diff options
Diffstat (limited to 'board/brask/board.h')
| -rw-r--r-- | board/brask/board.h | 199 |
1 files changed, 0 insertions, 199 deletions
diff --git a/board/brask/board.h b/board/brask/board.h deleted file mode 100644 index 0d92b2c07f..0000000000 --- a/board/brask/board.h +++ /dev/null @@ -1,199 +0,0 @@ -/* Copyright 2021 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Brask board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -#include "compile_time_macros.h" - -/* Baseboard features */ -#include "baseboard.h" - -#define CONFIG_MP2964 - -/* Barrel Jack */ -#define DEDICATED_CHARGE_PORT 3 - -/* HDMI CEC */ -#define CONFIG_CEC -#define CEC_GPIO_OUT GPIO_HDMI_CEC_OUT -#define CEC_GPIO_IN GPIO_HDMI_CEC_IN -#define CEC_GPIO_PULL_UP GPIO_HDMI_CEC_PULL_UP - -/* USB Type A Features */ -#define USB_PORT_COUNT 4 -#define CONFIG_USB_PORT_POWER_DUMB - -/* USB Type C and USB PD defines */ -#define CONFIG_USB_PD_REQUIRE_AP_MODE_ENTRY - -#define CONFIG_IO_EXPANDER -#define CONFIG_IO_EXPANDER_NCT38XX -#define CONFIG_IO_EXPANDER_PORT_COUNT 2 - -#define CONFIG_USB_PD_PPC -#define CONFIG_USB_PD_TCPM_RT1715 -#define CONFIG_USBC_RETIMER_INTEL_BB -/* TODO(b/197505149): need to fix the build error and clarify - * how to set the usb_ls_en_gpio and retimer_rst_gpio - * in the same array. - */ -/* #define CONFIG_USBC_RETIMER_KB800X */ -#define CONFIG_USBC_PPC_SYV682X - -/* TODO: b/177608416 - measure and check these values on brya */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 30000 /* us */ -#define PD_VCONN_SWAP_DELAY 5000 /* us */ - -/* The design should support up to 100W. */ -/* TODO(b/197702356): Set the max PD to 60W now and change it - * to 100W after we verify it. - */ -#define PD_OPERATING_POWER_MW CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON -#define PD_MAX_POWER_MW 100000 -#define PD_MAX_CURRENT_MA 5000 -#define PD_MAX_VOLTAGE_MV 20000 - -/* - * Macros for GPIO signals used in common code that don't match the - * schematic names. Signal names in gpio.inc match the schematic and are - * then redefined here to so it's more clear which signal is being used for - * which purpose. - */ -#define GPIO_AC_PRESENT GPIO_ACOK_OD -#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL -#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL -#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW -#define GPIO_PACKET_MODE_EN GPIO_EC_GSC_PACKET_MODE -#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL -#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L -#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST -#define GPIO_PCH_SLP_S0_L GPIO_SYS_SLP_S0IX_L -#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L - -/* - * GPIO_EC_PCH_INT_ODL is used for MKBP events as well as a PCH wakeup - * signal. - */ -#define GPIO_PCH_WAKE_L GPIO_EC_PCH_INT_ODL -#define GPIO_PG_EC_ALL_SYS_PWRGD GPIO_SEQ_EC_ALL_SYS_PG -#define GPIO_PG_EC_DSW_PWROK GPIO_SEQ_EC_DSW_PWROK -#define GPIO_PG_EC_RSMRST_ODL GPIO_SEQ_EC_RSMRST_ODL -#define GPIO_POWER_BUTTON_L GPIO_GSC_EC_PWR_BTN_ODL -#define GPIO_RSMRST_L_PGOOD GPIO_SEQ_EC_RSMRST_ODL -#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL -#define GPIO_WP_L GPIO_EC_WP_ODL -#define GPIO_RECOVERY_L GPIO_EC_RECOVERY_BTN_OD -#define GPIO_RECOVERY_L_2 GPIO_GSC_EC_RECOVERY_BTN_OD - -/* I2C Bus Configuration */ - -#define I2C_PORT_DP_REDRIVER NPCX_I2C_PORT0_0 - -#define I2C_PORT_USB_C0_C2_TCPC NPCX_I2C_PORT1_0 -#define I2C_PORT_USB_C1_TCPC NPCX_I2C_PORT4_1 - -#define I2C_PORT_USB_C0_C2_PPC NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C1_PPC NPCX_I2C_PORT6_1 - -#define I2C_PORT_USB_C0_C2_BC12 NPCX_I2C_PORT2_0 -#define I2C_PORT_USB_C1_BC12 NPCX_I2C_PORT6_1 - -#define I2C_PORT_USB_C0_C2_MUX NPCX_I2C_PORT3_0 -#define I2C_PORT_USB_C1_MUX NPCX_I2C_PORT6_1 - -#define I2C_PORT_QI NPCX_I2C_PORT5_0 -#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0 -#define I2C_PORT_MP2964 NPCX_I2C_PORT7_0 - -#define I2C_ADDR_EEPROM_FLAGS 0x50 - -#define I2C_ADDR_MP2964_FLAGS 0x20 - -/* - * see b/174768555#comment22 - */ -#define USBC_PORT_C0_BB_RETIMER_I2C_ADDR 0x56 -#define USBC_PORT_C2_BB_RETIMER_I2C_ADDR 0x57 - -/* Enabling Thunderbolt-compatible mode */ -#define CONFIG_USB_PD_TBT_COMPAT_MODE - -/* Enabling USB4 mode */ -#define CONFIG_USB_PD_USB4 - -/* Retimer */ -#define CONFIG_USBC_RETIMER_FW_UPDATE - -/* Thermal features */ -#define CONFIG_THERMISTOR -#define CONFIG_TEMP_SENSOR -#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_SEQ_EC_DSW_PWROK -#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B - -/* ADC */ -#define CONFIG_ADC - -/* - * TODO(b/197478860): Enable the fan control. We need - * to check the sensor value and adjust the fan speed. - */ -/* #define CONFIG_FANS FAN_CH_COUNT */ - -/* Include math_util for bitmask_uint64 used in pd_timers */ -#define CONFIG_MATH_UTIL - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" /* needed by registers.h */ -#include "registers.h" -#include "usbc_config.h" - -enum adc_channel { - ADC_TEMP_SENSOR_1_CPU, - ADC_TEMP_SENSOR_2_CPU_VR, - ADC_TEMP_SENSOR_3_WIFI, - ADC_TEMP_SENSOR_4_DIMM, - ADC_VBUS, - ADC_CH_COUNT -}; - -enum temp_sensor_id { - TEMP_SENSOR_1_CPU, - TEMP_SENSOR_2_CPU_VR, - TEMP_SENSOR_3_WIFI, - TEMP_SENSOR_4_DIMM, - TEMP_SENSOR_COUNT -}; - -enum ioex_port { - IOEX_C0_NCT38XX = 0, - IOEX_C2_NCT38XX, - IOEX_PORT_COUNT -}; - -enum pwm_channel { - PWM_CH_LED_GREEN, /* PWM0 */ - PWM_CH_FAN, /* PWM5 */ - PWM_CH_LED_RED, /* PWM2 */ - PWM_CH_COUNT -}; - -enum fan_channel { - FAN_CH_0 = 0, - FAN_CH_COUNT -}; - -enum mft_channel { - MFT_CH_0 = 0, - MFT_CH_COUNT -}; - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ |