1 files changed, 0 insertions, 170 deletions
diff --git a/board/asurada/gpio.inc b/board/asurada/gpio.inc
deleted file mode 100644
index 75d1fbafa5..0000000000
--- a/board/asurada/gpio.inc
+++ /dev/null
@@ -1,170 +0,0 @@
-/* -*- mode:c -*-
- *
- * Copyright 2020 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Declare symbolic names for all the GPIOs that we care about.
- * Note: Those with interrupt handlers must be declared first. */
-
-/* Wake Source interrupts */
-GPIO_INT(POWER_BUTTON_L,     PIN(E, 4), GPIO_INT_BOTH | GPIO_PULL_UP |
-	 GPIO_HIB_WAKE_HIGH, power_button_interrupt) /* H1_EC_PWR_BTN_ODL */
-GPIO_INT(LID_OPEN,           PIN(E, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH,
-         lid_interrupt)
-GPIO_INT(TABLET_MODE_L,      PIN(J, 7), GPIO_INT_BOTH,
-         gmr_tablet_switch_isr)
-
-/* Chipset interrupts */
-GPIO_INT(AP_EC_WARM_RST_REQ, PIN(D, 3), GPIO_INT_RISING | GPIO_SEL_1P8V,
-         chipset_reset_request_interrupt)
-
-/* Power sequencing interrupts */
-GPIO_INT(AP_EC_WATCHDOG_L, PIN(C, 7), GPIO_INT_BOTH | GPIO_SEL_1P8V,
-         chipset_watchdog_interrupt)
-GPIO_INT(AP_IN_SLEEP_L, PIN(F, 2),
-         GPIO_INT_BOTH | GPIO_PULL_DOWN | GPIO_SEL_1P8V, power_signal_interrupt)
-GPIO_INT(PMIC_EC_PWRGD, PIN(F, 3),
-         GPIO_INT_BOTH | GPIO_PULL_DOWN | GPIO_SEL_1P8V, power_signal_interrupt)
-
-/* Sensor Interrupts */
-GPIO_INT(BASE_IMU_INT_L,     PIN(J, 2), GPIO_INT_FALLING | GPIO_SEL_1P8V,
-         motion_interrupt)
-GPIO_INT(LID_ACCEL_INT_L,    PIN(J, 3), GPIO_INT_FALLING | GPIO_SEL_1P8V,
-         lis2dw12_interrupt)
-#ifdef BOARD_ASURADA_REV0
-GPIO_INT(ALS_RGB_INT_ODL,    PIN(F, 0), GPIO_INT_FALLING,
-         tcs3400_interrupt)
-#else
-GPIO(ALS_RGB_INT_ODL,        PIN(F, 0), GPIO_INPUT)
-#endif
-
-/* USB-C interrupts */
-GPIO_INT(USB_C0_PPC_INT_ODL, PIN(D, 1), GPIO_INT_BOTH, ppc_interrupt)
-GPIO_INT(USB_C0_BC12_INT_ODL,PIN(J, 6), GPIO_INT_FALLING, bc12_interrupt)
-GPIO_INT(USB_C1_BC12_INT_L,  PIN(J, 4), GPIO_INT_FALLING, bc12_interrupt)
-
-/* Volume button interrupts */
-/* Note that netnames are reversed in asurada rev 0/1 */
-GPIO_INT(VOLUME_DOWN_L,      PIN(D, 5), GPIO_INT_BOTH | GPIO_PULL_UP,
-         button_interrupt) /* EC_VOLDN_BTN_ODL */
-GPIO_INT(VOLUME_UP_L,        PIN(D, 6), GPIO_INT_BOTH | GPIO_PULL_UP,
-         button_interrupt) /* EC_VOLUP_BTN_ODL */
-
-/* Other interrupts */
-GPIO_INT(AP_XHCI_INIT_DONE,  PIN(D, 2), GPIO_INT_BOTH | GPIO_PULL_DOWN | GPIO_SEL_1P8V,
-         usb_a0_interrupt)
-#ifdef BOARD_ASURADA_REV0
-GPIO_INT(AC_PRESENT,         PIN(M, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH,
