diff options
Diffstat (limited to 'board/boten')
| -rw-r--r-- | board/boten/battery.c | 121 | ||||
| -rw-r--r-- | board/boten/board.c | 509 | ||||
| -rw-r--r-- | board/boten/board.h | 143 | ||||
| -rw-r--r-- | board/boten/build.mk | 15 | ||||
| -rw-r--r-- | board/boten/cbi_ssfc.c | 36 | ||||
| -rw-r--r-- | board/boten/cbi_ssfc.h | 60 | ||||
| -rw-r--r-- | board/boten/ec.tasklist | 22 | ||||
| -rw-r--r-- | board/boten/gpio.inc | 146 | ||||
| -rw-r--r-- | board/boten/led.c | 112 | ||||
| -rw-r--r-- | board/boten/usb_pd_policy.c | 71 | ||||
| -rw-r--r-- | board/boten/vif_override.xml | 3 |
11 files changed, 0 insertions, 1238 deletions
diff --git a/board/boten/battery.c b/board/boten/battery.c deleted file mode 100644 index 0f4c8ffeb9..0000000000 --- a/board/boten/battery.c +++ /dev/null @@ -1,121 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - * - * Battery pack vendor provided charging profile - */ - -#include "battery_fuel_gauge.h" -#include "charge_state.h" -#include "common.h" - -/* - * Battery info for all boten battery types. Note that the fields - * start_charging_min/max and charging_min/max are not used for the charger. - * The effective temperature limits are given by discharging_min/max_c. - * - * Fuel Gauge (FG) parameters which are used for determining if the battery - * is connected, the appropriate ship mode (battery cutoff) command, and the - * charge/discharge FETs status. - * - * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery - * register. For some batteries, the charge/discharge FET bits are set when - * charging/discharging is active, in other types, these bits set mean that - * charging/discharging is disabled. Therefore, in addition to the mask for - * these bits, a disconnect value must be specified. Note that for TI fuel - * gauge, the charge/discharge FET status is found in Operation Status (0x54), - * but a read of Manufacturer Access (0x00) will return the lower 16 bits of - * Operation status which contains the FET status bits. - * - * The assumption for battery types supported is that the charge/discharge FET - * status can be read with a sb_read() command and therefore, only the register - * address, mask, and disconnect value need to be provided. - */ -const struct board_batt_params board_battery_info[] = { - /* SMP L18D3PG1 Battery Information */ - [BATTERY_SMP] = { - .fuel_gauge = { - .manuf_name = "SMP", - .ship_mode = { - .reg_addr = 0x34, - .reg_data = { 0x0000, 0x1000 }, - }, - .fet = { - .reg_addr = 0x00, - .reg_mask = 0x0018, - .disconnect_val = 0x0000, - } - }, - .batt_info = { - .voltage_max = 13050, /* mV */ - .voltage_normal = 11250, /* mV */ - .voltage_min = 9000, /* mV */ - .precharge_current = 256, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 50, - .charging_min_c = 0, - .charging_max_c = 60, - .discharging_min_c = -20, - .discharging_max_c = 60, - }, - }, - - /* LGC L17L3PB0 Battery Information */ - [BATTERY_LGC] = { - .fuel_gauge = { - .manuf_name = "LGC", - .ship_mode = { - .reg_addr = 0x34, - .reg_data = { 0x0000, 0x1000 }, - }, - .fet = { - .reg_addr = 0x00, - .reg_mask = 0x0018, - .disconnect_val = 0x0000, - } - }, - .batt_info = { - .voltage_max = 13050, /* mV */ - .voltage_normal = 11400, /* mV */ - .voltage_min = 9000, /* mV */ - .precharge_current = 256, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 50, - .charging_min_c = 0, - .charging_max_c = 60, - .discharging_min_c = -20, - .discharging_max_c = 73, - }, - }, - - /* Sunwoda L17M3PB0 Battery Information */ - [BATTERY_SUNWODA] = { - .fuel_gauge = { - .manuf_name = "SUNWODA", - .ship_mode = { - .reg_addr = 0x34, - .reg_data = { 0x0000, 0x1000 }, - }, - .fet = { - .reg_addr = 0x00, - .reg_mask = 0x0018, - .disconnect_val = 0x0000, - } - }, - .batt_info = { - .voltage_max = 13050, /* mV */ - .voltage_normal = 11250, /* mV */ - .voltage_min = 9000, /* mV */ - .precharge_current = 186, /* mA */ - .start_charging_min_c = 0, - .start_charging_max_c = 50, - .charging_min_c = 0, - .charging_max_c = 60, - .discharging_min_c = -20, - .discharging_max_c = 60, - }, - }, -}; -BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT); - -const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_SMP; diff --git a/board/boten/board.c b/board/boten/board.c deleted file mode 100644 index b6301834bf..0000000000 --- a/board/boten/board.c +++ /dev/null @@ -1,509 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Boten board-specific configuration */ - -#include "adc_chip.h" -#include "button.h" -#include "charge_manager.h" -#include "charge_state_v2.h" -#include "charger.h" -#include "driver/accel_lis2dw12.h" -#include "driver/accelgyro_lsm6dsm.h" -#include "driver/bc12/pi3usb9201.h" -#include "driver/charger/isl923x.h" -#include "driver/temp_sensor/thermistor.h" -#include "driver/tcpm/raa489000.h" -#include "driver/tcpm/tcpci.h" -#include "driver/usb_mux/it5205.h" -#include "gpio.h" -#include "hooks.h" -#include "intc.h" -#include "keyboard_scan.h" -#include "lid_switch.h" -#include "power.h" -#include "power_button.h" -#include "pwm.h" -#include "pwm_chip.h" -#include "switch.h" -#include "system.h" -#include "tablet_mode.h" -#include "task.h" -#include "tcpm/tcpci.h" -#include "temp_sensor.h" -#include "uart.h" -#include "usb_charge.h" -#include "usb_mux.h" -#include "usb_pd.h" -#include "usb_pd_tcpm.h" - -#define CPRINTUSB(format, args...) cprints(CC_USBCHARGE, format, ## args) -#define INT_RECHECK_US 5000 - -/* C0 interrupt line shared by BC 1.2 and charger */ -static void check_c0_line(void); -DECLARE_DEFERRED(check_c0_line); - -static void hdmi_hpd_interrupt(enum gpio_signal s) -{ - gpio_set_level(GPIO_USB_C1_DP_HPD, !gpio_get_level(s)); -} - -static void notify_c0_chips(void) -{ - /* - * The interrupt line is shared between the TCPC and BC 1.2 detection - * chip. Therefore we'll need to check both ICs. - */ - schedule_deferred_pd_interrupt(0); - task_set_event(TASK_ID_USB_CHG_P0, USB_CHG_EVENT_BC12); -} - -static void check_c0_line(void) -{ - /* - * If line is still being held low, see if there's more to process from - * one of the chips - */ - if (!gpio_get_level(GPIO_USB_C0_INT_ODL)) { - notify_c0_chips(); - hook_call_deferred(&check_c0_line_data, INT_RECHECK_US); - } -} - -static void usb_c0_interrupt(enum gpio_signal s) -{ - /* Cancel any previous calls to check the interrupt line */ - hook_call_deferred(&check_c0_line_data, -1); - - /* Notify all chips using this line that an interrupt came in */ - notify_c0_chips(); - - /* Check the line again in 5ms */ - hook_call_deferred(&check_c0_line_data, INT_RECHECK_US); - -} - -static void c0_ccsbu_ovp_interrupt(enum gpio_signal s) -{ - cprints(CC_USBPD, "C0: CC OVP, SBU OVP, or thermal event"); - pd_handle_cc_overvoltage(0); -} - -/** - * Deferred function to handle pen detect change - */ -static void pendetect_deferred(void) -{ - static int debounced_pen_detect; - int pen_detect = !gpio_get_level(GPIO_PEN_DET_ODL); - - if (pen_detect == debounced_pen_detect) - return; - - debounced_pen_detect = pen_detect; - - gpio_set_level(GPIO_EN_PP5000_PEN, debounced_pen_detect); - gpio_set_level(GPIO_PEN_DET_PCH, !debounced_pen_detect); -} -DECLARE_DEFERRED(pendetect_deferred); - -void pen_detect_interrupt(enum gpio_signal s) -{ - /* Trigger deferred notification of pen detect change */ - hook_call_deferred(&pendetect_deferred_data, - 500 * MSEC); -} - -void board_hibernate(void) -{ - /* - * Charger IC need to be put into their "low power mode" before - * entering the Z-state. - */ - raa489000_hibernate(0, false); -} - -__override void board_pulse_entering_rw(void) -{ - /* - * On the ITE variants, the EC_ENTERING_RW signal was connected to a pin - * which is active high by default. This causes Cr50 to think that the - * EC has jumped to its RW image even though this may not be the case. - * The pin is changed to GPIO_EC_ENTERING_RW2. - */ - gpio_set_level(GPIO_EC_ENTERING_RW, 1); - gpio_set_level(GPIO_EC_ENTERING_RW2, 1); - usleep(MSEC); - gpio_set_level(GPIO_EC_ENTERING_RW, 0); - gpio_set_level(GPIO_EC_ENTERING_RW2, 0); -} - -/* Must come after other header files and interrupt handler declarations */ -#include "gpio_list.h" - -/* ADC channels */ -const struct adc_t adc_channels[] = { - [ADC_VSNS_PP3300_A] = { - .name = "PP3300_A_PGOOD", - .factor_mul = ADC_MAX_MVOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - .channel = CHIP_ADC_CH0 - }, - [ADC_TEMP_SENSOR_1] = { - .name = "TEMP_SENSOR1", - .factor_mul = ADC_MAX_MVOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - .channel = CHIP_ADC_CH2 - }, - [ADC_TEMP_SENSOR_2] = { - .name = "TEMP_SENSOR2", - .factor_mul = ADC_MAX_MVOLT, - .factor_div = ADC_READ_MAX + 1, - .shift = 0, - .channel = CHIP_ADC_CH3 - }, -}; -BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT); - -/* BC 1.2 chips */ -const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = { - { - .i2c_port = I2C_PORT_USB_C0, - .