diff options
Diffstat (limited to 'board/coral/board.h')
| -rw-r--r-- | board/coral/board.h | 309 |
1 files changed, 0 insertions, 309 deletions
diff --git a/board/coral/board.h b/board/coral/board.h deleted file mode 100644 index 24b0ecf86e..0000000000 --- a/board/coral/board.h +++ /dev/null @@ -1,309 +0,0 @@ -/* Copyright 2016 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -/* Coral board configuration */ - -#ifndef __CROS_EC_BOARD_H -#define __CROS_EC_BOARD_H - -/* - * By default, enable all console messages except Events: - * The sensor stack is generating a lot of activity. - */ -#define CC_DEFAULT (CC_ALL & ~CC_MASK(CC_EVENTS)) -#undef CONFIG_HOSTCMD_DEBUG_MODE -#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF - - -/* EC console commands */ -#define CONFIG_CMD_ACCELS -#define CONFIG_CMD_ACCEL_INFO -#define CONFIG_CMD_BATT_MFG_ACCESS -#define CONFIG_CMD_CHARGER_ADC_AMON_BMON -#define CONFIG_CHARGER_SENSE_RESISTOR 10 -#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 -#define BD9995X_IOUT_GAIN_SELECT \ - BD9995X_CMD_PMON_IOUT_CTRL_SET_IOUT_GAIN_SET_20V - -#define CONFIG_CHARGER_PSYS_READ -#define BD9995X_PSYS_GAIN_SELECT \ - BD9995X_CMD_PMON_IOUT_CTRL_SET_PMON_GAIN_SET_02UAW - -#define CONFIG_CMD_I2C_STRESS_TEST -#define CONFIG_CMD_I2C_STRESS_TEST_ACCEL -#define CONFIG_CMD_I2C_STRESS_TEST_ALS -#define CONFIG_CMD_I2C_STRESS_TEST_BATTERY -#define CONFIG_CMD_I2C_STRESS_TEST_CHARGER -#define CONFIG_CMD_I2C_STRESS_TEST_TCPC - -/* Port80 */ -#undef CONFIG_PORT80_HISTORY_LEN -#define CONFIG_PORT80_HISTORY_LEN 256 - -/* Battery */ -#define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION" -#define CONFIG_BATTERY_CUT_OFF -#define CONFIG_BATTERY_HW_PRESENT_CUSTOM -#define CONFIG_BATTERY_LEVEL_NEAR_FULL 94 -#define CONFIG_BATTERY_PRESENT_CUSTOM -#define CONFIG_BATTERY_SMART - -/* Charger */ -#define CONFIG_CHARGE_MANAGER -#define CONFIG_CHARGE_RAMP_SW -#define CONFIG_CHARGE_STATE_DEBUG -#define CONFIG_CHARGER -#define CONFIG_CHARGER_BD9995X -#define CONFIG_CHARGER_BD9995X_CHGEN -#define CONFIG_CHARGER_DISCHARGE_ON_AC -#define CONFIG_CHARGER_INPUT_CURRENT 512 -#define CONFIG_CHARGER_MAINTAIN_VBAT -#undef CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON -#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 1 -#define CONFIG_USB_CHARGER -#define CONFIG_CHARGER_PROFILE_OVERRIDE -#define CONFIG_CHARGE_MANAGER_EXTERNAL_POWER_LIMIT - -/* USB-A config */ -#define CONFIG_USB_PORT_POWER_SMART -#define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP -#define CONFIG_USB_PORT_POWER_SMART_SIMPLE -#undef CONFIG_USB_PORT_POWER_SMART_PORT_COUNT -#define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1 -#define GPIO_USB1_ILIM_SEL GPIO_USB_A_CHARGE_EN_L -#define GPIO_USB_CTL1 GPIO_EN_PP5000 - -#define CONFIG_TABLET_MODE - -/* USB PD config */ -#define CONFIG_HOSTCMD_PD_CONTROL -#define CONFIG_USB_PD_ALT_MODE -#define CONFIG_USB_PD_ALT_MODE_DFP -#define CONFIG_USB_PD_DUAL_ROLE -#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE -#define CONFIG_USB_PD_DISCHARGE_TCPC -#define CONFIG_USB_PD_LOGGING -#define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0 -#define CONFIG_USB_PD_PORT_MAX_COUNT 2 -#define CONFIG_USB_PD_VBUS_DETECT_CHARGER -#define CONFIG_USB_PD_TCPC_LOW_POWER -#define CONFIG_USB_PD_TCPM_MUX /* for both PS8751 