-         extpower_interrupt) /* AC_OK / AC_PRESENT in rev0 */
-#else /* HAYATO */
-GPIO_INT(AC_PRESENT,         PIN(E, 5), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH,
-         extpower_interrupt) /* AC_OK / AC_PRESENT in rev1+ */
-#endif
-GPIO_INT(UART1_RX,           PIN(B, 0), GPIO_INT_FALLING,
-         uart_deepsleep_interrupt) /* UART_DEBUG_TX_EC_RX */
-GPIO_INT(WP,                 PIN(I, 4), GPIO_INT_BOTH | GPIO_SEL_1P8V,
-         switch_interrupt) /* EC_FLASH_WP_OD */
-GPIO_INT(SPI0_CS,            PIN(M, 5), GPIO_INT_FALLING,
-         spi_event)        /* SPI slave Chip Select -- AP_SPI_EC_CS_L */
-GPIO_INT(X_EC_GPIO2,         PIN(B, 2), GPIO_ODR_HIGH, x_ec_interrupt)
-
-/* Power Sequencing Signals */
-GPIO(EC_PMIC_EN_ODL,         PIN(D, 0), GPIO_ODR_HIGH | GPIO_SEL_1P8V)
-GPIO(EC_PMIC_WATCHDOG_L,     PIN(H, 0), GPIO_ODR_LOW | GPIO_SEL_1P8V)
-GPIO(EN_PP5000_A,            PIN(C, 6), GPIO_OUT_HIGH)
-GPIO(PG_MT6315_PROC_ODL,     PIN(E, 1), GPIO_INPUT)
-GPIO(PG_MT6360_ODL,          PIN(F, 1), GPIO_INPUT)
-GPIO(PG_PP5000_A_ODL,        PIN(A, 6), GPIO_INPUT)
-GPIO(EN_SLP_Z,               PIN(E, 3), GPIO_OUT_LOW)
-GPIO(SYS_RST_ODL,            PIN(B, 6), GPIO_ODR_LOW)
-GPIO(EC_BL_EN_OD,            PIN(B, 5), GPIO_ODR_LOW | GPIO_SEL_1P8V)
-
-/* MKBP event synchronization */
-GPIO(EC_INT_L,               PIN(E, 6), GPIO_ODR_HIGH | GPIO_SEL_1P8V) /* EC_AP_INT_ODL */
-
-/* USB and USBC Signals */
-GPIO(DP_AUX_PATH_SEL,        PIN(G, 0), GPIO_OUT_HIGH)
-GPIO(EC_DPBRDG_HPD_ODL,      PIN(J, 0), GPIO_ODR_HIGH | GPIO_SEL_1P8V)
-GPIO(EN_PP5000_USB_A0_VBUS,  PIN(B, 7), GPIO_OUT_LOW)
-GPIO(USB_C0_FRS_EN,          PIN(H, 3), GPIO_OUT_LOW)
-
-/* Misc Signals */
-GPIO(EC_BATT_PRES_ODL,       PIN(C, 0), GPIO_INPUT)
-GPIO(BC12_DET_EN,            PIN(J, 5), GPIO_OUT_LOW) /* EN_USB_C0_BC12_DET */
-GPIO(EN_EC_ID_ODL,           PIN(H, 5), GPIO_ODR_LOW)
-GPIO(ENTERING_RW,            PIN(C, 5), GPIO_OUT_LOW) /* EC_ENTERING_RW */
-GPIO(EN_5V_USM,              PIN(D, 7), GPIO_OUT_LOW)
-
-/* I2C pins - Alternate function below configures I2C module on these pins */
-GPIO(I2C_A_SCL,              PIN(B, 3), GPIO_INPUT) /* I2C_CHG_BATT_SCL */
-GPIO(I2C_A_SDA,              PIN(B, 4), GPIO_INPUT) /* I2C_CHG_BATT_SDA */
-GPIO(I2C_B_SCL,              PIN(C, 1), GPIO_INPUT | GPIO_SEL_1P8V) /* I2C_SENSOR_SCL */
-GPIO(I2C_B_SDA,              PIN(C, 2), GPIO_INPUT | GPIO_SEL_1P8V) /* I2C_SENSOR_SDA */
-GPIO(I2C_C_SCL,              PIN(F, 6), GPIO_INPUT) /* I2C_USB_C0_SCL */
-GPIO(I2C_C_SDA,              PIN(F, 7), GPIO_INPUT) /* I2C_USB_C0_SCL */
