diff options
Diffstat (limited to 'board/aleena')
| l--------- | board/aleena/analyzestack.yaml | 1 | ||||
| -rw-r--r-- | board/aleena/battery.c | 121 | ||||
| -rw-r--r-- | board/aleena/board.c | 208 | ||||
| -rw-r--r-- | board/aleena/board.h | 78 | ||||
| -rw-r--r-- | board/aleena/build.mk | 15 | ||||
| -rw-r--r-- | board/aleena/ec.tasklist | 25 | ||||
| -rw-r--r-- | board/aleena/gpio.inc | 122 | ||||
| -rw-r--r-- | board/aleena/led.c | 101 | ||||
| -rw-r--r-- | board/aleena/vif_override.xml | 3 |
9 files changed, 0 insertions, 674 deletions
diff --git a/board/aleena/analyzestack.yaml b/board/aleena/analyzestack.yaml deleted file mode 120000 index 9873122a08..0000000000 --- a/board/aleena/analyzestack.yaml +++ /dev/null @@ -1 +0,0 @@ -../../baseboard/grunt/analyzestack.yaml
\ No newline at end of file diff --git a/board/aleena/battery.c b/board/aleena/battery.c deleted file mode 100644 index b3abae7f73..0000000000 --- a/board/aleena/battery.c +++ /dev/null @@ -1,121 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - * - * Battery pack vendor provided charging profile - */ - -#include "battery_fuel_gauge.h" -#include "common.h" -#include "util.h" - -/* - * Battery info for all Aleena battery types. Note that the fields - * start_charging_min/max and charging_min/max are not used for the charger. - * The effective temperature limits are given by discharging_min/max_c. - * - * Fuel Gauge (FG) parameters which are used for determining if the battery - * is connected, the appropriate ship mode (battery cutoff) command, and the - * charge/discharge FETs status. - * - * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery - * register. For some batteries, the charge/discharge FET bits are set when - * charging/discharging is active, in other types, these bits set mean that - * charging/discharging is disabled. Therefore, in addition to the mask for - * these bits, a disconnect value must be specified. Note that for TI fuel - * gauge, the charge/discharge FET status is found in Operation Status (0x54), - * but a read of Manufacturer Access (0x00) will return the lower 16 bits of - * Operation status which contains the FET status bits. - * - * The assumption for battery types supported is that the charge/discharge FET - * status can be read with a sb_read() command and therefore, only the register - * address, mask, and disconnect value need to be provided. - */ -const struct board_batt_params board_battery_info[] = { - /* Panasonic AP15O5L Battery Information */ - [BATTERY_PANASONIC] = { - .fuel_gauge = { - .manuf_name = "PANASONIC", - .ship_mode = { - .reg_addr = 0x3A, - .reg_data = { 0xC574, 0xC574 }, - }, - .fet = { - .reg_addr = 0x0, - .reg_mask = 0x4000, - .disconnect_val = 0x0, - } - }, - .batt_info = { - .voltage_max = 13200, - .voltage_normal = 11550, /* mV */ - .voltage_min = 9000, /* mV */ - .precharge_current = 256, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 50, - .charging_min_c = 0, - .charging_max_c = 60, - .discharging_min_c = 0, - .discharging_max_c = 60, - }, - }, - - /* Murata AP18C4K Battery Information */ - [BATTERY_MURATA_4012] = { - .fuel_gauge = { - .manuf_name = "Murata KT00304012", - .ship_mode = { - .reg_addr = 0x3A, - .reg_data = { 0xC574, 0xC574 }, - }, - .fet = { - .reg_addr = 0x0, - .reg_mask = 0x2000, - .disconnect_val = 0x2000, - } - }, - .batt_info = { - .voltage_max = 13200, - .voltage_normal = 11400, /* mV */ - .voltage_min = 9000, /* mV */ - .precharge_current = 256, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 50, - .charging_min_c = 0, - .charging_max_c = 60, - .discharging_min_c = -20, - .discharging_max_c = 75, - }, - }, - - /* Murata AP18K4K Battery Information */ - [BATTERY_MURATA_4013] = { - .fuel_gauge = { - .manuf_name = "Murata KT00304013", - .ship_mode = { - .reg_addr = 0x3A, - .reg_data = { 0xC574, 0xC574 }, - }, - .fet = { - .reg_addr = 0x0, - .reg_mask = 0x2000, - .disconnect_val = 0x2000, - } - }, - .batt_info = { - .voltage_max = 13200, - .voltage_normal = 11400, /* mV */ - .voltage_min = 9000, /* mV */ - .precharge_current = 256, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 50, - .charging_min_c = 0, - .charging_max_c = 60, - .discharging_min_c = -20, - .discharging_max_c = 75, - }, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT); - -const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_PANASONIC; diff --git a/board/aleena/board.c b/board/aleena/board.c deleted file mode 100644 index 0343a399c5..0000000000 --- a/board/aleena/board.c +++ /dev/null @@ -1,208 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Aleena board-specific configuration */ - -#include "button.h" -#include "driver/accelgyro_bmi_common.h" -#include "console.h" -#include "driver/accelgyro_icm_common.h" -#include "driver/accelgyro_icm426xx.h" -#include "driver/led/lm3630a.h" -#include "extpower.h" -#include "hooks.h" -#include "i2c.h" -#include "lid_switch.h" -#include "power.h" -#include "power_button.h" -#include "pwm.h" -#include "pwm_chip.h" -#include "switch.h" -#include "tablet_mode.h" -#include "task.h" - -#include "gpio_list.h" - -const enum gpio_signal hibernate_wake_pins[] = { - GPIO_LID_OPEN, - GPIO_AC_PRESENT, - GPIO_POWER_BUTTON_L, - GPIO_EC_RST_ODL, -}; -const int hibernate_wake_pins_used = ARRAY_SIZE(hibernate_wake_pins); - -/* I2C port map. */ -const struct i2c_port_t i2c_ports[] = { - {"power", I2C_PORT_POWER, 100, GPIO_I2C0_SCL, GPIO_I2C0_SDA}, - {"tcpc0", I2C_PORT_TCPC0, 400, GPIO_I2C1_SCL, GPIO_I2C1_SDA}, - {"tcpc1", I2C_PORT_TCPC1, 400, GPIO_I2C2_SCL, GPIO_I2C2_SDA}, - {"thermal", I2C_PORT_THERMAL_AP, 400, GPIO_I2C3_SCL, GPIO_I2C3_SDA}, - {"kblight", I2C_PORT_KBLIGHT, 100, GPIO_I2C5_SCL, GPIO_I2C5_SDA}, - {"sensor", I2C_PORT_SENSOR, 400, GPIO_I2C7_SCL, GPIO_I2C7_SDA}, -}; -const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports); - -/* PWM channels. Must be in the exactly same order as in enum pwm_channel. */ -const struct pwm_t pwm_channels[] = { - [PWM_CH_KBLIGHT] = { - .channel = 5, - .flags = PWM_CONFIG_DSLEEP, - .freq = 100, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT); - -/* Motion sensors */ -static struct mutex icm426xx_mutex; - -static struct icm_drv_data_t g_icm426xx_data; - -enum base_accelgyro_type { - BASE_GYRO_NONE = 0, - BASE_GYRO_BMI160 = 1, - BASE_GYRO_ICM426XX = 2, -}; - -const mat33_fp_t base_standard_ref_icm426xx = { - { 0, FLOAT_TO_FP(-1), 0}, - { FLOAT_TO_FP(1), 0, 0}, - { 0, 0, FLOAT_TO_FP(1)} -}; - -struct motion_sensor_t icm426xx_base_accel = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_ICM426XX, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &icm426xx_drv, - .mutex = &icm426xx_mutex, - .drv_data = &g_icm426xx_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS, - .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs.*/ - .rot_standard_ref = &base_standard_ref_icm426xx, - .min_frequency = ICM426XX_ACCEL_MIN_FREQ, - .max_frequency = ICM426XX_ACCEL_MAX_FREQ, - .config = { - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100, - }, - /* EC use accel for angle detection */ - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, -}; - -struct motion_sensor_t icm426xx_base_gyro = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_ICM426XX, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &icm426xx_drv, - .mutex = &icm426xx_mutex, - .drv_data = &g_icm426xx_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS, - .default_range = 1000, /* dps */ - .rot_standard_ref = &base_standard_ref_icm426xx, - .min_frequency = ICM426XX_GYRO_MIN_FREQ, - .max_frequency = ICM426XX_GYRO_MAX_FREQ, -}; - -static enum base_accelgyro_type base_accelgyro_config; - -void motion_interrupt(enum gpio_signal signal) -{ - switch (base_accelgyro_config) { - case BASE_GYRO_ICM426XX: - icm426xx_interrupt(signal); - break; - case BASE_GYRO_BMI160: - default: - bmi160_interrupt(signal); - break; - } -} - -static void board_detect_motionsensor(void) -{ - int ret; - int val; - - if (chipset_in_state(CHIPSET_STATE_ANY_OFF)) - return; - if (base_accelgyro_config != BASE_GYRO_NONE) - return; - - if (board_is_convertible()) { - /* Check base accelgyro chip */ - ret = icm_read8(&icm426xx_base_accel, - ICM426XX_REG_WHO_AM_I, &val); - if (ret) - ccprints("Get ICM fail."); - if (val == ICM426XX_CHIP_ICM40608) { - motion_sensors[BASE_ACCEL] = icm426xx_base_accel; - motion_sensors[BASE_GYRO] = icm426xx_base_gyro; - } - base_accelgyro_config = (val == ICM426XX_CHIP_ICM40608) - ? BASE_GYRO_ICM426XX : BASE_GYRO_BMI160; - ccprints("Base Accelgyro: %s", (val == ICM426XX_CHIP_ICM40608) - ? "ICM40608" : "BMI160"); - } -} -DECLARE_HOOK(HOOK_CHIPSET_STARTUP, board_detect_motionsensor, - HOOK_PRIO_DEFAULT); -DECLARE_HOOK(HOOK_INIT, board_detect_motionsensor, HOOK_PRIO_INIT_ADC + 2); - -void board_update_sensor_config_from_sku(void) -{ - if (board_is_convertible()) { - /* Enable Gyro interrupts */ - gpio_enable_interrupt(GPIO_6AXIS_INT_L); - } else { - motion_sensor_count = 0; - /* Device is clamshell only */ - tablet_set_mode(0, TABLET_TRIGGER_LID); - /* Gyro is not present, don't allow line to float */ - gpio_set_flags(GPIO_6AXIS_INT_L, - GPIO_INPUT | GPIO_PULL_DOWN); - } -} - -static void board_kblight_init(void) -{ - /* - * Enable keyboard backlight. This needs to be done here because - * the chip doesn't have power until PP3300_S0 comes up. - */ - gpio_set_level(GPIO_KB_BL_EN, 1); - lm3630a_poweron(); -} -DECLARE_HOOK(HOOK_CHIPSET_RESUME, board_kblight_init, HOOK_PRIO_DEFAULT); - -#ifdef CONFIG_KEYBOARD_FACTORY_TEST -/* - * Map keyboard connector pins to EC GPIO pins for factory test. - * Pins mapped to {-1, -1} are skipped. - * The connector has 30 pins total, and there is no pin 0. - */ -const int keyboard_factory_scan_pins[][2] = { - {-1, -1}, {0, 5}, {1, 1}, {1, 0}, {0, 6}, - {0, 7}, {-1, -1}, {-1, -1}, {1, 4}, {1, 3}, - {-1, -1}, {1, 6}, {1, 7}, {3, 1}, {2, 0}, - {1, 5}, {2, 6}, {2, 7}, {2, 1}, {2, 4}, - {2, 5}, {1, 2}, {2, 3}, {2, 2}, {3, 0}, - {-1, -1}, {0, 4}, {-1, -1}, {8, 2}, {-1, -1}, - {-1, -1}, -}; - -const int keyboard_factory_scan_pins_used = - ARRAY_SIZE(keyboard_factory_scan_pins); -#endif diff --git a/board/aleena/board.h b/board/aleena/board.h deleted file mode 100644 index 9ad2a8b94b..0000000000 --- a/board/aleena/board.h +++ /dev/null @@ -1,78 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Aleena board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -#define VARIANT_GRUNT_TCPC_0_ANX3429 - -#include "baseboard.h" - -/* - * By default, enable all console messages excepted HC, ACPI and event: - * The sensor stack is generating a lot of activity. - */ -#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC))) -#undef CONFIG_HOSTCMD_DEBUG_MODE -#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF - -/* Power and battery LEDs */ -#define CONFIG_LED_COMMON -#define CONFIG_CMD_LEDTEST - -#define CONFIG_LED_ONOFF_STATES - -#define I2C_PORT_KBLIGHT NPCX_I2C_PORT5_0 - -/* KB backlight driver */ -#define CONFIG_LED_DRIVER_LM3630A - -#define CONFIG_MKBP_USE_GPIO - -/* Motion sensing drivers */ -#define CONFIG_ACCELGYRO_BMI160 -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) -#define CONFIG_ACCELGYRO_ICM426XX /* Base accel second source*/ -#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) -#define CONFIG_ACCEL_INTERRUPTS -#define CONFIG_ACCEL_KX022 -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO -#define CONFIG_TABLET_MODE -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL -/* - * Slew rate on the PP1800_SENSOR load switch requires a short delay on startup. - */ -#undef CONFIG_MOTION_SENSE_RESUME_DELAY_US -#define CONFIG_MOTION_SENSE_RESUME_DELAY_US (10 * MSEC) - -#define CONFIG_KEYBOARD_FACTORY_TEST - -#ifndef __ASSEMBLER__ - -enum pwm_channel { - PWM_CH_KBLIGHT = 0, - PWM_CH_COUNT -}; - -enum battery_type { - BATTERY_PANASONIC, - BATTERY_MURATA_4012, - BATTERY_MURATA_4013, - BATTERY_TYPE_COUNT, -}; - -void motion_interrupt(enum gpio_signal signal); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ diff --git a/board/aleena/build.mk b/board/aleena/build.mk deleted file mode 100644 index c808e65aed..0000000000 --- a/board/aleena/build.mk +++ /dev/null @@ -1,15 +0,0 @@ -# -*- makefile -*- -# Copyright 2015 The Chromium OS Authors. All rights reserved. -# Use of this source code is governed by a BSD-style license that can be -# found in the LICENSE file. -# -# Board specific files build -# - -CHIP:=npcx -CHIP_FAMILY:=npcx7 -CHIP_VARIANT:=npcx7m6f -BASEBOARD:=grunt - -board-y=board.o led.o -board-$(CONFIG_BATTERY_SMART)+=battery.o diff --git a/board/aleena/ec.tasklist b/board/aleena/ec.tasklist deleted file mode 100644 index dc898c4502..0000000000 --- a/board/aleena/ec.tasklist +++ /dev/null @@ -1,25 +0,0 @@ -/* Copyright 2017 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* - * See CONFIG_TASK_LIST in config.h for details. - */ - -#define CONFIG_TASK_LIST \ - TASK_ALWAYS(HOOKS, hook_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P1, usb_charger_task, 1, TASK_STACK_SIZE) \ - TASK_ALWAYS(CHARGER, charger_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(CHIPSET, chipset_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \ - TASK_ALWAYS(HOSTCMD, host_command_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(CONSOLE, console_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(POWERBTN, power_button_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C0, pd_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C1, pd_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C0, pd_interrupt_handler_task, 0, TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C1, pd_interrupt_handler_task, 1, TASK_STACK_SIZE) diff --git a/board/aleena/gpio.inc b/board/aleena/gpio.inc deleted file mode 100644 index 6fefcf88f1..0000000000 --- a/board/aleena/gpio.inc +++ /dev/null @@ -1,122 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2017 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Declare symbolic names for all the GPIOs that we care about. - * Note: Those with interrupt handlers must be declared first. */ - -GPIO_INT(USB_C0_PD_INT_ODL, PIN(A, 0), GPIO_INT_FALLING, tcpc_alert_event) -GPIO_INT(USB_C1_PD_INT_ODL, PIN(F, 5), GPIO_INT_FALLING, tcpc_alert_event) -GPIO_INT(USB_C0_SWCTL_INT_ODL, PIN(0, 3), GPIO_INT_FALLING, ppc_interrupt) -GPIO_INT(USB_C1_SWCTL_INT_ODL, PIN(D, 4), GPIO_INT_FALLING, ppc_interrupt) -GPIO_INT(PCH_SLP_S3_L, PIN(A, 6), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PCH_SLP_S5_L, PIN(A, 3), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(S0_PGOOD, PIN(F, 4), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(S5_PGOOD, PIN(6, 3), GPIO_INT_BOTH | GPIO_PULL_UP, power_signal_interrupt) -GPIO_INT(POWER_BUTTON_L, PIN(0, 1), GPIO_INT_BOTH, power_button_interrupt) -GPIO_INT(LID_OPEN, PIN(D, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH | GPIO_PULL_UP, lid_interrupt) -GPIO_INT(AC_PRESENT, PIN(0, 0), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, extpower_interrupt) -GPIO_INT(WP_L, PIN(A, 