and ANX3429 */ -#define CONFIG_USB_PD_TCPM_ANX3429 -#define CONFIG_USB_PD_TCPM_PS8751 -#define CONFIG_USB_PD_TCPM_TCPCI -#define CONFIG_USB_PD_TRY_SRC -#define CONFIG_USB_POWER_DELIVERY -#define CONFIG_USB_PD_TCPMV1 -#define CONFIG_USB_PD_COMM_LOCKED - -#define CONFIG_USBC_SS_MUX -#define CONFIG_USBC_SS_MUX_DFP_ONLY -#define CONFIG_USBC_VCONN -#define CONFIG_USBC_VCONN_SWAP - -/* SoC / PCH */ -#define CONFIG_HOSTCMD_LPC -#define CONFIG_CHIPSET_APOLLOLAKE -#define CONFIG_CHIPSET_RESET_HOOK -#define CONFIG_POWER_BUTTON -#define CONFIG_POWER_BUTTON_X86 -#define CONFIG_POWER_COMMON -#define CONFIG_POWER_S0IX -#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE - -/* EC */ -#define CONFIG_ADC -#define CONFIG_EXTPOWER_GPIO -#undef CONFIG_EXTPOWER_DEBOUNCE_MS -#define CONFIG_EXTPOWER_DEBOUNCE_MS 1000 -#define CONFIG_FPU -/* Region sizes are not a power of 2 so we can't use MPU */ -#undef CONFIG_MPU -#define CONFIG_HOSTCMD_FLASH_SPI_INFO -#define CONFIG_I2C -#define CONFIG_I2C_CONTROLLER - -#define CONFIG_KEYBOARD_PROTOCOL_8042 -#define CONFIG_KEYBOARD_COL2_INVERTED -#define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2 -#define CONFIG_LED_COMMON -#define CONFIG_LID_SWITCH -#define CONFIG_LOW_POWER_IDLE -#define CONFIG_LTO -#define CONFIG_POWER_SIGNAL_INTERRUPT_STORM_DETECT_THRESHOLD 30 -#define CONFIG_PWM -#define CONFIG_PWM_KBLIGHT -#define CONFIG_TEMP_SENSOR -#define CONFIG_THERMISTOR_NCP15WB -#define CONFIG_STEINHART_HART_3V3_13K7_47K_4050B -#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B -#define CONFIG_DPTF -#define CONFIG_SCI_GPIO GPIO_PCH_SCI_L -#define CONFIG_VBOOT_HASH -#define CONFIG_VOLUME_BUTTONS -#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL -#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL -#define CONFIG_BACKLIGHT_LID -#define CONFIG_WIRELESS -#define CONFIG_WIRELESS_SUSPEND EC_WIRELESS_SWITCH_WLAN_POWER -#define CONFIG_WLAN_POWER_ACTIVE_LOW -#define WIRELESS_GPIO_WLAN_POWER GPIO_WIRELESS_GPIO_WLAN_POWER -#define CONFIG_PWR_STATE_DISCHARGE_FULL - -/* - * During shutdown sequence TPS65094x PMIC turns off the sensor rails - * asynchronously to the EC. If we access the sensors when the sensor power - * rails are off we get I2C errors. To avoid this issue, defer switching - * the sensors rate if in S3. By the time deferred function is serviced if - * the chipset is in S5 we can back out from switching the sensor rate. - * - * Time taken by V1P8U rail to go down from S3 is 30ms to 60ms hence defer - * the sensor switching after 60ms. - */ -#undef CONFIG_MOTION_SENSE_SUSPEND_DELAY_US -#define CONFIG_MOTION_SENSE_SUSPEND_DELAY_US (MSEC * 60) - -#define CONFIG_FLASH_SIZE_BYTES 524288 -#define CONFIG_SPI_FLASH_REGS -#define CONFIG_SPI_FLASH_W25Q40 /* FIXME: Should be GD25LQ40? */ - -/* - * Enable 1 slot of secure temporary storage to support - * suspend/resume with read/write memory training. - */ -#define CONFIG_VSTORE -#define CONFIG_VSTORE_SLOT_COUNT 1 - -/* Optional feature - used by nuvoton */ -#define NPCX_UART_MODULE2 1 /* 0:GPIO10/11 1:GPIO64/65 as UART */ -#define NPCX_JTAG_MODULE2 0 /* 0:GPIO21/17/16/20 1:GPIOD5/E2/D4/E5 as JTAG*/ -/* FIXME(dhendrix): these pins are just normal GPIOs on Coral. Do we need - * to change some other setting to put them in GPIO mode? */ -#define NPCX_TACH_SEL2 0 /* 0:GPIO40/73 