_1 - #define I2C_PORT_AP_HDMI NPCX_I2C_PORT7_0 -#elif defined(VARIANT_ZORK_DALBOZ) - #define I2C_PORT_BATTERY_V0 NPCX_I2C_PORT2_0 - #define I2C_PORT_BATTERY_V1 NPCX_I2C_PORT7_0 - #define I2C_PORT_CHARGER NPCX_I2C_PORT2_0 -#endif - -#define I2C_ADDR_EEPROM_FLAGS 0x50 - -#define CONFIG_MKBP_EVENT -/* Host event is required to wake from sleep */ -#define CONFIG_MKBP_USE_GPIO_AND_HOST_EVENT -/* Required to enable runtime configuration */ -#define CONFIG_MKBP_EVENT_WAKEUP_MASK (BIT(EC_MKBP_EVENT_DP_ALT_MODE_ENTERED)) - -/* Sensors */ -#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT - -/* Thermal */ -#define CONFIG_TEMP_SENSOR_SB_TSI - -#ifdef HAS_TASK_MOTIONSENSE -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is a power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -/* Depends on how fast the AP boots and typical ODRs. */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) -#endif - -/* Audio */ -#define CONFIG_AUDIO_CODEC -#define CONFIG_AUDIO_CODEC_DMIC -#define CONFIG_AUDIO_CODEC_I2S_RX - -/* CLI COMMAND */ -#define CONFIG_CMD_CHARGEN - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "math_util.h" -#include "registers.h" - -enum power_signal { - X86_SLP_S3_N, - X86_SLP_S5_N, - X86_S0_PGOOD, - X86_S5_PGOOD, - POWER_SIGNAL_COUNT -}; - -enum fan_channel { - FAN_CH_0 = 0, - /* Number of FAN channels */ - FAN_CH_COUNT, -}; - -#ifdef VARIANT_ZORK_TREMBYLE -enum usbc_port { - USBC_PORT_C0 = 0, - USBC_PORT_C1, - USBC_PORT_COUNT -}; -#endif - -enum sensor_id { - LID_ACCEL, - BASE_ACCEL, - BASE_GYRO, - SENSOR_COUNT, -}; - -/* - * Matrix to rotate accelerators into the standard reference frame. The default - * is the identity which is correct for the reference design. Variations of - * Zork may need to change it for manufacturability. - * For the lid: - * +x to the right - * +y up - * +z out of the page - * - * The principle axes of the body are aligned with the lid when the lid is in - * the 180 degree position (open, flat). - * - * Boards within the Zork family may need to modify this definition at - * board_init() time. - */ -extern mat33_fp_t zork_base_standard_ref; - -extern const struct thermistor_info thermistor_info; - -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK (1 << LID_ACCEL) - -void mst_hpd_interrupt(enum ioex_signal signal); -void sbu_fault_interrupt(enum ioex_signal signal); - -#ifdef VARIANT_ZORK_TREMBYLE -void board_reset_pd_mcu(void); - -/* Common definition for the USB PD interrupt handlers. */ -void tcpc_alert_event(enum gpio_signal signal); -void bc12_interrupt(enum gpio_signal signal); -__override_proto void ppc_interrupt(enum gpio_signal signal); -#endif - -void board_print_temps(void); - -/* GPIO or IOEX signal used to set IN_HPD on DB retimer. */ -extern int board_usbc1_retimer_inhpd; - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BASEBOARD_H */ |