diff options
Diffstat (limited to 'board/adlrvpp_mchp1727/gpio.inc')
| -rw-r--r-- | board/adlrvpp_mchp1727/gpio.inc | 262 |
1 files changed, 0 insertions, 262 deletions
diff --git a/board/adlrvpp_mchp1727/gpio.inc b/board/adlrvpp_mchp1727/gpio.inc deleted file mode 100644 index 1eea86462c..0000000000 --- a/board/adlrvpp_mchp1727/gpio.inc +++ /dev/null @@ -1,262 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Intel ADL-P-RVP-MCHP1727 board-specific configuration */ - -#include "baseboard/intelrvp/adlrvp_ioex_gpio.inc" -/* include common gpio.inc under chip/mchp/lfw/... */ -#include "chip/mchp/lfw/gpio.inc" - -/* Power sequencing interrupts */ -GPIO_INT(ALL_SYS_PWRGD, PIN(057), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(RSMRST_PWRGD, PIN(0221), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PCH_SLP_S0_N, PIN(0243), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(VCCPDSW_3P3, PIN(0201), GPIO_INT_BOTH, power_signal_interrupt) -/* TODO: GPIO_INT(VCCST_PWRGD_MECC, PIN(0207), GPIO_INT_BOTH, power_signal_interrupt) */ -GPIO_INT(PM_SLP_SUS_EC_N, PIN(0227), GPIO_INT_BOTH, power_signal_interrupt) -#ifndef CONFIG_HOSTCMD_ESPI_VW_SLP_S3 -GPIO_INT(PM_SLP_S3_N, PIN(0161), GPIO_INT_BOTH, power_signal_interrupt) -#else -GPIO(PM_SLP_S3_N, PIN(0161), GPIO_INPUT) -#endif -#ifndef CONFIG_HOSTCMD_ESPI_VW_SLP_S4 -GPIO_INT(PM_SLP_S4_N, PIN(0162), GPIO_INT_BOTH, power_signal_interrupt) -#else -GPIO(PM_SLP_S4_N, PIN(0162), GPIO_INPUT) -#endif - -/* Button interrupts */ -GPIO_INT(VOLUME_UP, PIN(036), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(VOL_DN_EC, PIN(0254), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(SMC_LID, PIN(0226), GPIO_INT_BOTH | GPIO_PULL_UP, lid_interrupt) -GPIO_INT(MECH_PWR_BTN_ODL, PIN(0115), GPIO_INT_BOTH, power_button_interrupt) - -/* DC / AC interrupts, DC Jack presence coming from +VADP_OUT */ -GPIO_INT(STD_ADP_PRSNT, PIN(043), GPIO_INT_BOTH, board_dc_jack_interrupt) /* DC_JACK_PRESENT */ -GPIO_INT(BC_ACOK, PIN(0156), GPIO_INT_BOTH, extpower_interrupt) /* AC Present */ - -/* Sensor interrupt */ -GPIO_INT(SLATE_MODE_INDICATION, PIN(0222), GPIO_INT_BOTH, gmr_tablet_switch_isr) - -/* Flash WP interrupt */ -GPIO_INT(EC_FLASH_WP_ODL, PIN(014), GPIO_INT_BOTH, switch_interrupt) - -/* Case Closed Debug Mode interrupt */ -GPIO_INT(CCD_MODE_ODL, PIN(0175), GPIO_INT_BOTH, board_connect_c0_sbu) - -/* UART0 RX interrupt, RX input wake event */ -GPIO_INT(UART0_RX, PIN(0105), GPIO_INT_BOTH_DSLEEP | GPIO_PULL_UP, uart_deepsleep_interrupt) - -/* USB-C interrupts */ -GPIO_INT(USBC_TCPC_ALRT_P0, PIN(0143), GPIO_INT_BOTH, tcpc_alert_event) -GPIO_INT(USBC_TCPC_PPC_ALRT_P0, PIN(0240), GPIO_INT_BOTH, ppc_interrupt) - -#if