diff options
Diffstat (limited to 'board/atlas/board.c')
| -rw-r--r-- | board/atlas/board.c | 629 |
1 files changed, 0 insertions, 629 deletions
diff --git a/board/atlas/board.c b/board/atlas/board.c deleted file mode 100644 index 4881ed6898..0000000000 --- a/board/atlas/board.c +++ /dev/null @@ -1,629 +0,0 @@ -/* Copyright 2018 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Atlas board-specific configuration */ - -#include "adc_chip.h" -#include "bd99992gw.h" -#include "board_config.h" -#include "charge_manager.h" -#include "charger.h" -#include "charge_state.h" -#include "chipset.h" -#include "console.h" -#include "driver/als_opt3001.h" -#include "driver/pmic_bd99992gw.h" -#include "driver/charger/isl923x.h" -#include "driver/tcpm/ps8xxx.h" -#include "driver/tcpm/tcpci.h" -#include "driver/tcpm/tcpm.h" -#include "espi.h" -#include "extpower.h" -#include "gpio.h" -#include "hooks.h" -#include "host_command.h" -#include "i2c.h" -#include "keyboard_8042_sharedlib.h" -#include "keyboard_scan.h" -#include "lid_switch.h" -#include "motion_sense.h" -#include "power_button.h" -#include "power.h" -#include "pwm_chip.h" -#include "pwm.h" -#include "spi.h" -#include "switch.h" -#include "system.h" -#include "system_chip.h" -#include "task.h" -#include "temp_sensor.h" -#include "timer.h" -#include "uart.h" -#include "usb_mux.h" -#include "usb_pd.h" -#include "usb_pd_tcpm.h" -#include "util.h" - -#define CPRINTS(format, args...) cprints(CC_SYSTEM, format, ## args) -#define CPRINTF(format, args...) cprintf(CC_SYSTEM, format, ## args) - -static void tcpc_alert_event(enum gpio_signal signal) -{ - int port = -1; - - switch (signal) { - case GPIO_USB_C0_PD_INT_ODL: - port = 0; - break; - case GPIO_USB_C1_PD_INT_ODL: - port = 1; - break; - default: - return; - } - - schedule_deferred_pd_interrupt(port); -} - -#include "gpio_list.h" - -/* Keyboard scan. Increase output_settle_us to 80us from default 50us. */ -__override struct keyboard_scan_config keyscan_config = { - .output_settle_us = 80, - .debounce_down_us = 9 * MSEC, - .debounce_up_us = 30 * MSEC, - .scan_period_us = 3 * MSEC, - .min_post_scan_delay_us = 1000, - .poll_timeout_us = 100 * MSEC, - .actual_key_mask = { - 0x3c, 0xff, 0xff, 0xff, 0xff, 0xf5, 0xff, - 0xa4, 0xff, 0xfe, 0x55, 0xfa, 0xca /* full set */ - }, -}; - -/* PWM channels. Must be in the exactly same order as in enum pwm_channel. */ -const struct pwm_t pwm_channels[] = { - [PWM_CH_KBLIGHT] = { 3, 0, 10000 }, - [PWM_CH_DB0_LED_BLUE] = { - 0, PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, 2400 }, - [PWM_CH_DB0_LED_RED] = { - 2, PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, 2400 }, - [PWM_CH_DB0_LED_GREEN] = { - 6, PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, 2400 }, - [PWM_CH_DB1_LED_BLUE] = { - 1, PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, 2400 }, - [PWM_CH_DB1_LED_RED] = { - 7, PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, 2400 }, - [PWM_CH_DB1_LED_GREEN] = { - 5, PWM_CONFIG_ACTIVE_LOW | PWM_CONFIG_DSLEEP, 2400 }, -}; -BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT); - -/* Hibernate wake configuration */ -const enum gpio_signal hibernate_wake_pins[] = { - GPIO_ROP_EC_ACOK, - GPIO_LID_OPEN, - GPIO_MECH_PWR_BTN_ODL, -}; -const int hibernate_wake_pins_used = ARRAY_SIZE(hibernate_wake_pins); - -const struct adc_t adc_channels[] = { - /* - * Adapter current output or battery charging/discharging current (uV) - * 18x amplification on charger side. - */ - [ADC_AMON_BMON] = { - "AMON_BMON", - NPCX_ADC_CH2, - ADC_MAX_VOLT*1000/18, - ADC_READ_MAX+1, - 0 - }, - /* - * ISL9238 PSYS output is 1.44 uA/W over 12.4K resistor, to read - * 0.8V @ 45 W, i.e. 56250 uW/mV. Using ADC_MAX_VOLT*56250 and - * ADC_READ_MAX+1 as multiplier/divider leads to overflows, so we - * only divide by 2 (enough to avoid precision issues). - */ - [ADC_PSYS] = { - "PSYS", - NPCX_ADC_CH3, - ADC_MAX_VOLT*56250*2/(ADC_READ_MAX+1), - 2, - 0 - }, -}; -BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT); - -/* I2C port map */ -const struct i2c_port_t i2c_ports[] = { - {"power", I2C_PORT_POWER, 100, - GPIO_EC_I2C0_POWER_SCL, GPIO_EC_I2C0_POWER_SDA}, - {"tcpc0", I2C_PORT_TCPC0, 1000, - GPIO_EC_I2C1_USB_C0_SCL, GPIO_EC_I2C1_USB_C0_SDA}, - {"tcpc1", I2C_PORT_TCPC1, 1000, - GPIO_EC_I2C2_USB_C1_SCL, GPIO_EC_I2C2_USB_C1_SDA}, - {"sensor", I2C_PORT_SENSOR, 100, - GPIO_EC_I2C3_SENSOR_3V3_SCL, GPIO_EC_I2C3_SENSOR_3V3_SDA}, - {"battery", I2C_PORT_BATTERY, 100, - GPIO_EC_I2C4_BATTERY_SCL, GPIO_EC_I2C4_BATTERY_SDA}, -}; -const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports); - -/* Charger Chips */ -const struct charger_config_t chg_chips[] = { - { - .i2c_port = I2C_PORT_CHARGER, - .i2c_addr_flags = ISL923X_ADDR_FLAGS, - .drv = &isl923x_drv, - }, -}; - -/* TCPC mux configuration */ -const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_MAX_COUNT] = { - { - /* left port */ - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_TCPC0, - .addr_flags = I2C_ADDR_TCPC_FLAGS, - }, - .drv = &ps8xxx_tcpm_drv, - /* Alert is active-low, push-pull */ - .flags = 0, - }, - { - /* right port */ - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_TCPC1, - .addr_flags = I2C_ADDR_TCPC_FLAGS, - }, - .drv = &ps8xxx_tcpm_drv, - /* Alert is active-low, push-pull */ - .flags = 0, - }, -}; - -const struct usb_mux usb_muxes[CONFIG_USB_PD_PORT_MAX_COUNT] = { - { - .usb_port = 0, - .driver = &tcpci_tcpm_usb_mux_driver, - .hpd_update = &ps8xxx_tcpc_update_hpd_status, - }, - { - .usb_port = 1, - .driver = &tcpci_tcpm_usb_mux_driver, - .hpd_update = &ps8xxx_tcpc_update_hpd_status, - }, -}; - -void board_reset_pd_mcu(void) -{ - gpio_set_level(GPIO_USB_PD_RST_L, 0); - msleep(PS8XXX_RST_L_RST_H_DELAY_MS); - gpio_set_level(GPIO_USB_PD_RST_L, 1); -} - -void board_tcpc_init(void) -{ - /* Only reset TCPC if not sysjump */ - if (!system_jumped_late()) - board_reset_pd_mcu(); - - gpio_enable_interrupt(GPIO_USB_C0_PD_INT_ODL); - gpio_enable_interrupt(GPIO_USB_C1_PD_INT_ODL); - - /* - * Initialize HPD to low; after sysjump SOC needs to see - * HPD pulse to enable video path - */ - for (int port = 0; port < CONFIG_USB_PD_PORT_MAX_COUNT; ++port) - usb_mux_hpd_update(port, USB_PD_MUX_HPD_LVL_DEASSERTED | - USB_PD_MUX_HPD_IRQ_DEASSERTED); -} -DECLARE_HOOK(HOOK_INIT, board_tcpc_init, HOOK_PRIO_INIT_I2C+1); - -uint16_t tcpc_get_alert_status(void) -{ - uint16_t status = 0; - - if (!gpio_get_level(GPIO_USB_C0_PD_INT_ODL)) { - if (gpio_get_level(GPIO_USB_C0_PD_RST_L)) - status |= PD_STATUS_TCPC_ALERT_0; - } - - if (!gpio_get_level(GPIO_USB_C1_PD_INT_ODL)) { - if (gpio_get_level(GPIO_USB_C1_PD_RST_L)) - status |= PD_STATUS_TCPC_ALERT_1; - } - - return status; -} - -const struct temp_sensor_t temp_sensors[] = { - {"Battery", TEMP_SENSOR_TYPE_BATTERY, charge_get_battery_temp, 0}, - /* BD99992GW temp sensors are only readable in S0 */ - {"Ambient", TEMP_SENSOR_TYPE_BOARD, bd99992gw_get_val, - BD99992GW_ADC_CHANNEL_SYSTHERM0}, - {"Charger", TEMP_SENSOR_TYPE_BOARD, bd99992gw_get_val, - BD99992GW_ADC_CHANNEL_SYSTHERM1}, - {"DRAM", TEMP_SENSOR_TYPE_BOARD, bd99992gw_get_val, - BD99992GW_ADC_CHANNEL_SYSTHERM2}, - {"eMMC", TEMP_SENSOR_TYPE_BOARD, bd99992gw_get_val, - BD99992GW_ADC_CHANNEL_SYSTHERM3}, -}; -BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT); - -/* - * Check if PMIC fault registers indicate VR fault. If yes, print out fault - * register info to console. Additionally, set panic reason so that the OS can - * check for fault register info by looking at offset 0x14(PWRSTAT1) and - * 0x15(PWRSTAT2) in cros ec panicinfo. - */ -static void board_report_pmic_fault(const char *str) -{ - int vrfault, pwrstat1 = 0, pwrstat2 = 0; - uint32_t info; - - /* RESETIRQ1 -- Bit 4: VRFAULT */ - if (i2c_read8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_RESETIRQ1, &vrfault) != EC_SUCCESS) - return; - - if (!(vrfault & BIT(4))) - return; - - /* VRFAULT has occurred, print VRFAULT status bits. */ - - /* PWRSTAT1 */ - i2c_read8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_PWRSTAT1, &pwrstat1); - - /* PWRSTAT2 */ - i2c_read8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_PWRSTAT2, &pwrstat2); - - CPRINTS("PMIC VRFAULT: %s", str); - CPRINTS("PMIC VRFAULT: PWRSTAT1=0x%02x PWRSTAT2=0x%02x", pwrstat1, - pwrstat2); - - /* Clear all faults -- Write 1 to clear. */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_RESETIRQ1, BIT(4)); - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_PWRSTAT1, pwrstat1); - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_PWRSTAT2, pwrstat2); - - /* - * Status of the fault registers can be checked in the OS by looking at - * offset 0x14(PWRSTAT1) and 0x15(PWRSTAT2) in cros ec panicinfo. - */ - info = ((pwrstat2 & 0xFF) << 8) | (pwrstat1 & 0xFF); - panic_set_reason(PANIC_SW_PMIC_FAULT, info, 0); -} - -static void board_pmic_disable_slp_s0_vr_decay(void) -{ - /* - * VCCIOCNT: - * Bit 6 (0) - Disable decay of VCCIO on SLP_S0# assertion - * Bits 5:4 (11) - Nominal output voltage: 0.850V - * Bits 3:2 (10) - VR set to AUTO on SLP_S0# de-assertion - * Bits 1:0 (10) - VR set to AUTO operating mode - */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_VCCIOCNT, 0x3a); - - /* - * V18ACNT: - * Bits 7:6 (00) - Disable low power mode on SLP_S0# assertion - * Bits 5:4 (10) - Nominal voltage set to 1.8V - * Bits 3:2 (10) - VR set to AUTO on SLP_S0# de-assertion - * Bits 1:0 (10) - VR set to AUTO operating mode - */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_V18ACNT, 0x2a); - - /* - * V085ACNT: - * Bits 7:6 (00) - Disable low power mode on SLP_S0# assertion - * Bits 5:4 (10) - Nominal voltage 0.85V - * Bits 3:2 (10) - VR set to AUTO on SLP_S0# de-assertion - * Bits 1:0 (10) - VR set to AUTO operating mode - */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_V085ACNT, 0x2a); -} - -static void board_pmic_enable_slp_s0_vr_decay(void) -{ - /* - * VCCIOCNT: - * Bit 6 (1) - Enable decay of VCCIO on SLP_S0# assertion - * Bits 5:4 (11) - Nominal output voltage: 0.850V - * Bits 3:2 (10) - VR set to AUTO on SLP_S0# de-assertion - * Bits 1:0 (10) - VR set to AUTO operating mode - */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_VCCIOCNT, 0x7a); - - /* - * V18ACNT: - * Bits 7:6 (01) - Enable low power mode on SLP_S0# assertion - * Bits 5:4 (10) - Nominal voltage set to 1.8V - * Bits 3:2 (10) - VR set to AUTO on SLP_S0# de-assertion - * Bits 1:0 (10) - VR set to AUTO operating mode - */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_V18ACNT, 0x6a); - - /* - * V085ACNT: - * Bits 7:6 (01) - Enable low power mode on