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS, - .flags = PI3USB9201_ALWAYS_POWERED, - }, -}; - -/* Charger chips */ -const struct charger_config_t chg_chips[] = { - { - .i2c_port = I2C_PORT_USB_C0, - .i2c_addr_flags = ISL923X_ADDR_FLAGS, - .drv = &isl923x_drv, - }, -}; - -/* TCPCs */ -const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_MAX_COUNT] = { - { - .bus_type = EC_BUS_TYPE_I2C, - .i2c_info = { - .port = I2C_PORT_USB_C0, - .addr_flags = RAA489000_TCPC0_I2C_FLAGS, - }, - .flags = TCPC_FLAGS_TCPCI_REV2_0, - .drv = &raa489000_tcpm_drv, - }, -}; - -/* USB Muxes */ -const struct usb_mux usb_muxes[CONFIG_USB_PD_PORT_MAX_COUNT] = { - { - .usb_port = 0, - .i2c_port = I2C_PORT_USB_C0, - .i2c_addr_flags = IT5205_I2C_ADDR1_FLAGS, - .driver = &it5205_usb_mux_driver, - }, -}; - -/* USB-A charging control */ -const int usb_port_enable[USB_PORT_COUNT] = { - GPIO_EN_USB_A0_VBUS, -}; - -void board_init(void) -{ - gpio_enable_interrupt(GPIO_USB_C0_INT_ODL); - gpio_enable_interrupt(GPIO_USB_C0_CCSBU_OVP_ODL); - /* Enable gpio interrupt for base accelgyro sensor */ - gpio_enable_interrupt(GPIO_BASE_SIXAXIS_INT_L); - gpio_enable_interrupt(GPIO_HDMI_HPD_SUB_ODL); - /* Enable gpio interrupt for pen detect */ - gpio_enable_interrupt(GPIO_PEN_DET_ODL); - - /* Make sure pen detection is triggered or not at sysjump */ - if (!gpio_get_level(GPIO_PEN_DET_ODL)) - gpio_set_level(GPIO_EN_PP5000_PEN, 1); - - if (gpio_get_level(GPIO_PEN_DET_ODL)) - gpio_set_level(GPIO_PEN_DET_PCH, 1); - - /* Set LEDs luminance */ - pwm_set_duty(PWM_CH_LED_RED, 70); - pwm_set_duty(PWM_CH_LED_GREEN, 70); - pwm_set_duty(PWM_CH_LED_WHITE, 70); - - /* - * If interrupt lines are already low, schedule them to be processed - * after inits are completed. - */ - if (!gpio_get_level(GPIO_USB_C0_INT_ODL)) - hook_call_deferred(&check_c0_line_data, 0); -} -DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT); - -void board_reset_pd_mcu(void) -{ - /* - * Nothing to do. TCPC C0 is internal, TCPC C1 reset pin is not - * connected to the EC. - */ -} - -uint16_t tcpc_get_alert_status(void) -{ - uint16_t status = 0; - int regval; - - /* - * The interrupt line is shared between the TCPC and BC1.2 detector IC. - * Therefore, go out and actually read the alert registers to report the - * alert status. - */ - if (!gpio_get_level(GPIO_USB_C0_INT_ODL)) { - if (!tcpc_read16(0, TCPC_REG_ALERT, ®val)) { - /* The TCPCI Rev 1.0 spec says to ignore bits 14:12. */ - if (!(tcpc_config[0].flags & TCPC_FLAGS_TCPCI_REV2_0)) - regval &= ~((1 << 14) | (1 << 13) | (1 << 12)); - - if (regval) - status |= PD_STATUS_TCPC_ALERT_0; - } - } - - return status; -} - -void board_set_charge_limit(int port, int supplier, int charge_ma, int max_ma, - int charge_mv) -{ - int icl = MAX(charge_ma, CONFIG_CHARGER_INPUT_CURRENT); - - /* - * b/147463641: The charger IC seems to overdraw ~4%, therefore we - * reduce our target accordingly. - */ - icl = icl * 96 / 100; - charge_set_input_current_limit(icl, charge_mv); -} - -__override void typec_set_source_current_limit(int port, enum tcpc_rp_value rp) -{ - if (port < 0 || port > board_get_usb_pd_port_count()) - return; - - raa489000_set_output_current(port, rp); -} - -int board_is_sourcing_vbus(int port) -{ - int regval; - - tcpc_read(port, TCPC_REG_POWER_STATUS, ®val); - return !!(regval & TCPC_REG_POWER_STATUS_SOURCING_VBUS); - -} - -int board_set_active_charge_port(int port) -{ - if (port != 0 && port != CHARGE_PORT_NONE) - return EC_ERROR_INVAL; - - CPRINTUSB("New chg p%d", port); - - /* Disable all ports. */ - if (port == CHARGE_PORT_NONE) { - tcpc_write(0, TCPC_REG_COMMAND, - TCPC_REG_COMMAND_SNK_CTRL_LOW); - raa489000_enable_asgate(0, false); - return EC_SUCCESS; - } - - /* Check if port is sourcing VBUS. */ - if (board_is_sourcing_vbus(port)) { - CPRINTUSB("Skip enable p%d", port); - return EC_ERROR_INVAL; - } - - /* Enable requested charge port. */ - if (raa489000_enable_asgate(port, true) || - tcpc_write(0, TCPC_REG_COMMAND, - TCPC_REG_COMMAND_SNK_CTRL_HIGH)) { - CPRINTUSB("p%d: sink path enable failed.", port); - return EC_ERROR_UNKNOWN; - } - - return EC_SUCCESS; -} - -/* PWM channels. Must be in the exactly same order as in enum pwm_channel. */ -const struct pwm_t pwm_channels[] = { - [PWM_CH_KBLIGHT] = { - .channel = 0, - .flags = PWM_CONFIG_DSLEEP, - .freq_hz = 10000, - }, - - [PWM_CH_LED_RED] = { - .channel = 1, - .flags = PWM_CONFIG_DSLEEP | PWM_CONFIG_ACTIVE_LOW, - .freq_hz = 2400, - }, - - [PWM_CH_LED_GREEN] = { - .channel = 2, - .flags = PWM_CONFIG_DSLEEP | PWM_CONFIG_ACTIVE_LOW, - .freq_hz = 2400, - }, - - [PWM_CH_LED_WHITE] = { - .channel = 3, - .flags = PWM_CONFIG_DSLEEP | PWM_CONFIG_ACTIVE_LOW, - .freq_hz = 2400, - } - -}; -BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT); - -/* Sensor Mutexes */ -static struct mutex g_lid_mutex; -static struct mutex g_base_mutex; - -/* Matrices to rotate accelerometers into the standard reference. */ -static const mat33_fp_t lid_standard_ref = { - { FLOAT_TO_FP(1), 0, 0}, - { 0, FLOAT_TO_FP(-1), 0}, - { 0, 0, FLOAT_TO_FP(-1)} -}; - -static const mat33_fp_t base_standard_ref = { - { FLOAT_TO_FP(1), 0, 0}, - { 0, FLOAT_TO_FP(1), 0}, - { 0, 0, FLOAT_TO_FP(1)} -}; - -/* Sensor Data */ -static struct stprivate_data g_lis2dwl_data; -static struct lsm6dsm_data lsm6dsm_data = LSM6DSM_DATA; - -/* Drivers */ -struct motion_sensor_t motion_sensors[] = { - [LID_ACCEL] = { - .name = "Lid Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LIS2DWL, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_LID, - .drv = &lis2dw12_drv, - .mutex = &g_lid_mutex, - .drv_data = &g_lis2dwl_data, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LIS2DWL_ADDR1_FLAGS, - .rot_standard_ref = &lid_standard_ref, - .default_range = 2, /* g */ - .min_frequency = LIS2DW12_ODR_MIN_VAL, - .max_frequency = LIS2DW12_ODR_MAX_VAL, - .config = { - [SENSOR_CONFIG_EC_S0] = { - .odr = 12500 | ROUND_UP_FLAG, - }, - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - }, - }, - }, - [BASE_ACCEL] = { - .name = "Base Accel", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LSM6DSM, - .type = MOTIONSENSE_TYPE_ACCEL, - .location = MOTIONSENSE_LOC_BASE, - .drv = &lsm6dsm_drv, - .mutex = &g_base_mutex, - .drv_data = LSM6DSM_ST_DATA(lsm6dsm_data, - MOTIONSENSE_TYPE_ACCEL), - .int_signal = GPIO_BASE_SIXAXIS_INT_L, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS, - .rot_standard_ref = &base_standard_ref, - .default_range = 4, /* g */ - .min_frequency = LSM6DSM_ODR_MIN_VAL, - .max_frequency = LSM6DSM_ODR_MAX_VAL, - .config = { - [SENSOR_CONFIG_EC_S0] = { - .odr = 13000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - [SENSOR_CONFIG_EC_S3] = { - .odr = 10000 | ROUND_UP_FLAG, - .ec_rate = 100 * MSEC, - }, - }, - }, - [BASE_GYRO] = { - .name = "Base Gyro", - .active_mask = SENSOR_ACTIVE_S0_S3, - .chip = MOTIONSENSE_CHIP_LSM6DSM, - .type = MOTIONSENSE_TYPE_GYRO, - .location = MOTIONSENSE_LOC_BASE, - .drv = &lsm6dsm_drv, - .mutex = &g_base_mutex, - .drv_data = LSM6DSM_ST_DATA(lsm6dsm_data, - MOTIONSENSE_TYPE_GYRO), - .int_signal = GPIO_BASE_SIXAXIS_INT_L, - .flags = MOTIONSENSE_FLAG_INT_SIGNAL, - .port = I2C_PORT_SENSOR, - .i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS, - .default_range = 1000 | ROUND_UP_FLAG, /* dps */ - .rot_standard_ref = &base_standard_ref, - .min_frequency = LSM6DSM_ODR_MIN_VAL, - .max_frequency = LSM6DSM_ODR_MAX_VAL, - }, -}; - -const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors); - -/* Thermistors */ -const struct temp_sensor_t temp_sensors[] = { - [TEMP_SENSOR_1] = {.name = "Memory", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = get_temp_3v3_51k1_47k_4050b, - .idx = ADC_TEMP_SENSOR_1}, - [TEMP_SENSOR_2] = {.name = "Ambient", - .type = TEMP_SENSOR_TYPE_BOARD, - .read = get_temp_3v3_51k1_47k_4050b, - .idx = ADC_TEMP_SENSOR_2}, -}; -BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT); - -/* This callback disables keyboard when convertibles are fully open */ -__override void lid_angle_peripheral_enable(int enable) -{ - int chipset_in_s0 = chipset_in_state(CHIPSET_STATE_ON); - - /* - * If the lid is in tablet position via other sensors, - * ignore the lid angle, which might be faulty then - * disable keyboard. - */ - if (tablet_get_mode()) - enable = 0; - - if (enable) { - keyboard_scan_enable(1, KB_SCAN_DISABLE_LID_ANGLE); - } else { - /* - * Ensure that the chipset is off before disabling the keyboard. - * When the chipset is on, the EC keeps the keyboard enabled and - * the AP decides whether to ignore input devices or not. - */ - if (!chipset_in_s0) - keyboard_scan_enable(0, KB_SCAN_DISABLE_LID_ANGLE); - } -} diff --git a/board/boten/board.h b/board/boten/board.h deleted file mode 100644 index 0e2a72015c..0000000000 --- a/board/boten/board.h +++ /dev/null @@ -1,143 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Boten board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* Select Baseboard features */ -#define VARIANT_DEDEDE_EC_IT8320 -#include "baseboard.h" - -/* Battery */ -#define CONFIG_BATTERY_FUEL_GAUGE -#define CONFIG_BATTERY_V2 -#define CONFIG_BATTERY_COUNT 1 -#define CONFIG_HOSTCMD_BATTERY_V2 - -/* BC 1.2 */ -#define CONFIG_BC12_DETECT_PI3USB9201 - -/* Charger */ -#define CONFIG_CHARGE_RAMP_HW -#define CONFIG_CHARGER_RAA489000 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_OCPC_DEF_RBATT_MOHMS 22 /* R_DS(on) 11.6mOhm + 10mOhm sns rstr */ -#undef CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE -#define CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE (100 * MSEC) - -/* DAC for PSYS */ -#define CONFIG_DAC - -/* LED */ -#define CONFIG_LED_ONOFF_STATES - -/* PWM */ -#define CONFIG_PWM - -/* Sensors */ -#define CONFIG_ACCEL_LIS2DWL /* Lid accel */ -#define CONFIG_ACCELGYRO_LSM6DSM /* Base accel */ -#define CONFIG_ACCEL_LSM6DSM_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL) - -#define CONFIG_ACCEL_INTERRUPTS -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* Power of 2 - Too large of a fifo causes too much timestamp jitter */ -#define CONFIG_ACCEL_FIFO_SIZE 256 -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) - -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL - -#define CONFIG_TABLET_MODE -#define CONFIG_TABLET_MODE_SWITCH -#define CONFIG_GMR_TABLET_MODE - -/* TCPC */ -#define CONFIG_USB_PD_PORT_MAX_COUNT 1 -#define CONFIG_USB_PD_TCPM_RAA489000 - -/* USB defines specific to external TCPCs */ -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_VBUS_DETECT_TCPC -#define CONFIG_USB_PD_DISCHARGE_TCPC -#define CONFIG_USB_PD_TCPC_LOW_POWER - -/* EC console commands */ -#define CONFIG_CMD_TCPC_DUMP -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO - -/* Variant references the TCPCs to determine Vbus sourcing */ -#define CONFIG_USB_PD_5V_EN_CUSTOM - -/* Thermistors */ -#define CONFIG_TEMP_SENSOR -#define CONFIG_THERMISTOR -#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B - -/* USB Mux */ -#define CONFIG_USB_MUX_IT5205 - -/* USB Type A Features */ -#define USB_PORT_COUNT 1 -#define CONFIG_USB_PORT_POWER_DUMB - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -enum pwm_channel { - PWM_CH_KBLIGHT, - PWM_CH_LED_RED, - PWM_CH_LED_GREEN, - PWM_CH_LED_WHITE, - PWM_CH_COUNT, -}; - -/* Motion sensors */ -enum sensor_id { - LID_ACCEL, - BASE_ACCEL, - BASE_GYRO, - SENSOR_COUNT -}; - -/* ADC channels */ -enum adc_channel { - ADC_VSNS_PP3300_A, /* ADC0 */ - ADC_TEMP_SENSOR_1, /* ADC2 */ - ADC_TEMP_SENSOR_2, /* ADC3 */ - ADC_CH_COUNT -}; - -enum temp_sensor_id { - TEMP_SENSOR_1, - TEMP_SENSOR_2, - TEMP_SENSOR_COUNT -}; - -/* List of possible batteries */ -enum battery_type { - BATTERY_SMP, - BATTERY_LGC, - BATTERY_SUNWODA, - BATTERY_TYPE_COUNT, -}; - -void pen_detect_interrupt(enum gpio_signal s); - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ diff --git a/board/boten/build.mk b/board/boten/build.mk deleted file mode 100644 index 806168ea0d..0000000000 --- a/board/boten/build.mk +++ /dev/null @@ -1,15 +0,0 @@ -# -*- makefile -*- -# Copyright 2020 The Chromium OS Authors. All rights reserved. -# Use of this source code is governed by a BSD-style license that can be -# found in the LICENSE file. -# -# Board specific files build -# - -CHIP:=it83xx -CHIP_FAMILY:=it8320 -CHIP_VARIANT:=it8320dx -BASEBOARD:=dedede - -board-y=board.o cbi_ssfc.o led.o usb_pd_policy.o -board-$(CONFIG_BATTERY_SMART)+=battery.o diff --git a/board/boten/cbi_ssfc.c b/board/boten/cbi_ssfc.c deleted file mode 100644 index c4b859f133..0000000000 --- a/board/boten/cbi_ssfc.c +++ /dev/null @@ -1,36 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "cbi_ssfc.h" -#include "common.h" -#include "console.h" -#include "cros_board_info.h" -#include "hooks.h" - -#define CPRINTS(format, args...) cprints(CC_SYSTEM, format, ##args) - -/* Cache SSFC on init since we don't expect it to change in runtime */ -static union dedede_cbi_ssfc cached_ssfc; -BUILD_ASSERT(sizeof(cached_ssfc) == sizeof(uint32_t)); - -static void cbi_ssfc_init(void) -{ - if (cbi_get_ssfc(&cached_ssfc.raw_value) != EC_SUCCESS) - /* Default to 0 when CBI isn't populated */ - cached_ssfc.raw_value = 0; - - CPRINTS("Read CBI SSFC : 0x%04X", cached_ssfc.raw_value); -} -DECLARE_HOOK(HOOK_INIT, cbi_ssfc_init, HOOK_PRIO_FIRST); - -enum ec_ssfc_base_sensor get_cbi_ssfc_base_sensor(void) -{ - return (enum ec_ssfc_base_sensor) cached_ssfc.base_sensor; -} - -enum ec_ssfc_lid_sensor get_cbi_ssfc_lid_sensor(void) -{ - return (enum ec_ssfc_lid_sensor) cached_ssfc.lid_sensor; -} diff --git a/board/boten/cbi_ssfc.h b/board/boten/cbi_ssfc.h deleted file mode 100644 index 935049b6ae..0000000000 --- a/board/boten/cbi_ssfc.h +++ /dev/null @@ -1,60 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#ifndef _DEDEDE_CBI_SSFC__H_ -#define _DEDEDE_CBI_SSFC__H_ - -#include "stdint.h" - -/**************************************************************************** - * Dedede CBI Second Source Factory Cache - */ - -/* - * Base Sensor (Bits 0-2) - */ -enum ec_ssfc_base_sensor { - SSFC_SENSOR_BASE_DEFAULT = 0, - SSFC_SENSOR_BMI160 = 1, - SSFC_SENSOR_ICM426XX = 2, - SSFC_SENSOR_LSM6DSM = 3, - SSFC_SENSOR_ICM42607 = 4 -}; - -/* - * Lid Sensor (Bits 3-5) - */ -enum ec_ssfc_lid_sensor { - SSFC_SENSOR_LID_DEFAULT = 0, - SSFC_SENSOR_BMA255 = 1, - SSFC_SENSOR_KX022 = 2, - SSFC_SENSOR_LIS2DWL = 3 -}; - -union dedede_cbi_ssfc { - struct { - uint32_t base_sensor : 3; - uint32_t lid_sensor : 3; - uint32_t reserved_2 : 26; - }; - uint32_t raw_value; -}; - -/** - * Get the Base sensor type from SSFC_CONFIG. - * - * @return the Base sensor board type. - */ -enum ec_ssfc_base_sensor get_cbi_ssfc_base_sensor(void); - -/** - * Get the Lid sensor type from SSFC_CONFIG. - * - * @return the Lid sensor board type. - */ -enum ec_ssfc_lid_sensor get_cbi_ssfc_lid_sensor(void); - - -#endif /* _DEDEDE_CBI_SSFC__H_ */ diff --git a/board/boten/ec.tasklist b/board/boten/ec.tasklist deleted file mode 100644 index be1f92aff2..0000000000 --- a/board/boten/ec.tasklist +++ /dev/null @@ -1,22 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* - * See CONFIG_TASK_LIST in config.h for details. - */ - -#define CONFIG_TASK_LIST \ - TASK_ALWAYS(HOOKS, hook_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(CHARGER, charger_task, NULL, TRENTA_TASK_STACK_SIZE) \ - TASK_NOTEST(CHIPSET, chipset_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, LARGER_TASK_STACK_SIZE) \ - TASK_ALWAYS(HOSTCMD, host_command_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(CONSOLE, console_task, NULL, VENTI_TASK_STACK_SIZE) \ - TASK_ALWAYS(POWERBTN, power_button_task, NULL, ULTRA_TASK_STACK_SIZE) \ - TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, ULTRA_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_C0, pd_task, NULL, ULTRA_TASK_STACK_SIZE) \ - TASK_ALWAYS(PD_INT_C0, pd_interrupt_handler_task, 0, ULTRA_TASK_STACK_SIZE) diff --git a/board/boten/gpio.inc b/board/boten/gpio.inc deleted file mode 100644 index 4e8290c277..0000000000 --- a/board/boten/gpio.inc +++ /dev/null @@ -1,146 +0,0 @@ -/* -*- mode:c -*- - * - * Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Declare symbolic names for all the GPIOs that we care about. - * Note: Those with interrupt handlers must be declared first. */ - -/* Power State interrupts */ -GPIO_INT(SLP_S4_L, PIN(I, 5), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(SLP_S3_L, PIN(H, 3), GPIO_INT_BOTH, baseboard_all_sys_pgood_interrupt) -GPIO_INT(SLP_S0_L, PIN(E, 4), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(SLP_SUS_L, PIN(G, 2), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(VCCIN_AUX_VID0, PIN(D, 0), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(RSMRST_PWRGD_L, PIN(E, 1), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(CPU_C10_GATE_L, PIN(G, 1), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PG_DRAM_OD, PIN(D, 3), GPIO_INT_BOTH, baseboard_all_sys_pgood_interrupt) -GPIO_INT(PG_PP1050_ST_OD, PIN(L, 1), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(VCCIN_AUX_VID1, PIN(K, 1), GPIO_INT_BOTH, power_signal_interrupt) -GPIO_INT(PG_VCCIO_EXT_OD, PIN(D, 7), GPIO_INT_BOTH, baseboard_all_sys_pgood_interrupt) -GPIO_INT(ESPI_RESET_L, PIN(D, 2), GPIO_INT_FALLING | GPIO_SEL_1P8V, espi_reset_pin_asserted_interrupt) - -GPIO_INT(H1_EC_PWR_BTN_ODL, PIN(E, 2), GPIO_INT_BOTH | GPIO_PULL_UP, power_button_interrupt) -#ifdef CONFIG_LOW_POWER_IDLE -/* Used to wake up the EC from Deep Doze mode when writing to console */ -GPIO_INT(UART1_RX, PIN(B, 0), GPIO_INT_BOTH, uart_deepsleep_interrupt) /* UART_DBG_TX_EC_RX */ -#endif - -/* USB-C interrupts */ -GPIO_INT(USB_C0_INT_ODL, PIN(K, 0), GPIO_INT_FALLING | GPIO_PULL_UP, usb_c0_interrupt) /* BC12 and charger */ -GPIO_INT(USB_C0_CCSBU_OVP_ODL, PIN(K, 6), GPIO_INT_FALLING | GPIO_PULL_UP, c0_ccsbu_ovp_interrupt) /* Fault protection */ - -/* Other interrupts */ -GPIO_INT(LID_OPEN, PIN(F, 3), GPIO_INT_BOTH, lid_interrupt) -GPIO_INT(LID_360_L, PIN(A, 7), GPIO_INT_BOTH, gmr_tablet_switch_isr) -GPIO_INT(VOLDN_BTN_ODL, PIN(I, 6), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(VOLUP_BTN_ODL, PIN(I, 7), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(BASE_SIXAXIS_INT_L, PIN(J, 0), GPIO_INT_FALLING | GPIO_SEL_1P8V, lsm6dsm_interrupt) -GPIO_INT(EC_WP_OD, PIN(A, 6), GPIO_INT_BOTH, switch_interrupt) -GPIO_INT(HDMI_HPD_SUB_ODL, PIN(E, 7), GPIO_INT_BOTH, hdmi_hpd_interrupt) - -/* Power sequence GPIOs */ -GPIO(EC_AP_RTCRST, PIN(K, 2), GPIO_OUT_LOW) -GPIO(EC_AP_PWR_BTN_ODL, PIN(B, 6), GPIO_ODR_HIGH) -GPIO(EC_AP_DPWROK, PIN(L, 7), GPIO_OUT_LOW) -GPIO(EC_AP_RSMRST_L, PIN(H, 0), GPIO_OUT_LOW) -GPIO(EC_AP_WAKE_ODL, PIN(D, 5), GPIO_ODR_HIGH) -GPIO(SYS_RST_ODL, PIN(D, 1), GPIO_ODR_HIGH) -GPIO(EC_AP_SYS_PWROK, PIN(F, 2), GPIO_OUT_LOW) -GPIO(PG_PP5000_U_OD, PIN(E, 3), GPIO_INPUT) -GPIO(EN_PP3300_A, PIN(C, 5), GPIO_OUT_LOW) -GPIO(EC_AP_PCH_PWROK_OD, PIN(D, 6), GPIO_ODR_LOW) -GPIO(EN_PP5000_U, PIN(K, 5), GPIO_OUT_LOW) -/* TODO(b:149775160) - Modify if needed if we ever use this signal. */ -GPIO(EN_VCCST, PIN(D, 4), GPIO_INPUT) -GPIO(EN_VCCIO_EXT, PIN(B, 2), GPIO_OUT_LOW) -GPIO(EC_PROCHOT_ODL, PIN(I, 1), GPIO_ODR_HIGH | GPIO_SEL_1P8V) -GPIO(EC_AP_VCCST_PWRGD_OD, PIN(E, 5), GPIO_ODR_LOW) -GPIO(ALL_SYS_PWRGD, PIN(B, 7), GPIO_OUT_LOW) -GPIO(EN_SLP_Z, PIN(K, 3), GPIO_OUT_LOW) - -/* Required for icelake chipset code, but implemented through other means for dedede */ -UNIMPLEMENTED(AC_PRESENT) -UNIMPLEMENTED(PG_EC_DSW_PWROK) -UNIMPLEMENTED(PG_EC_ALL_SYS_PWRGD) - -/* Used by baseboard z-state enable, but not present on boten */ -UNIMPLEMENTED(USB_C1_INT_ODL) - -/* I2C pins - Alternate