-GPIO(I2C_E_SCL,              PIN(E, 0), GPIO_INPUT) /* I2C_USB_C1_SCL */
-GPIO(I2C_E_SDA,              PIN(E, 7), GPIO_INPUT) /* I2C_USB_C1_SDA */
-
-/* SPI pins - Alternate function below configures SPI module on these pins */
-
-/* NC / TP */
-
-/* Keyboard pins */
-
-/* Subboards HDMI/TYPEC */
-GPIO(EC_X_GPIO1,             PIN(H, 4), GPIO_OUT_LOW)
-GPIO(EC_X_GPIO3,             PIN(J, 1), GPIO_INPUT)
-
-/* Alternate functions GPIO definitions */
-ALTERNATE(PIN_MASK(B, 0x18), 1, MODULE_I2C, 0) /* I2C A */
-ALTERNATE(PIN_MASK(C, 0x06), 1, MODULE_I2C, GPIO_SEL_1P8V) /* I2C B */
-ALTERNATE(PIN_MASK(F, 0xC0), 1, MODULE_I2C, 0) /* I2C C */
-ALTERNATE(PIN_MASK(E, 0x81), 1, MODULE_I2C, 0) /* I2C E */
-
-/* UART */
-ALTERNATE(PIN_MASK(B, 0x03), 1, MODULE_UART, 0) /* EC to Servo */
-
-/* PWM */
-ALTERNATE(PIN_MASK(A, 0x07), 1, MODULE_PWM, 0) /* PWM 0~2 */
-
-/* ADC */
-ALTERNATE(PIN_MASK(I, 0x6F), 0, MODULE_ADC, 0) /* ADC 0,1,2,3,5,6 */
-
-/* SPI */
-ALTERNATE(PIN_MASK(M, 0x33), 0, MODULE_SPI, 0) /* SPI */
-
-/* Unimplemented Pins  */
-GPIO(SET_VMC_VOLT_AT_1V8,    PIN(D, 4), GPIO_INPUT | GPIO_PULL_DOWN | GPIO_SEL_1P8V)
-GPIO(PACKET_MODE_EN,         PIN(A, 3), GPIO_INPUT | GPIO_PULL_DOWN)
-/* b/160218054: behavior not defined */
-/* *_ODL pin has external pullup so don't pull it down. */
-GPIO(USB_A0_FAULT_ODL,       PIN(A, 7), GPIO_INPUT)
-GPIO(CHARGER_PROCHOT_ODL,    PIN(C, 3), GPIO_INPUT)
-GPIO(PG_MT6315_GPU_ODL,      PIN(H, 6), GPIO_INPUT)
-GPIO(EN_PP3000_SD_U,         PIN(G, 1), GPIO_INPUT | GPIO_PULL_DOWN | GPIO_SEL_1P8V)
-/* reserved for future use */
-GPIO(CCD_MODE_ODL,           PIN(C, 4), GPIO_INPUT)
-/*
- * ADC pins don't have internal pull-down capability,
- * so we set them as output low.
- */
-GPIO(NC_GPI7,                PIN(I, 7), GPIO_OUT_LOW)
-/* NC pins, enable internal pull-up/down to avoid floating state. */
-#ifdef BOARD_ASURADA_REV0
-GPIO(NC_GPE5,                PIN(E, 5), GPIO_INPUT | GPIO_PULL_UP)
-#else /* HAYATO */
-GPIO(NC_GPM2,                PIN(M, 2), GPIO_INPUT | GPIO_PULL_DOWN)
-#endif
-GPIO(NC_GPM3,                PIN(M, 3), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(NC_GPM6,                PIN(M, 6), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(SPI_CLK_GPG6,           PIN(G, 6), GPIO_INPUT | GPIO_PULL_UP)
-/*
- * These 4 pins don't have internal pull-down capability,
- * so we set them as output low.
- */
-GPIO(NC_GPG3,                PIN(G, 3), GPIO_OUT_LOW)
-GPIO(SPI_MOSI_GPG4,          PIN(G, 4), GPIO_OUT_LOW)
-GPIO(SPI_MISO_GPG5,          PIN(G, 5), GPIO_OUT_LOW)
-GPIO(SPI_CS_GPG7,            PIN(G, 7), GPIO_OUT_LOW)