SLP_S0# assertion - * Bits 5:4 (10) - Nominal voltage 0.85V - * Bits 3:2 (10) - VR set to AUTO on SLP_S0# de-assertion - * Bits 1:0 (10) - VR set to AUTO operating mode - */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_V085ACNT, 0x6a); -} - -__override void power_board_handle_host_sleep_event( - enum host_sleep_event state) -{ - if (state == HOST_SLEEP_EVENT_S0IX_SUSPEND) - board_pmic_enable_slp_s0_vr_decay(); - else if (state == HOST_SLEEP_EVENT_S0IX_RESUME) - board_pmic_disable_slp_s0_vr_decay(); -} - -static void board_pmic_init(void) -{ - board_report_pmic_fault("SYSJUMP"); - - /* Clear power source events */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_PWRSRCINT, 0xff); - - /* Disable power button shutdown timer */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_PBCONFIG, 0x00); - - if (system_jumped_late()) - return; - - /* DISCHGCNT1 - enable 100 ohm discharge on VCCIO */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_DISCHGCNT1, 0x01); - - /* - * DISCHGCNT2 - enable 100 ohm discharge on - * V5.0A, V3.3DSW, V3.3A and V1.8A - */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_DISCHGCNT2, 0x55); - - /* - * DISCHGCNT3 - enable 500 ohm discharge on - * V1.8U_2.5U - * DISCHGCNT3 - enable 100 ohm discharge on - * V12U, V1.00A, V0.85A - */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_DISCHGCNT3, 0xd5); - - /* DISCHGCNT4 - enable 100 ohm discharge on V33S, V18S, V100S */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_DISCHGCNT4, 0x15); - - /* VRMODECTRL - disable low-power mode for all rails */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_VRMODECTRL, 0x1f); - - /* V5ADS3CNT - boost V5A_DS3 by 2% */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_V5ADS3CNT, 0x1a); - - board_pmic_disable_slp_s0_vr_decay(); -} -DECLARE_HOOK(HOOK_INIT, board_pmic_init, HOOK_PRIO_DEFAULT); - -void board_hibernate(void) -{ - int p; - - /* Configure PSL pins */ - for (p = 0; p < hibernate_wake_pins_used; p++) - system_config_psl_mode(hibernate_wake_pins[p]); - - /* - * Enter PSL mode. Note that on Atlas, simply enabling PSL mode does - * not cut the EC's power. Therefore, we'll need to cut off power via - * the ROP PMIC afterwards. - */ - system_enter_psl_mode(); - - /* Cut off DSW power via the ROP PMIC. */ - i2c_write8(I2C_PORT_PMIC, I2C_ADDR_BD99992_FLAGS, - BD99992GW_REG_SDWNCTRL, BD99992GW_SDWNCTRL_SWDN); - - /* Wait for power to be cut. */ - while (1) - ; -} - -/* Initialize board. */ -static void board_init(void) -{ - if (system_get_board_version() < ATLAS_REV_FIXED_EC_WP) { - int dflags; - - CPRINTS("Applying EC_WP_L workaround"); - dflags = gpio_get_default_flags(GPIO_EC_WP_L); - gpio_set_flags(GPIO_EC_WP_L, dflags | GPIO_PULL_UP); - } - - /* Provide AC status to the PCH */ - gpio_set_level(GPIO_PCH_ACOK, extpower_is_present()); -} -DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); - -static void board_extpower(void) -{ - gpio_set_level(GPIO_PCH_ACOK, extpower_is_present()); -} -DECLARE_HOOK(HOOK_AC_CHANGE, board_extpower, HOOK_PRIO_DEFAULT); - -/** - * Set active charge port -- only one port can be active at a time. - * - * @param charge_port Charge port to enable. - * - * Returns EC_SUCCESS if charge port is accepted and made active, - * EC_ERROR_* otherwise. - */ -int board_set_active_charge_port(int charge_port) -{ - /* charge port is a physical port */ - int is_real_port = (charge_port >= 0 && - charge_port < CONFIG_USB_PD_PORT_MAX_COUNT); - /* check if we are sourcing VBUS on the port */ - int is_source = gpio_get_level(charge_port == 0 ? - GPIO_USB_C0_5V_EN : GPIO_USB_C1_5V_EN); - - if (is_real_port && is_source) { - CPRINTS("No charging from p%d", charge_port); - return EC_ERROR_INVAL; - } - - CPRINTS("New chg p%d", charge_port); - - if (charge_port == CHARGE_PORT_NONE) { - /* Disable both ports */ - gpio_set_level(GPIO_EN_USB_C0_CHARGE_L, 1); - gpio_set_level(GPIO_EN_USB_C1_CHARGE_L, 1); - } else { - /* Make sure non-charging port is disabled */ - gpio_set_level(charge_port ? GPIO_EN_USB_C0_CHARGE_L : - GPIO_EN_USB_C1_CHARGE_L, 1); - /* Enable charging port */ - gpio_set_level(charge_port ? GPIO_EN_USB_C1_CHARGE_L : - GPIO_EN_USB_C0_CHARGE_L, 0); - } - - return EC_SUCCESS; -} - -/* - * Limit the input current to 95% negotiated limit, - * to account for the charger chip margin. - */ - -static int charger_derate(int current) -{ - return current * 95 / 100; -} - -static void board_charger_init(void) -{ - charger_set_input_current_limit(CHARGER_SOLO, - charger_derate(PD_MAX_CURRENT_MA)); -} -DECLARE_HOOK(HOOK_INIT, board_charger_init, HOOK_PRIO_DEFAULT); - -/** - * Set the charge limit based upon desired maximum. - * - * @param port Port number. - * @param supplier Charge supplier type. - * @param charge_ma Desired charge limit (mA). - * @param charge_mv Negotiated charge voltage (mV). - */ -void board_set_charge_limit(int port, int supplier, int charge_ma, - int max_ma, int charge_mv) -{ - charge_ma = charger_derate(charge_ma); - charge_set_input_current_limit(MAX(charge_ma, - CONFIG_CHARGER_INPUT_CURRENT), charge_mv); -} - -static void board_chipset_suspend(void) -{ - gpio_set_level(GPIO_KBD_BL_EN, 0); -} -DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, board_chipset_suspend, HOOK_PRIO_DEFAULT); - -static void board_chipset_resume(void) -{ - gpio_set_level(GPIO_KBD_BL_EN, 1); -} -DECLARE_HOOK(HOOK_CHIPSET_RESUME, board_chipset_resume, HOOK_PRIO_DEFAULT); - -static void board_chipset_reset(void) -{ - board_report_pmic_fault("CHIPSET RESET"); -} -DECLARE_HOOK(HOOK_CHIPSET_RESET, board_chipset_reset, HOOK_PRIO_DEFAULT); - -int board_get_version(void) -{ - static int ver; - - if (!ver) { - /* - * Read the board EC ID on the tristate strappings - * using ternary encoding: 0 = 0, 1 = 1, Hi-Z = 2 - */ - uint8_t id0, id1, id2; - - id0 = gpio_get_ternary(GPIO_BOARD_VERSION1); - id1 = gpio_get_ternary(GPIO_BOARD_VERSION2); - id2 = gpio_get_ternary(GPIO_BOARD_VERSION3); - - ver = (id2 * 9) + (id1 * 3) + id0; - CPRINTS("Board ID = %d", ver); - } - - return ver; -} - -static struct opt3001_drv_data_t g_opt3001_data = { - .scale = 1, - .uscale = 0, - .offset = 0, -}; - -struct motion_sensor_t motion_sensors[] = { - [LID_ALS] = { - .name = "Light", - .active_mask = SENSOR_ACTIVE_S0, - .chip = MOTIONSENSE_CHIP_OPT3001, - .type = MOTIONSENSE_TYPE_LIGHT, - .location = MOTIONSENSE_LOC_LID, - .drv = &opt3001_drv, - .drv_data = &g_opt3001_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = OPT3001_I2C_ADDR_FLAGS, - .rot_standard_ref = NULL, - .default_range = 0x2b11a1, /* from nocturne */ - .min_frequency = OPT3001_LIGHT_MIN_FREQ, - .max_frequency = OPT3001_LIGHT_MAX_FREQ, - .config = { - /* Sensor on in S0 */ - [SENSOR_CONFIG_EC_S0] = { - .odr = 1000, - }, - }, - }, -}; -const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -/* ALS instances when LPC mapping is needed. Each entry directs to a sensor. */ -const struct motion_sensor_t *motion_als_sensors[] = { - &motion_sensors[LID_ALS], -}; -BUILD_ASSERT(ARRAY_SIZE(motion_als_sensors) == ALS_COUNT); |