defined(HAS_TASK_PD_C1) -GPIO_INT(USBC_TCPC_ALRT_P1, PIN(0241), GPIO_INT_BOTH, tcpc_alert_event) -GPIO_INT(USBC_TCPC_PPC_ALRT_P1, PIN(0101), GPIO_INT_BOTH, ppc_interrupt) -#else -GPIO(USBC_TCPC_ALRT_P1, PIN(0241), GPIO_INPUT) -GPIO(USBC_TCPC_PPC_ALRT_P1, PIN(0101), GPIO_INPUT) -#endif - -#if defined(HAS_TASK_PD_C2) -/* w/o rework: USBC_TCPC_ALRT_P2 -> VCI_OVRD_IN */ -GPIO_INT(USBC_TCPC_ALRT_P2, PIN(0130), GPIO_INT_BOTH, tcpc_alert_event) -GPIO_INT(USBC_TCPC_PPC_ALRT_P2, PIN(0144), GPIO_INT_BOTH, ppc_interrupt) -#else -GPIO(USBC_TCPC_ALRT_P2, PIN(0130), GPIO_INPUT) -GPIO(USBC_TCPC_PPC_ALRT_P2, PIN(0144), GPIO_INPUT) -#endif - -#if defined(HAS_TASK_PD_C3) -GPIO_INT(USBC_TCPC_ALRT_P3, PIN(0242), GPIO_INT_BOTH, tcpc_alert_event) -GPIO_INT(USBC_TCPC_PPC_ALRT_P3, PIN(0142), GPIO_INT_BOTH, ppc_interrupt) -#else -GPIO(USBC_TCPC_ALRT_P3, PIN(0242), GPIO_INPUT) -GPIO(USBC_TCPC_PPC_ALRT_P3, PIN(0142), GPIO_INPUT) -#endif - -/* Host communication GPIOs */ -GPIO(SMC_WAKE_SCI_N_MECC, PIN(051), GPIO_ODR_HIGH) -GPIO(EC_PCH_MKBP_INT_ODL, PIN(0127), GPIO_ODR_HIGH) -#ifndef CONFIG_HOSTCMD_ESPI -GPIO(LPC_ESPI_RST_N, PIN(061), GPIO_INPUT) -GPIO(PLT_RST_L, PIN(052), GPIO_INPUT) /* PCH_PLTRST_L */ -#endif - -/* Prochot GPIO */ -GPIO(PROCHOT_EC_N, PIN(002), GPIO_INPUT) - -/* Power sequencing GPIOs */ -GPIO(SYS_RST_ODL, PIN(060), GPIO_ODR_HIGH) -GPIO(PM_RSMRST_N, PIN(054), GPIO_OUT_LOW) -GPIO(PM_PWRBTN_N, PIN(016), GPIO_ODR_HIGH) -/* w/o rework: EC_SPI_OE_MECC -> BGPO0 */ -GPIO(EC_SPI_OE_MECC, PIN(042), GPIO_OUT_LOW) -/* w/o rework: EC_DS3 -> VCI_OUT2 */ -GPIO(EC_DS3, PIN(025), GPIO_OUT_LOW) -UNIMPLEMENTED(EN_PP5000) - -/* PCH_PWROK_EC is an input, as it's driven by the Silego chip on RVP */ -GPIO(PCH_PWROK_EC, PIN(0106), GPIO_INPUT) -GPIO(SYS_PWROK, PIN(0202), GPIO_OUT_LOW) -GPIO(EC_DSW_PWROK, PIN(034), GPIO_OUT_LOW) - -/* H1 GPIOs */ -GPIO(EC_H1_PACKET_MODE, PIN(035), GPIO_OUT_LOW) -GPIO(EC_ENTERING_RW, PIN(0102), GPIO_OUT_LOW) - -/* Battery present */ -GPIO(BAT_DET, PIN(0206), GPIO_INPUT) - -/* EDP */ -GPIO(EDP_BKLT_EN_MECC, PIN(022), GPIO_OUT_HIGH) - -/* LED */ -GPIO(LED_1_L, PIN(0157), GPIO_OUT_HIGH) -GPIO(LED_2_L, PIN(0153), GPIO_OUT_HIGH) - -/* FAN control pins */ -GPIO(THERM_SEN_MECC, PIN(0141), GPIO_OUT_LOW) - -/* - * I2C pins should be configure as inputs until I2C module is - * initialized. This will avoid driving the lines unintentionally. - */ -GPIO(SMB_BS_CLK, PIN(004), GPIO_INPUT) /* I2C00_SCL */ -GPIO(SMB_BS_DATA, PIN(003), GPIO_INPUT) /* I2C00_SDA */ -GPIO(USBC_TCPC_I2C_CLK_P0, PIN(0140), GPIO_INPUT) /* I2C06_SCL */ -GPIO(USBC_TCPC_I2C_DATA_P0, PIN(0132), GPIO_INPUT) /* I2C06_SDA */ -GPIO(USBC_TCPC_I2C_CLK_P1, PIN(013), GPIO_INPUT) /* I2C07_SCL */ -GPIO(USBC_TCPC_I2C_DATA_P1, PIN(012), GPIO_INPUT) /* I2C07_SDA */ -GPIO(USBC_TCPC_I2C_CLK_P2, PIN(010), GPIO_INPUT) /* I2C03_SCL */ -GPIO(USBC_TCPC_I2C_DATA_P2, PIN(007), GPIO_INPUT) /* I2C03_SDA */ -GPIO(USBC_TCPC_I2C_CLK_P3, PIN(0155), GPIO_INPUT) /* I2C02_SCL */ -GPIO(USBC_TCPC_I2C_DATA_P3, PIN(0154), GPIO_INPUT) /* I2C02_SDA */ - -/* Unused pins */ -GPIO(SML1_CLK_MECC, PIN(0131), GPIO_INPUT) -GPIO(CPU_CAT_ERR_MECC, PIN(000), GPIO_INPUT) -GPIO(ESPI_ALERT0_N, PIN(063), GPIO_INPUT) -GPIO(BATT_DISABLE_EC, PIN(067), GPIO_INPUT) -/* Unused: GPIO(SLP_S0_CS_N, PIN(nVCI_IN0), GPIO_INPUT) */ -GPIO(CPU_C10_GATE_MECC, PIN(023), GPIO_INPUT) -GPIO(SMC_SDOWN_MECC, PIN(0255), GPIO_INPUT) -GPIO(STD_ADPT_CNTRL_GPIO, PIN(0244), GPIO_INPUT) -GPIO(SMC_ONOFF_N, PIN(0114), GPIO_INPUT) /* Power button interrupt without H1 */ -GPIO(SUSWARN, PIN(024), GPIO_INPUT) -GPIO(ME_G3_TO_M3_EC, PIN(033), GPIO_INPUT) - -/* Alternate pins for I2C */ -/* I2C pins alternate functions for ports 0, 2-3, 6-7 - * Configure I2C ports as I2C alternate function. - * If board does not use external pull-ups then change GPIO flags - * to enable internal pull-ups. - * I2C00_SDA = GPIO_0003(Bank=0, bit=3) Func1 - * I2C00_SCL = GPIO_0004(Bank=0, bit=4) Func1 - * I2C02_SDA = GPIO_0154(Bank=3, bit=12) Func1 - * I2C02_SCL = GPIO_0155(Bank=3, bit=13) Func1 - * I2C03_SDA = GPIO_0007(Bank=0, bit=7) Func1 - * I2C03_SDL = GPIO_0010(Bank=0, bit=8) Func1 - * I2C06_SDA = GPIO_0132(Bank=2, bit=26) Func1 - * I2C06_SCL = GPIO_0140(Bank=3, bit=0) Func1 - * I2C07_SDA = GPIO_0012(Bank=0, bit=10) Func1 - * I2C07_SDL = GPIO_0013(Bank=0, bit=11) Func1 - */ -ALTERNATE(PIN_MASK(0, 0x00000D98), 1, MODULE_I2C, GPIO_ODR_HIGH) -ALTERNATE(PIN_MASK(2, 0x04000000), 1, MODULE_I2C, GPIO_ODR_HIGH) -ALTERNATE(PIN_MASK(3, 0x00003001), 1, MODULE_I2C, GPIO_ODR_HIGH) - -/* Alternate pins for ADC */ -/* VR_TMP/V_1P05 - GPIO44, SKIN_THERM_IN_EC - GPIO43, AMBIENT_TEMP - GPIO42, DDR_TEMP/EC_5V - GPIO41 */ -/* ADC pins - * GPIO200/ADC00 = VR_TMP/V_1P05 - * GPIO203/ADC03 = AMBIENT_TEMP - * GPIO204/ADC04 = SKIN_THERM_IN_EC - * GPIO205/ADC05 = DDR_TEMP/EC_5V - * ADC00 = GPIO_0200(Bank=4, bit=0) Func1 - * ADC03 = GPIO_0203(Bank=4, bit=3) Func1 - * ADC04 = GPIO_0204(Bank=4, bit=4) Func1 - * ADC05 = GPIO_0205(Bank=4, bit=5) Func1 - */ -ALTERNATE(PIN_MASK(4, 0x0039), 1, MODULE_ADC, GPIO_ANALOG) - -/* - * Alternate pins for RPM-FAN control - * - * GPIO050/GTACH0 = CPU_TACHO_FAN - * GPIO053/GPWM0 = CPU_PWM_FAN - * GTACH0 = GPIO_050(Bank=1, bit=8) Func2 - * GPWM0 = GPIO_053(Bank=1, bit=11) Func3 - */ -ALTERNATE(PIN_MASK(1, 0x0100), 2, MODULE_PWM, GPIO_FLAG_NONE) -ALTERNATE(PIN_MASK(1, 0x0800), 3, MODULE_PWM, GPIO_FLAG_NONE) - -/* Keyboard pins */ -#define GPIO_KB_INPUT (GPIO_INPUT | GPIO_PULL_UP) -#define GPIO_KB_OUTPUT (GPIO_ODR_HIGH) -#define GPIO_KB_OUTPUT_COL2 (GPIO_OUT_LOW) -/* - * MEC172xH-SZ (144 pin package) - * KSO00 = GPIO_0040 Func2 bank 1 bit 0 - * KSO01 = GPIO_0045 Func1 bank 1 bit 5 - * KSO02 = GPIO_0046 Func1 bank 1 bit 6 - * KSO03 = GPIO_0047 Func1 bank 1 bit 7 - * KSO04 = GPIO_0107 Func2 bank 2 bit 7 - * KSO05 = GPIO_0112 Func1 bank 2 bit 10 - * KSO06 = GPIO_0113 Func1 bank 2 bit 11 - * KSO07 = GPIO_0120 Func1 bank 2 bit 16 - * KSO08 = GPIO_0121 Func2 bank 2 bit 17 - * KSO09 = GPIO_0122 Func2 bank 2 bit 18 - * KSO10 = GPIO_0123 Func2 bank 2 bit 19 - * KSO11 = GPIO_0124 Func2 bank 2 bit 20 - * KSO12 = GPIO_0125 Func2 bank 2 bit 21 - * For 8x16 keyboard add KSO13 - KSO15 - * KSO13 = GPIO_0126 Func2 bank 2 bit 22 - * KSO14 = GPIO_0152 Func1 bank 3 bit 10 - * KSO15 = GPIO_0151 Func2 bank 3 bit 9 - * - * KSI0 = GPIO_0017 Func1 bank 0 bit 15 - * KSI1 = GPIO_0020 Func1 bank 0 bit 16 - * KSI2 = GPIO_0021 Func1 bank 0 bit 17 - * KSI3 = GPIO_0026 Func1 bank 0 bit 22 - * KSI4 = GPIO_0027 Func1 bank 0 bit 23 - * KSI5 = GPIO_0030 Func1 bank 0 bit 24 - * KSI6 = GPIO_0031 Func1 bank 0 bit 25 - * KSI7 = GPIO_0032 Func1 bank 0 bit 26 - */ -/* KSO 0 Bank 1, Func2, bit 0 */ -ALTERNATE(PIN_MASK(1, 0x01), 2, MODULE_KEYBOARD_SCAN, GPIO_KB_OUTPUT) - -#ifdef CONFIG_KEYBOARD_COL2_INVERTED -/* KSO 1-3 Bank 1, Func1, bits 5-7 */ -ALTERNATE(PIN_MASK(1, 0xA0), 1, MODULE_KEYBOARD_SCAN, GPIO_KB_OUTPUT) -GPIO(KBD_KSO2, PIN(046), GPIO_KB_OUTPUT_COL2) -#else -/* KSO 1-3 Bank 1, Func1, bits 5-7 */ -ALTERNATE(PIN_MASK(1, 0xE0), 1, MODULE_KEYBOARD_SCAN, GPIO_KB_OUTPUT) -#endif - -/* KSO 4, 8-12 Bank 2, Func2, bits 7, 17-21 */ -ALTERNATE(PIN_MASK(2, 0x003E0080), 2, MODULE_KEYBOARD_SCAN, GPIO_KB_OUTPUT) -/* KSO 5-7, Bank 2, Func1, bits 10-11, 16 */ -ALTERNATE(PIN_MASK(2, 0x00010C00), 1, MODULE_KEYBOARD_SCAN, GPIO_KB_OUTPUT) - -/* KSI 0-7, Bank 0, Func1, bit 15-17, 22-26 */ -ALTERNATE(PIN_MASK(0, 0x07C38000), 1, MODULE_KEYBOARD_SCAN, GPIO_KB_INPUT) - -/* - * ESPI_RESET# - GPIO_0061 Func 1, Bank 1 bit[17] - * ESPI_ALERT# - GPIO_0063 Func 1, Bank 1 bit[19] - * ESPI_CLK - GPIO_0065 Func 1, Bank 1 bit[21] - * ESPI_CS# - GPIO_0066 Func 1, Bank 1 bit[22] - * ESPI_IO0 - GPIO_0070 Func 1, Bank 1 bit[24] - * ESPI_IO1 - GPIO_0071 Func 1, Bank 1 bit[25] - * ESPI_IO2 - GPIO_0072 Func 1, Bank 1 bit[26] - * ESPI_IO3 - GPIO_0073 Func 1, Bank 1 bit[27] - */ -ALTERNATE(PIN_MASK(1, 0x0F6A0000), 1, MODULE_LPC, 0) |