1 files changed, 0 insertions, 155 deletions
diff --git a/board/burnet/board.h b/board/burnet/board.h
deleted file mode 100644
index 009da83ac5..0000000000
--- a/board/burnet/board.h
+++ /dev/null
@@ -1,155 +0,0 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Configuration for Burnet */
-
-#ifndef __CROS_EC_BOARD_H
-#define __CROS_EC_BOARD_H
-
-#define VARIANT_KUKUI_JACUZZI
-#define VARIANT_KUKUI_BATTERY_SMART
-#define VARIANT_KUKUI_CHARGER_ISL9238
-#define VARIANT_KUKUI_EC_STM32F098
-
-#ifndef SECTION_IS_RW
-#define VARIANT_KUKUI_NO_SENSORS
-#endif /* SECTION_IS_RW */
-
-#include "baseboard.h"
-
-#undef CONFIG_CHIPSET_POWER_SEQ_VERSION
-#define CONFIG_CHIPSET_POWER_SEQ_VERSION 1
-
-#define CONFIG_BATTERY_HW_PRESENT_CUSTOM
-#define CONFIG_BATTERY_VENDOR_PARAM
-
-#define CONFIG_CHARGER_PSYS
-
-#define CONFIG_BC12_DETECT_PI3USB9201
-
-#define CONFIG_EXTPOWER_GPIO
-#undef CONFIG_EXTPOWER_DEBOUNCE_MS
-#define CONFIG_EXTPOWER_DEBOUNCE_MS 200
-
-#define CONFIG_I2C_BITBANG
-#define I2C_BITBANG_PORT_COUNT 1
-#undef CONFIG_I2C_NACK_RETRY_COUNT
-#define CONFIG_I2C_NACK_RETRY_COUNT 10
-#define CONFIG_SMBUS_PEC
-
-#define CONFIG_USB_PD_TCPM_FUSB302
-#define CONFIG_USB_PD_DISCHARGE_GPIO
-#define CONFIG_USB_PD_TCPC_LOW_POWER
-
-#define CONFIG_USB_MUX_IT5205
-
-/* Motion Sensors */
-#ifndef VARIANT_KUKUI_NO_SENSORS
-#define CONFIG_ACCEL_BMA255		/* Lid accel */
-#define CONFIG_ACCEL_KX022
-#define CONFIG_ACCELGYRO_BMI160		/* Base accel */
-#define CONFIG_ACCEL_INTERRUPTS
-#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
-	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
-/* ICM426XX Base accel/gyro */
-#define CONFIG_ACCELGYRO_ICM426XX
-#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \
-	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
-#define CONFIG_ALS
-#define CONFIG_CMD_ACCEL_INFO
-#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT
-
-#define CONFIG_LID_ANGLE
-#define CONFIG_LID_ANGLE_UPDATE
-#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
-#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
-
-#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
-
-#endif /* VARIANT_KUKUI_NO_SENSORS */
-
-/* I2C ports */
-#define I2C_PORT_BC12               0
-#define I2C_PORT_TCPC0              0
-#define I2C_PORT_USB_MUX            0
-#define I2C_PORT_BATTERY            2
-#define I2C_PORT_CHARGER            1
-#define I2C_PORT_SENSORS            1
-#define IT8801_KEYBOARD_PWM_I2C_PORT 1
-#define I2C_PORT_VIRTUAL_BATTERY    I2C_PORT_BATTERY
-
-/* IT8801 I2C address */
-#define IT8801_KEYBOARD_PWM_I2C_ADDR_FLAGS    IT8801_I2C_ADDR1
-
-/* Enable Accel over SPI */
-#define CONFIG_SPI_ACCEL_PORT    0  /* The first SPI master port (SPI2) */
-
-#define CONFIG_KEYBOARD_PROTOCOL_MKBP
-#define CONFIG_MKBP_EVENT
-#define CONFIG_MKBP_USE_GPIO
-
-#ifndef __ASSEMBLER__
-
-enum adc_channel {
-	/* Real ADC channels begin here */
-	ADC_BOARD_ID = 0,
-	ADC_EC_SKU_ID,
-	ADC_CH_COUNT
-};
-
-/* power signal definitions */
-enum power_signal {
-	AP_IN_S3_L,
-	PMIC_PWR_GOOD,
-
-	/* Number of signals */
-	POWER_SIGNAL_COUNT,
-};
-
-/* Motion sensors */
-enum sensor_id {
-	LID_ACCEL = 0,
-	BASE_ACCEL,
-	BASE_GYRO,
-	SENSOR_COUNT,
-};
-
-enum charge_port {
-	CHARGE_PORT_USB_C,
-};
-
-enum battery_type {
-	BATTERY_DYNAPACK_ATL,
-	BATTERY_DYNAPACK_COS,
-	BATTERY_SIMPLO_COS,
-	BATTERY_SIMPLO_HIGHPOWER,
-	BATTERY_SAMSUNG_SDI,
-	BATTERY_COS,
-	BATTERY_TYPE_COUNT,
-};
-
-#include "gpio_signal.h"
-#include "registers.h"
-
-#ifdef SECTION_IS_RO
-/* Interrupt handler for emmc task */
-void emmc_cmd_interrupt(enum gpio_signal signal);
-#endif
-
-void bc12_interrupt(enum gpio_signal signal);
-void board_reset_pd_mcu(void);
-int board_get_version(void);
-
-/* returns the i2c port number of charger */
-int board_get_charger_i2c(void);
-
-int board_is_convertible(void);
-
-/* Motion sensor interrupt */
-void sensor_interrupt(enum gpio_signal signal);
-
-#endif /* !__ASSEMBLER__ */
-
-#endif /* __CROS_EC_BOARD_H */