1), GPIO_INT_BOTH, switch_interrupt) -GPIO_INT(VOLUME_DOWN_L, PIN(7, 0), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(VOLUME_UP_L, PIN(7, 5), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(USB_C0_CABLE_DET, PIN(3, 7), GPIO_INT_RISING, anx74xx_cable_det_interrupt) -GPIO_INT(6AXIS_INT_L, PIN(8, 6), GPIO_INT_FALLING | GPIO_SEL_1P8V, motion_interrupt) - -/* GPIO_INT_BOTH is required for PSL wake from hibernate, but we don't need an interrupt handler. */ -GPIO(EC_RST_ODL, PIN(0, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH | GPIO_LOCKED) - -GPIO(EN_PWR_A, PIN(E, 2), GPIO_OUT_LOW) /* Enable Power */ -GPIO(EN_PP1800_SENSOR, PIN(6, 7), GPIO_OUT_LOW) /* Enable Power */ -GPIO(ENABLE_BACKLIGHT_L, PIN(D, 3), GPIO_OUT_HIGH) /* Enable Backlight */ -GPIO(PCH_RSMRST_L, PIN(C, 2), GPIO_OUT_LOW) /* RSMRST# to SOC */ -GPIO(PCH_PWRBTN_L, PIN(C, 1), GPIO_OUT_HIGH) /* Power Button to SOC */ -GPIO(PCH_WAKE_L, PIN(7, 4), GPIO_OUT_HIGH) /* Wake SOC */ -GPIO(SYS_RESET_L, PIN(E, 4), GPIO_ODR_HIGH) /* Cold Reset to SOC */ -GPIO(CCD_MODE_ODL, PIN(E, 3), GPIO_INPUT) /* Case Closed Debug Mode */ -GPIO(ENTERING_RW, PIN(E, 1), GPIO_OUT_LOW) /* EC Entering RW */ -GPIO(EC_BATT_PRES_L, PIN(E, 5), GPIO_INPUT | GPIO_PULL_UP) /* Battery Present */ -GPIO(PCH_SYS_PWROK, PIN(D, 6), GPIO_OUT_LOW) /* Power OK to SOC */ -GPIO(CPU_PROCHOT, PIN(3, 4), GPIO_INPUT | GPIO_SEL_1P8V) /* PROCHOT to SOC */ -GPIO(APU_ALERT_L, PIN(A, 2), GPIO_INPUT) /* Alert to SOC */ -GPIO(3AXIS_INT_L, PIN(5, 0), GPIO_INPUT | GPIO_SEL_1P8V) /* 3 Axis Accel */ -GPIO(KB_BL_EN, PIN(F, 2), GPIO_OUT_LOW) /* Enable KB Backlight */ -GPIO(EC_INT_L, PIN(A, 4), GPIO_ODR_HIGH) /* Sensor MKBP event to SOC */ - -/* I2C pins - these will be reconfigured for alternate function below */ -GPIO(I2C0_SCL, PIN(B, 5), GPIO_INPUT) /* EC_I2C_POWER_SCL */ -GPIO(I2C0_SDA, PIN(B, 4), GPIO_INPUT) /* EC_I2C_POWER_SDA */ -GPIO(I2C1_SCL, PIN(9, 0), GPIO_INPUT) /* EC_I2C_USB_C0_PD_SCL */ -GPIO(I2C1_SDA, PIN(8, 7), GPIO_INPUT) /* EC_I2C_USB_C0_PD_SDA */ -GPIO(I2C2_SCL, PIN(9, 2), GPIO_INPUT) /* EC_I2C_USB_C1_PD_SCL */ -GPIO(I2C2_SDA, PIN(9, 1), GPIO_INPUT) /* EC_I2C_USB_C1_PD_SDA */ -GPIO(I2C3_SCL, PIN(D, 1), GPIO_INPUT | GPIO_SEL_1P8V) /* APU_SIC */ -GPIO(I2C3_SDA, PIN(D, 0), GPIO_INPUT | GPIO_SEL_1P8V) /* APU_SID */ -GPIO(I2C5_SCL, PIN(3, 3), GPIO_INPUT) /* EC_I2C_EEPROM_SCL and - EC_I2C_KB_BL_SCL */ -GPIO(I2C5_SDA, PIN(3, 6), GPIO_INPUT) /* EC_I2C_EEPROM_SDA and - EC_I2C_KB_BL_SDA */ -GPIO(I2C7_SCL, PIN(B, 3), GPIO_INPUT | GPIO_SEL_1P8V) /* EC_I2C_SENSOR_SCL */ -GPIO(I2C7_SDA, PIN(B, 2), GPIO_INPUT | GPIO_SEL_1P8V) /* EC_I2C_SENSOR_SDA */ - -/* - * The NPCX LPC driver configures and controls SCI and SMI, - * so PCH_SCI_ODL [PIN(7, 6)] and PCH_SMI_ODL [PIN(C, 6)] are - * not defined here as GPIOs. - */ - -GPIO(EN_USB_A0_5V, PIN(6, 1), GPIO_OUT_LOW) /* Enable A0 5V Charging */ -GPIO(EN_USB_A1_5V, PIN(C, 0), GPIO_OUT_LOW) /* Enable A1 5V Charging */ -GPIO(EN_USB_C0_TCPC_PWR, PIN(6, 0), GPIO_OUT_LOW) /* Enable C0 TCPC Power */ -GPIO(USB_C0_OC_L, PIN(7, 3), GPIO_OUT_HIGH) /* C0 Over Current */ -GPIO(USB_C1_OC_L, PIN(7, 2), GPIO_OUT_HIGH) /* C1 Over Current */ -GPIO(USB_C0_PD_RST_L, PIN(3, 2), GPIO_OUT_HIGH) /* C0 PD Reset */ -GPIO(USB_C1_PD_RST_L, PIN(D, 5), GPIO_OUT_HIGH) /* C1 PD Reset */ -GPIO(USB_C0_BC12_VBUS_ON_L, PIN(4, 0), GPIO_ODR_HIGH) /* C0 BC1.2 Power */ -GPIO(USB_C1_BC12_VBUS_ON_L, PIN(B, 1), GPIO_ODR_HIGH | GPIO_PULL_UP) /* C1 BC1.2 Power */ -GPIO(USB_C0_BC12_CHG_DET, PIN(6, 2), GPIO_INPUT) /* C0 BC1.2 Detect */ -GPIO(USB_C1_BC12_CHG_DET, PIN(8, 3), GPIO_INPUT | GPIO_PULL_DOWN) /* C1 BC1.2 Detect */ -GPIO(USB_C0_DP_HPD, PIN(9, 5), GPIO_OUT_LOW) /* C0 DP Hotplug Detect */ -GPIO(USB_C1_DP_HPD, PIN(9, 6), GPIO_OUT_LOW) /* C1 DP Hotplug Detect */ - -/* Board ID */ -GPIO(BOARD_VERSION1, PIN(C, 7), GPIO_INPUT) -GPIO(BOARD_VERSION2, PIN(9, 3), GPIO_INPUT) -GPIO(BOARD_VERSION3, PIN(8, 0), GPIO_INPUT) -GPIO(SKU_ID1, PIN(F, 0), GPIO_INPUT) -GPIO(SKU_ID2, PIN(4, 1), GPIO_INPUT) - -/* LED */ -GPIO(BAT_LED_1_L, PIN(C, 3), GPIO_OUT_HIGH) -GPIO(BAT_LED_2_L, PIN(C, 4), GPIO_OUT_HIGH) - -/* Alternate functions GPIO definitions */ -/* Cr50 requires no pull-ups on UART pins. */ -ALTERNATE(PIN_MASK(6, 0x30), 0, MODULE_UART, 0) /* UART from EC to Servo */ -ALTERNATE(PIN_MASK(B, 0x30), 0, MODULE_I2C, 0) /* I2C0 */ -ALTERNATE(PIN_MASK(9, 0x07), 0, MODULE_I2C, 0) /* I2C1 SCL / I2C2 */ -ALTERNATE(PIN_MASK(8, 0x80), 0, MODULE_I2C, 0) /* I2C1 SDA */ -ALTERNATE(PIN_MASK(D, 0x03), 0, MODULE_I2C, 0) /* I2C3 */ -ALTERNATE(PIN_MASK(3, 0x48), 0, MODULE_I2C, 0) /* I2C5 */ -ALTERNATE(PIN_MASK(B, 0x0C), 0, MODULE_I2C, 0) /* I2C7 */ -ALTERNATE(PIN_MASK(4, 0x30), 0, MODULE_ADC, 0) /* ADC0-1 */ -ALTERNATE(PIN_MASK(4, 0x02), 0, MODULE_ADC, 0) /* ADC4 */ -ALTERNATE(PIN_MASK(F, 0x02), 0, MODULE_ADC, 0) /* ADC8 */ -ALTERNATE(PIN_MASK(F, 0x01), 0, MODULE_ADC, 0) /* ADC9 */ -ALTERNATE(PIN_MASK(B, 0x80), 0, MODULE_PWM, 0) /* KB Backlight */ - -/* Keyboard Pins */ -ALTERNATE(PIN_MASK(3, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_INPUT) /* KSI_00-01 */ -ALTERNATE(PIN_MASK(2, 0xFC), 0, MODULE_KEYBOARD_SCAN, GPIO_INPUT) /* KSI_02-07 */ -ALTERNATE(PIN_MASK(2, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_00-01 */ -GPIO(KBD_KSO2, PIN(1, 7), GPIO_OUT_LOW) /* KSO_02 inverted */ -ALTERNATE(PIN_MASK(1, 0x7F), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_03-09 */ -ALTERNATE(PIN_MASK(0, 0xE0), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_10-12 */ - -/* Power Switch Logic (PSL) inputs */ -ALTERNATE(PIN_MASK(0, 0x07), 0, MODULE_PMU, 0) /* GPIO00 = AC_PRESENT, - GPIO01 = POWER_BUTTON_L, - GPIO02 = EC_RST_ODL */ -ALTERNATE(PIN_MASK(D, 0x04), 0, MODULE_PMU, 0) /* GPIOD2 = LID_OPEN */ diff --git a/board/aleena/led.c b/board/aleena/led.c deleted file mode 100644 index 4774a39045..0000000000 --- a/board/aleena/led.c +++ /dev/null @@ -1,101 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "common.h" -#include "led_onoff_states.h" -#include "led_common.h" -#include "gpio.h" -#include "hooks.h" -#include "console.h" - -#define CPRINTS(format, args...) cprints(CC_HOOK, format, ## args) - -#define LED_OFF_LVL 1 -#define LED_ON_LVL 0 - -__override const int led_charge_lvl_1; - -__override const int led_charge_lvl_2 = 100; - -/* - * board_id others 5, 6 - * led1 Amber Blue - * led2 Blue Amber - */ -static enum gpio_signal led_amber = GPIO_BAT_LED_1_L; -static enum gpio_signal led_blue = GPIO_BAT_LED_2_L; - -/* Note there is only LED for charge / power */ -__override struct led_descriptor - led_bat_state_table[LED_NUM_STATES][LED_NUM_PHASES] = { - [STATE_CHARGING_LVL_2] = {{EC_LED_COLOR_AMBER, LED_INDEFINITE} }, - [STATE_CHARGING_FULL_CHARGE] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} }, - [STATE_DISCHARGE_S0] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} }, - [STATE_DISCHARGE_S3] = {{EC_LED_COLOR_AMBER, 1 * LED_ONE_SEC}, - {LED_OFF, 3 * LED_ONE_SEC} }, - [STATE_DISCHARGE_S5] = {{LED_OFF, LED_INDEFINITE} }, - [STATE_BATTERY_ERROR] = {{EC_LED_COLOR_AMBER, 1 * LED_ONE_SEC}, - {LED_OFF, 1 * LED_ONE_SEC} }, - [STATE_FACTORY_TEST] = {{EC_LED_COLOR_BLUE, 2 * LED_ONE_SEC}, - {EC_LED_COLOR_AMBER, 2 * LED_ONE_SEC} }, -}; - -const enum ec_led_id supported_led_ids[] = { EC_LED_ID_BATTERY_LED }; - -const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids); - -static void board_led_init(void) -{ - int board_id = - (gpio_get_level(GPIO_BOARD_VERSION3) << 2) | - (gpio_get_level(GPIO_BOARD_VERSION2) << 1) | - (gpio_get_level(GPIO_BOARD_VERSION1) << 0); - - CPRINTS("board_id=%d", board_id); - - if ((board_id == 5) || (board_id == 6)) { - led_amber = GPIO_BAT_LED_2_L; - led_blue = GPIO_BAT_LED_1_L; - CPRINTS("LED: switch LED"); - } - -} -DECLARE_HOOK(HOOK_INIT, board_led_init, HOOK_PRIO_DEFAULT); - -__override void led_set_color_battery(enum ec_led_colors color) -{ - switch (color) { - case EC_LED_COLOR_BLUE: - gpio_set_level(led_blue, LED_ON_LVL); - gpio_set_level(led_amber, LED_OFF_LVL); - break; - case EC_LED_COLOR_AMBER: - gpio_set_level(led_blue, LED_OFF_LVL); - gpio_set_level(led_amber, LED_ON_LVL); - break; - default: /* LED_OFF and other unsupported colors */ - gpio_set_level(led_blue, LED_OFF_LVL); - gpio_set_level(led_amber, LED_OFF_LVL); - break; - } -} - -void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range) -{ - brightness_range[EC_LED_COLOR_BLUE] = 1; - brightness_range[EC_LED_COLOR_AMBER] = 1; -} - -int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness) -{ - if (brightness[EC_LED_COLOR_BLUE] != 0) - led_set_color_battery(EC_LED_COLOR_BLUE); - else if (brightness[EC_LED_COLOR_AMBER] != 0) - led_set_color_battery(EC_LED_COLOR_AMBER); - else - led_set_color_battery(LED_OFF); - - return EC_SUCCESS; -} diff --git a/board/aleena/vif_override.xml b/board/aleena/vif_override.xml deleted file mode 100644 index 32736caf64..0000000000 --- a/board/aleena/vif_override.xml +++ /dev/null @@ -1,3 +0,0 @@ -<!-- Add VIF field overrides here. See genvif.c and the Vendor Info File - Definition from the USB-IF. ---> |