function below configures I2C module on these pins */ -GPIO(EC_I2C_EEPROM_SCL, PIN(B, 3), GPIO_INPUT) -GPIO(EC_I2C_EEPROM_SDA, PIN(B, 4), GPIO_INPUT) -GPIO(EC_I2C_BATTERY_SCL, PIN(C, 1), GPIO_INPUT) -GPIO(EC_I2C_BATTERY_SDA, PIN(C, 2), GPIO_INPUT) -GPIO(EC_I2C_SENSOR_SCL, PIN(F, 6), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(EC_I2C_SENSOR_SDA, PIN(F, 7), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(EC_I2C_USB_C0_SCL, PIN(A, 4), GPIO_INPUT) -GPIO(EC_I2C_USB_C0_SDA, PIN(A, 5), GPIO_INPUT) - -/* USB pins */ -GPIO(EN_USB_A0_VBUS, PIN(L, 6), GPIO_OUT_LOW) -GPIO(EN_USB_A1_VBUS, PIN(E, 6), GPIO_OUT_LOW) -GPIO(EC_AP_USB_C0_HPD, PIN(L, 4), GPIO_OUT_LOW) -GPIO(EC_AP_USB_C1_HDMI_HPD, PIN(K, 7), GPIO_OUT_LOW) -GPIO(HDMI_SEL_L, PIN(C, 6), GPIO_OUT_LOW) - -/* MKBP event synchronization */ -GPIO(EC_AP_MKBP_INT_L, PIN(L, 5), GPIO_ODR_HIGH) - -/* Misc pins which will run to the I/O board */ - -/* Misc */ -GPIO(EN_BL_OD, PIN(K, 4), GPIO_ODR_LOW) -GPIO(EC_ENTERING_RW, PIN(G, 0), GPIO_OUT_LOW) -GPIO(EC_ENTERING_RW2, PIN(C, 7), GPIO_OUT_LOW) -GPIO(CCD_MODE_ODL, PIN(H, 5), GPIO_ODR_HIGH) -GPIO(EC_BATTERY_PRES_ODL, PIN(I, 4), GPIO_INPUT) -GPIO_INT(PEN_DET_ODL, PIN(J, 1), GPIO_INT_BOTH | GPIO_PULL_UP, pen_detect_interrupt) -GPIO(EN_PP5000_PEN, PIN(B, 5), GPIO_OUT_LOW) -GPIO(PEN_DET_PCH, PIN(F, 1), GPIO_OUT_LOW) -GPIO(EN_KB_BL, PIN(J, 3), GPIO_OUT_LOW) /* Currently unused */ -GPIO(ECH1_PACKET_MODE, PIN(H, 1), GPIO_OUT_LOW) - -/* NC pins, enable internal pull-down to avoid floating state. */ -GPIO(GPIOC0_NC, PIN(C, 0), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOC3_NC, PIN(C, 3), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOC4_NC, PIN(C, 4), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOE0_NC, PIN(E, 0), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOF0_NC, PIN(F, 0), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOF4_NC, PIN(F, 4), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOF5_NC, PIN(F, 5), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOG3_NC, PIN(G, 3), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOG4_NC, PIN(G, 4), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOG5_NC, PIN(G, 5), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOG6_NC, PIN(G, 6), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOG7_NC, PIN(G, 7), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOH4_NC, PIN(H, 4), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOH6_NC, PIN(H, 6), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOJ4_NC, PIN(J, 4), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOJ5_NC, PIN(J, 5), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOJ6_NC, PIN(J, 6), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOL0_NC, PIN(L, 0), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOL2_NC, PIN(L, 2), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOL3_NC, PIN(L, 3), GPIO_INPUT | GPIO_PULL_DOWN) -GPIO(GPIOM6_NC, PIN(M, 6), GPIO_INPUT | GPIO_PULL_DOWN) - -/* Alternate functions GPIO definitions */ -/* UART */ -ALTERNATE(PIN_MASK(B, BIT(0) | BIT(1)), 0, MODULE_UART, 0) /* UART for debug */ - -/* I2C */ -ALTERNATE(PIN_MASK(B, BIT(3) | BIT(4)), 0, MODULE_I2C, 0) /* I2C0 */ -ALTERNATE(PIN_MASK(C, BIT(1) | BIT(2)), 0, MODULE_I2C, 0) /* I2C1 */ -ALTERNATE(PIN_MASK(F, BIT(6) | BIT(7)), 0, MODULE_I2C, GPIO_SEL_1P8V) /* I2C2 - 1.8V */ -ALTERNATE(PIN_MASK(A, BIT(4) | BIT(5)), 0, MODULE_I2C, 0) /* I2C5 */ - -/* ADC */ -ALTERNATE(PIN_MASK(I, BIT(0) | BIT(2) | BIT(3)), 0, MODULE_ADC, 0) /* ADC0: EC_VSNS_PP3300_A, ADC2: TEMP_SENSOR_1, ADC3: TEMP_SENSOR_2 */ - -/* DAC */ -ALTERNATE(PIN_MASK(J, BIT(2)), 0, MODULE_DAC, 0) /* DAC2: EC_AP_PSYS */ - -/* PWM */ -ALTERNATE(PIN_MASK(A, BIT(0) | BIT(1) | BIT(2) | BIT(3)), 0, MODULE_PWM, 0) /* KB_BL_PWM, LED_[R,G,B]_ODL */ diff --git a/board/boten/led.c b/board/boten/led.c deleted file mode 100644 index 93675966b3..0000000000 --- a/board/boten/led.c +++ /dev/null @@ -1,112 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - * - * Boten specific PWM LED settings. - */ - -#include "common.h" -#include "led_onoff_states.h" -#include "led_common.h" -#include "gpio.h" -#include "pwm.h" - -#define LED_OFF_LVL 0 -#define LED_ON_LVL 1 - -__override const int led_charge_lvl_1 = 5; - -__override const int led_charge_lvl_2 = 97; - -__override struct led_descriptor - led_bat_state_table[LED_NUM_STATES][LED_NUM_PHASES] = { - [STATE_CHARGING_LVL_1] = {{EC_LED_COLOR_RED, LED_INDEFINITE} }, - [STATE_CHARGING_LVL_2] = {{EC_LED_COLOR_AMBER, LED_INDEFINITE} }, - [STATE_CHARGING_FULL_CHARGE] = {{EC_LED_COLOR_GREEN, LED_INDEFINITE} }, - [STATE_DISCHARGE_S0] = {{LED_OFF, LED_INDEFINITE} }, - [STATE_DISCHARGE_S3] = {{LED_OFF, LED_INDEFINITE} }, - [STATE_DISCHARGE_S5] = {{LED_OFF, LED_INDEFINITE} }, - [STATE_BATTERY_ERROR] = {{EC_LED_COLOR_RED, 