1:GPIO93/A6 as TACH */ - -/* I2C ports */ -#define I2C_PORT_GYRO NPCX_I2C_PORT1 -#define I2C_PORT_LID_ACCEL NPCX_I2C_PORT2 -#define I2C_PORT_BATTERY NPCX_I2C_PORT3 -#define I2C_PORT_CHARGER NPCX_I2C_PORT3 -/* Accelerometer and Gyroscope are the same device. */ -#define I2C_PORT_ACCEL I2C_PORT_GYRO - -/* Sensors */ -#define CONFIG_MKBP_EVENT -#define CONFIG_MKBP_USE_HOST_EVENT -#define CONFIG_ACCELGYRO_BMI160 -#define CONFIG_ACCEL_INTERRUPTS -#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \ - TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL) -#define CONFIG_MAG_CALIBRATE -#define CONFIG_ACCEL_KX022 -#define CONFIG_LID_ANGLE -#define CONFIG_LID_ANGLE_UPDATE -#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL -#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL -#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT - -/* Enable sensor fifo, must also define the _SIZE and _THRES */ -#define CONFIG_ACCEL_FIFO -/* FIFO size is in power of 2. */ -#define CONFIG_ACCEL_FIFO_SIZE 512 -/* Depends on how fast the AP boots and typical ODRs */ -#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) - - -#ifndef __ASSEMBLER__ - -#include "gpio_signal.h" -#include "registers.h" - -/* ADC signal */ -enum adc_channel { - ADC_TEMP_SENSOR_CHARGER, /* ADC0 */ - ADC_TEMP_SENSOR_AMB, /* ADC1 */ - ADC_BOARD_ID, /* ADC2 */ - ADC_BOARD_SKU_1, /* ADC3 */ - ADC_BOARD_SKU_0, /* ADC4 */ - ADC_CH_COUNT -}; - -enum pwm_channel { - PWM_CH_KBLIGHT = 0, - /* Number of PWM channels */ - PWM_CH_COUNT -}; - -enum temp_sensor_id { - TEMP_SENSOR_BATTERY = 0, - TEMP_SENSOR_AMBIENT, - TEMP_SENSOR_CHARGER, - TEMP_SENSOR_COUNT -}; - -/* - * Motion sensors: - * When reading through IO memory is set up for sensors (LPC is used), - * the first 2 entries must be accelerometers, then gyroscope. - * For BMI160, accel, gyro and compass sensors must be next to each other. - */ -enum sensor_id { - LID_ACCEL, - BASE_ACCEL, - BASE_GYRO, - SENSOR_COUNT, -}; - -#define CONFIG_HOSTCMD_SKUID -enum coral_board_version { - BOARD_VERSION_UNKNOWN = -1, - BOARD_VERSION_1, - BOARD_VERSION_2, - BOARD_VERSION_3, - BOARD_VERSION_4, - BOARD_VERSION_5, - BOARD_VERSION_6, - BOARD_VERSION_7, - BOARD_VERSION_8, - BOARD_VERSION_9, - BOARD_VERSION_10, - BOARD_VERSION_11, - BOARD_VERSION_12, - BOARD_VERSION_13, - BOARD_VERSION_14, - BOARD_VERSION_15, - BOARD_VERSION_16, - BOARD_VERSION_COUNT, -}; - -/* TODO: determine the following board specific type-C power constants */ -/* FIXME(dhendrix): verify all of the below PD_* numbers */ -/* - * delay to turn on the power supply max is ~16ms. - * delay to turn off the power supply max is about ~180ms. - */ -#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */ -#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */ - -/* delay to turn on/off vconn */ - -/* Define typical operating power and max power */ -#define PD_OPERATING_POWER_MW 15000 -#define PD_MAX_POWER_MW 45000 -#define PD_MAX_CURRENT_MA 3000 -#define PD_MAX_VOLTAGE_MV 20000 - -/* Reset PD MCU */ -void board_reset_pd_mcu(void); - -int board_get_version(void); - -void board_set_tcpc_power_mode(int port, int mode); - -/* Sensors without hardware FIFO are in forced mode */ -#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL) - -#endif /* !__ASSEMBLER__ */ - -#endif /* __CROS_EC_BOARD_H */ |