1 * LED_ONE_SEC}, - {LED_OFF, 1 * LED_ONE_SEC} }, - [STATE_FACTORY_TEST] = {{EC_LED_COLOR_RED, 2 * LED_ONE_SEC}, - {EC_LED_COLOR_GREEN, 2 * LED_ONE_SEC} }, -}; - -__override const struct led_descriptor - led_pwr_state_table[PWR_LED_NUM_STATES][LED_NUM_PHASES] = { - [PWR_LED_STATE_ON] = {{EC_LED_COLOR_WHITE, LED_INDEFINITE} }, - [PWR_LED_STATE_SUSPEND_AC] = {{EC_LED_COLOR_WHITE, 3 * LED_ONE_SEC}, - {LED_OFF, 0.5 * LED_ONE_SEC} }, - [PWR_LED_STATE_SUSPEND_NO_AC] = {{EC_LED_COLOR_WHITE, 3 * LED_ONE_SEC}, - {LED_OFF, 0.5 * LED_ONE_SEC} }, - [PWR_LED_STATE_OFF] = {{LED_OFF, LED_INDEFINITE} }, -}; - -const enum ec_led_id supported_led_ids[] = { - EC_LED_ID_BATTERY_LED, - EC_LED_ID_POWER_LED -}; - -const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids); - -__override void led_set_color_power(enum ec_led_colors color) -{ - if (color == EC_LED_COLOR_WHITE) - pwm_enable(PWM_CH_LED_WHITE, LED_ON_LVL); - else - pwm_enable(PWM_CH_LED_WHITE, LED_OFF_LVL); -} - -__override void led_set_color_battery(enum ec_led_colors color) -{ - switch (color) { - case EC_LED_COLOR_RED: - pwm_enable(PWM_CH_LED_RED, LED_ON_LVL); - pwm_enable(PWM_CH_LED_GREEN, LED_OFF_LVL); - break; - case EC_LED_COLOR_AMBER: - pwm_enable(PWM_CH_LED_RED, LED_ON_LVL); - pwm_enable(PWM_CH_LED_GREEN, LED_ON_LVL); - break; - case EC_LED_COLOR_GREEN: - pwm_enable(PWM_CH_LED_RED, LED_OFF_LVL); - pwm_enable(PWM_CH_LED_GREEN, LED_ON_LVL); - break; - default: /* LED_OFF and other unsupported colors */ - pwm_enable(PWM_CH_LED_RED, LED_OFF_LVL); - pwm_enable(PWM_CH_LED_GREEN, LED_OFF_LVL); - break; - } -} - -void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range) -{ - if (led_id == EC_LED_ID_BATTERY_LED) { - brightness_range[EC_LED_COLOR_RED] = 1; - brightness_range[EC_LED_COLOR_AMBER] = 1; - brightness_range[EC_LED_COLOR_GREEN] = 1; - } else if (led_id == EC_LED_ID_POWER_LED) { - brightness_range[EC_LED_COLOR_WHITE] = 1; - } -} - -int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness) -{ - if (led_id == EC_LED_ID_BATTERY_LED) { - if (brightness[EC_LED_COLOR_RED] != 0) - led_set_color_battery(EC_LED_COLOR_RED); - else if (brightness[EC_LED_COLOR_AMBER] != 0) - led_set_color_battery(EC_LED_COLOR_AMBER); - else if (brightness[EC_LED_COLOR_GREEN] != 0) - led_set_color_battery(EC_LED_COLOR_GREEN); - else - led_set_color_battery(LED_OFF); - } else if (led_id == EC_LED_ID_POWER_LED) { - if (brightness[EC_LED_COLOR_WHITE] != 0) - led_set_color_power(EC_LED_COLOR_WHITE); - else - led_set_color_power(LED_OFF); - } - - return EC_SUCCESS; -} diff --git a/board/boten/usb_pd_policy.c b/board/boten/usb_pd_policy.c deleted file mode 100644 index 65ee678263..0000000000 --- a/board/boten/usb_pd_policy.c +++ /dev/null @@ -1,71 +0,0 @@ -/* Copyright 2020 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include "battery_smart.h" -#include "charge_manager.h" -#include "charger.h" -#include "chipset.h" -#include "common.h" -#include "console.h" -#include "driver/charger/isl923x_public.h" -#include "driver/tcpm/tcpci.h" -#include "usb_pd.h" - -#define CPRINTF(format, args...) cprintf(CC_USBPD, format, ## args) -#define CPRINTS(format, args...) cprints(CC_USBPD, format, ## args) - -int pd_check_vconn_swap(int port) -{ - /* Allow VCONN swaps if the AP is on */ - return chipset_in_state(CHIPSET_STATE_ANY_SUSPEND | CHIPSET_STATE_ON); -} - -void pd_power_supply_reset(int port) -{ - if (port != 0) - return; - - /* Disable VBUS */ - tcpc_write(port, TCPC_REG_COMMAND, TCPC_REG_COMMAND_SRC_CTRL_LOW); - - /* Notify host of power info change. */ - pd_send_host_event(PD_EVENT_POWER_CHANGE); -} - -int pd_set_power_supply_ready(int port) -{ - int rv; - - if (port != 0) - return EC_ERROR_INVAL; - - /* Disable charging. */ - rv = tcpc_write(port, TCPC_REG_COMMAND, TCPC_REG_COMMAND_SNK_CTRL_LOW); - if (rv) - return rv; - - /* Our policy is not to source VBUS when the AP is off. */ - if (chipset_in_state(CHIPSET_STATE_ANY_OFF)) - return EC_ERROR_NOT_POWERED; - - /* Provide Vbus. */ - rv = tcpc_write(port, TCPC_REG_COMMAND, TCPC_REG_COMMAND_SRC_CTRL_HIGH); - if (rv) - return rv; - - rv = raa489000_enable_asgate(port, true); - if (rv) - return rv; - - /* Notify host of power info change. */ - pd_send_host_event(PD_EVENT_POWER_CHANGE); - - return EC_SUCCESS; -} - -int pd_snk_is_vbus_provided(int port) -{ - return pd_check_vbus_level(port, VBUS_PRESENT); -} diff --git a/board/boten/vif_override.xml b/board/boten/vif_override.xml deleted file mode 100644 index 32736caf64..0000000000 --- a/board/boten/vif_override.xml +++ /dev/null @@ -1,3 +0,0 @@ -<!-- Add VIF field overrides here. See genvif.c and the Vendor Info File - Definition from the USB-IF. ---> |